Search Documents

By F. F. Aplan

INTRODUCTION The production of coal is a major part of the mining industry. In recent years the production of clean coal has exceeded 600 million tons per year and is reported to have reached 660 million tons in 1977. Some data on the magnitude and utilization for the year 1975 is given in Table I. In that year 648 million tons of soft coal were produced and of this 267 million tons or 41% approximately was produced by mechanical cleaning. Of the 374 million tons of raw coal sent to the preparation plant, 28.6% or 107 million tons was discarded as refuse. In the same year approximately 6 million tons of anthracite were produced and nearly all of this was cleaned. Table I also gives coal utilization statistics for 1975. Excluding the approximately 20% that goes to the coke ovens or to export, the vast bulk of our production is used for steam power generation and a lesser amount for captive production of industrial power and process steam. While much of the nation's coal (e.g. strip mined western, sub-bituminous coal) may be removed from the ground in relatively pure form by modest selective mining techniques, other coal requires preparation in order to remove ash and sulfur constituents and produce an acceptable steam or coking coal. Preparation is often a valuable adjunct to mining in that rather non-selective, low cost, bulk mining techniques may be used underground while the preparation plant is used to reject refuse at low cost above ground. The principal reason for the use of coal preparation is to convert raw coal into an acceptable commercial product by removing the high ash and high sulfur refuse material.

Jan 1, 1979

By E. P. Mathewson

In a discussion of a paper on The Basic Process as Applied to Copper Smelting, by Percy C. Gilchrist, read before the Society of Chemical Industry, London, Jan. 5, 1891,' Prof. W. C. Roberts-Austen asked Mr. Gilchrist whether he thought that the substitution of a basic lining for acid lining in the Manhks process would afford anything like the service which it had been shown to render in the metallurgy of iron. Claude Vautin stated that he had experimented for over two years. with basic linings for Bessemer converters for copper mattes at Cobar, but had given up the attempt on the score of cost. Mr. Gilchrist in his reply stated that he did not believe in applying any system of Bessemerizing to copper. About the time of the presentation of the paper mentioned,Hermann Keller, Superintendent of the Parrot smelter, in Butte, was experimenting on a large scale with converters lined with magnesite brick. He gave up the idea on account of the cost of linings and because no particular advantage was observed. My belief is that his tuyeres and converters were too small. A short time afterward similar experiments were tried at the Great Falls plant of the Boston & Montana Co., and at the Old Works of the Anaconda Copper Mining Co. in Anaconda. These were abandoned on the score of cost and the lack of advantages. The same cause of failure, in my opinion, holds here. The Anaconda Copper Mining Co., however, adopted the magnesite brick lining for its tilting casting machines. Fig. 1 is a view of the first tilting furnace casting copper. It was made from an old Brueckner roasting cylinder. Fig. 2 shows an elevation and vertical and horizontal longitudinal sections of the second tilting furnace, built in 1897.

Jan 1, 1914

By K. B. Nowels

DATA pertaining to pipe line flow for both oil and gas in horizontal or nearly horizontal pipe lines are both extensive and accurate. However, the pipe formulas used to determine pressure drop for flowing fluids (liquids and gases) under conditions of horizontal flow are not generally applicable to flowing oil and/or gas wells. Except for some data developed in small laboratory set-ups, little or no information was available concerning flow of oil and gas mixtures in vertical pipes, when, in 1928, the writer began the development of a method for computing pressure drops in the pipes of flowing oil wells, as outlined in this paper. In 1929, Uren1 presented some findings based on laboratory experi-ments in which vertical flow of an extremely heavy crude oil was induced, by means of air through a 2-in. pipe, 41 ft. long. The friction factors derived from the experiment, as well as values for pressure drop per 100 ft., are not believed satisfactory in their application to flow problems in the field. Versluys,2 also in 1929, presented a mathematical development of the theory of flowing oil wells, and in 1930, gave a companion paper3 setting forth some principles governing the choice of length and diameter of tubing in oil wells. Since the termination of the study presented in this paper, another. valuable contribution pertaining to the problem, of vertical flow was made by Moore and Wilde.4 Although there were writings dealing with the principles of the gas-lift, a search of the available literature indicated that specific information on vertical flow was lacking with the exception of the writings of Uren, Versluys, and Moore and Wilde, to which reference .has been made.

