Search Documents

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By Esaki M, Nishimura K

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

Opening AddressThank you for inviting me here today to open what promises to be a significant conference on the technological aspects of extractive metallurgy. I would especially like. to welcome delegates who have travelled great distances in order to contribute to, and be participants in, this examination of the technical innovations which have always been a crucial part of our industry.

Jan 1, 1992

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

By Bartosiewicz H

A method for the determination of the gas content of coal seams is presented which improves upon existing methods. The method makes use of a gravitational technique for measurement of the gas desorbed. The amount of lost gas is estimated by determining an empirical relationship relating the desorption of gas with time for each sample separately. This is to replace the assumption that desorp- tion follows a square root law with time. Laboratory investigations have been conducted which indicate that the square root desorption law does not hold good for carbon dioxide. Results of investigations on various factors influencing the technique are presented. It is shown that co-efficients of the empirical equation are dependent upon the elapsed time and the period of observation. Data about gas pressure measurements is presented and it is concluded that gas pressure can be approxi- mated to 0.6 times the pressure below a column of water equal to the depth of cover. This estimate is good enough for adsorption tests to evaluate desorption co-efficients. The technique for repressurisation of the sample,

Jan 1, 1982

By Dods G. H, Hewitt W. V

Ashton Mining Limited is currently one of the active companies undertaking gold exploration in Indonesia. Presently 7 Contract of Work areas are being explored for hard rock and alluvial gold. Hard rock exploration is focussed on the Tertiary volcanic arc terrains in which a variety of epithermal mineralisation styles have been identified. At the regional stage remote sensing techniques using Landsat, Spot and SLAR imagery where available, and photogeological studies are carried out in parallel with regional reconnaissance fieldwork programmes. These involve geological mapping and geochemical drainage sampling. Remote sensing techniques have proven useful in both the extrapolation of known geology and the identification of tectonically favourable settings as controls to mineralisation and volcanicity. The variety of mineralisation styles and settings is reflected in the highly variable geochemical signatures encountered. This has necessitated the refinement of sampling methods and sample preparation techniques for pan concentrate, stream sediment and soil samples in specific project areas. At the detailed prospect stage, mapping with particular attention to structural controls, wallrock alteration assemblages identified by petrog- raphy and XRD clay mineralogy, have proved useful in focussing drill targets. Drilling to date has utilised conventional diamond core drilling methods, the use of lightweight, man-portable "Winkie"-type rigs and hammer auger bedrock sampling systems. Geophysics methods successfully employed on various projects have included airborne magnetics and radiometrics, detailed ground magnetic surveys, VLF-EM and SIROTEM.

Jan 1, 1991

By Hale C. T, Carnie W. A

Rosebery mine has had over 100 years of mining activity. The reserve has remained static for the last eight years with an expected mine life of six years. A move to rectify this was made in 1994 with the birth of the Deep Exploration Project (DEP). $45 M was committed to drill 100 km of underground exploration diamond drilling and develop 5.5 kin of decline aiming to add 9.5 Mt to the reserves and minimise lead time for development of P and K lenses discovered in the early-1990s. In 1996 this aim was expanded with the objective to build the resource base to 20 Mt by June 2000 allowing the mill to operate at 1.0 Mtpa (0.9 Mt from underground). Preliminary results of the project to-date are outlined and exploration diamond drilling techniques and strategies are described.

Jan 1, 1997

As partition curves are widely employed to characterize screening efficiency which, by definition, should include a time parameter, it is shown, perhaps for the first time, that time is already included in the partition curves and how. Laboratory and plant results are used to show how screening efficiency depends on feed composition, near-mesh and oversize material and screen motion, and how these factors may combine to give an erroneous result that two identically efficient screens are different and two screens of different efficiency are identical. Reasons are given which show why a renewed interest in screening would benefit not only screen engineers and operators but also those concerned in formulating standard specifications of screen analysis methods.

Jan 1, 1984

By Jones JJ

A laboratory study of size segregation is described using a model of a Paul Wurth hopper industrailly employed for blast furnace charg- ing purposes. Experimental charge materials used in the study were glass ballotin.i (1-4mm dia.) and sinter fines (0.25-4mm). The tracer material employed consisted of coloured glass beads. The results of the study show that the discharge stream from a Paul Wurth hopper is characterised by an initial negative segregation followed by a positive segregation and that this segregation pattern is a property of the hopper geometry and the filling conditions. A simple computer model based on experimental tracer concentration results is proposed. The measured segregation results and those predicted by the model show close agreement. Application of the results with special reference to the effect of size segregation on charge permeability in blast furnaces is also included.

