Search Documents

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By A. D. Schwope, L. R. Jackson, K. F. Smith

Burghoff and Blank1 have pointed out that the creep properties of hard-drawn coppers are closely associated with their individual softening characteristics and have further shown that the creep resistance of various types of copper is improved, under certain circumstances, by cold stretching. In the design of certain types of electrical machinery, it is important to have the creep resistance as high as possible; furthermore, short-time creep strength is important since in many cases stresses are large only during warming-up and cooling-down periods. In this paper, data are presented showing the effect of cold work on the short time creep strengths of various types of commercial copper under several conditions. It is shown that trends from short-time creep tests are evident at longer times. Materials Used in the Investigation The coppers used in this investigation were commercial grade and of two basic types, oxygen free high conductivity (OFHC) and tough pitch. Additions of silver in amounts of 15 and 25 oz per ton were added to each of the two coppers. The analyses of these six coppers are given in Table 1. Originally, they started as wire bars 4 X 4 X 54 in. A. square rod was made by hot rolling the wire bars to 9/16-in. rod in 8 passes. This rod was then cold drawn to 0.445-in.-diam rod and annealed for 3 1/2 hr at 1000°F. It was then cold drawn to 0.325-in. rod and again annealed at 1000°F for 3 1/2 hr. Hard square rods were then made by cold rolling to 0.257 X 0.257-in. rod. Soft wire was made from the hard- drawn material by annealing at 650°F for 3 hr. The final rolling was performed using a set of 9-in. grooved rolls revolving at 30 rpm, which produced square wires. Reductions of approximately 5, 20, 30, and 40 pct were obtained using several passes in the same direction for the large reductions. The 5 pct reduction by drawing was accomplished using a steel die having 2 parallel bearing surfaces. The die angle was 7 1/2 degrees and the wires were lubricated with a paste of ceresin wax dissolved in carbon tetrachloride. The speed of drawing was 13 fpm. Since work was done on only two sides of the wire simultaneously, it was necessary to rotate it 90 degrees each pass to insure uniform deformation. The room-temperature tensile properties of the various tempers are given in Table 2. The grain size of the an- nealed 0.257-in. wires was uniform and averaged about 0.035-0.045 mm. Experimental Procedures for Short-time Creep Tests Standard creep-test frames (Fig 1) were used for the testing. Special fixtures were designed to apply axial compressive and tensile loads to the copper wires. The compression specimens were 1 in. long and the ends were ground flat and parallel. The creep in compression was indicated by the movement of reference marks s-ratched on intersliding platinum strips attached to the moving heads of the fixture. The movement was measured with an optical micrometer fitted with a filar eyepiece on which the smallest division was 0.00005 in. The tensile creep specirriens were 4 in. long which provided ample gripping surface for the jaw-type grips. The platinum strips were attached to a one-inch gauge length of the wire and the creep measured as previously described. The single-specimen furnaces were connected to individual power and control sources. The controlling equipment consisted of Foxboro controllers

Jan 1, 1950

By Joseph E. Pogue

Price is a complicated concept, for price is both a cause and an effect. This reciprocal aspect is commonly overlooked and the oversight is the source of many economic maladjustments. Price is the resultant of the ratio between supply and demand, but it differs from a mathematical concept of a proportion, by itself constituting an economic force which continuously alters the elements that determine the relationship. Price, therefore, is not merely the outcome of other forces but is in its own right one of the most powerful of economic agents. Price accordingly does not play a passive role; nor can it be sterilized or rendered inactive. In consequence, price cannot be fixed or at least kept fixed, except by the elimination of all freedom of choice on the part of producers and consumers. A primary objective of all economic activity is equilibrium. The same is true of a unit of economic activity, the single industry. The plane upon which equilibrium centers may shift in the course of time, but equilibrium itself is the point of departure and the point of return. If an industry is in equilibrium, that industry is operating effectively. The motivating forces of an industry—profits or the common good—are not to be confused with the prerequisite of equilibrium, but this mistake is often made. The producer is dominated by the profit motive; the consumer, or his collective representative, by the general welfare motive. No one is the advocate for equilibrium; that status is supposed to be arrived at automatically. If the forces of competition are perfectly free, such is the tendency. Equilibrium For the purposes of this analysis, equilibrium needs to be broadly defined and is conceived to involve: (1) balance between supply and demand; (2) internal equipoise amongst the elements within an industry; and (3) symmetry in respect to the whole economy. This definition implies flexibility and case of adjustment; a ready accommodation to change. Equilibrium does not postulate profits or nonprofits, social objectives or the lack of them. A decadent industry may be in equilib-