Jan 1, 1932

By W. A. Walker, G. W. Ostroot

An increase in the number of deep wells being drilled where extreme bottom-hole temperatures are encountered, and the anticipated drilling of wells where temperatures in the range of 500°F or higher may occur, has brought about a comprehensive investigation of cementing materials and of the techniques involved in their proper usage at these elevated temperatures. Included are developments in cements, retarders, weighting materials and other cement additives which make it possible to formulate a variety of compositions to help resolve the cementing problems of these extreme well conditions. The problems associated with the selection and testing of cements are discussed, and a resume of field results is included. Previous studies on strength retrogression indicate that caution should be exercised in the selection of a cementing composition for use in high-temperature wells. It now appears that, by the addition of silica flour as a stabilizing additive to certain cements, compositions covering a wide range of slurry densities can be designed to meet extreme well conditions without strength retrogression. Improvements in cement retarders make it possible to produce a four-hour thickening time at static temperatures up to 500°F. This temperature is considerably higher than conditions presently being encountered in drilling and completion work. Inert weighting materials, used to produce 20-lb/gal or heavier cement slurries, are reviewed. INTRODUCTION As the search for oil continues, the number of wells being drilled to depths of 10,000 ft or below has continued to increase over the past decade. During 1959, there were 50,893 wells drilled in the United States for a total of 209 million ft of hole. Of this total, approximately 4.45 per cent were drilled below 10,000 ft and 0.30 per cent below 15,000 ft, with a record depth of 25,340 ft recorded (Table 1). With the drilling of this record-shattering hole comes the question, "How deep can wells be drilled?".' Limitations with respect to equipment (surface and subsurface), cementing materials and techniques would cause some concern; however, a panel of experts have agreed that the U. S. oil industry has the equipment and know-how to drill a 50,000-ft hole. The greatest deterrent would be the 700°F temperature they would anticipate encountering at this depth. Although the number of wells drilled under what is generally considered hot-hole conditions (230°F and higher) has been relatively high, each well often presents distinctly individual problems and requires separate consideration and selection of special materials, techniques and equipment. At the present time there are over 30 additives and special cements available for use in "tailoring" a cementing composition for a specific well. It is not uncommon to use three or four different additives with the basic cement to produce the desired slurry characteristics. A generally accepted procedure is to make laboratory tests on selected cementing compositions prior to pumping them into wells deeper than 12,000 ft, or where static temperatures are in the range of 260°F or higher. In some instances, it is recommended that laboratory tests be made where less severe well conditions are encountered. Prior to selecting a cementing composition for a particular well, key personnel representing the operator, drilling contractor and service company should meet to determine that each individual is acquainted with every detail which might influence cementing results and to discuss the execution of the job. For cementing hot-holes, a number of factors must be evaluated before proceeding with the operation. Consideration must be given to the following. 1. Thickening time—The slurry must remain fluid for a sufficient length of time to allow displacement down the casing and up the annular space in a primary cementing job or, in squeeze-cementing, adequate thickening time for both the build-up of a satisfactory squeeze pressure and the reversing out of excess cement. The thickening time of standard retarded cements will often be too short under extreme temperature conditions, thus involving special formulations and requiring laboratory tests to determine the proper amount of additional retarder to obtain the desired pumpability.

