Search Documents

By James A. Crookston, William D. Fitzpatrick

Committee C-8 of the American Society for Testing and Materials defines "Refractories" as "Material, usually nonmetallic, used to withstand high temperature," and it defines the term "Refractoriness" thus, "In refractories the capability of maintaining the desired degree of chemical and physical identity at high temperatures and in the environment and conditions of use." The ability to withstand high temperatures is critical to classifying a material as a "refractory." However, as the foregoing definition of "refractoriness" implies, the refractory material may be subjected to and is expected to resist not only high temperatures but a variety of other destructive forces incident to its use. These include abrasion, impact, thermal shock, chemical attack, and high level loads at high temperatures. The various industrial applications of refractories represent an infinite variety of combinations and degrees of severity of these destructive forces, including high temperatures. Naturally, such a variety of application conditions leads to a need for a wide variety of refractory products to satisfy those conditions. The number of refractory products available is great enough that some form of classification is necessary to a discussion of refractories. Refractories may be classified in several ways, but the most suitable one is based on their general compositions and to lesser degrees on their physical condition and distinctive properties. The primary types of brick include aluminosilicate brick (fire clay and alumina), basic brick (magnesia and chrome ore, alone and in various combinations), silica brick, insulating brick, and special refractories (carbon, Sic, ZrO,, zircon, borides, and nitrides). Brick are, of course, preformed and are usually heat treated at high temperatures before use, but are in some instances unburned and/or chemically bonded, including the relatively new class of tar-bonded magnesia and/or dolomite brick. In addition to preformed refractories, another broad category includes the so-called specialty refractories, which are usually made in the same types as itemized for brick-bonding mortars and high temperature cements, hydraulic setting castables or refractory concrete, plastic firebrick, and ramming mixes. Refractory grains, such as fire clay and high alumina calcines, dead-burned magnesite and periclase, and dead-burned dolomite are also considered refractory products. Brick are also classified on the basis of physical dimensions, as standard sizes and special shapes. The standard sizes are those which are of definite shape and design and are designated as 9 x 4 ½ x 2 ½ in. and 9 x 4 ½ x 3 in. straights and series. All other brick of non- standard sizes are referred to as special shapes. These come about as a result of a particular need for a given furnace or for a particular application.

Jan 1, 1975

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Walter C. Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1 1/3 miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1938

By H. G. Dwyer

CONSIDERATION for future expansion influenced the design of the new smelter at Chuquicamata. The section of the smelter now going into operation, while large, represents only little more than half of the ultimate plant. Equipment for the direct smelting of raw concentrates has been arranged in the conventional manner although needless details have been eliminated wherever possible while mechanical and electrical features not usually found in copper smelters have been incorporated. Access is afforded to all equipment but platforms and walkways have been held to a minimum. The poling and other platforms in the converter aisle, normally subjected to battering by ladles and other heavy equipment in transit, are of concrete construction with steel grid armor embedded in the exposed surfaces. Noticeably absent are the many platforms formerly required for the handling of converter flux since this material is charged to the converters through the side walls of the converter uptake hoods. Clear space with ample headroom is provided under each converter and converter puncher's platform to permit clean-up by small bulldozers. Remote controls have been introduced at many points. Electrical control rooms and control centers have been conveniently located. An electrical tunnel with cross tunnels and escapeways is situated under the entire length of the converter aisle for power feed lines. Skull breaking facilities are in a separate building near the smelter. A silica-slurry building with brick storage area is adjacent to the smelter building so that elevator service is available to both buildings. A smelter office, a change house and lunchroom are provided in convenient locations. Units of the smelter as presently constructed are shown in the plan and table on page 1194. The ultimate smelter will house 7 reverberatory furnaces, 14 waste-heat boilers, 9 Peirce Smith converters, 4 casting furnaces serving 2 casting wheels, and one holding furnace serving a straightline casting machine. Additional crane requirements in the converter aisle will necessitate the installation of special hoisting equipment in space already provided in a raised section of the roof over the casting end of the aisle. Thus a complete crane may be lifted high enough above the crane rails to permit the passing of another crane underneath thereby giving all cranes full use of repair facilities already installed. For the collection of gases, 2 dust chambers, each with separate stacks, will collect converter gases and 2 balloon flues with separate stacks will collect reverberatory furnace gases. Extensions necessary to complete the ultimate plant will be possible with little interruption to normal operations since the future converters and reverberatory furnaces will be added at the east end while additional casting facilities will be added at the west end of the present plant. The future units may be added singly or all at one time depending on requirements.