Jan 1, 1937

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By T. V. Philip, R. E. Lenhart

When commercial silicon iron sheets of varying magnetic quality are isothermally annealed at high temperatures, extremely large grains develop in the material having good magnetic properties. These grains are of the (110) [001] orientation and are formed by secondary recrystallization. The primary driving force for this secondary recrystallization is grain boundary free energy. For the secondary grains, activation energies of 103 kcal per mole for nucleation, and of 75.5 kcal per mole for growth, were obtained. The activation energy for nucleation of the secondary grains is consistent with a model involving redistribution of a precipitate acting as the primary grain growth inhibitor. SINGLY oriented silicon iron sheet was first produced in 1935.1 The material as commercially produced today has a very highly developed preferred orientation or texture; up to 95 pct of the grains are crystallographically oriented with their (110) planes in the plane of the sheet and their [loo] directions parallel to the rolling direction. This texture, usually written as (110) [00l], is referred to as the "GOSS" or the "cube-on-edge" texture. Because the magnetic properties of this material are superior to those of the nonoriented sheets in the direction of rolling, the oriented silicon iron has acquired tremendous industrial importance especially in the manufacture of transformer cores and other electrical equipment. The commercially produced material is essentially an iron-silicon alloy containing about 3 1/4 pct Si with minor impurities totaling less than 0.15 pct. The silicon steel heat is melted in the open hearth or electric furnace. The ingots are hot rolled, with or without being slabbed, to strips of 0.100 to 0.080 in. thickness. They are then cold reduced to an intermediate thickness, recrystallized, cold reduced to final thickness, decarburized, and finally annealed at a high temperature. During this high-temperature anneal, extremely large grains with the cube-on-edge texture are produced in the sheet. Several papers have appeared in the literature2-10 relating to the production of the Goss-textured material. Most of these describe the textures produced on cold rolling and on subsequent annealing of single crystal or polycrystalline silicon iron. May and Turnbull11,12 have recently shown the necessity of a second-phase dispersed impurity in the material for the production of the Goss texture. However, none of these papers describes in detail the nucleation and growth kinetics of the (110) [001] grains during the final high-temperature anneal.* The present work, therefore, is an attempt to understand the nucleation and growth kinetics of the cube-on-edge grains in the silicon iron sheet during the final high-temperature anneal.

Jan 1, 1962

By Louise Barton Freeman, Iley B. Browning, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By Iley B. Browning, Louise Barton Freeman, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By E. E. Donath, W. L. Crentz, J. D. Doherty

The principal washing problems in preparing coal for the synthetic fuel industry may be stated as: (1) ash removal for the Bergius process; and (2) sulphur removal for the Fischer-Tropsch process. A study is made of the effect of ash on oil losses during the elimination of the nonliquefiable portions of the coal in the hydrogenation process. The oil loss increases with ash content and results in increased consumption of coal, hydrogen, and power.

