Search Documents

By John T. Norton

In spite of the very general errlployment of nitride hardening, there is still considerable doubt as to the real nature of the mechanism involved. Experience has shown that the addition of small amounts of hardening elements to iron or steel results in a wide variety of desirable properties in a nitrided case. Perhaps the foremost of these elements is aluminum and in this investigation an attempt has been made to study the behavior of aluminum during the hardening process. It is believed that the establishment of a complete atomic picture of the metal at various stages of the process will indicate the relationships between the several kinds of atoms and their individual influences on the physical properties in a clear and direct fashion. A consideration of the problem suggests a surprising similarity between the mechanisms of nitride hardening and of age-hardening. It is now generally understood that age-hardening may take place by one of two distinct processes, the first involving the precipitation of a finely dispersed phase and the other being concerned with the modification of an existing phase. Following much the same line of reasoning, two theories of nitride hardening have been suggested. The first explanation, which has been generally discussed, particularly by Fry,' states in brief that the presence of aluminum causes the precipitation of aluminum nitride during nitriding and that this finely dispersed phase is the primary cause of hardening. The second explanation, which has not been published but which has been freely discussed by those interested in the problem, postulates the substitution of aluminum atoms for certain of the iron atoms in the several iron-nitrogen phases in the same manner that the substitutional iron-alurninurn solid solution is formed. The marked increase in hardness, as compared with the aluminum-free system, is attributed to the severe lattice distortion accompanying this replacement.

Jan 1, 1934

By Reinhardt Schuhmann JR

Metallurgical Engineering Volume I, by Reinhardt Schuhmann, Jr. Addison-Wesley Press. $7.50, 390 pp., 1952. -This first volume, engineering principles, of a two volume work, is intended by the author to meet a need for reorganization of instruction in extractive metallurgy. Its three main objectives are to organize the subject matter according to basic principles and unit processes; to integrate the underlying science of physical chemistry with metallurgical engineering; and to put greater emphasis on analysis and quantitative solution of engineering problems. Vol. I deals with unit processes, stoichiometry, thermodynamics, fuels, fluid flow, heat transfer, pyrometallurgical systems and refractories. Vol. II will take up the individual unit processes. Initiation and Growth of Explosion in Liquids and Solids, by F. P. Bowden and A. D. Yoffe. Cambridge University Press. $4.50, 104 pp., 1952.-The book is a study of decomposition by impact and by friction of explosive substances and deals mainly with the work of the authors and their collaborators. Research is still in progress but results thus far indicate that the mechanism of initiation is relatively simple. Findings are thoroughly discussed, and the latter part of the monograph describes the way in which a small nucleus of decomposition can grow into a large scale explosion.

