Search Documents

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947

By Henry Fernald

THE accounting system or bookkeeping methods of any company are principally the concern of that company and of those who are in control of its affairs. Its published financial report is, however, primarily intended for those who are not already fully informed regarding its operations and finances. Whatever may be the advantages of standardization of accounting and bookkeeping methods, it must be admitted that a company has a certain right to handle its accounts and keep its books and records in whatever manner may seem to it best adapted to its affairs, even though such methods may differ materially from those generally adopted by others. In its financial reports it should not, however, either ask or expect that the statements it makes or the terms which it uses will be given in its case a meaning and interpretation different from that which they are ordinarily considered to have in similar reports and statements of other companies. The particular form and arrangement of such reports is a matter concerning which there may be much difference of opinion. It is of little importance whether current assets come first or last in the Balance Sheet, but it is important that there should not be included under this designation any items which are not properly current assets within the generally accepted meaning of that term. The extent to which stockholders or others interested are to be made acquainted with the full details of a company's business is a question which the proper authorities must in each case decide. It should, however, be recognized that there are certain facts regarding a mining com-pany which must be set forth in a financial statement if it is fully to cover the conditions and affairs of the company. For example, a financial, statement which does not include or is not accompanied by a statement, of the ore reserves of the company does not fully set forth its financial condition. This is true whether the absence of such a statement of ore reserves is because it is not desired to make public the figures or whether it is because the ore reserves themselves are not definitely known, or accurately measured.

Jan 1, 1928

By William Carton, Cyril U. Cooledge

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By Cyril U. Cooledge, William Carton

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. S. Simons, G. Major-Marothy, M. A. K. Grice, D. A. Dahlstrom

The vacuum filter operating variables that influence cake moisture are discussed. The influence of temperature control, particularly through application of steam to the cake, is emphasized. Results of pilot plant studies on filtration of fine hematite concentrates are presented and discussed, and are shown to support the theoretically-derived conclusions. Results on fine magnetite concentrates are also used to support the argument. The relative merits of disc and drum filters from the standpoint of cake moisture are discussed. Moisture content has always been recognized as one of the most important properties of concentrates used as pellet plant feed. Most iron ore concentrates are produced by wet methods, and are finally de-watered on filters. Obviously, a real economic advantage accrues to the ability of control the moisture content of the filter cake within the range required for optimum pellet production. Another consideration, also, has been receiving increasing attention recently. Transoceanic shippers of concentrate cargoes are critically assessing the hazards of excess moisture. The nature and magnitude of these risks have been described, ' and it appears that their elimination may require that residual moisture be somewhat lower than the limit for proper pelletization. Coarse, very free-filtering materials, such as the products of spirals, are usually best handled on top-feed types of machines. The moisture content of the cake may be held at a specified value by proper design and operation, taking into account cake thickness, air-flow rate, and drainage time. Fine-grained concentrates, with which we will be concerned here, must be filtered on Drum or Agidisc machines. With many of these materials, it is possible, by proper design, to meet cake moisture requirements with a conventional filter station. The first installations to produce high-grade pellets from magnetic taconites fell in this class. In fact, the design criteria were developed in connection with operations of Reserve Mining Co. at Silver Bay, inn.,2 and these have been verified repeatedly in other mills. The trend today, however, is toward the production of more difficultly dewatered concentrates. This is due on the one hand to the increasing attention being given to non-magnetic ores, which tend to be far slimier, and therefore much more retentive of moisture, than the magnetites. On the other hand, the pressure to improve the grade of the magnetic ores is leading to finer grinds, which also are more difficult to dewater. In the latter case, the decision to improve grade in an existing operation by finer grinding for better liberation may lead to two unattractive alternatives: 1) substantially higher bentonite consumption, plus the risk of poorer quality pellets, from high cake moisture, or 2) installation of a thermal dryer. There is, however, a third alternative. In recent papers by two of the authors3,4 it was shown that for many materials a significant decrease in cake moisture can be obtained by applying live steam to the cake face during the drying part of the filter cycle. Further, this limited drying appears to have distinct economic advantages compared to thermal drying. It is the purpose of this paper to explore the third alternative. To do this, the results of an extensive pilot study of steam filtration of a hematite flotation concentrate will be critically examined. This study was sufficiently broad so that a number of alternate suggestions (besides steaming the cake) for reducing moisture content were tested, and comparative data for both Drum and Disc filters were obtained. The work was particularly interesting since the concentrate has a high Blaine surface, and is therefore particularly difficult to dewater to the levels required. FILTER CAKE MOISTURE The significant difference between concentrate filter cake as discharged from the filter, a cargo of that same filter cake during or after shipment, and a green ball formed from that filter cake is in the relative volume of voids, or porosity. In every case, the material is a collection of small solid particles held together by the cohesive forces of a liquid. The physical properties of the aggregate are determined by the