Jan 1, 1952

By M. R. Goldick

THE Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5 1/2-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mechanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. ORE TREATED Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopyrite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (90 pct minus-200 mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1947

By M. D. Cooper

FOr the purpose of obtaining some first-hand data in regard to the shooting clown of coal in bituminous 'nines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6,020 shots were fired by him during this period. All of the work was clone in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Co. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut.

Jan 1, 1917

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By A. Andreas

New Mexico, after several years as the sixth ranking oil-producing state, was surpassed by Illinois and for 1939 ranks seventh in the United States. Oil production for 1939 was 36,746,840 bbl. Production for 1938 was 35,510,176 bbl., a gain of 0.033 per cent. Production for the year would have been greater had there been a pipe-line outlet for the Vacuum field. The complete shutdown during the latter part of August covering a period of 15 days meant a production loss of over 1,500,000 bbl. of oil. Daily production allowable as set by the Oil Conservation Commission has followed very closely the recommendations of the Bureau of Mines. It has been found that the recommended allowables as quoted by the Bureau of Mines do not always reflect the actual demand, as there is a considerable lag hetween the recommended amounts and the current demands. During the year the various operating companies have done considerable remedial work in setting packers to reduce the gas-oil ratios in the various fields. Six new fields were discovered in New Mexico during 1939; three in Lea County, two in Eddy County and one in Chaves County. In the early part of 1939 a committee composed of the various engineers and geologists recommended subdividing the old Artesia area into various producing pools. This division was accepted, therefore the total number of producing fields in New Mexico is considerably greater than the number of fields in 1938, but does not represent new fields discovered during the year. The southeastern area continues to he the largest producer of oil. During the year 2,716,551 bbl. were produced in Eddy County and 33,690,996 bbl. in Lea County. Total production ill the northwestern part of the state, which includes San ,Juan and McKinley Counties, was 338,293 bbl. At the beginning of the year the daily average nonmarginal well allowable for Lea County was 48 bbl. At the close of the year it was 49 bbl. The daily average production for the year was 97,313 bbl. During the year, 659 wells were drilled in the state, of which 565 were producing oil wells, 15 gas wells, 6 carbon dioxide gas wells and 73 dry holes. Summarized at meeting; manuscript received at the office of the Institute March 18, 1940. * State Geologist, member of New Mexico Oil Conservation Commission, Santa Fe, New Mexico.

Jan 1, 1940

By James Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with excavator mounted upon it, which has reached a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant combining a drag-line excavator on cater-pillar mounting and a gravel-washing plant on a floating barge. The most efficient ones use a bucket of 1 to 2 yd. capacity with boom from 40 to 70 ft. long. The barge varies from 20 by 30 ft. to 36 by 48, and carries the trommel screen, pump, riffle sluices and power engine.

Jan 1, 1936

By Jean Bonnemaison

Societe Miniere & Metallurgique de Penarroya Noyelles-Godault works are located in the northern part of France. The complex includes a lead smelter, a zinc smelter, shops for production of manufactured products and all necessary general services. The zinc smelting complex described in this paper was designed in 1959 to replace an old horizontal retort distillation furnace and was first operated in May 1962. It includes: - a sinter plant producing the zinc sinter for the Imperial Smelting furnace : zinc, lead and bulk zinc-lead concentrates are sintered on a Dwight-Lloyd machine with a working area of 80 sq.m. Cadmium sludges are treated by the wet method in a separate plant for recovery of cadmium. Sulphur dioxide contained in gases goes to a gas washing tower and is subsequently made into sulphuric acid in a plant with a capacity of 550 m.t. per day. - a smelting plant where the process developed by Imperial Smelting Processes Ltd. is applied : the blast furnace which was modified in 1967 has an area of 17.5 sq.m. at the tuyeres level and a section of 24 sq.m. at the top of the shaft. It has a theoretical zinc capacity of 100,000 m.t. per annum. Air blast is heated by means of covers up to the theoretical temperature of 950ºC. Zinc produced is either directly cast into slabs for sale as standard 'good ordinary brand' zinc, or sent to a refining plant where the New Jersey process designed to produce 'special high grade' zinc is in application. Mixes of zinc containing various amounts of lead, cadmium or aluminum are prepared to customer specification in a mixing plant.