Jan 1, 1952

By W. A. Hoyer

A pulsed high-energy neturon-induced spectral logging tool has been built and field-tested. The reaction of deuterium on tritium is used to generate pulses of 14-Mev neutrons. By detecting only the prompt gamma rays produced by neutron inelastic reactions in the formation, the presence and relative abundance of carbon, oxygen, calcium, silicon and other important elements may be ascertained from a gamma-ray spectrum. Gamma-ray spectra obtained in a shallow test well and in experimental field use show that it is possible to identify formations and their contained fluids. INTRODUCTION The penetrating gamma rays from naturally occurring radioactive elements in subsurface formations have been used for a number of years in well logging as a means of characterizing and distinguishing strata. Still another nuclear logging method which has been employed for some years consists of the bombardment of strata with neutrons and the measurement of the number of gamma rays produced by neutron capture reactions involving elements in subsurface strata.' Since one of the principal elements entering into capture reactions is hydrogen, the latter procedure essentially results in a hydrogen log, whether the hydrogen be in combined form in either oil or water; thus, the log gives an indirect measure of porosity. These methods, with various refinements, have been developed to such an extent that they have become routine procedures in formation evaluation. Neither gamma-ray logging nor conventional neutron logging, however, yields sufficient information to permit unequivocal identification of the mineralogic composition of formations, and neither method gives information which may be used for the positive identification of hydrocarbons in strata. Accordingly, a number of efforts have been made in recent years to gain additional information from nuclear logs. Brannon and Osoba have shown that it is possible to identify naturally occurring radioactive elements in subsurface formations by spectral analysis of gamma rays emanating from these elements. Such an identification is of value in the characterization of strata. A simplified form of spectral analysis of gamma radiation resulting from neutron capture reactions between elements in earth materials and bombarding neutrons has been used with some suc- cess under favorable conditions to differentiate between petroleum and water. This method relies upon the relatively high energy of gamma radiation from neutron capture by chlorine and, in effect, furnishes a chlorine log. In areas in which interstitial water is of sufficiently high salinity, this log can give valuable information on water saturation and, thus, indirectly on hydrocarbon saturation. Still another approach to obtaining more information by nuclear techniques is "activation logging", in which certain elements yield short-lived radioactive isotopes on neutron activation and, thus, can be detected by gamma-ray spectral analysis. From the standpoint of determining by nuclear logging methods the mineralogic composition of strata and the presence or absence of hydrocarbons, it is essential that information be obtained on the presence and relative amounts of several elements such as carbon, oxygen, hydrogen, calcium, silica and others. Some elements, such as hydrogen, chlorine and sulfur, can be determined by spectral analysis of gamma radiation resulting from neutron capture reactions."" Others — carbon and oxygen, for example — do not enter readily into capture reactions but do yield gamma rays of characteristic energies from inelastic scattering reactions with high-energy neutrons. Accordingly, the latter reactions are of particular interest as a means of identifying hydrocarbons in subsurface strata. Several years ago it was recognized that information requisite to the identification of subsurface strata and of contained fluids could be obtained by pulsed operation of a subsurface neutron generator and associated gamma-ray detector. It was contemplated that pulsed operation would be effective in discriminating in time that gamma radiation which results predominantly from inelastic scattering reactions from that gamma radiation arising from neutron capture reactions. Accordingly, research was continued and construction of such a device was initiated. Although many problems were encountered, they were solved successfully. The following sections describe the tool which has evolved, its performance and the results which have been obtained with it to date. THEORY OF OPERATION OF NEUTRON-INDUCED GAMMA-RAY SPECTRAL LOGGING TOOL THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bombarded with neutrons, emits gamma radiation of energy characteristic of that element. In theory, therefore, an element may be identified by

By Charles Russell

PRESSURES developed by the coal during the coking process have been responsible for serious trouble to many companies that operate or build by-product coke ovens. The insidious nature of this trouble is indicated by the fact that oven operators, unless they have ascertained the charac-teristics of the coals they use, cannot determine the existence of dangerous pressures until after the damage has been done. A rather popular mis-conception is that ease of pushing of the charge at the completion of the coking period indicates that no dangerous pressure has been developed, but this is far from the truth; pressures developed during the coking period are often completely dissipated by the shrinkage of the charge in the completion of coking, and so any criterion based on the ease of pushing is futile. However, methods of testing coals are available that will definitely distinguish the dangerous coals from those that are safe, and such methods have been brought to a high degree of certainty. The operator should take no risk that involves either a lack of knowl-edge of the behavior of coals during coking or the failure to believe that certain of the coals or coal mixtures can cause damage to the oven struc-ture. This merely tends to minimize the problem and leads to claims that coking coals of all kinds may be carbonized with no danger of damage to the oven structure provided some particular kind of by-product oven is used. This lack of appreciation of the true situation is in itself one of the main factors leading to damage of coke-oven structures. Coals that develop more than a certain safe pressure cannot be used in by-product coke ovens without causing damage to the side flue walls. The following paper presents a highly certain method for the measure-ment of the pressures developed during the carbonization of coal-a method that is the culmination of many years of work on the problem in which a number of methods for the purpose were investigated and used. While actual pressures found may appear to be small when expressed in pounds per square inch, the number of square inches in each oven wall is so large that the total pressure on the oven wall becomes an enormous load.

