Search Documents

By D. C. Porterfield

-4s a result of world economic conditions brought about by the European war and the consequent loss of European markets for Venezuelan crude, production in Venezuela decreased from 205,433,000 bbl. in 1939 to 186,134,000 bbl. in 1940, or 9.4 per cent. This decline interrupted a steady annual increase in production from the country, which had been continuous since 1932. The Maracaibo Lake Basin in western Venezuela accounted for 135,738,000 bbl. during 1940, or 73 per cent of the total, as against eastern Venezuela's production of 50,396,000 bbl., or 27 per cent of the total for the country. Corresponding figures for 1939 were 167,688,000 bbl., or 82 per cent of the total from the Lake Basin, and 37,744,000 bbl., or 18 per cent from the east. These comparisons indicate the increasing importance of the newer developments in eastern Venezuela, but it is unlikely that production from the east will ever exceed that from the west. In all, 429 new wells were completed in Venezuela during 1940 as compared to 438 in 1939. Of the 1940 completions, 411 were in proved areas and 18 were wildcats; 389 (95 per cent) of the exploitation wells drilled were producers, I was a gas well and 21 were dry holes, while 6 (33 per cent) of the wildcats drilled were producers and 12 (67 per cent) were dry; 263 of the exploitation wells and 4 of the wildcats were in the Maracaibo Lake Basin and 148 exploitation wells and 14 wildcats were in the east, mostly in the State of Anzoategui. Exploration of the light-oil areas in the Tia Juana and Lagunillas fields was con- tinued during the year with favorable results. Along the lake shore, drilling was confined principally to fill-in wells in the La Kosa, Tia Juana, Laguni!las and Bachaquero fields, although some important semi-exploratory drilling was done in the Pueblo Viejo area between Lagunillas and Bachaquero fields. The only other developments of particular interest in the west were the successful completion of a step-out well lying to the south of the former southern limit of Mene Grande field, which adds considerable proved acreage to that field; and the failure of two wildcats that were drilled near the Colombian border to determine whether the productive sands of the Petrolea field in the Barco Concession, Colombia, extend into Venezuelan territory. In the east no new fields were discovered during the year, although five wildcats were completed as producers. Three of these, Guario No. I, Jusepin-56 and LM-I (Leona), discovered important extensions to previously proved areas and the remaining two, Cantos-I and SPN-I (Socororo), were subsequently proved to have tapped productive sands of small extent and operations in these areas have been suspended. The greatest activity in the east was concentrated in the Oficina field, where 105 new wells were completed during the year and production was increased from 22,540 bbl. per day during January 1940 to 57,627 bbl. per day during December 1940. Important development work was also done in the Jusepin. San Joaquin and El Koble fields.

Jan 1, 1941

SAFETY in open-pit mining receives a minimum of notoriety, but its significance in profitable and efficient operation is as great as in other methods of mining. Open-pit operators from Arizona, New Mexico, and Mexico, exchanging ideas on safety at a symposium during the recent annual meeting of the Arizona Section, AIME, discovered unanimity of opinion that the successful safety program depended on managerial and supervisory support with the vigorous cooperation of the employes. Safety Organization The operation of a safety program is dependent on the ability of management to project enthusiasm through the company organization. This requires a suitable method of communication to the supervisory and employee levels so as to approach them in a manner that will inspire cooperation. Safety committees comprised of various combinations of managerial, supervisory, and employe personnel are frequently used for this purpose. The open-cut mine of the Chino Division of the Kennecott Copper Corp., Santa Rita, N. Mex., operates its program through management, a full-time safety engineer, and two safety committees, the Departmental and Shops Safety Committee and the Central Safety Committee. The Departmental and Shops Committee consists of one employe from each department and shop and the safety engineer. The selected members serve for a period of one month. This committee meets once a month, the only representative of management being the safety engineer because it is believed that employes will speak more freely when their supervisors are not present. The duties of the committee are to report hazardous conditions and make recommendations, but the committee has no authority to approve or disapprove. The Central Safety Committee is comprised of supervisory personnel from all departments and shops, and one member of each of the five bargaining organizations. Members of this committee are permanent and hold meetings soon after the departmental group to take action on recommendations of the latter. The committee system insures participation of all levels of personnel in the accident-prevention program, thereby stimulating safety consciousness. The New Cornelia branch of the Phelps-Dodge Corp., uses three groups to conduct the safety program; the General Safety Committee, Division Safety Committee, and the operating-unit safety meetings. The unit safety meetings provide for active participation of employes in discussion of various phases of the program. Within these groups vigorous opinions regarding safety are often expressed and the workmen are critical if they recognize a digression from the adopted safe-practice procedures. These monthly discussions give the program vitality. The Division Safety Committee is composed of the division superintendent and the division department heads, and follows an established pattern in discussion of all phases of the safety program. The General Safety Committee, made up of the manager, division, and department heads, makes decisions on policies and procedures; it renders decisions on recommendations and suggestions. Management at the New Cornelia branch feels this system of safety committees and meetings has been active in advancing the program. Safety Codes In the open-pit mines of the Southwest, a safety code for operation or service of equipment, methods

