Search Documents

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By J. B. Gwiazda

This work contains a description of a new design of lemniscate-guided powered roof support units, with a discussion of currently designed supports and their interaction with the roof. Conventional roof supports of this type present a serious reaction with the roof because of the horizontal displacement of the canopy in the course of decreasing support height as the support takes weight. The new design presented eliminates previous disadvantages of lemniscate supports and ensures proper performance of the latter in relation to the roof of a mine working.

Jan 1, 1986

The following resolution was passed by the Military Engineering Committee of New York on April 12, 1917. Copies are being sent to each member of Congress and to each of the five members in every State forming the committee representing, the five National engineering societies which carried on the industrial census under the direction of Howard Coffin. The Committee is urging every man to wire his Congressman and his Senator, asking him to do everything in his power to obtain favorable action by Congress on this resolution: Whereas in any large army to be created for the war, engineer troops will be needed in large numbers, and Whereas they should be officered by skilled engineers only, and Whereas the composition and training of such troops differ so much from the composition and training of non-technical troops that they should be organized under one central authority rather than under many scattered authorities. Now, therefore, be it resolved: That the members of the Senate and House of Representatives be requested to insist that all new units of engineer troops be organized and maintained by the War Department and not by the individual States.

Jan 6, 1917

By John S. Rinehart, Norman Ahlquist

The model which Birkimer has developed to explain the increase in fracture strength of brittle, rock-like materials with increasing rate of loading may have some applicability. It should be noted that since his analysis presupposes elastic behavior he could equally well express his result as an increase of stress to fracture with increasing strain rate, a fact which is well known. Certainly his experimental results do not contradict his strain rate to the one third power law. On the other hand, we do feel that the data are insufficient and inadequate to establish the relation- ship definitely. 'In metals, the whole fracture picture is greatly complicated by concomitant plastic flow and, in rocks, by the presence of macroscopic flaws and inhomogeneties. Both lead to uncertainties as to the state of stress during the fracture process. He quotes in support of his theory Rinehartfs results on rock in which the latter found that under impulsive loading by explosives, rocks appear to be many times stronger than under static loading. We suspect that the observed increase has little specific relevance to the theory which Birkimer puts forward. Rinehart's measurements were made by spalling rocks using a sawtooth shaped stress wave of known intensity and duration. The rise time of such a pulse is essentially zero, certainly less than 0.1 microseconds, so that it is not possible to apply Birkimerfs theory quantitatively. We favor attributing the increase in fracture strength to two factors. First, the action takes place very quickly in an exceedingly thin region so that statistically the probability is small of encountering one or more of the large flaws that contribute so significantly to the reduction of strength of most rocks under tension. It is also conceivable that the compressive wave that has just passed by the region of fracture has strengthened the rock by collapsing some of the larger flaws. Second, the state of stress obtaining at the time of fracture is not all that existing when the

Jan 1, 1971

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period June 10, 1917, to July 10, 1917. Guy N. Bjorge, Boston, Mass. H. H. Lauer, Allentown, Pa. A. H. Burroughs, Jr., Britannia Beach, E. C. Lee, Pittsburgh, Pa. B. C., Canada. Montrose L. Lee, Port-au-Prince, Hayti. Karl Eilers, New York, N. Y. Eugene McAuliffe, Paducah, Ky. H. S. Emlaw, Grand Haven, Mich. R. H..McMillen, Pittsburgh, Pa. W. R. Hamilton, San Francisco, Cal. L. D. Moore, Providence, R. I. Fred N. Hays, Sharon, Pa. Fred J. Pope, New Rochelle, N. Y. E. Hibbert, Nickelton, Ont., Canada. George S. Rice, Washington, D. C. Charles Janin, San Francisco, Cal. W. G. Swart, Duluth, Minn. Milton A. Allen has resigned his position with the Federal Lead Co. and accepted a position with the Arizona State Bureau of Mines, Tucson, Ariz. L. W. Bahney has resigned as Professor at Yale University and accepted a position as metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn.