Jan 1, 1939

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By W. R. Johnson, M. Hansen, John M. Parks

AS part of a research project sponsored by the Signal Corps Engineering Laboratories, which had the objective of obtaining a magnet wire of good conductivity and low temperature coefficient of resistance, a comprehensive literature survey, supplemented by experimental work, revealed that a linear relationship exists for solid-solution alloys between the electrical conductivity, K, and the temperature coefficient, a, as expressed by the equation: k = a/ß where ß is constant for the solvent metal and a - per°C. tR0 It has long been known that the electrical conductivity at a given temperature and the temperature coefficient of resistance of binary alloys are related to their constitution by the LeChatelier-Guertler rules, as illustrated by Figs. 1 and 2: Rule 1—In alloy systems consisting of a heterogeneous mixture of two phases, the electrical conductivity and temperature coefficient vary as a straight line, if the composition of the alloys is given in volume percentage, Fig. 1. Rule 2—In solid solutions, the electrical conductivity and temperature coefficient are always lower than those of the solvent metal, and usually a considerable decrease occurs with the first small percentage additions of the solute metal, Fig. 2b. If the two components form a continuous series of solid solutions, the electrical conductivity and temperature coefficient curves take the form of a U-curve, Fig. 2a. That some kind of proportionality exists between electrical conductivity and temperature coefficient of resistance is implied by the LeChatelier-Guertler rules and by study of data such as those given by Smith and Palmer,' Fig. 3. Dellinger2 in 1910 first recognized this relationship in a number of commercial copper wires, ranging in conductivity from 94 to 100.7 pct I.A.C.S. He gave the ratio of temperature coefficient to the percentage of conductivity as a constant, C = 0.003939. A year later, Lindeck observed that the linear relationship was valid for a wider range of conductivity in "various sorts of copper," and concluded that the product of resistivity and temperature coefficient was 6.78x10-5 1.5 pct. Since then, this relationship seems to have been entirely ignored. Conductivity-Temperature Coefficient Relationship If the electrical conductivity of copper solid-solution alloys with phosphorus, silicon, arsenic, antimony, aluminum, nickel, manganese, and iron is plotted against the temperature coefficient of these alloys, the diagrams in Figs. 4 and 5 are obtained. Similar data were found with copper-rich solid solutions containing magnesium, cobalt, and titanium,'" as shown in Fig. 6. In all cases, a linear relationship exists. The point representing the highest

Jan 1, 1952

By T. Sterry Hunt

BUT little was known of the coals of Southeastern Ohio until the present survey of the State under Dr. Newberry began its work. The results of the geological investigations of Prof. E. B. Andrews in this region, and of the chemical investigations of Prof. T. G. Wormley, both of which appear in the reports of the survey for 1869 and 1874, and more recent special reports by the former, together with some data for which I am indebted to the kindness of Dr. Newberry, and my own limited observations, have served me for the preparation of the following notice of the coals lying on the western border of the great Appalachian coal-basin in the region drained by the Hocking River and its tributaries, and belonging to the Lower Coal-Measures. Some uncertainty exists as to the place in the succession of the lower coals to be assigned to the seams known and mined in the Hocking Valley. It is the opinion of Prof. Andrews that the inequalities of the original surface were such that we cannot identify in that region the lowest coals known in Northwestern Pennsylvania and the contiguous parts of Ohio, but that we must rather count from above downwards. These conclusions Dr. Newberry is not prepared to accept, and further researches will be necessary before certainty can be attained in this matter. Meanwhile it seems, from a study of its relations to the Pomeroy or Pittsburgh seam, that what is known as the great vein of the Hocking Valley, occupies the horizon of the Upper Freeport coal, E of the Pennsylvania survey, or No. 6 in Dr. Newberry's enumeration, counting from the base. This seam, in the region in question. assumes certain characteristics which, taken in connection with its geographical position, give it a great importance among the coals of the State. The area to be noticed includes the whole or parts of several townships in Perry, Hocking, Vinton, and Athens Counties, lying near the margin of the basin over which the vein in question assumes the character of a dry-burning or splint coal, and has a thickness varying from six to ten and even twelve feet. Its precise limit southward cannot at present be clearly defined, but it has been found as far south as the line of the Marietta and Cincinnati Railroad, with a thickness of six feet, and is mined at various points along the valley of the Hocking River, near Nelsonville, where it attains six or seven feet. To the northward, along the tributaries of this river, Sunday and Monday