Jan 1, 1952

By D. C. Porterfield

-4s a result of world economic conditions brought about by the European war and the consequent loss of European markets for Venezuelan crude, production in Venezuela decreased from 205,433,000 bbl. in 1939 to 186,134,000 bbl. in 1940, or 9.4 per cent. This decline interrupted a steady annual increase in production from the country, which had been continuous since 1932. The Maracaibo Lake Basin in western Venezuela accounted for 135,738,000 bbl. during 1940, or 73 per cent of the total, as against eastern Venezuela's production of 50,396,000 bbl., or 27 per cent of the total for the country. Corresponding figures for 1939 were 167,688,000 bbl., or 82 per cent of the total from the Lake Basin, and 37,744,000 bbl., or 18 per cent from the east. These comparisons indicate the increasing importance of the newer developments in eastern Venezuela, but it is unlikely that production from the east will ever exceed that from the west. In all, 429 new wells were completed in Venezuela during 1940 as compared to 438 in 1939. Of the 1940 completions, 411 were in proved areas and 18 were wildcats; 389 (95 per cent) of the exploitation wells drilled were producers, I was a gas well and 21 were dry holes, while 6 (33 per cent) of the wildcats drilled were producers and 12 (67 per cent) were dry; 263 of the exploitation wells and 4 of the wildcats were in the Maracaibo Lake Basin and 148 exploitation wells and 14 wildcats were in the east, mostly in the State of Anzoategui. Exploration of the light-oil areas in the Tia Juana and Lagunillas fields was con- tinued during the year with favorable results. Along the lake shore, drilling was confined principally to fill-in wells in the La Kosa, Tia Juana, Laguni!las and Bachaquero fields, although some important semi-exploratory drilling was done in the Pueblo Viejo area between Lagunillas and Bachaquero fields. The only other developments of particular interest in the west were the successful completion of a step-out well lying to the south of the former southern limit of Mene Grande field, which adds considerable proved acreage to that field; and the failure of two wildcats that were drilled near the Colombian border to determine whether the productive sands of the Petrolea field in the Barco Concession, Colombia, extend into Venezuelan territory. In the east no new fields were discovered during the year, although five wildcats were completed as producers. Three of these, Guario No. I, Jusepin-56 and LM-I (Leona), discovered important extensions to previously proved areas and the remaining two, Cantos-I and SPN-I (Socororo), were subsequently proved to have tapped productive sands of small extent and operations in these areas have been suspended. The greatest activity in the east was concentrated in the Oficina field, where 105 new wells were completed during the year and production was increased from 22,540 bbl. per day during January 1940 to 57,627 bbl. per day during December 1940. Important development work was also done in the Jusepin. San Joaquin and El Koble fields.