Jan 4, 1950

By J. G. Mravec

The SO-called gas-tube method as developed by Hare, Peterson and Soler for determining the type and content of gases in molten steel is particularly adapted for determining the hydrogen content in molten steel. The development of this method has been quite completely discussed in a paper published by these co-workers in 1937.' The purpose of this paper, therefore, is to familiarize with this method those who arc not well acquainted with it. The principle of the gas-tube method is as fol1ows: One end of an evacuated gas tube is sealed with a very thin copper disk. when this end of the tube is immersed in a test spoonful of molten steel, the copper disk melts almost immediately, allowing a portion of the steel to be drawn up into the evacuated space. Any dissolved gases, and those produced by reactions between the components of the steel during freezing, are liberated into the unfilled portion of the sampling tube. A blob of steel that forms on the immersed end of the tube after the sample is drawn up seals up the end, making it airtight again. The evolved gases are subsequently drawn out of the gas tube through a suitable valve and analyzed by means of an Orsat apparatus. The volume of the sampling tube is sufficiently large so that a pressure considerably below atmospheric is produced after the gas evolution. The low pressure is necessary to effect a nearly complete removal of gases from the steel. Construction oF Sampling Tube The sampling gas-tube apparatus is illustrated in Fig. I. Seamless S.A.E. tubing used for section A is first cut into 7-ft. lengths. Through cxperiencc it was found necessary to use two sizes of tubing for this part, "is-in. and 3/4-in., respectively. The smaller tubing is generally used on the hotter or lower carbon steels. If the inside wall of the tube A is coated with grease or oil, it should be burned out before being machined as follows: One end is machined on the inside diameter to a depth of 34 in., so as to form a seat for a 7/8-in copper disk, which is stamped out from 0.005 to 0.007-in. thick copper sheet. The other end is machined on the outside diameter to a diameter of 1 5/16 in., to take a small reservoir or trap member I?. About 4 in. below the same end, a 1/2-in. hole is drilled to receive the 1/2-in. copper tubing leading to the large reservoir C. The inside of tube A is then thoroughly cleaned with a round wire brush, such as is generally used to clean out shotgun barrels. It is very important that the surface be absolutely free of rust or any nonmetallic coating. Next, the thin copper disk is soldered in place with low-melting silver solder.

Jan 1, 1945

By M. E. Wadsworth, J. S. Cho

Colloidal silica dissolved in aqueous suspensions of high surface area thoria was permitted to adsorb on the thoria surface. Silica in three forms was identified by means of infrared spectroscopy and characterized by Si-O vibrational modes in the 9.0 to 10.5 region. A band at 9. 1 was attributed to free unad-sorbed silica, while adsorbed silica resulted in bands of greatest absorbency at 9.4 or 10.3p, depending upon the character of the surface bonding. Size considerations, the amount of silica adsorbed, and the character of the infrared spectrum for strongly adsorbed silica has been interpreted as evidence of formation of chain or layer silica linkages on the thoria surface. Infrared spectroscopy has been used successfully in recent years for the identification of minerals and synthetic inorganic substances. Unfortunately, infrared studies of silicate minerals have not proceeded to the point that unambiguous assignments may be made for Si-O vibrational modes as affected by lattice substitutions and structures. Several investigators have presented infrared spectra of silicate minerals, 1,7 and their work has pointed to the potential value of infrared to identify minerals as well as to note the sensitivity of various Si-O modes to structural and substitutional environments. The strong infrared absorption of various Si-O vibrational modes makes the infrared method a very useful tool for the study of silica adsorbed on the surface of solids of high surface area. Spaepen et a18 studied the adsorption of silica on thoria surfaces from aqueous solutions of silicic acid up to 300°C. A general review of the application of the infrared method to the study of surface adsorption has been presented by Pliskin and Eischens.9 EXPERIMENTAL Du Pont colloidal silica, Ludox SM (16.36% SiO2) and Ludox HS (30.25% SiO2) in aqueous suspensions were used as the sources of silica for the adsorption studies. The thoria used for this study was supplied by Union Carbide Nuclear Co.* under the preparation *Chemical Technology Div., Union Carbide Nuclear Co., Oak Ridge, Tenn. . number D-16-650. It was fired from the oxalate at 650°C and had a surface area of 32.4 ± 0.6 m2 per g measured by nitrogen adsorption. The chemical analysis of the D-16 thoria in ppm was: CO3= (5500), NO3- (< 4), so4±PO4 (100), and Si (20). The Ludox silica was placed in contact with the thoria in a two-liter autoclave10 between room temperature and 250°C. Slurries were made by placing 1 g of thoria in one liter of distilled water containing various additions of the silica sol. Samples were removed from the autoclave by opening a small stainless steel valve. Extracted samples were centrifuged for 10 min and excess solution was decanted. The sample was then dried for several hours at 80°C. Infrared samples were prepared by thoroughly mixing 10 mg of the thoria with 400 mg KBr in polystyrene vials on a "Wig-L-Bug" amalgamator. Pellets were pressed under vacuum and had final dimensions of 1.2 cm diam and 1.2 mm thick. Infrared spectra were