Jan 1, 1874

By F. J. Mehringer, C. W. MacGregor

VARIOUS investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-12 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 [ ] where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. PRELIMINARY INVESTIGATIONS The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 019 per cent; S, 0. 118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Elect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By Harold Markus, Arthur H. Grobe, Gerhard Derge

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study. has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from 1/2 to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.? After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been damped. The pH of the electrolyte was controlled? by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.10. Potentials were measured against a saturated calomel electrode connected. to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By J. E. Johnson

THE production of metal-working tools has been revolutionized within the last 18 years, since the invention by Taylor and White of a process of heat-treating steel tools, which resulted in increasing their cutting capacity several fold over what it had been before. This was an exceedingly important invention, although it consisted principally, in establishing this fact overheating when it accidentally, occurred in the ordinary:-process of forging, spoiled the steel, but if carried very much farther or to-a point that would have been considered absolutely ruinous to the steel under the old ideas, it resulted in imparting a cutting power several times as: high as had ever been obtainable before. The quality that gives the steel this power eventually received the name of "red hardness." This name originated in the fact that tools possessing this property retain their resistance to deformation even when subjected to, such severe cutting stresses that the metal just back of the point is heated, under certain conditions, to a visible red. It is interesting in this connection to note that the edge of the tool itself does not become red because it is continually cooled by the fresh metal into which it is forced. The result of Taylor and White's invention was an intensive study, of tool steels all over the world and, although there was-great diversity of analysis in the high-speed steels of the early days, these steels today generally have an approximately similar composition, the principal constituents being froth 15 to 20 per cent. of tungsten, from 4 to 6 percent. of chromium, from 1 to 2 per cent. of vanadium, and from 0.50 to 1 per cent. of carbon. It is probably safe to say that standard brands of such high-speed steels will do from five to ten times as much work in a given time as the carbon steels, and even the Musket steels, which were the sole dependence up to the beginning of this century, when the Taylor-White process was discovered. With the increasing cost of labor, it is not surprising that these steels have driven froth the market, for all but limited purposes, the older types of steel.

Jan 2, 1919

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 ('other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

By C. A. Edwards

Following a brief introduction, an outline is given of the four main conditions in which gases may be associated with metals; namely, (1) adsorbed gases, (2) dissolved gases, (3) gases in chemical combination, (4) gases entrapped in blowholes or cavities. Adsorption is essentially a surface phenomenon and is regarded as the attachment of outside molecules or atoms to the exposed free valencies of the atoms comprising the surface layers. In many cases where adsorbed films of gas are formed this is accompanied by a process of diffusion of the gas into the metal itself. This is particularly true in respect to iron and hydrogen, and experiments have shown that there is no difference between the rate at which hydrogen diffuses through a single crystal of iron arid through the same material after it has been recrystal-lized into a mass of small crystals. This does not prevent a somewhat greater concentration of gas at the boundaries of adjacent crystals, nor does it mean that the effect of the gas will be the same at the boundaries as it is within the body of the crystals. Indeed, under certain conditions, iron is rendered very brittle at the crystal boundaries, as shown in experiments by Pfeil with samples of almost pure iron. Much work has been done by many investigators concerning the temperature and conditions under which dissolved hydrogen, in particular, can be at least partially removed from different metals. With iron, the hydrogen that has diffused into the metal as a result of acid attack by pickling or by electrolytic deposition of the gas on the metal is partly removed by exposing the metal to the atmosphere at ordinary temperatures. Considerably more can be eliminated by raising the temperature, and even greater quantities by jointly raising the temperature and reducing the pressure. Annealing at suitable temperatures completely removes the bad effects of excessive mounts of hydrogen dissolved in or associated with iron. This is shown by the data plotted in Fig. 1, giving values for electrolytic iron sheets after annealing at temperatures between 250" and 950" C. The hydrogen brittleness is rapidly diminished at

