Search Documents

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By T. Smales, P. L. Wright, K. Barron

The results of field measurements using an air injection technique to investigate the integrity of three pillars in the Mclntyre Mines Ltd. 114 seam at Crande Cache, Alberta, are reported. These pillars are shown to be stable and an estimate is made of the strength of these pillars. Using these results, together with Hustrulid's pillar strength formulae, a general pillar strength equation for the 114 seam is developed. This equation takes into account the probability of failure that may be deemed tolerable within the design requirements. The variation of the minimum pillar dimensions with depth below surface for uniform pillar layouts is then examined for a range of tolerable failure probabilities. A general equation of the form B = 2.60 +B Z relates the minimum pillar design width, B metres, with the overburden depth, Z metres, where B is a parameter related to the tolerable failure probability. This equation only applies for 3.05m high pillars with 6.lm wide entries. Finally, the question of what failure probability is tolerable within the design of mine pillars is discussed. This will depend on the support role required of that pillar and the anticipated period over which the pillar must perform that role. Five categories of coal mine pillars are defined, each with a somewhat different role to perform. Tentative design criteria in the form of "tolerable probabilities of failure" are suggested for four of these five categories of pillar. The fifth category of pillar has no reliable support function to perform and support must be obtained by other means.

Jan 1, 1983

By R. W. Nelson

The theoretical basis is presented for energy dissipation methods of measuring permeability in saturated heterogeneous media. Analysis starts with the equation for single-phase flow in heterogeneous porous media which is a first-order partial differential equation in the unknown permeability. This equation is reduced to a system of characteristic equations useful in deriving a differential expression for the permeability as a function of the known potential distribution. For steady flow systems the expression is integrable, giving the permeability integral for direct calculation of the distribution along successive streamlines. The boundary condition in permeability is presented and includes a discussion of the special requirement to assure uniqueness. Theoretical results and necessary computations are incorporated into two general computer programs capable of determining the permeability distribution in two- and three-dimensional steady flow systems. Results are then presented for an energy dissipation analysis using the methods and soltware to determine a field permeability thickness distribution. INTRODUCTION Theoretical work leading to the description of fluid flow in heterogeneous porous media has developed slowly and somewhat sporadically, although the areas of engineering applications predominantly involve flow in nonhomogeneous media. The lack of accurate and economical methods for measuring field permeability distributions has been a major limitation to realistic description of natural flow systems. The economical measurement of permeability using energy dissipation methods may overcome this limitation. Among other things, any permeability measurement method involves consideration of energy dissipation; as used here, "energy dissipation method" denotes the following general approach. The areal energy distribution is measured on an existing flow system in porous media. Then through appropriate analysis of the dissipation of energy in the flow system, the permeability distribution is determined throughout the region using the minimum boundary conditions required to assure a mathematically unique result. This paper presents the theoretical basis for such a method, as well as the techniques and computer software needed to carry out the analysis. The method and techniques are then used in a preliminary field application. EQUATIONS DESCRIBING FLOW IN HETEROGENEOUS MEDLA Heterogeneous as used here implies differing in kind, having unlike quantities or possessing different characteristics. Accordingly, a heterogeneous porous medium has unlike quantities or differing characteristics at different locations. More precisely, if a porous medium is heterogeneous with respect to some property, then that property is functionally dependent on the spatial location. (Media properties are considered here as macroscopic.) Specifically considering permeability k,** then k = G(x, y, z) ,............(1) or the permeability is a scalar function G of the location (x, y, z). Spatial variation of several other properties, of which porosity, dispersivity and medium compressibility are but a few, is implied by the broad title of heterogeneous porous media. The term will be used hereafter to imply only heterogeneity with respect to permeability. The porous medium is considered isotropic as implied by G being only a scalar function. Anisotropy

Jan 1, 1969

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By E. L. Dougherty, J. W. Sheldon

