Search Documents

By R C. Cox

The Brukunga pyrite mine was operated from 1955 to 1972 to supply feedstock for sulfuric acid production in the South Australian fertilizer industry. Iron sulfide ore, mined by Nairne Pyrite Ltd, was finely crushed and concentrated onsite with the concentrates being sent by road and rail to Port Adelaide for roasting. Waste rock was dumped at two locations on the western side of Dawesley Creek and the tailings pumped to a valley-fill storage facility on the eastern side. Production of 1.5 Mt concentrate resulted in 3.5 Mt tailings and 8 Mt waste rock. The site has been administered by the South Australian Government since August 1977 and a lime treatment plant has been operated on the site since September 1980. Environmental issues arising from these operations included: diversion of Dawesley Creek to accommodate the waste rock dumps; dumping of low-grade sulfidic ore in waste rock dumps at the angle of repose immediately adjacent to Dawesley Creek; exposed fresh sulfide mineralisation in the quarry floor; tailings storage facility dam wall constructed by upstream up-lift using tailings and waste rock; an acid water pond sited on the tailings; and pollution of natural drainage. As a result, the minesite rapidly became a source of acid drainage and potential contaminants (sulfate, Al, Fe, Mn, Cd, Zn, and Ni). Various Government bodies have been responsible for considerable effort and expenditure in reducing the flow of acid seepage and contaminants into Dawesley Creek. Presently an estimated 60 per cent of seepage from the waste rock dumps, tailings storage facility and quarry is collected and neutralised prior to discharge into the creek. Tailings have been covered with waste rock, biosolids, neutralisation sludge and soil and planted with grasses, shrubs and trees to reduce rainfall infiltration. Monitoring of water flows, water quality and riparian ecosystems is on-going. Consultants have been engaged to develop cost-effective remediation techniques and a five-member Brukunga Mine Site Remediation Board was appointed to oversee remediation of the site and liaise with the community. Construction has commenced on the diversion of Dawesley Creek, and plans are being developed for the relocation of waste rock back to the quarry benches and upgrading of the neutralisation plant. The paper examines operations, environmental monitoring, remediation, research and community involvement with respect to current best practice.

Jan 1, 2003

By Jansen N

Production from the narrow, high grade silver-lead-zinc orebodies below 15 level commenced in mid 1985.Geological, mining research and recent mining experience determined that a mechanised drill, fire and muck cycle would be the most suitable method.Ground conditions are predicted to be worse than in other cut and fill (MICAF) areas at Isa Mine, owing to the increased depth, more variable dip of the orebodies and the increased effect of major geological structures.Mechanised ground support and tight filling techniques feature in controlling these expected adverse ground conditions.

Jan 1, 1985

By D Tucker, K Harney

Hatch forecasts that an increasing share of seaborne traded iron ore will be ultrafine, being either concentrate or pellet feed. This provides several challenges for the iron and steel industries, but the principal concern is: how much ultrafine iron ore can be consumed on sinter strands and with a minimal effect on productivity?This paper will identify new supply by project through 2020. Demand will be estimated for sinter production and practical steps will be identified to increase ultrafine consumption in sinter strands. The long-term iron ore price will be forecast to balance supply and demand. The paper will conclude by assessing how the pricing of ultrafine ore will develop relative to the Chinese iron ore indices.CITATION:Tucker, D and Harney, K, 2015. Iron ore ultrafines challenges and opportunities, in Proceedings Iron Ore 2015, pp 501–504 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and cesting campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and altei._acive, cheaper, additives for cementing hydraulic Fill.

Jan 1, 1980

By I T. Ross

In the last 50 years there have been tremendous improvements in equipment used in development on underground mines. Compressed air powered jacklegs have been replaced by high powered electro-hydraulic drifters on sophisticated drill jumbos and load haul dump units have taken over from small shovels and rail cars.Despite the increase in power applied in key parts of the development cycle, average advance rates have fallen and costs have increased. The factor that is most often regarded as the main contributor to slowing advance rates is increased support requirements. Whilst there is no denying that the drive to improve safety has resulted in the requirement for more bolting and the installation of a skin support (mesh or shotcrete), this is not the only factor.Within the industry as a whole, many of the basic principles of development appear to have been lost over time. This paper looks at a historical case study and discusses some of the features of old development cycles that are no longer in use. This highlights some of the basics that appear to have been forgotten. These may be indicators to what may provide improvements in the conventional drill and blast development cycle.CITATION:Ross, I T, 2014. Development – back to basics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 67–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Hartley JS, Wills KJA