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay hinders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County. The raw Wisconsin clay contained 65% quartz and 35% clay minerals. The Na20to CaO ratio was 0.234. Suspension viscosity tests of the raw clay gave results only slightly better than water alone, even after treatment with activator materials. Sedimentation treatment reduced the quartz in the decantate to 5% after 240 min (four hours). Twenty minutes of sedimentation produced a decantate with 27.5% quartz which was found as effective as the 5% quartz decantate in pelletizing behavior. The 20 min decantate was used in subsequent tests. The decantate was filtered and dried at 110°(230°F). The minus 200 mesh portion of this was added directly to the magnetite concentrate. Pellets were made in a laboratory sized disc pelletizer from pastes consisting of ore concentrate, balling water (9%) and binder (clay, or clay + resins, or resins). The pastes were premixed in a Waring blender. The binders were: (1) 1% of a commercially used Western Bentonite; (2) 1 % or 3% of the Wisconsin clay (raw, or 20 min decantate); (3) 20 min decantate washed with activator solutions, (to exchange Na for Ca in the clay); (4) decantate with activator added in the balling water; (5) decantate with organic resins; (6) organic resins. Measurements of the 0.46 m (18 in.) Green Drop Number, the Dry Strength and the Fired Strength (fired at 1260°C (2300°F) for 30 min) were made. The dry and fired compressive strengths were determined on an Instron testing machine using a C-load cell and a F-load cell, respectively. The cross-head speed was 0.004 m/sec (0.1 in./min) for both. The results of each measurement were averaged for 15 pellets. A summary of those results is presented in [Table 1]. More detailed results and procedures are presented in another report.7 In addition to the effects on pellet strength due to various binders the effect of varying magnetite concentrate characteristics is noted in [Table l]. There, a few comparative data are shown for Cornwall, PA Magnetite, which has a generally liner particle size than the Black River Falls magnetite which was used for most of the tests.

Jan 1, 1979

By O. N. Cole, R. E. Davis, T. D. Brotherton

Pvfoperties of rubidium and cesium are compared with those of other alkali metals. Methods for the preparation of rubidium and cesium metal are reviewed briefly, ad hazards and safety precautions required in handling rubidium and cesium metal are described. SimPle methods for handling laboratory quantities of elemental rubidium ad cesium under oil and under argon are illustrated. CESIUM and rubidium were both discovered by Bunsen and Kirchoff in the years 1860 and 1861. Cesium was discovered while Bunsen and Kirchoff were making a spectrographic study of spring water from Durkheim, Germany. It was the first element discovered by this technique. The element was given the Latin name "caesius" for sky blue because of the color it imparted to flames. Elemental cesium was first prepared by Setterberg in 1881 through electrolysis of a molten mixture of cesium and barium cyanides.' In 1861, Bunsen and Mirchoff discovered rubidium while making a spectrographic study of the alkali content of lepidolite ore from Saxony. Two prominent dark red lines appeared in the spectrum and so the element was named "rubidius" or dark red. In 1861 Bunsen and Kirchoff first prepared elemental rubidium through the electrolysis of molten rubidium chl~ride.~ The alkali metals are very similar in their chemical and physical properties. They are the most active metals, and all exhibit a single oxidation state of one. They are so reactive that they are never found in nature in the elemental state. The reactivity of he metals increases with atomic number. Rubidiurn and cesium ignite spontaneously in air and react explosively with water. This extreme reactivity makes necessary special equipment and techniques for the safe preparation and use of the metals. The cation: of Group IA can be separated from the metallic cations of other groups with relative ease, but the separation of the individual alkali cations is much more difficult because of their close chemical similarity. This close chemical and physical similarity of alkali metals can be inferred from the atomic radii, oxidation numbers, and ioni-zation potentials shown in Table I. A difficult but the most practical physical method of separating the elemental alkali metals from one another is by distillation. Only lithium has a boiling point sufficiently far-removed from the boiling points of the other alkali metals to make this method of separation feasible without elaborate and expensive equipment. This method is not used, however, for lithium because it possesses sufficient chemical dissimilarity from the other alkalies for it to be separated relatively easily as lithium hydroxide monohydrate or as lithium carbonate. Francium, the last member of the group, has no known stable isotopes. The naturally occurring

Jan 1, 1962

By H. C. George

With a growth of 718 per cent in the petroleum industry from 1901 to 1931, there was a corresponding increase in the demand for technically trained men in the industry. This was first met by increasing numbers of college graduates from the old established courses in chemistry, geology and engineering. However, a need began to be felt for scientists and engineers specially trained for the petroleum industry. In 1912 the University of Pittsburgh established the first department in any university in the world that offered major work in petroleum engineering and petroleum geology. In Europe, the first major work in petroleum engineering was offered in England in 1913 at the University of Birmingham. The University of California and Stanford University offered major work in petroleum engineering in 1915. Since that time at least 10 other American universities and colleges have offered major work and at least 12 others are now offering some courses dealing with petroleum and the petroleum industry.