A numerical method for computing the dynamical behavior of fluid- fluid interfaces is described. Results of studies made to assess the accuracy and economy of the method on a computer are reported. It is concluded that it is practical to obtain digital computer solutions for fluid- fluid interface problems with two space dimensions. PROBLEM DEFINITION We consider two-dimensional flow in a rectangle as shown in Fig. 1, where a fluid-fluid interface divides the rectangle into two regions. The pressure is specified along the lower boundary (the injection boundary) and upper boundary (the withdrawal boundary). There is to be no flow of fluid across the side boundaries, which are walls of symmetry for the flow, and px = 0 along these boundaries. The fluids are incompressible, the absolute permeability and porosity is constant, and each fluid has its own constant mobility. Thus, the pressure satisfies Laplace's equation in each region. Across the interface, pressure is continuous and the normal component of fluid flux is 1. These conditions are shown in Fig. 1. The velocity of a point on the interface in the direction of the normal from Fluid 1 into Fluid 2 is U,/ Q, where Un is the normal component of volumetric flux at the point on the interface, i.e., For brevity, we call the problem defined above "Problem A". Problem A is a simple example of a dynamical fluid-fluid interface problem. However, the same numerical methods which we use to solve Problem A can be extended to the solution of a large number of fluid-fluid interface problems which are mathematical models for various oil recovery processes,l hence our interest in Problem A. We define the interface by prescribing the x, y coordinates of a finite set of points. These points are called "interface mesh points" and are illustrated by triangles or asterisks in the figures. Fig. 2 is a procedural (flow) chart displaying the main steps in the solution. We comment briefly on some of these steps in this section and then give further details in subsequent sections. For mobility ratio greater than one it is well known that Problem A is unstable.*2 Small amplitude,

Jan 1, 1965

By Charles H. White

+1HARVARD UNIVERSITY, CAMBRIDGE, MASS. The equipment of a laboratory in which students are to be trained for practical work in metallurgical chemistry presents many difficulties not encountered in the fitting up of a commercial or works laboratory. At an industrial plant the chemical work required usually demands the frequent repetition of a comparatively limited number of methods. In a steel-works laboratory, for instance, by far the larger part of the work consists in making determinations of the usual impurities found in iron and steel; at a smelter the great bulk of the work is confined to the analysis of ores, slags, mattes, and fuels, which involve the frequent application of perhaps not more than a dozen different methods. In a laboratory of this character, therefore, those operations most frequently applied may each have a certain section set apart and fitted permanently with such apparatus as best facilitates the carrying out of this one operation. The work of a commercial or custom laboratory is perhaps more varied than that of a works laboratory, but the couditions are similar in these respects, that there is usually no great need for economy of space, and that a few skilled workmen are employed to carry the determinations through from beginning to end without interruption. On the other hand, the laboratory of a technical school should be planned on such a scale that a comparatively large number of students may work at the same time, and each desk should be equipped for general metallurgical analysis. In most institutions for technical education the student's program is so arranged that his day is divided among several subjects in the course of study; only a few consecutive hours being devoted to one subject, or spent in one laboratory. Therefore, those appliances should be provided that render possible the safe continuation of such processes as

Jan 1, 1905

By E. J. Hall

(Butte Meeting, August, 1913.) THE iron-nail method of assaying has been used for a number of years, but has not met with the approval of all assayers. The method possesses advantages which may be given as follows : (1) no preliminary treatment is required ; (2) a lead button of proper size can be obtained (3) it is economical. On, the other hand, it has its disadvantages, which may be summed up as follows: (1) it is not applicable to ores containing large amounts of impurities other than sulphur, as practically all the base metals will contaminate the lead button ; (2) the slag is unsatisfactory in the larger number of fusions; (3) the method was known to give low silver results under certain conditions and the gold results were questionable. It was with the idea of determining the extent of this latter disadvantage that the following investigation was undertaken. It is well known that the fusion obtained in the lend assay is far more satisfactory than that in the " nails method " for gold and silver. The principal difference in the charges as a class is the presence of considerable reducing agent in the lead charge, and a limited oxidizing action in the nails charge, due to PbO. The possibility of improving the nails fusion by simulating the lead charge was the reason for using argol in some tests, even though there were reasons for expecting this would have -au objectionable effect on the results.