Jan 1, 1967

By Ray W. Arms

The combination wet and dry coal-cleaning process is not an attempt at a compromise between the wets and the drys nor is its merit confined entirely to the limitation of moisture in the smaller sizes. It is more correctly, and more broadly, an application of the sized-coal cleaning principle adapting itself in an ideal fashion to present day multiple-size preparation practice. The purpose of this paper, therefore, is to call attention to the broader significance of the term "combination wet and dry process" and to mention some of the factors that govern its application. In the narrow sense, when considered apart from the sized-coal cleaning principle, the combination process finds its justification chiefly in the ability to limit the moisture in cleaned coal. Larger sizes of coal offer less superficial area compared with their bulk for the attraction of moisture films. They drain more readily in bins or railroad cars, having more interstitial space for the free flow of water. Therefore, they neither attract nor hold objectionable moisture percentages. In fact, there is so keen a demand for certain washed sizes containing some moisture that hygroscopic salts such as calcium chloride are applied to attract and retain it. When coal deliveries are made on a guaranteed moisture percentage the coarser sizes may be washed and mixed back with the fines without adding greatly to the original moisture but the fines must be dry cleaned or dried to control moisture. Thus in all respects moisture in the coarser sizes is less objectionable than in the fines. The implication of this statement, that moisture is always more or less objectionable, is true. It is safe to say that if dry-cleaning apparatus could be perfected to a point at which its technical results, cost and other aspects would be equal to wet washing, water would no longer be used. As it is, we find that good technical results are more difficult to obtain by dry cleaning than by water. Obviously the use of air tables for coarse coal is not ideal, for it involves the attempt to stratify material in a thin bed on a table surface when the load is only one particle deep. Furthermore, the various air cleaning tables on large sizes require a large volume of air for separation, more power to operate, more dust-collecting apparatus and involve more coal breakage.

Jan 1, 1931

A self-appointed, committee consisting of J. Waldo Smith, Chairman, Richard S. Buck, J. J. Carty, J. Parke Channing, E. L. Corthell, Alfred Craven, Thomas Crimmins, Gano Dunn, George Gibbs, Alex. C. Humphreys, F. L. Hutchinson, Charles Warren Hunt, D. S. Jacobus, John W. Lieb, William Barclay Parsons, George H. Pegram, Charles F. Rand, Calvin W. Rice, Robert Ridgway, William L. Saunders, Merritt H. Smith, Bradley Stoughton, and William H. Wiley, organized a course of seven free lectures on military engineering, which were given by Captains Thomas M. Robins, Richard T. Coiner, Edward D. Ardery, Corps of Engineers, United States Army, and which was under direction of Major General Leonard Wood. The United Engineering Society presented, without charge, the use of the auditorium for the purpose of these lectures, but the interest proved to be more than three times as much as had been expected, and it was therefore necessary to divide the courses into three parts, one of which was given in the afternoon in the auditorium of the United Engineering Societies Building, one in the evening in the same place, and another in the evening in the auditorium of, the American Society of Civil Engineers. These lectures occurred on Mondays, from Feb. 14 to Mar. 27, 1916. The subjects and speakers were as follows: Feb. 14, 1916: Organization and Duties of Engineers in War, and what Engineers in Civil Life will be called upon to do in the Defence Of the United States. Captain Thomas M. Robins, Corps of Engineers. Feb. 21, 1916: The Service of Reconnaissance Including Surveying, Mapping and Sketching, Photography and Map Reproduction. Captain Richard T. Coiner.

Jan 5, 1916

By N. W. Lord

There hare been made at one or two places in Ohio, during the last year or two, some irons of rather unusual phosphorus-percentages. The first of these which I had occasion to examine came from Moxahala Furnace, in Perry county. The furnace was built originally to smelt an ore found in large deposits near its furnace in the " black band" horizon. The deposit was easily exposed by simple stripping;" it was from six to eight feet thick, being a blne carbonate ore, very free from silica. This ore yielded, on analysis, from two to 3 per cent. of phosphorus, when carefully sampled. The furnace company had trusted entirely to old analyses made on "outcrop" ore, well weathered, and received all other results with indifference. The result of the first run of the furnace was an iron in large whitish-gray crystals, and so brittle that it could be pulverized in a mortar. This iron contained 4.90 per cent. phosphorus. A limited quantity only was made, which was gradually disposed of as a great ('softener" to foundries. The Moxahala Furnace was subsequently run on Lake Superior ore mainly. The second case of such iron occurred last summer at Mt. Vernon Furnace. A deposit of what was locally known as "Hallelujah" ore, was opened for the furnace. This ore was a blue carbonate, similar to the first-described. The iron made was pure tin-white in color, and showed large crystals without a trace of the grain of ordinary pig-iron. It was sopposed at the furnace to be spiegeleisen, and was sent to me to be