The Thalanga massive sulphide deposit is hosted by Upper Cambrian rhyolites and volcaniclastics of the Mt. Windsor Volcanics near their contact with overlying dacites, rhyolites and sediments of the Trooper Creek Formation. The ores and host rocks have been subjected to a single strong deformation and to lower to middle greenschist facies metamorphism. A main lens with surface gossan dimensions of 55U m x 6 m dips steeply, plunges shallowly to the west and is offset by a series of normal faults. It is flanked by smaller lenses to the east where the mineralized horizon is stopea out by granite. The area to the east and south of the gossan is masked by Tertiary cover. A complex exhalite package is represented by banded sphalerite-pyrite- galena-chalcopyrite, massive pyrite and chalcopyrite and assemblages dominated by dolomite, chlorite-actinolite, tremolite, talc, barite and rare gypsum. Accessory tetrahedrite, arsenopyrite, bismuthinite, magnetite and native gold are associated locally. Pods of quartz-magnetite formed distally. The ores are underlain by strongly to moderately pyrite-silica-sericite altered rhyolites with the strongest alteration closest to an interred synvolcanic fault. This alteration is characterised by an enrichment in MgO, Na2O, FeS2 and base metals with a depletion in CaO and Na2O. There is a general enrichment in Pb and Zn towards the hanging wall with some enrichment of Cu near the base of the main lens due to replacement by ore tiuias near vent discharge sites. Zonation of Cu to 2n-Pb in also evident over narrow intervals

Jan 1, 1987

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Jarvensivu M, Ylinen R, Jamsa-Jounela S-L

The paper presents a new integrated system for control of concentration processes. The system is based on cluster-based modelling taking the ore quality into account and a new on-line particle size analyser capable also for reliable measuring of particle size distribution of concentrate. A metallurgical precontrol audit was performed at the Hitura concentrator in order to design the control strategy of the integrated grinding and flotation control. A new analyser PSI-200, was used to the measurement and control of the distribution of nickel in the total particle size range. An expert control system using the cluster model together with a new control strategy for decision of necessary control actions is outlined. The method has been tested to real data from mineral processes. The results are in good correspondence with empirical process knowledge. KEYWORDS: Cluster analysis, expert control, flotation control, mineral processes, modelling, particle size.

Jan 1, 1993

By D Drinkwater

In 2009, Peter Munro and Peter Tilyard examined the “human capital” in the mineral processing sector in a paper entitled Back to the Future (Munro and Tilyard, 2009). One of their major concerns was a general decline in technical skills and process knowledge, exacerbated by lack of appreciation of the impact this can have on process plant performance and, ultimately, profitability or sustainability of the industry. There are many reasons for this decline, not least of which are the work schedules of today’s metallurgists which have a very different balance between technical and non-technical responsibility than those in the past. However, a shift towards a more technical focus has potential to deliver a range of benefits for industry at large and for the individuals in it This paper discusses some options for development of core metallurgical and process engineering skills that can be used by graduates, employers and training providers.Key skills are identified and mapped against available opportunities for development, such as existing graduate programs, on-the job training and external courses. The authors also review a number of past and present high-quality graduate development programs, including the graduate development program in place at Mount Isa Mines in the 1980s and the Anglo Platinum Graduate Development Program (AGDP) currently operating in South Africa.

Aug 8, 2011

By Glassock C. D

Most Australian mining projects are becoming smaller, more remote and with lower grades of ore. Their small size has been making it harder for mining companies to absorb the large infrastructure costs. This has forced companies to reduce those costs in every way they can. Social factors, environmental groups and even tax laws have added other pressures to force down the infrastructure costs for remote projects. For the last ten years, the downward trend in costs has been marked. It seems certain to continue for years into the Future.

Jan 1, 1997

By Whitworth N, Anderson P

New plant has been commissioned to treat off-gases from the Fluo-solids Reactor in the Copper Smelter. The new section of plant was built onto an operating system and commissioned with minimum disruption to production. Under construction is a 270 m tall stack for Lead Smelter gases. Additional items for the Lead Smelter will include a new gas cooler, a central baghouse to replace Sinter Plant wet gas scrubbers, a new exhaust fan on the main baghouse, and ducting of drossing gases to the main baghouse. Emphasis is given to discussing improvements the new plant has made to working conditions, the general environment and increased production capability. Total expenditure in the two smelters is in the order of $25 million.