Jan 1, 1935

By C. A. Edwards

Following a brief introduction, an outline is given of the four main conditions in which gases may be associated with metals; namely, (1) adsorbed gases, (2) dissolved gases, (3) gases in chemical combination, (4) gases entrapped in blowholes or cavities. Adsorption is essentially a surface phenomenon and is regarded as the attachment of outside molecules or atoms to the exposed free valencies of the atoms comprising the surface layers. In many cases where adsorbed films of gas are formed this is accompanied by a process of diffusion of the gas into the metal itself. This is particularly true in respect to iron and hydrogen, and experiments have shown that there is no difference between the rate at which hydrogen diffuses through a single crystal of iron arid through the same material after it has been recrystal-lized into a mass of small crystals. This does not prevent a somewhat greater concentration of gas at the boundaries of adjacent crystals, nor does it mean that the effect of the gas will be the same at the boundaries as it is within the body of the crystals. Indeed, under certain conditions, iron is rendered very brittle at the crystal boundaries, as shown in experiments by Pfeil with samples of almost pure iron. Much work has been done by many investigators concerning the temperature and conditions under which dissolved hydrogen, in particular, can be at least partially removed from different metals. With iron, the hydrogen that has diffused into the metal as a result of acid attack by pickling or by electrolytic deposition of the gas on the metal is partly removed by exposing the metal to the atmosphere at ordinary temperatures. Considerably more can be eliminated by raising the temperature, and even greater quantities by jointly raising the temperature and reducing the pressure. Annealing at suitable temperatures completely removes the bad effects of excessive mounts of hydrogen dissolved in or associated with iron. This is shown by the data plotted in Fig. 1, giving values for electrolytic iron sheets after annealing at temperatures between 250" and 950" C. The hydrogen brittleness is rapidly diminished at

Jan 1, 1935

By Leroy U. Gardner

The human respiratory tract is an apparatus for the interchange of gases between the air and the blood. An important part of it are mechanisms to prevent the apparatus from becoming clogged with dust particles that are inhaled with the air. These mechanisms are adequate to protect the organ against most dusts, but silica and at least one of the silicates, asbestos, are tissue poisons which initiate changes in the connective tissues of the lung, incompatible with function. Silica is concentrated by the phagocytes in contact with the connective tissues of the lymphatic drainage system. An overgrowth of connective tissue occurs which interferes with the function of this system. More dust that may be inhaled can no longer be effectively eliminated from the lung. It accumulates in the functioning part of the organ and excites the formation of characteristic fibrous nodules and bands. These changes seriously impair the respiratory function. The shadows of such changes cast upon an X-ray film of the lung are discussed. The reaction to silica in the lung produces a marked increased susceptibility to tuberculous infection. It can be reproduced and studied in the experimental animal and has been observed repeatedly in human beings. Asbestos dust also causes fibrosis in the lungs but the mechanism of its development is different. The fibrous dust settles along the irregular walls of the terminal bronchioles. In this location it excites the formation of cuffs of scar tissue. This contracts and shuts down the tubes, resulting in a collapse of the air spaces distal to the obstruction. Such a condition in itself is a cause of fibrosis. The two causes, immediate reaction to the dust and collapse of the finer air spaces, bring about a generalized diffuse fibrosis. This reaction is not so regularly associated with increased susceptibility to tuberculosis as with silicosis. The case against sericite as a cause of silicosis has not been proved. Experimentally, sericite-free quartz will produce nodular fibrosis. Silicon carbide and aluminum oxide are quite inert in the normal animals. The former apparently increases susceptibility to tuberculosis in animals but whether the same is true in human beings awaits demonstration.