Jan 1, 1934

By Chi-Yuen Wang, Chaw-Long Chu

The time-dependent volumetric constitutive relation for a San Andreas fault gouge and a consolidated kaolinite are experimentally determined at confining pressures to 200 Mpa, under creep condition and at ultrasonic frequency. At any given pressure, the bulk modulus determined at 1 Mhz frequency is identical to the "elastic" modulus determined at a stepwise change of pressure. After the pressure change, there occur a time-dependent change of volume and thus the effective bulk modulus. The constitutive relations may be modeled by a standard linear viscoelastic medium with pressure-dependent moduli and viscosity. For the San Andreas fault gouge, viscosity increases from 2x10 13 poise, at 17 Mpa, and 10 14 poise, at 100 Mpa. For kaolinite sample, the corresponding values are 3x10 12 poise and 10 13 poise. These results imply that both stress and pore pressure in fault zones may show time-dependent variations in response to a change of state of stress, such as that occurring after an earthquake.

Jan 1, 1982

By T. P. Meloy

In a recent paper, Gaudin and Meloy1 derived a size distribution function for single, impact fracture. Mular2 extended the use of this size distribution to describe the output of carefully controlled grinding experiments. As it stands, the function is difficult to compute. Consequently, a series of tables of the function are presented below: where M(x) is the cumulative fraction finer than size x when x is particle size. Weight percents are tabulated for the single parameter, r, in three different size ranges: from 0 to 1, from 1 to 10 and from 10 to 100. Tables I, II and III are cumulative percent finer and Tables IV, V and VI are for weight percent passing screen size x, retained on the screen below. A number of conditions from the table are plotted in Figs. 1 and 2. Fig. 1 is a plot of the cumulative percent finer vs. size, and Fig. 2 is the weight per-

Jan 1, 1963

By E. Hoek

The stability of a rock structure depends primarily upon the extent to which fracture develops within the structure, The prediction of the extent of potential fracture, the first step in the study of fracture development, involves a knowledge of both the stress distribution in the structure and the criterion which governs rock fracture under various stress conditions. While a great deal of research effort has been devoted to the development of techniques for analyzing the stresses in mining and civil engineering structures1-3 and to the investigation of the fracture mechanism of rock 4-6 relatively little attention has been paid to the application of available knowledge to the solution of practical engineering problems. This paper describes a photoelastic technique for the determination of potential fracture zones in certain types of rock structures. A practical example, based upon a problem which might be encountered in designing the layout of deep-level mine excavations, is given as an illustration of the application of this technique. STRESS ANALYSIS AND ROCK FRACTURE In deciding upon the technique to be used for the solution of a problem involving the prediction of rock fracture it is necessary to consider: 1) What type of stress information is required to satisfy the fracture criterion for rock; anti 2) How this information can most conveniently be obtained. It has been established, both theoretically 4,7 and experimentally 5,6,8that the fracture of hard rock depends primarily upon the relationship between the algebraically greatest and the algebraically smallest of the