Jan 1, 1978

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By S Gillies, H W. Wu

A study has been undertaken into mine ventilation systems currently in use within Australian modern coal longwall (LW) extraction mines. It reviews systems and discusses evolving changes being adopted to address the more complex challenges. There is a strong move to longer panels, wider faces, greater extraction heights, increased production rates, more efficient ventilation and decreased personnel. Each of these changes is motivated by improvement in productivity and generally leads to cost reduction. In addition, mine workings are moving deeper, which results in increased ventilation control issues such as higher total and respirable dust levels, greater seam gas contents in parallel with lower in situ permeabilities, spontaneous combustion and heat management issues. A comprehensive database of Australian LW ventilation practice is analysed. Currently there are a variety of LW panel ventilation circuits used in Australian underground coal mines due to various combinations of seam characteristics, gas emission rates, spontaneous combustion, geological features and surface constraints. The main issues usually addressed in the designing and planning of ventilation circuits for LW panels are airway velocity, gas concentrations, LW cutting methods (eg Bi-di, Uni-di or half web), ventilation of control devices, pressure differentials and leakage paths and understanding gas concentrations across the length and width of the goaf. If the ventilation circuit can manage the applied contaminant load (gases, heat and dust) at an acceptable cost and circuit duty, then supplementary controls, such as gas drainage, refrigeration and dust sprays and scrubbers, may not be required. CITATION:Gillies, S and Wu, H W, 2013. Review of Australian longwall panel ventilation practices, in Proceedings The Australian Mine Ventilation Conference , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Rowena C. Duckworth

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP. Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, ODP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the ODP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

The object of this paper is to give an insight into various metallurgical operations involved in the making and shaping of steel for shipbuilding at the Newcastle plants of the Broken Hill Proprietary Co. Ltd., Commonwealth Steel Co. Ltd. and the Port Kembla plant of Australian Iron and Steel Ltd. Whilst not steelmakers, inasmuch as their processes start with semi-finished. steel supplied by the Steelmaker, the plants of Stewarts and Lloyds (Aust.) Pty. Ltd. and their associate company, British Tube Mills, Rylands Bros. (Aust.) Pty. Ltd. and the Newcastle and Kembla plants of John Lysaghts (Aust.) Pty. Ltd. make substantial contributions to the Australian shipbuilding industry, principally by way of boiler tubing and wires for welding rods and sheet steel, including special silicon lamination sheet for electrical motors.THE MAKING OF STEELThe making of iron and steel began as an accident, slowly developed as an art and has not yet become an exact science. The iron age dawned on the day when, by chance, man's primitive ancestor built up the wall of his fire with ironstone. In the ashes of the fire he found pieces of sponge iron from which he hammered out the first sample' of wrought iron. For many centuries iron ·was manufactured in bloomeries and occasionally, when the temperature was excessive, the iron combined with some carbon and steel was produced. But it was not till '1740 that steel was manufactured under controlled conditions. In that year Huntsman invented the crucible process which held undisputed sway for over a 100 years until in 1856 the invention of the Bessemer process revolutionised the whole industry.From then on, rapid progress was made. The Siemens...

Jan 1, 1951

By S S. Kanchibotla, I Brunton

Most blast fragmentation models assume the rock mass properties, explosive properties and blast design variables to be constants and uniformly distributed within a blast. However, in reality all these input variables vary within a blast resulting in variation in the resulting fragmentation size distribution. A stochastic modelling approach is introduced in this paper to quantify this variation. This technique takes the input variables as statistical distributions rather than constants and through several thousand iterations, generates a statistical representation of the expected fragmentation resulting from a production blast. A case study of three production blasts from a large open pit mine are presented and the modelled fragmentation æenvelopeÆ shows good agreement with the fragmentation æenvelopeÆ estimated from Split image analysis. The various blast-related parameters influence different parts of the fragmentation distribution, eg rock strength and explosive velocity of detonation have most impact on the fines. The technique is used to identify the parameters that have the greatest influence on various size fractions. Such an analysis will be useful to direct resources to efficiently minimise the variation.

Jan 1, 2001

By S C. Dominy, R C. A Minnitt

Determination of the sampling constant and liberation diameter are of importance when applying the Fundamental Sampling Error (FSE) equation to optimise sampling protocols. The method for the direct determination of the sampling constant is based on the æGy 50-pieceÆ experiment and variants thereof, which is generally known as the heterogeneity test. In the coarse gold environment, the heterogeneity test is prone to poor repeatability and bias due to the very heterogeneity that it aims to quantify. A key issue is the large sample mass that can be required in the coarse gold environment, which may reach 1 t or more. The heterogeneity test often provides an evaluation of the background gold grade heterogeneity, but understates that of the high-grade coarse-gold component. This is because the total mass of fragments is usually too small to represent the mineralisation. Despite this relatively well-known problem, heterogeneity tests are often undertaken on deposits where the presence of coarse gold is ignored, not fully realised or vastly understated. Sampling types and protocol designs are frequently based on poor quality data that do not match the characteristics of the orebody. For this style of mineralisation, an empirical approach to define ore characteristics is recommended.CITATION:Dominy, S C and Minnitt, R C A, 2012. Application of heterogeneity testing to coarse gold ores, in Proceedings Sampling 2012 , pp 143-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