Jan 1, 1884

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge.. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By F. Louis Grammer

The difference between blast-furnace gas and ordinary producer-gas is chiefly that blast-furnace ga,s is higher in CO2 and lower in hydrocprbons and hydrogen, as is shown in Table I. Table I.— Volume-Composition of Producer-Gas and Blast-Furnace Gas. Producer-Gas. Blast-Furnace Gas. Per Cent. Per Cent. (Volume.) (Volume.) CO......22 to 33 25.5 CO2........ 6 to 3 13.0 H...13 to 7 1.5 CH4........ 3 to 1.5 0.0 N..54 to 60 60.0 If natural gas, water-gas, or by-product coke-oven gas be available, blast-furnace gas can be made to resemble very closely in calorific value the average producer-gas by merely mixing in one of these products, which are richer in hydrocarbons and hydrogen. Blast-furnace gas, however, possesses a virtue which is sometimes absent in producer-gas, especially with coals very high in sulphur—namely, that blast-furnace gas is relatively free from sulphur. In some regions the sulphur in coal is an acute problem, and it is highly desirable to find uses for the mine-products which are specially high in sulphur-content. An advantage would be gained if the coal were coked before charging into the gas-producers, but this adds to the expense. Sulphur may be partly eliminated from coal by washing it, the success depending upon the form in which the sulphur occurs, and upon the efficiency of the washer, but it cannot always be removed to the extent desired at most American plants. It is not practicable to remove all the sulphur from producer-gas by washing it, though Mr. Reinhardt, of Germany,

Jan 1, 1909

By Walter S. Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case 1 If compressed air is allowed to expand to the atmospheric pressure through an orifice in an sir line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. Cv Specific heat of air at constant volume, B.t.u. per lb. per deg. F. Cp Specific heat at constant pressure, B.t.u. per lb. per deg. F. T1 Absolute temperature of air in pipe, deg. F. T3 Absolute temperature of air outside after expansion and mixing and coming to rest. J Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By James Boyd

REACTIVE metals are not only those sufficiently radioactive to be used as fuels, such as uranium and thorium, but all metals that will find application in power reactors. It is required of such metals that they be relatively inert or chemically unreactive, dimensionally stable at high temperatures and pressures, and either very absorbent of radioactivity or transparent to it. To gain the right perspective concerning these metals it is necessary at this point to explode some erroneous concepts propounded so often they have become accepted as fact. The first of these is that the great industrial nations, especially the U. S., have reached their pre-eminent position chiefly because they possess abundant mineral resources. Some U. S. mineral economists, echoed by the politicians, have taken this position so often that many of their theories and policies are based on the presence of developed mineral resources as a sine qua non to the country's greatness. Actually the reverse is true- under a social and political system granting free rein to the initiative and creativeness of its people, many hidden mineral resources that otherwise would have lain fallow have been developed into productive enterprises to the benefit of the national industrial economy. Again, once the proper incentive was furnished, other countries have also been able to establish valuable mineral enterprises in recent years; resources long dormant for lack of a proper economic environment suddenly have become valuable and productive. It is possible to name immediately several nations where such domestic economic developments have had favorable repercussions within the last decade. The absence of productive mines in any country is no indication that workable deposits do not exist within its territory.