Jan 1, 1963

Jan. 7, 1952, AIME, Boston Section, Massachusetts Institute of Technology, Campus Room, Graduate House, Cambridge, Mass. Jan. 8, Society for Applied Spectroscopy, 6 pm, supper, Tosca&apos;s; 8 pm, meeting, Socony-Vacuum Training Center, 63 Park Row, New York. Jan. 9, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Jan. 13-15, Institute of Scrap Iron & Steel, Waldorf-Astoria, New York. Jan. 14-1.6, AIME, Minnesota Section, Hotel Duluth, Minn. Jan. 14-18, SAE, annual meeting, Hotel Book-Cadillac, Detroit. Jan. 1.6-18, Society of Plastic Engineers, Inc., annual national technical conference, Edgewater Beach Hotel, Chicago. Jan. 17, AIME, New York Section, Mining Club, 33 Broadway, New York. Jan. 1.7, AIME, Utah Section, Newhouse Hotel, Salt Lake City.

Jan 1, 1952

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff&apos; have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

J. C. WRIGHT.-The problem of organizing and maintaining a vocational class for those employees who are engaged in the mining industry depends on several most important factors. The first is the sympathetic cooperation of employer and employee; the second is to find the subject matter that must be presented to these men; and the third is to find the instructor who can present that subject matter. This is perhaps the most difficult, for we usually find a man who knows the material that is to be presented but is not a teacher or does not know how to organize his material. The man must know the subject matter from the standpoint of absolute contact with industry in order to be a successful teacher. I have come into contact with two kinds of schools organized in connection with mining occupations. In one type the instruction leans very largely toward elementary subjects, arithmetic, reading and writing and spelling; it is not of such a character as to help or improve the working man in his occupation in the sense that we are attempting when we speak of vocational education. In the other type of school, an engineer is usually employed as a teacher. He immediately begins to give the things with which he is most familiar and the instruction becomes such as only those who possess a high-school or college education, perhaps, are able to receive. In between these two schools is the school we are trying to, promote, a school that will meet the needs of those employed. MARGUERITE W. JORDAN,* Altoona, Pa. -Vocational education has become the business man&apos;s problem; for he is the keeper of that white elephant, labor turnover, and anything that will decrease the size of the monster is worthy of serious consideration. This vocational education can do; for it can supply many of those deficiencies in upbringing and. environment that make for the discontent and restlessness of our varied classes of unskilled labor: the Anglo-Saxon mountaineer; the Southern negroes who have crossed Mason & Dixon&apos;s line by the thousands, "searching satisfaction for our minds;" and the still greater number who have sought across the sea America, "the promised land.

Jan 4, 1919

By F. W. Smith

Within the Northern Pennine Orefield, England, intersections of fluorite veins are generally richest in ore, and their recognition enables investigation of the ore potential of the intersecting bodies. A method, based on routine analysis of fluorite for yttrium, has been used with success in mines of the district to predict the location of intersections in partially developed fluorite-bearing ore bodies. This short note is intended as a brief introduction; the details of United Kingdom applications are to be published at a later date. Geology The Northern Pennine Orefield is the second largest fluorspar-producing region in Britain. The associated minerals galena, sphalerite, chalcopyrite, barite, and witherite have all been extensively worked in the past but, with the exception of a single barytes mine, all of these operations are now abandoned. Galena alone is recovered as a byproduct of fluorspar beneficiation. At the present time two companies are producing about 38,000 tpy of fluorspar from high grade vein ore bodies, and a number of concerns are actively prospecting in old lead workings. The mineralization is localized in veins and replacement flats within favorable lithologies in an alternating limestone, sandstone, shale sequence. Since the thickness of individual beds is not great (generally less than 20 m), vein bodies tend to be ribbon-shaped, with length greatly exceeding width and height (Dunham). They thus present difficult exploration targets for conventional diamond drilling techniques. Ore grade varies greatly along the veins, which can change rapidly in character from mineral stained fault gouge to massive mineral bodies up to 10 m in width. It has been known for a very long time that the richer ore bodies tend to be associated with vein intersections in favorable beds. It is assumed that vein fissure intersections provided vertical channelways through which hot ore-bearing brines were able to ascend from deeper cavities in the sequence. Thus investigation of intersections at other horizons generally yields further ore bodies. Technique The relative concentration of yttrium in fluorite is a good indicator, in the North Pennines, of the direction of flow of mineralizing fluids. In all of the ore bodies so far studied in detail in this region, the concentration of yttrium increases markedly in the direction of vein intersections that are believed to have acted as feeder zones to the remainder of the bodies. The reason for this relationship is probably connected with the degradation of soluble rare earths-fluoride complexes by the changes in various physicochemical parameters of the hydrothermal fluids as they entered the ore body cavities from the feeder zones. The simultaneous release of free fluoride ions also contributed to the increased ore values in these intersection zones. Yttrium values in fluorite taken from a longitudinal traverse of the western ore body, Redburn mine, Rookhope, are plotted in [Fig. 1.] The position of a major vein branch and three cross veins are clearly indicated by yttrium maxima. The cross veins themselves contain up to 2.5 m of low grade fluorspar ore. The exact positions of B and C were unknown previous to the geochemical survey. Similar results have been obtained for several other veins and ore bodies in the area. Clean fluorspar was collected as bulk samples from within 300 mm of the vein wall and, since the vein infilling is simple, with mineral growth from the walls inward, analyses of the samples are considered comparable along the length of the ore body. A number of samples taken from the center of the vein show a