Jan 1, 1941

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By William Kent

More than twelve years were spent by Wöhler at the instance of the Prussian Government in experimenting upon the resistance of iron and steel to repeated stresses. The results of his experiments are expressed in what is known as Wöhler's law, which is given in the following words in Du Bois's translation of Weyrauch:* " Rupture may be caused not only by a steady load which exceeds the carrying strength, but also by repeated applications of stresses, none of which are equal to the carrying strength. The differences of these stresses are measures of the disturbance of continuity, in so far as by their increase the minimum stress which is still necessary for rupture diminishes." A practical illustration of the meaning of the first portion of this law may be given thus: If 50,000 pounds once applied will just break a bar of iron or steel, a stress very much less than 50,000 pounds will break it if sufficiently often repeated. This is fully confirmed by the experiments of Fairbairn and Spangenberg, as well as by those of Wöhler; and, as is remarked by Weyrauch, it may be considered as a long-known result of common experience. It partially accounts for what Mr. Holley has called the " intrinsically ridiculous factor of safety of six." Another "long-known result of experience"—although this has not, as the writer believes, been investigated by scientific experimenters—is the fact that rupture may be caused by a succession of shocks or impacts, none of which alone would be sufficient to cause it. Wrought iron will crystallize by repeated blows in service and become weaker than cast iron. Iron axles, the piston-rods of steamhammers, and other pieces of metal subject to continuously repeated shocks invariably break after a certain length of service. They have a "life" which is limited. Iron rods in bridges sometimes crystallize and break, although the rods in most of our iron bridges

Jan 1, 1880

By E. M. Wise

The practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgrenl and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward12 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents15 and are becoming of commercial importance in the production of high-strength castings. The equilibrium relations existing in the high-copper region of the copper-nickel-tin system have been carefully studied by Eash and Upthegrove,6 and in somewhat less detail by Veszelka.7 The observa-

Jan 1, 1934

By W. A. Koehler, M. E. Hinkle

THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: 1. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of ferrous (iron) sulphate and some sulphuric acid. 2, The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages normally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio-6aciZZus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not Yet been established. Apparently it does not Promote the oxidation of ferrous iron compounds in mine drainage to the ferric state. The second organism has not been identified by name but is described as " Gram negative, non-spore-forming rods approximately 0.4 micron wide by 0.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur compounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced Percentage of Oxygen and increased percentage of carboll 'dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. Acid Coal Mine Drainage Acid coal mine drainage has been the concern of coal mine operators, industrialists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1949

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours' duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.' This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.' Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool' which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By S. F. Emmons

This mine is situated upon the western slope of the Meadow Valley mountains, about 70 miles by road from the present end of the railroad-track, which is at Uvada, on the UtahNevada boundary. This boundary-line marks fairly well a certain change in type of scenery from western Utah to eastern Nevada,—from a region in which the desert valleys predominate over the mountain ranges to one in which they are in about equal proportion. The railroad from Salt Lake City runs somewhat W. of S., for the most part along the bottom of the ancient Lake Bonneville. The latter part of its present course follows the axis of the southern arm or bay of that lake, now known as the Escalante desert. Along this bay, its line is a mathematically straight one, with no perceptible change of level for two " tangents " of more than 30 miles each, varying but a few degrees in direction. In the four or five hours re-

Jan 1, 1902

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936

By Leon Y. Sadler, E. K. Landis

Froth flotation has been described by several authors" as being analogous to a first-order rate process. Although a few investigators"," have found orders other than one fit their data best, the rate is described most often by the first-order equation, [ ] where r is rate of disappearance of floatable mineral by flotation, C(t) is concentration of floatable mineral in the cell, t is time, and k is first-order flotation rate constant. One of the difficulties in using this rate equation to develop a mathematical description of an actual flotation process is the determination of a suitable value of the constant k. The value of k, which reflects the floatability of the floatable mineral, is dependent on the hydrodynamic conditions in the cell, type and concentration of flotation reagents used, pulp density, and pH, method of froth removal, aeration rate, particle characteristics, and many other factors. Therefore, it is reasonable to expect that each particle of floatable material has a distinct value of k and that a unique distribution of k values exists for given feed and cell conditions. This has been observed and discussed by several investigators, and mathematical descriptions of the batch cell and steady-state continuous cell with distributed flotation rate constant have been developed." The mathematical description in the form of a transfer function of the continuous or flow cell under unsteady-state conditions with a distributed flotation rate constant has not been presented in the literature. The purpose of this note is to make such a presentation. The basic features of the perfectly mixed continuous