Jan 1, 1967

By R. E. Schilson, F. H. Poettmann

The direct determination of the stabilized performance behavior of low capacity, slowly stabilizing gas wells is extremely time-consuming and wasteful of gas. From both field experience and theoretical considerations, a test procedure has been evolved by which the stabilized hack pressure behavior of such gas wells can he predicted without having to revert to long time flow tests. The method consists of using the isochrona1 test procedure to establish the slope of the back pressure curve, "n", and the short time variation of the performance coeficient, "C", with time. From this short time transient flow data and theoretical considerations, the value of C at large times can he established. By assuming the radius of drainage of a well to be half the distance between wells, one can calculate the stabilization time for various well spacing patterns. Once the stabilization time for a given .spacing has been determined, the value of C can be calculated and the stabilized back-pressure curve can he. establbrhed. The calculated perfortnance coefficient as a function of tinze was cotnpared to the experintentally measured values for a number of gas wel1.e. The deviation of the calc~*lated from the cxperimental res1tlt.s vary depending on the set of short time experimental points used to evabrate the parcrttzeters of the equation. The longer the tirne far the flow test data user1 in the calculations, the better was the agreement with the experimental results. The time necessary to obtain this data from well tests varies consitlerably, depending on the physical natrcre oj the rt3scrvoir under consideratiot~. INTRODUCTION For many years, the U. S. Bureau of Mines Monograph 7' has served as a guide for testing and evaluating the performance of gas wells by means of the back-pressure method. The back-pressure performance of a gas well is expressed by the following equation: Q~ CW-W.........(I) where the characteristics of the back-pressure equation are determined by C, the performance coefficient, and n, the exponent which corresponds to the slope of the straight line when Q and {P* - PN2) are plotted on logarithmic paper. Q is gas flow rate at standard conditions, and P, and P, are equalized and flowing bottom-hole pressures, respectively. Prior to the development of the back-pressure tcst, the "open flow" capacity method of testing a well was common. By this method, the wells were flowed wide open to the air and the flow rate measured. Such procedure was wasteful of gas and did not provide information on the deliverability of the gas to the pipe line. Monograph 7 Procedure The back-pressure method of testing wells was developed to overcome these shortcomings. Although much has been learned regarding the laws of the flow of gas through porous formations, the original development of the back-pressure relationship was based entirely on empirical methods. The back-pressure behavior provides the engineer with information essential in predicting the future development of a field. It permits him to calculate the deliverability of gas into a pipe line at predetermined line pressures, to design and analyze gas gathering lines, to determine the spacing and number of wells to he drilled during the development of a field to meet gas purchasers' requirements, and to solve many other technical and economic problems. As described in Monograph 7, the flow-after-flow method of back-pressure testing, when applied to fast stabilizing and usually high capacity wells, correctly characterized the behavior of the well. However, as the value of the gas at the wellhead increased, small capacity gas wells having slow rates of stabilization became economically operable. The flow-after-flow method of testing could not be used to describe the behavior of these slowly stabilizing wells. The procedure of Rawlins and Shellhardtl for establishing the back-pressure behavior of a gas well was based on the rcquirement that the data be obtained under stabilized flow conditions; that is, that C is constant and does not vary with time. C depends on the physical properties of the reservoir, the location, extent and geometry of the drainage radius, and the properties of the flowing fluid. In a highly permeable formation, only a very short period of time is required for the well to reach a stabilized condition, and, consequently, the requirements for the test procedure described in Monograph 7 are met. For a given well, n is also constant

By C. G. Dunn, P. K. Koh

TWO recent review papers have considered the origin of primary and secondary recrystalliza-tion textures from the point of view of oriented nucleation and oriented growth theories."' Both theories require nuclei for primary recrystallization but provide no unequivocal answer to the question of what nuclei are. The answer to the same question regarding secondary recrystallization, however, often is that nuclei are certain primary recrystallization grains or primaries. The two theories differ, however, in specifying what the certain primaries are. In support of the oriented growth theory Beck and Hua originally stated "It may be assumed that in a re-crystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as nuclei for the coarse grains, provided that conditions are favorable for their growth." In commenting on this statement one would say that there are two restricting conditions: namely, that 1) the certain primaries (nuclei) are large enough to grow, and 2) their boundaries have high mobility. More recently Beck2 has con-

Jan 1, 1958

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.' The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898' C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.' The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898' C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By Horace C. Porter