Jan 8, 1917

By R. W. Smith, R. W. M. Lai, J. Leja

J. Leja (Professor, Dept. of Mineral Engineering, U.B.C. Vancouver, Canada) — I would like to offer some comments on the behavior of contact angle with time, treated in this paper. The authors should be congratulated for a clear exposition of these uncommon departures in the correlation between flotation and contact angle, in systems of importance to industrial practice. Some nine years ago Professor J. H. Schulman (presently at Columbia University, New York) and I reported on a similar study conducted at the Ernest Oppenheimer Laboratory, Cambridge, England.' The systems used by us had, how- ever, no direct practical application at that time, as mercury in solutions of xanthates was tested with a variety of alkyl-aryl polyoxyethylene frothers which were then new to flotation practice. Further, the paper dealt with findings contrary to the then widely held belief that the contact angle established in collector-solution is unaffected by the addition of a frother. Correlation with flotation, or lack thereof, was not sought, though we did suggest that in many cases the selectivity of frothers might be influenced by the dynamic contact angles. We also stated (on p. 243,

Jan 1, 1968

By John C. Ludlum

A most stimulating event in the development of world mineral production and technology, the Eighth Commonwealth Mining and Metallurgical Congress was convened at Melbourne Town Hall on March 1 by Sir Maurice Mawby, President of the Congress. Continuing successively at Melbourne, Canberra, Sydney, and Surfers Paradise in Australia and then at Wellington, New Zealand, the four plenary sessions, 50 technical sessions, and both local and extended mine and plant tours during the seven weeks of the Congress, provided a superb medium for assessing the present and looking into the future. There were more than 2300 participants from 32 countries in the various functions of the Congress, including 500 delegates and wives from countries other than Australia and New Zealand, and from 18 countries not members of the British Commonwealth of Nations. Registrants from South Africa numbered close to 200 and there were about 100 from Canada, 70 from the United Kingdom, 60 from the United States, and 20 from Zambia. Although most of the overseas delegates held administrative positions with companies, government agencies, and colleges or universities, professions identifiable from registrations included 100 engineers, 60 geologists and 30 metallurgists.

Jan 8, 1965

By G. S. Hume

Three provinces in Canada—New Brunswick, Ontario and Alberta— produce oil and gas in commercial quantities. In addition a small amount of oil is being produced and refined in the Northwest Territories at Norman on the Mackenzie River. The production at Norman is derived from two wells drilled by Northwest (Imperial Oil) Co. in 1920 and 1923. The refined products of the oil are used locally in connection with mineral developments on Great Bear Lake. The production of petroleum by provinces and the consumption of natural gas are shown in Table 3. In addition a small amount of natural gas is produced in the southwestern part of Manitoba from shallow wells for local use. Tables 1 and 2 give detailed information. The greatest drilling activity in 1933 in Canada centered around the southern end of the Turner Valley field, Alberta. In addition to several wells previously commenced in this area, eleven new wells were begun. There were three completions to the Paleozoic producing zone in 1933 in the southern part of Turner Valley and one well was abandoned as a result of being off the favorable structure. Of two wells completed in

Jan 1, 1934

By R. J. Wysor

Discussion of the paper of R. J. WYSOR, presented at the New York meeting, February, 1916, and printed in Bulletin No. 106, October, 1915, pp. 2161 to 2170. LEONARD WALDO, New York, N. Y.-Will Mr. Wysor kindly give us more information as to the pyrometers used and the temperature measurement? R. J. WYSOR, So. Bethlehem, Pa.-We used standard Bristol pyrometers with bare fire ends. These were standardized both before and after the tests with salt and pure aluminum. We also interchanged the pyrometers. J. W. RICHARDS, So. Bethlehem, Pa.-Did you attain any results which gave you approximately the value of the heat insulation at any of the furnaces? R. J. WYSOR.-In the first installation we were afraid to put in the insulation throughout the hot-blast main for the reasons mentioned in the paper, but we used the insulating brick in two 8-ft. sections in straight lengths of our hot-blast mains. Owing to the high conductivity of the steel shell, the temperatures which were taken on the outside were not representative of the two temperatures resulting from heat flow through the insulating brick. I believe that when a hot-blast main is insulated

Jan 5, 1916

By Stuart Croasdale

NOT long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale.