Jan 1, 1974

By Selma Hermann

For the past century, the so-called aluminum bronzes have been assuming a role of ever-increasing importance in the metallurgical field. The last quarter of that century has marked many efforts to find alloying elements that would alleviate some of the undesirable qualities of the aluminum bronzes-for example, the heterogeneity of the alpha solid solution and the extreme hardness of the beta. Much of this work, however, has been rather haphazard-compositions and heat treatment are usually so much at variance as to make comparison impossible. It is the object of this research to study the effect of certain percentages of common alloying elements on aluminum bronzes of analogous compositions and heat treatments. It is hoped that the material gathered here will at least serve as a basis for further systematic study.

Jan 1, 1930

By Augustus Locke

MY conclusions apply to the engineer in California ore hunting; and, because the product has been overwhelmingly gold, that means gold-ore hunting. But, I wish to think of ore hunting, not as employment for engineers, but as engineering. I wish, moreover, to think of it as productive of ore in significant quantity. The small mine, even if good, means little. Only new districts, or large extensions of old districts can engage our attention here. The conclusions are summarized as follows: (1) The bright color of California mining history comes from the suddenness and intensity of its outburst of gold. Had the mining been averaged from the start, it would soon have become dimmed among greater industries. For fifty years, California has proceeded as an agricultural, timber and oil, but not a mining region. 1

Jan 1, 1931

By AIME AIME

FOLLOWING careful study of the relations of the Institute to students and the younger members of the profession, the Membership Committee recommended to the Board a change of plans abolishing the Junior Associate class of membership, substituting a -Junior membership and providing for Student Associates. The Board adopted this report at its meeting on Nov. 23, and asked Counsel to draft the necessary amendments to the By-laws, and gave formal notice of intentions to amend as provided in Section I, Article XI1 of the existing By-laws. The By-laws as it is proposed to amend Article I, 11, 111, IV, X, and XI follow. The new plan requires no changes in the other Articles. The matter will come before the Board for vote on Jan. 25.

Jan 1, 1929

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZ92, (formerly ASTM No. 17; also known as Dowmetal C or AM260) which was done under "Restricted" Project NRC-21, in 1942-1943, and reported, in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZ92 was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZ92, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray analysis. From this figure it may be seen that above approximately 375°C (707°F), AZ92 alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a. two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, and because of its solubility relations, AZ92 resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ92 alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1947

By Carrol A. Quam

DURING the first years of operation of the titanium and iron mine of the National Lead Co. at Tahawus, New York, efforts to increase production were hampered by the increased load put on the facilities for sharpening churn-drill bits. The ore and rock are extremely hard and abrasive and it was necessary to sharpen and harden a large number of bits per day to keep the churn drills supplied. Efforts to increase the capacity of the bit shop by a two-shift operation were not wholly successful in that it was hard to train men to do a satisfactory job of sharpening and tempering the bits. The number of bits that were improperly tempered increased, thus boosting the daily requirements for bits at the drills and increasing the load on the bit-sharpening facilities.

Jan 1, 1949

By E. H. GRAFF

PREPARATION of mechanically loaded coal in mines where seams contain considerable impurities is a subject that requires careful consideration before machines are installed, unless provision is made at the tipple for its preparation. Conditions vary a great deal in the different seams, so much so that a mechanical loader may be unsuccessful in one seam and yet the same machine may make good in another where conditions are different. The effect of impurities in the coal seam on mechanical loading will also vary according to the thickness of the seam. In thin seams impurities will be more difficult to remove than from thick seams, as will appear later. For the past several years the New River Co. has done considerable experimenting with loading equipment and during this process has changed from one machine to another.

Jan 1, 1926

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965