Jan 6, 1913

By P. St. J. Perrott

AN explosive of balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypoth¬esis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By I. Fatt, D. N. Saraf

A method is described for measuring two- and three-phase relative permeabilities in sandstones or sand packs using a nuclear magnetic resonance (NMR) technique to determine fluid saturations. Two- and three-phase relative permeabilities have been determined on Boise sandstone using the NMR technique of saturation measurement. Three-phase relative permeability to water was found to depend only on the water saturation, whereas three-phase permeability to oil depended on both the water and oil saturations. Relative permeability to gas in three-phase flow was found to depend only on the total liquid saturation. INTRODUCTION Three-phase relative permeabilities are extremely useful in calculating field performance for reservoirs being produced by simultaneous water and gas drives. Three-phase relative permeability data are also needed for analyzing solution gas-drive reservoirs which are partially depleted and are being produced by water drive. Some thermal recovery processes involve three-phase flow which require three-phase relative permeability data for predicting reservoir behavior. Unfortunately, three-phase relative permeability measurements have rarely been made. Also, because of the scarcity of three-phase data, it has not been possible to date to relate other measured rock characteristics to the relative permeabilities with a great certainty. Leverett and Lewis,l Reid2 and Snell3 have reported three-phase relative permeability data on unconsolidated sands. Leverett and Lewis used ring electrodes spaced along the length of the sand sample to measure the resistivity of the sample which was assumed to be monotonically related to brine saturation. Gas saturation was determined from pressure-volume measurements. Oil saturation was obtained by material balance on the cell containing the sand sample. This method is involved and time consuming. Another difficulty arises from the fact that the resistivity of the sand is a function not only of saturation of brine but also of the distribution and saturation history of the brine in the pore spaces. Reid2 used a gamma ray absorption technique for measuring liquid saturation. This method has the disadvantage that total liquid saturation rather than oil or brine saturation is all that can be measured and still another method is required to determine the saturations of individual components. snel13 used a neutron bombardment method which also required a separate determination of the individual component saturations. Caudle et al.4 measured three-phase relative permeability on consolidated sandstones using vacuum distillation for determining fluid saturations. Distillation after each reading makes this technique very lengthy and time consuming. Corey et a1. 5 and Naar and Wygal 6 measured three-phase relative permeability on sandstones by the capillary-pressure method. Semipermeable diaphragm assemblies were used at each end of the core specimen to keep the water phase in the core. Gravimetric methods were used to determine fluid saturations. Sarem7 recently reported an unsteady-state method for measuring three-phase relative permeability on sandstones. This method is an extension of Welge's method8 for measuring two-phase relative permeability. Although Sarem's method is simple and comparatively fast, the assumptions involved may oversimplify the problem. Sarem's assumption, that in all rocks relative permeability to each fluid will depend only on the saturation of that fluid, seems to be rather unrealistic. Neglecting capillary effects at the end of the core is also a weak assumption. Donaldson and dean9 measured three-phase relative permeability using a method similar to Sarem's.

By D. W. Fuerstenau, G. D. Gumtz

Use of the discretized batch-grinding model for the simulation of locked-cycle grinding tests from batch-grinding data is illustrated. The simulated results were compared with actual locked-cycle experimental data for the dry grinding of dolomite. To illustrate the utility of this simulation method, a number of relationships between operating and performance parameters were generated, including relations between batch grinding and the Bond test, the production rate and the circulating load, and the production rate and the product size. A large amount of testing is done each year in the mineral industry for use with grinding unit cperations, and much of the experimental test data is obtained by the tedious locked-cycle testing procedure. In addition to being experimentally complex and requiring large amounts of sample, the very nature of the locked-cycle experiment yields results that cannot readily be interpreted. The attempts that have been made to model comminution systems during the last few years may provide a better and simpler way to obtain and analyze grinding test data; these models involve elements of both fitting to "model equations" and deterministic representations.1-1 The traditional engineering design techniques for comminution systems have relied mainly upon large amounts of industrial operating data that have been correlated with locked-cycle grinding data.',' Bond's empirical mill-design procedure involving locked cycle testing remains the most generally available method to this day. The purpose of the present paper is to show how much more useful data can be obtained from a simple batch-grinding experiment that provides information which subsequently can be utilized with population balance models of the grinding process to simulate locked-cycle behavior. These simulation results can, of course, be used in Bond's general design scheme. However, the combination of batch-grinding tests and the population balance model allows many more conditions to be considered than do single laboratory tests under specific locked-cycle conditions. The use of these simulation techniques for prediction of locked-cycle behavior represents one of the first practical applications for the simulation method in comminution.