Jan 1, 1975

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960

By W. W. Krysko

In order to calculate the critical particle size of lead oxide entrapped in lead, Stoke&apos;s Formula may be applied. All data were available except figures for the density of lead oxide at elevated temperatwes. The density of lead oxide was determined by means of dilatometmetrc and volumetric methods up to 1010°C. Graphs of the density of lead and lead oxide as well as the viscosity of lead are given and discussed, with the conclusion that the most unfavorable region for the separation of lead oxide from molten lead lies just above the melting point of lead. DURING previous investigations, particularly on the dedrossing of lead with aluminum1 and the oxygen solubility in lead,&apos; the critical particle size of lead oxide which could be entrapped in solidifying lead was estimated by calculation, and it was shown that high values found for the oxygen content of lead may be due to the method of sampling and the entrapped particles of dross. Unfortunately, due to lack of data, an exact mathematical solution was not possible. The particle size which will separate under a given condition can be estimated from Stoke&apos;s Law, which states that where: d = diameter of the critical particle size ¦q = viscosity of lead in Poise V = constant velocity in cm sec-I g = 981 cm sec-2 61= specific gravity of lead 62= specific gravity of lead oxide The depth of the lead bath and the time before solidifying define the velocity. The viscosity of molten lead is known from earlier work by Krysko and is given in Table I. The specific gravity of lead is also known, see Table II. These values are according to Hofmann. A careful survey of literature revealed no values for the density of lead oxide at elevated temperatures. The present investigation was therefore conducted to provide this information. RESEARCH INVESTIGATIONS The density of lead oxide was determined from the following experiments: 1) Determination of the density of lead oxide at room temperature. 2) Dilatometric investigations on the same samples. 3) Determination of the shrinkage at the liquid-solid trans£ormation. 4) Density determinations on liquid lead oxide. 5) Time temperature curves during cooling. 1) The samples for the determination of the density of lead oxide in the solid state were prepared in the following manner. Molten lead oxide was cast into I hot mold which could be opened along the longitudinal (vertical) axis. The cast samples were cylinders of approximately 10 mm diam and approximately 80 mm length. The cylindrical hot mold was open at both ends and was placed on a large copper chill plate shortly before casting. The solidification of the lead oxides proceeded upwards without any formation of internal cavities. The sample was carefully checked with respect to density and crystalline appearance, and only the lower portions which were crystalline and free from porosity were used. The density was determined in a specially made pyknometer-like container, where the surplus liquid was squeezed out through an orifice approximately 1/10 mm in diameter. Mercury or water was used as the liquid. The densities of the samples were calculated from the weight, volume, and mean specific gravity of eight samples was 9.62 * 0.05 g cm"3 at 22"~. 2) The samples were machined to approximately 1 1/2 in. in length and fitted into a dilatometer. A

Jan 1, 1962

By Thomas L. Garwood, F. C. Menk

IT is generally, accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segr6gate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of .coal in handling and shooting in the mine gives this small-size coal good