INDEX OF CONTENTSBlast Furnace SlagsForehearth AccretionsConverter SlagsConclusionsIllustrationsCOMPOSITION OF SOME COPPER SLAGS FROM PORT KEMBLASamples of copper slags from the Port Kembla Smelter of the Electrolytic Refining and Smelting Co. of Australia, Pty. Ltd., have been submitted for mineragraphic examination, with reference to the mode of occurrence of copper in them. The samples included (I) blast furnace slags, (H) a forehearth accretion, and (IH) converter slags. 1. BLAST FURNACE SLAGS Four series of samples of blast furnace slag have been submitted. The. chemical compositions of the several slags are shown in Table 1. Analyses Nos. 1 and 2 are of samples of slowly or normally cooled slag, taken from the slag dump, Analyses Nos. 3 and 4 are of samples comprising slowly or normally cooled slag, together with granulated slag from the same melt.

Jan 1, 1949

By J Seccatore, G Sadao, M Cardu, G De Tomi, L Finoti, F Galvão, J Romero Huerta, A Rezende, J Bettencourt

In the mining industry, rock blasting can be considered as the first phase of comminution. The downstream phases of comminution are mechanical, and consist in consecutive stages of crushing and milling for grain size reduction. The total energy of mechanical comminution depends on grain size and on the resistance of the material to grindability. Usually, the first is quantified by the grain size distribution or one of its KPIs (such as the diameters X50 or X80), while the latter by the working index (WI), representing the amount of energy necessary to reduce the size of grains of a determined amount of material to the desired equivalent diameter (usually expressed in kilowatt hours per tonne – kWh/t). It is widely recognised that it is possible to manage the output of a blast in terms of grain size distribution varying specific charge (powder factor – PF) and charge distribution; specific algorithms such as the KUZ-RAM or the SWEBREC have been created to predict such output. It has also been demonstrated how higher PFs weaken the blasted material by creating micro-fractures that reduce its WI. This paper focuses on a related aspect: the influence of charge distribution on the specific comminution energy in crushing and milling. Small-scale blasts have been performed on 14 marble blocks with different PFs and charge distribution. For every PF, charges have been designed to simulate concentrated and distributed geometries. Concentrated charges simulate opencast blasts with large-diameter holes, with large burdens and spacings. Distributed charges simulate bench blasts with small-diameter holes and reduced burden and spacing. Three control blocks have been fragmented by mechanical means for comparison. For every sample the grain size distribution and the WI in ball mill has been determined. Results show the correlations between charge distributions and the specific energy of mechanical comminution in milling. Finally, the opportunity of adjusting charge diameters and distributions in opencast blasts to improve the output of the comminution circuits is discussed.CITATION:Seccatore, J, Romero Huerta, J, Sadao, G, Cardu, M, Galvão, F, Finoti, L, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The influence of charge distribution on the grindability of the blasted material, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 749–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Koshy, M Ralph, P Foley

Mining in the state of Western Australia (WA) formally commenced in the 1840s, and over the ensuing 180 years has evolved to be the epicentre of the Australian mining industry and a significant contributor to the national economy. The lithology of WA is replete with mineralisation that hosts uranium and ‘critical minerals’ required for the global renewable energy sector. The state’s first uranium mine is under development, and high levels of activity are occurring in the state’s nascent critical minerals sector, with 168 WA-based companies pursuing rare earth-bearing minerals, 51 of which are actively drilling on their tenements. WA’s mineral deposits typically contain levels of the naturally occurring radionuclides (NORs) thorium-232 and uranium-238 that are elevated above the global crustal average. Workers are exposed to NORs during the mining and mineral extraction processes, and radiation doses that exceed applicable exposure standards may eventuate. The research traces the history of worker radiation doses from 1977 to 2020, finding the maximum dose was 163.4 mSv, more than eight times the current derived annual dose limit. Whilst 93.5 per cent of all workers received doses of less than 5.0 mSv per annum, the potential for elevated doses is ever-present as witnessed by 10.3 mSv reported in 2009/2010. The increase in activity coincides with a revision of the dose coefficients (DCs) associated with the intake of radionuclides. The research evaluates the revised DCs and forecasts doses from inhalation of radioactive dusts will nearly double, and lead to workers receiving doses exceeding 5 mSv for the first time since 2009/2010. The research finds that the current regulatory framework is fit-for-purpose. However, inter-agency relationships, and the capacity of the regulator to effectively regulate the current and future number of mining operations is questioned. The mining industry is vulnerable to capability and capacity constraints – but has failed to respond to issues in relation to competent radiation safety officers first raised by the Winn Inquiry (Winn, Mathews and Tough, 1984). Disconcertingly, monitoring of worker exposures to NORs reached a nadir in 2021, raising questions as to the veracity of worker doses reported to the regulatory agency. The research recommends personal dust sampling be prioritised.

Apr 16, 2024