Jan 11, 1957

By G. E. Johnson

E. D. HYMAN*—How much sorting of scrap is done ? G. E. JOHNSON (author's reply)—We do practically no sorting. We charge "run of mine" scrap to the furnace. The unmeltables, mostly iron, are in such demand today that there is no difficulty in disposing of them. It may soon be desirable to sort out from the unmeltables as much of the brass as possible. J. J. BRUGMAN†—We have somewhat similar problems in the secondary aluminum business. What is your method of removing the unmelted material from the furnaces? Why have you such an apparently small space in which to charge your materials? Do you find that you have to seal that opening, or can you have it open and continuously charge at one end and pull out the other ? G. E. JOHNSON—Our means of melting scrap is efficient only to the extent that we use the waste heat from the vaporizing chamber to do the job. It is a batch process. We open the charge door and place the scrap on the hearth by hand shoveling. The door is then closed during the melting down period. After the melting is complete, the opposite door is opened and the unmeltables are raked out. The doors are approximately 3½ X 4½ ft and are not sealed during the process only closed. They are nominally tight. Some metal is oxidized in the process. We have visualized a means of conveying the materials through this melting unit with the metals that are melted trickling out during its travel. T. H. WELDON‡—Mr. Johnson, in line with the last question, is it necessary to seal the furnace between the melting down and the vaporizing unit, or have you got an inverted syphon in the bottom of the chamber? G. E. JOHNSON—That was one of the first things we encountered. We had to have a sealed opening, and it is a molten metal seal. You have indirectly asked me another question, which was: "Do you have to seal up the melting unit?" I would say we should exclude as much air as possible, although we are not too efficient in doing that. We allow the melting unit doors to be open when we charge and when we remove unmeltables. You can readily see that that would lead to the idea of having a controlled atmosphere in the melting unit, and I think this would do a more efficient job of melting the scrap. T. H. WELDON—How often do you charge the furnace? G. E. JOHNSON—We charge the melting unit, and rake out the unmeltables, about every hour. H. R. HANLEY*—Are any provisions made for controlling the rate of oxidation for the production of various size particles for certain characteristics of the zinc oxide product? G. E. JOHNSON—Yes, there are many. You are getting pretty much into the fine points of zinc oxide manufacture. Some of us still think we have something to learn about that. In general, this muffle furnace as I have described it to you produces a rounded particle of zinc oxide which is generally formed by a rapid oxidation of the zinc vapor, followed by rapid cooling. We have gone to the other extreme in some of our experiments. We have changed the furnace to produce a type of zinc oxide, such as we thought was peculiar to American process zinc oxide, by controlling the temperature at the point of oxidation and maintaining that temperature for a much longer period of time than we do when we make the rounded shape. There are other relationships that this furnace readily provides. One of the important factors is the ratio of air to zinc vapors. We can vary that by varying the air supply to the baghouse, or vary the rate at which we are vaporizing the zinc by the simple expedient of regulating the temperature over the carborundum arch. We have a number of variables that permit us to produce all of the grades of French process zinc oxide from lead-free up through the highest grades of seal oxides. There are many controls that we can apply to the operation. What I have said is but a brief condensation. K. MORGAN*—Can Mr. Johnson give us some idea of the fuel consumption of the furnace ? How much oil does he use per ton of zinc distilled? I am also interested to know what sort of heat transmission he gets through the arch? What is the thickness of the tiles used to construct the arch? Some time ago we built a small furnace for a different purpose, using a carborundum arch, and we found that the reflectivity of the molten zinc surface was so great we had to use a very high arch temperature. We found we made an improvement by having a layer of carbon on the surface of the zinc. Has Mr. Johnson had any experience on these points ? Does he make any sort of insolu-bles which he leaves in the furnace which he cannot tap out ? G. E. JOHNSON—I believe your first question was the fuel consumption. If I recall, somewhere in this paper there is a test that I quote. I believe we used 800 gal in a given period of time. Offhand I cannot translate that into tons of metal. I might also state that we have this understanding; that the carborundum arch, as the temperature becomes higher, becomes more efficient in heat transmission. As a matter of fact, I believe it is at about 2600°F or higher that the highest efficiency of heat transmission becomes available. We have calculations that I cannot quote from memory which indicate that the carborundum arch does a really very fine job for this type of furnace. Another point that we had considered was the fact that this furnace could be readily constructed so as to furnish an ideal source of heat for waste heat boilers. If a carborundum arch was used over the melting unit, we would have no zinc vapors in the gases at all— just clean combustion gases from which we would have removed some of the heat. L. P. DAVIDSON†— The insolubles

Jan 1, 1950

By Walter S. Weeks

The process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the JouleThompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. C, Specific heat of air at constant volume, B.t.u. per lb. per deg. F. C, Specific heat at constant pressure, B.t.u. per lb, per deg. F. T1 Absolute temperature of air in pipe, deg. F. T8 Absolute temperature of air outside after expansion and mixing and coming to rest. j Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By Joseph F. Oesterele, Richard S. McCaffery

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

By Richard S. McCaffery, Joseph F. Oesterele

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

By J. W. Spretnak, G. Sachs

The: iron-rich iron-nickel alloys have attracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are the base of many alloys with various outstanding properties. The iron-nickel alloys, therefore, have been investigated extensively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,l and will be discussed in some detail in the sections of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to 10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis," which is not dependent upon the rate of cooling and persists even with very slow rates of cooling.3 Honda4 and Merica4 have therefore resigned themselves to proposing a diagram (Fig. I) for practical use, illustrating the structural relations under commercial conditions instead of attempting to establish the true equilibrium diagram. Marsh is less pessimistic and suggests an equilibrium diagram (Fig. 2) which conforms approximately to the facts known about this system. Recent X-ray investigations by Owen-Sully5 and Bradley-Gold-schmidt6 on powdered alloys indicate that the previous work on the iron-nickel system yielded very incomplete results. These investigators agree (Figs. 3 and ,+) that alloys in the powdered form containing more than 8 per cent and up to about 35 per cent Ni decompose into a stable heterogeneous mix-

Jan 1, 1941