Jan 8, 1914

By Edwards Wichers

The purpose of this paper is to set forth the matters of principal interest in connection with work done in the past few years on the purification of the metals of the platinum group, including the study and modification of methods already in the literature and the development of new procedures. For the most part, the results will be given in summary form, reserving the publication of detailed data and directions for a forthcorning paper to be issued by the Bureau of Standards. In recent years increasing interest has been shown in the preparation of the pure platinum metals, both by those concerned with the manufacture of the metals and their alloys for scientific and industrial purposes and those who are engaged in the study of the chemical or physical properties of the elements. The purification of the metals usually has been regarded as a matter so involved and difficult as to require the attention of specialists. It is hoped that this paper will show that any of the metals can be prepared in any desired degree of purity by relatively simple straightforward chemical methods. For the most part, it is thought that the methods given are suitable for small-scale refineries as well as for the laboratory; also, that they will bring the time required for the purification of any of the metals within reasonable limits. The new procedure suggested for purifying platinum should prove to be much shorter than any methods described in the literature. Treatment of Platinum Ore As is well known, the principal source of the platinum metals is a mixture of several native alloys of the metals, found chiefly in naturally concentrated deposits in stream beds or alluvial material. Without attempting to enumerate all of the minerals present, it may be said that the concentrated ore from such sources contains all of the six platinum

Jan 1, 1928

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, )"Why automate?" Automation, automatic control devices and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with a minimum of instruments for the purpose of merely guiding the operators. Processes were manually controlled by the operator on the basis of simple temperature, pressure, flow and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction savings in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material through- put, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins or producing a new and saleable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure, and (2) units which both measure and control a process variable. In coal processing, the first class of instruments, those which measure only, include analytical devices such as automatic ash, moisture and sulfur measuring units and the simple pressure, temperature, flow and level indicating devices mentioned previously. The second group of instruments, those which both measure and control, include a wide variety of units such as continuous weighing devices on conveyor belts and photoelectric cells which gauge the position of railroad cars on the track and insure that the cars are in the proper location for loading (see Chapter 15). The latter types of units as used in the coal industry differ from those used in other industries in one significant point. In coal processing these instruments need not be as highly sophisticated and accurate as in other industries; hence their cost is proportionately lower than in other industries. Because of the economic fact that coal sells for only a fraction of a cent per pound compared to dollars per pound for many chemical products, and

Jan 1, 1968

[Holds monthly meetings, except June, July and August, J JOHN A. CHURCH, JR., Chairman JOSEPH E. POGUE, Vice-chairman SIDNEY ROLLE, Vice-chairman EDWARD C, MEAGHER, Secretary, Texas Gulf Sulphur Co,, 41 E, 42nd St., New York M, H, MERRISS, Treasurer, 42 Broadway, New York ARTHUR NOTMAN T. T, READ Boston Meets first Monday of each winter month. EDWARD C. GEITHER, Chairman WILLIAM S. BLACK, Vice- chairman DONALD H, MCLAUGHLIN, Secretary, treasurer, Rotch Bldg,, Harvard Univ,, Cambridge, Mass. J, L. GILLISON A. G, WAITE]

Jan 1, 1928

PROF RICHARD ÅKERMAN Stockholm, Sweden DR FRANK DAWSON ADAMS Montreal, Canada ANDREW CARNEGIR New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England HERBERT C. HOOVER Leoben, Austria JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE, POURCEL Paris, France PROF RICHARD H, RICHARDS Boston Mass. JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1923

PROF RICHARD ÅKERMAN Stockholm, Sweden PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HOFFER Leoben, Austria PROF HENRI LOUIS LE CHATELIER Paris France M FLORIS OSMOND Paris, France ALEXANDRE POURCEL Paris, France JOHN E. STEAD Middlesborugh, England DR. ING H. C. EMIL SCHROEDTER Dusseldorf, Germany JAMES M. SWANK (Associate) Philadelphia, Pa. PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washingtion D.C.

Jan 1, 1910

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W, FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W..RODDEWIG, Vice-Chairman. LYNDON K, ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 7, 1914

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman. WILLARD S. MORSE, Vice-Chairman. . THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON, Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 6, 1914

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE,. Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 8, 1914

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York. N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 9, 1914

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman. WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN; Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 1, 1915