Jan 1, 1943

By R. C. Buehl, J. P. Morris

F. D. Richardson—The authors are to be congratulated on this further contribution to our knowledge of the thermodynamics of the interaction between sulphur and carbon and silicon in liquid iron. As the authors state, the influence of carbon and silicon on the activity coefficient of sulphur in liquid iron is clearly of great importance in the blast furnace, since it must cause a three to fourfold improvement in the partition of sulphur between slag and metal. The influence of increasing temperature in further increasing the activity coefficient of the sulphur in the metal in the blast furnace by increasing the carbon content is also of interest. This effect, however, is probably only part of the reason for the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing temperature. Other contributing factors are the lowering of the oxygen potential in the presence of carbon by increasing temperature and the probable increase in the activity coefficient of the lime in the slag for the same reason. The former of these effects, which works via the (CaO) + [S] = (CaS) + [O] equilibrium, might possibly account for a 70 pct improvement in the sulphur partition and the latter might give a further 50 pct improvement. C. Sherman—I would like to compliment the authors on their very careful research. If I may, I would like to show results of calculations on the carbon-sulphur-iron system similar to the ones that were shown in our paper for the silicon-sulphur-iron system. For Fe-S-C ternary system k=PHgs/PH2 x 1/(f1°) (f2°) (%S) where fs = sulphur activity coefficient fs&apos; = fs for Fe-S system of equal pct S f3° = f2/f2 for Fe-S-C ternary system This same analysis has been used on other systems, but the results shown in fie.- 7 are for carbon and silicon. L. S. Darken—I would like to make two brief comments in addition to complimenting the authors on an apparently very precise and accurate investigation. The first is that the present work is in agreement with a calculation by Larsen and myself." Our calculation (much less precise than the present work) was based on: (1) Unpublished work on the sulphur content of molten iron (1.5 pct at 1500°C) in equilibrium with graphite and an iron sulphide slag; (2) the distribution coefficient of sulphur between slag and carbon-free liquid iron. We expressed the result in a form equivalent to log 7. = 0.18 [%C] which gives an activity coefficient (?s.) of sulphur only slightly higher than the authors find and certainly within the precision of the earlier work. My second comment concerns the correlation of the thermodynamic findings with atomistics. A rough pic- ture of the atomic arrangement in the liquid solution is rather easily conceived for this particular liquid solution containing iron, carbon, and sulphur. Carbon has a very much stronger affinity for iron than for sulphur. Hence we may conclude that a sulphur atom will but seldom be adjacent to a carbon atom—since this would be a position of high energy. From the metallic radii of iron and carbon we know that six iron atoms pack neatly around one carbon atom. Thus each carbon atom in retaining this shell of iron atoms (which latter may not be replaced by sulphur on account of the high energy requirement) decreases the available positions for each sulphur atom by six. Hence each atomic percent of carbon decreases the equilibrium sulphur content by 6 pct (of itself). Or, at low concentration each atomic percent of carbon increases the activity coefficient of sulphur by 6 pct. This is in good agreement with the observed increase (6 or 7 pct at low carbon content). It is indeed gratifying to find a case where, by such simple reasoning, quantitative agreement is found between precise data and the modern picture of the atomistics of the metallic state. J. P. Morris (authors&apos; reply)—We would like to point out that there is an error in the equation on p. 322 of the paper. The third equation should read: ½S2 (gas) + H2 (gas) = H2S (gas) The authors wish to thank everyone for the interest they have shown in the paper. In regard to the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing the temperature, Dr. Richardson is correct in stating that the cause can be attributed only in part to the increase in activity coefficient of sulphur resulting from the rise in carbon plus silicon content of the metal with rise in temperature. However, this factor is probably an important one. The results of one experiment, performed since this report was written, indicate that at a constant temperature the addition of silicon to a melt saturated with carbon causes an increase in the activity coefficient of sulphur even though the carbon solubility is lowered. In this test, 2.5 pct silicon was added to a melt saturated with carbon and maintained at 1400°C. Although the carbon content dropped from 4.85 to 4.1 pct, the activity coefficient of sulphur was increased by about 20 pct.