Jan 1, 1934

By D. Harrington

During the past few years, there has been a trend toward the use of rock-dusting, rather than relying on humidifying, or the use of water, to limit or prevent explosions in the coal mines of the United States. This is partly because British coal mines have adopted rock-dusting and, at least in a sense, have condemned the use of water. Moreover, during the past few years, particularly in the latter part of 1922 and in 1923 and 1924, several explosions with heavy loss of life occurred in coal mines of the United States that were known to have more or less extended sprinkling, or humidifying, systems. The sentiment created by these disasters quickly caused a distrust of explosion-prevention methods requiring use of water and simultaneously caused more or less of a stampede into rock-dusting. Much of the wholesale condemnation of watering methods was without adequate knowledge, or at least without adequate consideration, of local conditions in each case, and rock-dusting was adopted largely without sufficient knowledge of how to rock dust safely or correctly. However, mines that had been using watering methods and had suffered these recent serious disasters (notably Dolomite, Dawson, and Castle Gate) instead of abandoning the use of water when operations were resumed after the disaster, greatly extended their watering systems. At the same time they took other precautions as to electricity, ventilation, blasting, etc., and supplemented the watering system with rock-dusting where the latter was likely to be the more effective. The trend toward rock-dusting during the past year or two (succeeding the recent mine disasters) is very similar to the rapid movement toward watering, or humidifying, methods, about 1910 to 1912, after a series of disastrous mine explosions. The Phelps-Dodge Corpn., which operates a large property at Daw-son, N. M., after an explosion in its No. 1 mine in February, 1923, decided that it is dangerous to have all its "explosion-prevention eggs in one basket" and so adopted what may now be termed the Western coalmine explosion-prevention system, in which both rock-dusting and watering are used, supplemented by other up-to-date mining methods and practices; such as exclusive use of modern electric safety lamps, with magnetically locked flame safety lamps for testing purposes; use of

Jan 1, 1925

By G. W. Garside

In order to render my descriptions more intelligible, I have compiled a general map of this section of Alaska, showing accurately the relative positions of the most important districts where valuable deposits of minerals have been discovered (page 819). Upon inspection of this map, it will be observed that the chief metalliferous belt in this mineral field is in close proximity to the mainland shore, the trend of which it follows for more than a hundred miles in a northwest and southeast course, while the mineral croppings on the adjoining islands are much shorter in extent, and more irregular with respect to their strike and continuity. This principal metalliferous zone, which I will call the main-land system of lodes, contains gold, silver and lead, besides traces of copper, zinc and iron, gold being found extensively in a free state and also associated with sulphur, and with many of the sulphides of iron, lead and other substances. On the line of this belt, as shown on the map, there are a number of distinct mineral districts. Beginning at the southerly extremity, they are named as follows: Sumdum, Snettishham, Grindstone Creek, Sheep Creek, Gold Creek, Lemon Creek, Montana Creek and Berners Bay districts, each deriving its name from the hay or creek on which it is situated. Harris mining district, as legally organized under the local customs, rules and regulations adopted by the miners of Juneau, embraces, within its exterior boundaries, Grindstone, Sheep, Gold and Lemon Creeks, and all of Douglas Island. The limits of this immense metalliferous horizon are becoming definitely known through the exposures made by prospectors. The belt, as now recognized, varies in width from one to several miles, the lateral measurement being greatest at Juneau in Harris district, where the famous Treadwell mine, with its slate foot-wall, marks the westerly boundary of the zone, while the eastern side of Silver Bow Basin, with a granite hanging-wall, defines its easterly border.