Jan 1, 1984

By N Anderson

The world-class Golden Mile gold deposit in the Eastern Goldfields of Western Australia is part of the Kalgoorlie Consolidated Gold Mines (KCGM) operation, which is wholly owned by Northern Star Resources Limited. Current mining operations across the Golden Mile is dominated by the large Fimiston Open Pit, which is over 4 km long, 1 km wide and 600 m deep. It is part of a larger mineralised system that stretches over 8 km and includes the Mt Charlotte Underground Mine, which is also operated by KCGM, as well as numerous historical open pit and underground mines. This mineralised system has been continuously mined for over 125 years and is set to continue well into the future. The Golden Mile deposit is in the Norseman Wiluna Greenstone Belt which is made up of a series of mafic volcanic and sedimentary rocks that have been structurally deformed and intruded by granitic rocks. There are two main styles of mineralisation across the Golden Mile. Firstly, the Fimiston style, which consists of shear hosted Golden Mile lodes with abundant sulfides and tellurides and secondly, the Charlotte style that comprises younger stockwork veins. Fimiston style mineralisation is the primary style of mineralisation within the Fimiston Open Pit. Historically, in excess of 3500 m of underground development and over 755 stopes were mined prior to the consolidation of the area and the commencement of Fimiston Open Pit operation. Old underground workings, known as voids, are either empty or backfilled and extend to more than 1.2 km below surface. Although they are a routine part of mining operations at KCGM, voids pose a significant challenge for the geology team in terms of planning and executing exploration and grade control drilling, geological modelling, grade and tonnage estimation, drill and blast design and execution, marking up ore block designs, mining, and reconciliation. This paper will discuss the various challenges faced by the geology team due to the presence of voids, solutions used to overcome some of these challenges and the results of these activities.

Mar 22, 2022

By P Holt, M Allen

On the first of July, 2012, the Australian GovernmentÆs Clean Energy Act commenced. From this point, a price of $23/t of CO2-e will apply to facilities that trip the liability threshold. This first part of this paper concentrates on the mechanics of the Clean Energy Future legislation and how it will be applied to the mining and mineral processing industry.The second part of this paper contains analysis of the data presented for typical mine operations. Methodologies for constructing a carbon strategy are also presented. This will entail determining what the objectives of the carbon strategy are, and defining what the strategic priorities for a business should be. An action plan to address the risks identified from the Clean Energy Act is also developed as part of the strategy.Details such as the advantages and disadvantages of opting into the carbon price scheme for liquid fuels are shown. Other considerations such as the ability to acquire permits through the carbon farming initiative or through overseas clean development mechanism projects are explained.CITATION:Allen, M and Holt, P, 2012. Implications of the carbon price and developing a carbon strategy, in Proceedings International Mine Management 2012, pp 105-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

The long-term outlook Tor Australla's traditional mining products is for flat demand and continuing low prices. This has come about because of three far-reaching changes since earlier boom days: 1. Continuing declines in intensity of usage of basic mine products; 2. The failure of newer western and third world developing countries to realise growth expectations; and 3. Continued production pressure from third world countries (and first-world primary producers) in an effort to earn foreign exchange and rectify trade balances. These trends have led to a general situation of excess supply and weak demand. In this environment, the prerequisites for survival in the mining sector are first-class mines, modern and efficient production methods, low unit costs, aggressive marketing, and products with reasonable operating margins. Many of Australia's mines meet these prerequisites. Following the A$ depreciation and widespread unit cost reductions, most of these mines will be moderately profitable at current depressed commodity prices. They are well placed to benefit from price rises if these eventuate. A new generation of mines is concentrating on a more profitable product range (gold, diamonds, uranium, mineral sands). Australia's balance of trade remains firmly dependent on the primary mining and agricultural industries (Fig. 1). Despite optimistic talk of high-tech developments, tourism and a resurgence of manufacturing, these will remain a small component of Australia's export structure.