Jan 1, 1971

By K. E. Beu

THE integrated intensity X-ray method of meas-uring retained austenite concentrations in hardened plain carbon or low alloy steels as proposed by Averbach and Cohen1,2 has the advantages of being a highly sensitive and precise quantitative method. The various phases of this method have been studied and several modifications have been developed which aid not only in reducing the time required per determination, but which also increase the possible accuracy of the method. A fundamental step in the original calculation procedure is to plot V.A(?) curves for austenite and martensite and to obtain VM/VA ratios from these curves.' In taking this ratio the absorption factor A (8) drops out since it is constant for a. given diffraction angle 8. The reason for eliminating A(?) in this manner is because it is apparently assumed

Jan 1, 1953

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

A simple and inexpensive mercury-tracer method has been develohed to study rates and Patterns of gas flow in blast furnaces. A Pulse of mercury is injected into the hot blast, and its arrival at the sampling Point is recorded by an electronic circuit that measures resonant absorbtion of ultraviolet light by mercury vapor in the gas aspirated .through the detecting. cell. A rapidly developing interest in blast-furnace technology in recent years has created a strong demand for precise knowledge of the rates and patterns of gas movement through the stock column. Classical fluid-flow theory cannot supply the desired information because the complexity of the blast-furnace situation precludes the accurate determination of many of the parameters required for solution of the equations. In fact some of the terms employed in fluid-flow treatments become almost meaningless under blast-furnace conditions. The void fraction of the stock column, for example, varies widely from place to place and is affected by the segregation of charge materials, attrition of lumps during descent, and channeling. Gas density varies with changes in local pressure, temperature, and composition, while viscosity varies with temperature and composition. Even if mean values for these functions were acceptable, they would be either impossible or extremely difficult to determine with a high degree of accuracy since the value of the mean for all gas properties would depend upon the flow distribution itself. Attempts to study gas movement by the pitot-tube determination of kinetic pressures have met with little acceptance. Reproducibility of results is extremely difficult to achieve in a situation where alignment of the tube orifice with respect to the flow direction in tortuous channels cannot be guaranteed. Because of these difficulties it would appear that progress can be achieved only with a direct method of measuring gas velocities and determining the shape of flow paths through the stock. The establishment of such a method is described in this paper. SELECTION OF METHOD Direct measurement suggests the use of a tracer by means of which the progress of a "parcel" of gas can be followed through the furnace. Several requirements must be met before any selected material can be considered a suitable tracer. First of all, it must be a substance not normally present in blastfurnace gas or dust; otherwise its presence in a gas sample will have little significance. It should be volatile at temperatures normally existing within the furnace, to ensure that it will travel with the gas, as a gas. It should possess special properties enabling its presence in the gas to be detected readily, and it should not undergo exchange reactions with any material normally present within the furnace, including refractories and coke as well as all components of the metal and slag. Radioactive materials naturally are considered because their radioactivity renders them susceptible to detection. However, of the many radioactive materials available, almost all are eliminated from final consideration by their unsuitability in terms of other properties. Radioactive silicon, carbon, calcium, phosphorus, and many others have been considered and discarded, either because they are not volatile over the whole range of significant temperatures, or because they could be expected to undergo exchange reactions with burden or refractory materials. Others which might be suitable in terms of these properties are eliminated because of a low activity, short half life, or the necessity for fragile counting apparatus. Of the many elements available in radioactive form, perhaps radon is the only one suitable for blast-furnace gas-flow studies. This has been used in several investigations1-4 with considerable success. The use of radiotracers has certain inherent disadvantages. One is the cost. An appreciable sum must be allowed for materials each time a test is made. Also, special methods of handling must be employed, and very often the progress of an investigation must be governed by the availability of isotopes and the delivery arrangements that can be made for them. An advantage is immediately gained if the tracer material can be a substance which can