Most of the bituminous and semibituminous coals of this country will coke, and all of them yield, on carbonizing, more or less marketable gas and byproducts. We need, however, a finer distinction as between various grades of coking coals and between coals of different degrees of byproduct and gas-making possibilities. There is required by the consumer or the coal producer a dependable test to show whether a certain coal or mixture of coals will make coke of good commercial value for blast-furnace, foundry, water-gas, or domestic use; whether any difficulties in operation may arise from properties inherent in the coal; and whether gas and byproducts may be expected of good quality and in profitable quantity. For determining coke quality, the most dependable test is an actual run in an oven, but for byproducts a coal may better and more accurately be tested in the laboratory or in a miniature oven or retort. As to what are the most desirable qualities in blast-furnace coke, the furnace men themselves are not in complete agreement. Some desire a hard, well-burned, "hot" coke, and others get better results from a llgreener," less hardened product that burns somewhat more readily in the furnace. But certain qualities of cell structure and porosity are commonly agreed upon as desirable. Information as to what kind of coke a certain coal may be made to yield is valuable in advance, whatever may be the consumer's ideas as to the particular kind most suitable to his needs. The question arises, Can we predict coking quality with any degree of satisfaction from a small-scale test? It used to be said that coals could not be tested satisfactorily on a laboratory scale either for the coke they would yield or the byproducts. On account of the mystery with which the coking quality of coal has been shrouded and the large determining influences that many believe are exerted by mass, pressure, and the passage of carbonaceous volatile matter through the coking material, it has seemed difficult to reproduce in the laboratory the exact conditions of commercial practice. Great progress, however, has been made in recent years in elucidating the process of carbonization and many of the factors that make for the formation of high-grade coke and the recovery of the best

Jan 1, 1920

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a complex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of some of the more common evaluation tests made on coal and how the test results are applied in commercial practice should be of interest. Parameters used to select coking coal blends for wet and preheated charges should also be of interest.

Jan 1, 1982

By K. G. Colman

This text is intended to provide the operator and turn-key contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science, however, the information presented here should provide for reasonably accurate screen sizing when applied to metallic ores .

Jan 1, 1978

By E. A. Has, E. Mcl. Tittmann

Double roasting of sinter carrying a high percentage of lead concentrates, gave rise to the problem of removing the sheets of metallic lead formed in the wind boxes. The solution of the problem has been found in the water sealed wind boxes. The metallic lead is granulated and can be removed without seriously interfering with the operation of the machine and eliminates necessity of men going in wind boxes with air guns. THE practice of double sintering the charge for lead blast furnaces, which is now standard throughout the lead smelting industry, has introduced the rather difficult problem of cleaning the wind boxes on sintering machines used for the final pass. Two factors have more recently accentuated this problem: (1) the growing demand of workmen for better working conditions and less arduous labor, and (2) the growing dearth of crude lead ores and the improved grade of lead concentrates demand a charge carrying the maximum percentage of lead. One to 2 pct of such high lead charges (30 to 40) when processed on machines in reasonably good condition will pass through the grates and report in the wind boxes. One-half to three-quarters of this material will be metallic lead reduced by the coke breeze or other fuel mixed with the charge. This lead forms large cakes or chunks which are hard to remove and which substantially increase the time the machine is out of operation for cleaning the wind boxes. A high lead fall can reduce the operating time 30 pct. As a specific example, a 30 ft machine having 63 in. pallets, and equipped with three conventional wind boxes, requires 3 to 4 hr per day for removing the accumulation in the wind boxes when operated as a final pass machine. This same machine when operated on raw charge requires less than an hour per day for cleaning. To eliminate formation of large chunks of lead in the wind boxes of the final pass machines and time lost in cleaning the boxes, R. C. Rutherford of the Chihuahua smelter of the American Smelting and Refining Co., devised and patented* a wind box having a water bath to granulate the lead as it falls from the grate bars. Later, C. H. Harris of the San Luis plant made and patentedt an improvement on Rutherford's device in which the water bath seals the wind box in a manner permitting the latter to be readily cleaned without destroying the vacuum. The first machine to our knowledge to use the water bath box was at the Chihuahua plant along the lines of the Rutherford patent. In 1942, a machine was placed in operation at the El Paso plant which incorporated the features of both Rutherford and Harris. This machine is 40 ft long equipped with pallets 63 x 24 in., and having 4 wind boxes 10 ft 4 in. x 7 ft 2 in. x 51 ft 3 in. in size (fig. 1). The air from the fourth box is returned to the first three, and the gas from the first three discharged to a baghouse. The machine has conventional drive, discharge hopper,

Jan 1, 1951