Jan 1, 1987

By S B. Fitch, S A. Wilson, A J. R Barr, P R. Searle

Improving the safety culture and performance of any operation is a fundamental goal of every mine operator. Methods of implementing, or changing a culture have developed from the early methods of operant conditioning, for example rewarding crews for achieving nominated safety milestones i.e. 3 months Lost Time Injury (LTI) free through to the current model of engaging a workforce through education and empowerment. As a large scale and mature operation with multiple contractors, Telfer has been exposed to numerous programs throughout its history. This has provided the opportunity to build on and complement these systems by integrating key elements from each. SAFE 360° is a new approach developed to engage the workforce in a holistic approach to encourage positive behaviours across all facets of an individual’s life which results in a focus on situational awareness at all times, rather than being workplace specific. It is based on three key modules: • Emotional Intelligence • Mindfulness • Situational Awareness Each module has a series of modules that help enhance the individual’s sense of self, leading to an ability to self-reflect and self-manage whilst empowering them with the moral courage to challenge their peers to raise standards. Since commencing this SAFE 360° behavioural safety risk management journey in November 2017, we have witnessed a change in the way our workforce engages with each other, their workplace and with management. There has been an increase in hazard perception, identification and ownership of issues, and we have seen a significant decrease in site TRIFR rate from 13.7 to 5.7 (as of April 2019). This paper will provide an overview of the program, how it has been implemented, case studies to demonstrate outcomes and KPIs used to measure effectiveness.

Mar 15, 2021

By Hommert P. J, Brown B

Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. An improved damage model based on microcrack growth in tension allows finite element calculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model.

Jan 1, 1990

The statistical nature of the variability in detonation times of pyrotechnic delays is discussed, and how to evaluate the probability of required detonation intervals is shown. Some methods (analytical and stochastic) are given for designing blasts to ensure that any adverse effects on the variability in the delays is taken into account and minimised. Using computer models of blasts, detonation simulations can be used to check the initiation sequence for the probability of sequence reversals, indicating areas of high blast damage potential. Charge consumption rates, which relate directly to the resulting vibration levels, can be examined for their susceptibility to variation from delay variability. Models that synthesize vibration waveforms for production blasts, when taking delay variability into account, indicate the difficulty in vibration level prediction.

Jan 1, 1992

Among countries afflicted with insLantaneous outbursts of coal and gas, Australia is noteworthy because of lesser disturbances of the seams and of the occurrence of CO2 in the seam gas from place to place. Research sLarted with the 1954 occurrences at Collinsville and Metropolitan Collieries leading to early publications reviewing the problem, describing occurrences and assessing variations in proneness factors in the two affected coal basins.The basic requirements for proneness include coals of high gas sorptive capacity, high ground stress, use of a mining method which provides higher stress concentrations and limits emission of seam gas, including high rates of advance. With CO2 in the seam gas proneness is greater.The mechanism is complex and not fully understood, but involves the coal, the roof, the floor, the gas, the mine opening, the ventilation, the kind of work and the rate of work. Geological disturbances such as faults and dykes increase proneness and tend to localise occurrences. On-occurrence of outbursts in some mines is difficult to explain.Outbursts are seen as a continuing threat to modem deep Australian mining of high rank coal.The simplest contributory factor to reduce is gassiness - despite the low permeability of outbursting coals - and present practices are showing promise. The greatest challenges for the future are partial degasification to below a known threshold figure and confirmation that this reduction is achieved and identification of anomalous geological structures ahead, the most likely locations for instantaneous outbursts to occur. The advances made to date give promise of a future with reducing experiences of uncontrolled instantaneous outbursts. For the Bulli seam particularly, working to achieve prediction and prevention is most urgent.

Jan 1, 1993

By Renwick MT

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in- situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By Osorio J. D C, McMahon M. D

Burwood Beach Sewage Ocean Outfall is being constructed by the Hunter District Water Board as part of an amplification scheme to eliminate pollution from adjacent bathing beaches. The outfall consists of a 93m vertical shaft, 1950m of 2.7m diameter tunnel with a series of diffuser outlets connecting the seaward end of the tunnel to the sea floor on a rock outcrop. The site of the work is in the Newcastle Coal Measures and the project is complicated by the proximity of colliery workings to tunnel alignment, although the colliery records provided valuable information on geological features. The location of the tunnel was determined to be in the Waratah Sandstone Formation immediately below the colliery workings after three different alternatives were considered. The shaft, which will be sized to suit contractor's construction methods and equipment, will be sunk through about 24.5m of alluvial material and 68.5m of rock. The tender documents were developed to allow the contractor considerable flexibility in construction method to suit available equipment. The specification also allowed great flexibility in tunnel construction method with minimum cross sectional area of 5.7m2 being the basis for a number of allowable alternative profiles ranging from circular to horseshoe.

Jan 1, 1987