Jan 1, 1951

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.&apos; As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.&apos; Other investigators have also studied the binary systems Ti-Cr,3-7&apos; Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954

By H. C. Brown

SINCE 1934 the steel industry has been utilizing the spectrograph for supplementing wet chemical analysis in the production control of electric and open hearth furnaces. This means of control made great strides during the war years because of the general acceptance of the spectrograph and the increased emphasis that was placed on rapid control methods. However, in the post war era, with the demand still on increased production, it became apparent that a still more rapid and economical means of production control was needed. Since the spectrograph had been used mostly in the analysis of low alloying and residual elements, it also became apparent that equipment was needed to extend the spectrographic technique to the analysis of the high alloying elements in stainless steel. For these reasons, companies manufacturing spectrographic equipment were prompted to start development work on direct reading instruments. In June 1949, the Applied Research Laboratories of Glendale, Calif., announced that a direct method of spectrochemical analysis for stainless type steels had been developed. This paper will describe the use of the Applied Research Laboratories Production Control Quantometer in the quantitative control of stainless, silicon, and plain carbon steels being made at the Butler Pennsylvania Div. of the Armco Steel Corp. The Armco Butler Div. has one 70-ton electric furnace and six 150-ton open hearth furnaces. The electric furnace is employed in the making of all types of stainless steel and the open hearth furnaces are used for the production of silicon, wheel, and plain carbon steels. The ARL quantometer was purchased primarily for the purpose of controlling the steelmaking in the electric furnace, but its use has been extended for the analysis of final tests (ladle tests) on a number of different types of stainless, silicon, and plain carbon steels. Because of this additional work by the quantometer, substantial savings in manpower and time have been realized by the laboratory. In the analysis of a set of preliminary tests from the stainless steel furnace, approximately 40 min in laboratory time are saved due to quantometric analyses. Despite the fact that more specialty grades of stainless steel are being made in the electric furnace, the average tons per hour have been increased since the quantometer was put into operation. Specialty grades require more furnace time than regular commodity grades of stainless steel. The installation of the ARL production control quantometer was completed on March 13, 1952. By May 1, 1952, the instrument was calibrated for nickel, chromium, manganese, silicon, and molybdenum, which are the elements necessary for the production control of the stainless steel furnace. Within the following month, training of personnel on the quantometer was achieved and a study of the accuracy of the instrument showed that the results obtained were sufficiently accurate for control purposes. Therefore, on June 11, 1952, the quantometer was placed on production control for all types of stainless steels. Starting September 11, 1952, the instrument was gradually placed on ladle analysis (final tests) as the analytical curves were refined and additional curves were drawn. The quantometer has been relatively free of breakdowns since placing it on production control. The samples from only one stainless steel heat have had to be analyzed by wet chemistry because of instrument trouble. The previously existing heat-time record was also bettered by 15 min on a commodity grade of 18-8 stainless steel. Scope of Control In general, the quantometer determines all elements necessary for the production control of all types of stainless steel heats and for the ladle analysis of various types of stainless steel heats. It is also used in reporting final results for silicon, manganese, chromium, nickel, molybdenum, tin, copper, and aluminum on all silicon steel grades and manganese, chromium, nickel, molybdenum, tin, and copper on several plain carbon steel grades. Table I shows the elements and the concentration ranges of these elements in the various types of stainless, silicon, and plain carbon steel that are determined on the quantometer. A study of the results obtained on ladle test samples of stainless steel types 410, 430, 430 Ti, 446, 301, 302, 304, 304L, 305, and 17-7 PH will be discussed. Also included in the study are the results obtained on ladle test samples of a number of silicon steels. Apparatus In order to take full advantage of the potentials of the production control quantometer, the unit has been placed in an air-conditioned room with relative humidity control. The temperature is maintained at 73&apos;22°F and the humidity at 45&5 pct. The air conditioning serves as a precaution to minimize the amount of adjustment and calibration needed during operation. It also reduces contaminating fumes and dust and thereby lessens the necessity for maintenance on the equipment. The quantometer is composed of three units: the high precision multisource unit, the 1.5 meter vertical spectrometer, and the console. The source unit supplies excitation conditions varying from spark-like discharges to arc-like discharges. The voltage to the source unit is supplied by a motor-generator

Jan 1, 1955