Jan 1, 1893

By James A. Barr

PUMICE and pumice are varieties of volcanic ejecta formed from lavas of the more silicic types. Chemical analyses of pumice, pumicite and perlite, from which synthetic pumice is now produced, will generally fall within the limits 65 to 75 pct silica, 9 to 20 pct alumina, less than 8 pct combined alkalies (sodium and potassium oxides), less than 3 pct calcium and magnesium oxide, less than 3 pct iron oxide, with smaller amounts of manganese, titanium, phosphorus and other oxides. Perlite is characterized chemically by having, in addition to the percentages of oxides given above, as high as 6 pct combined water. PROPERTIES Pumice is a natural silicic foam glass produced by volcanic eruptions. The molten glass foam, upon rapid cooling, trapped the steam and volcanic gases that caused it to remain extremely porous and vesicular in structure. Pumice is found in the form of large lumps several cubic feet in volume and also in grains only a few millimeters in diameter. Chemically, pumicite is of the same range of composition as pumice. The distinction between pumice and pumicite is one of particle size; the coarser materials are pumice; the fine particles, an appreciable percentage of which is in the range of 100 to 325-mesh or finer, are pumicite. If the erupting volcano ejects a silicic lava containing much gas and water vapor, the sudden release of pressure tends to free the gas. The viscosity of the lava, its rate of cooling and the amount of gas evolved, all have part in determining the degree of expansion of the glassy particles and the fineness of the vesicle. If the lava is of the correct viscosity and there is not too much gas, a pumice may be formed. Large amounts of gas may cause complete disruption into pumicite.30 In 1916, Barbour gave the name "pumicite" to the volcanic ash of Nebraska and since then the name has been widely used in industrial circles for the finer-grained commercial varieties. The glass of pumice and pumicite is transparent and colorless. It

Jan 1, 1949

By Owen Rice

CHANGES in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. Soft coke is a great hindrance to proper blast-furnace operation and changes in coke hardness affect the working of the furnace. The best method of determining the hardness of coke is by using a combination tumbler-ball-mill. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged. An increase of this ratio improves the hardness of the resulting coke. WHAT IS GOOD COKE? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide, has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving

Jan 1, 1921

By Edgar L. Newhouse

The lead smeltery at East Helena, Mont., controlled by the American Smelting & Refining Co. since 1899, has been in continuous operation for the past 25 years. Most of the old smelting and roasting practices have been superseded by newer and more modern methods, but on account of the difficulties involved in changing the original construction, some of the methods in use of handling materials are not the most modern. This plant, however, is particularly interesting as being one of the few essentially lead smelteries in the United States. At Federal, Ill., Collins-ville, Herculaneum, and possibly other places, similar work is being done, but it is doubtful whether any of them produces as much lead as the East Helena plant, whose monthly production averages 6,500 tons. The situation, 5 miles east of Helena, is convenient to both the Great Northern and Northern Pacific railroads, while the electric power is obtained from Canyon Ferry, 12 miles east on the Missouri river. Local quarries supply the requisite amount of lime rock, which the contracts require to be crushed to 5 in. Of the 450 men on the monthly pay roll, a census showed 200 Austrians, 110 Americans, and 30 Italians, the balance being made up of miscellaneous nationalities. The ore supply is mainly derived from the Coeur d'Alene mines in Idaho, and consists of crude ore, coarse and fine concentrates, middlings, and slimes. About one-half of the total output of the Coeur d'Alene camp is sent to East Helena. An average analysis of these ores gives approximately 40 per cent. lead and 11 per cent. sulphur. Local shipments, varying from month to month, are mostly highly siliceous gold and silver ores carrying little lead. Small shippers, leasers of old mines, and prospectors are very numerous throughout Montana, and it is the policy of the company to encourage these men by every possible means, including the free sampling and analysis of their ores and aid in the development of their mines and prospects, whenever their results show promise.

Jan 1, 1915