Jan 1, 1960

By S. Stutz

Coal, like most other minerals, only exceptionally occurs in a sufficiently pare state to he directly available for general manufacturing purposes. And even where this is the case, the small coal or slack is usually more impure than the lump coal, as the slate, clay, etc., from the roof and bottom of the vein become mixed with it in the handling it undergoes. These impurities often exceed ten or more per cent. in addition to the impurities of the coal itself. The most common impurities of the coal are slate, or shale, clay, and sulphur. The latter occurs in different forms, but moat frequently as bisulphide of iron, or iron pyrites, and as sulphate of lime, or gypum. In both cases the impnrities add greatly to the amount of ash, and where they are present in considerable quantities the raw coal, and still more the coke made from it, is unfit for the manufacture of iron. Coke will coutain on an average at least fifty per cent. more ash and sulphur than the ram coal from which it is made. To the manufacturer of iron every additional per cent. of ash which his coal or coke contains is a source of additional expense, seemingly small, and yet very important in the aggregate. In the blast-furnace, for instance, the ash must be heated up to the melting-point, and, since it is composed largely of refractory substances, the consumption of carbon in melting it will be equal to at least one-half of its weight; that is, a certain part of tile coke is consumed for the melting and fluxing of the ash and is lost. Besides this, it is well enough known to the iron-master that coke containing lees ash makes the &lag or cinder more liquid and less incliner1 to stick to the walls of the furnace. Fuel containing much sulphur produces generally a white iron, poor in carbon, while from the same ore arrd flux, with a pure fuel, a good foundry iron might be obtained. The work of separating slate, sulphur, etd, from the coal has as yet only been successfully accomplished by the washing process. This process depends for its success on the differences in the specific

Jan 1, 1881

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

By G. Carman Ridland

IN conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Müller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at. Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties.

Jan 1, 1944

By H. H. Evinger, M. Muskat

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By M. Muskat, H. H. Evinger

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.' Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By L. F. Mondolfo, B. E. Sundquist

The crystallographic orientation relationships resulting when lead is nucleated from the liquid by Ni, Cu, Ag, and Ge were determined. For each nucleating agent several definite orientatioz relationships were found. These relationships seemed to be controlled by good symmetry relations and low crystallographic disregistry between mating planes. For any given nucleating agent the under colling for nucleation was found fairly constant and independent of the orientation relationship and consequent disregistry. It was also found that, upon re melting and refreezing the Pb, the orientation relationship was changed. These findings prove that crystallographic disregistry is not the controlling factor in heterogeneous nucleation from the liquid. The results of this investigation tend to confirm the theory presented in a preceding paper that heterogeneous nucleation starts with the formation of an adsorbed layer of nucleated metal on the nucleat-ing impurity. Evidence is given that cavities in the nucleating agent act as centers of nucleation. IT has long been known' that solid extraneous particles are active in catalyzing phase transformations that occur in a system, particularly condensation and crystallization. It is well established that these heterogeneities act as catalysts by providing surfaces upon which nuclei of the precipitating phase can form with activation energies smaller than those required for homogeneous nucleation. Numerous investigations have shown that in this process of heterogeneous nucleation: a) the nucleus forms with one, or several, definite crystallographic orientation relationships with the nucleating phase2-4 and b) that there is a small range of undercoolings or super saturations characteristic of the nucleation of a given solid on a given Substrate.5-10 Turnbull and vonnegut11 have developed a theory based on theories developed by Volmer12 and Turn-bull and Fisher1= for heterogeneous nucleation from gases and liquids, that relates the super saturation or undercooling required for nucleation to the dis-registry between the lattices of the nucleus and the nucleating agent. This theory predicts that nucleation should occur with the orientation relationship between the nucleus and nucleating agent that minimizes the disregistry. Further, it predicts that the undercooling or super saturation necessary for nucleation should be a function of the disregistry. Numerous investigations have dealt with the orientation relationships resulting from the condensation of vapors onto crystalline solid substrates2,3 and a few with the nucleation of one phase by a second phase in solidification4,14. Others have dealt with the supersaturation8-10 and undercooling5-7 associated with nucleation in condensation and solidification respectively. However, there is virtually no report that gives both of these factors for the same system. In this investigation a study was made of the undercoolings and orientation relationships resulting when Pb is nucleated from the liquid by Ni, Cu, Ag, and Ge. It was the purpose of this investigation to check the Turnbull-Vonnegut theory, i.e., the importance of crystallographic disregistry between nucleating catalyst and nucleated metal. The results indicate that disregistry is not an important factor in nucleation and that the nucleation process is probably somewhat more complex than current theories suggest. EXPERMENTAL PROCEDURE Small single crystals of nickel, copper, silver, and germanium were prepared from materials of four to five nines purity, and the Pb used was also 99.999+ pet pure. Cu and Ag single crystals were prepared by sealing small chips of Cu or Ag in an evacuated quartz capsule and heating the capsule at 2000°F for 1 hr before cooling. Nickel crystals of 200 diam were also prepared in evacuated quartz capsules, but melting was done by heating the capsules in an oxy-acetylene flame for a few minutes. These spheres were invariably polycrystalline so

Jan 1, 1962