Jan 1, 1970

By C. O. Dale, W. J. Rundle

THE upper Mississippi Valley zinc-lead area was the first major lead producing section in the United States. The lead ore, found near the surface in crevices, was relatively pure galena that could be smelted directly into lead, at first in log hearth furnaces and later in more efficient blast type furnaces. French Canadian fur traders encouraged the Indians to mine the lead ore and showed them how to smelt it into lead that had a high value for bullets.1 Nicholas Perrot found lead ore on the Mississippi River bluffs near the junction of Wisconsin and Illinois and in 1690 established a trading post on the Wisconsin side of the river opposite the present site of Dubuque, Iowa.2 Shortly after 1720 discovery of Mine La Mott in Missouri diverted considerable attention from the Upper Mississippi area. Mining continued on a desultory basis with operations concentrated in the Galena, Illinois-Dubuque, area. In 1740 at least 20 miners were at work in the Fever River area around Galena and are reported to have shipped 2500 70-lb pigs of lead to Kaskaskia in 1741.3 Julien Dubuque established a mining and smelting operation in 1790 near the city that bears his name 'and was granted sole right to exploit the mining operations on the lands of the Sauk and the Fox Indians. He is reported to have produced 30,000 70-lb pigs of lead in 1805. Following the death of Dubuque in 1810 the Indians refused to let the white miners enter their lands, and little was done on the Iowa side of the river until the Indians were removed by treaty with the United States government in 1832.4 Early mining was entirely for lead but as the crevices were followed down, increasing percentages of zinc sulphide and zinc carbonate were encountered and at first discarded. Later a market became available for the zinc ores, and hand jigging devices were made to separate the lead," the zinc, and the rock or waste materials. The first record of zinc production from -the area is for 1860. Production of zinc passed that of lead before 1900, reached a peak of 64,000 short tons' in 1917, fell off rapidly and continually to about 2000 short tons in 1938, and since 1940 has ranged from 11,000 to 19,000 short tons. Lead has been of considerably less importance since 1900, and at present only about 10 pct as much lead as zinc is produced. Practically all of the zinc ore has come from orebodies that are rather flat and wide with, considerable length as compared to width. Most of the early lead came from the crevice type deposit, but present production is from the predominately flat zinc orebodies. The Graham-Snyder orebody, scene of Eagle Picher operations, is practically all zinc with little or no lead being recovered. Marcasite, present in varying amounts, makes production of finished concentrates by gravity separation impractical. Satisfactory lead and zinc concentrates have been produced since flotation was introduced in the area in 1927. An acid recovery plant was operated for about 20 years after World War I, but it has been dismantled, and no recovery of the iron sulphides in the ores of the district is being made at the present time. In June 1950 there were three companies operating mines and mills, Tri-State Zinc Co., Calumet & Hecla Consolidated Copper Co., and Eagle Picher Mining and Smelting Co. The Vinegar Hill Zinc Co. had completed a shaft at a new orebody and had started to develop the mine which will supply the Cuba City mill. The Cuba Mining Co. was holding the Andrews Mine inactive. The Dodgeville Mining Co. was not operating but was exploring for additional reserves. Several small mines were selling ore to the Eagle Picher mill. A general area map is given in Fig. 1. The Eagle Picher Mining and Smelting Co. entered the area in 1946 with an active exploration campaign. Leases on a block basis were secured for the area south from the Wisconsin-Illinois line near

Jan 1, 1952

By John W. Roberts

The Federal income tax law permits as a deduction in determining net income "in the case of mines,... a reasonable allowance for depletion and for depreciation of improvements, according to the peculiar conditions in each case, based upon cost, including cost of development not otherwise deducted: Provided, that in the case of such properties acquired prior to Mar. 1, 1913, the fair market value of the property (or the taxpayer's interest therein) on that date shall be taken in lieu of cost up to that date." The law provides for a reasonable allowance but the regulations provide for a definite method of computation that possesses more the virtue of simplicity than that of reasonableness. Article 210 of Regulations 45 reads: "When the cost or value as of Mar. 1, 1913, or within 30 days after the date of discovery of the property shall have been determined, and the number of mineral units in the property as of the date of acquisition or valuation shall have been estimated, the division of the former amount by the latter figure will give the unit value for purposes of depletion, and the depletion allowance for the taxable year may be computed by multiplying such unit value by the number of units of mineral extracted during the year." This is simple, but is it reasonable? The intent of the law is clearly that the cost of the ore in the ground shall be considered as part of the cost of the same ore when removed and sold. The regulations fail to carry out that intent, because of the unwarranted assumption that all the ore in the mine cost the same amount per ton. This is what gives the Treasury Department's method its simplicity, but at the same time robs it of its reasonableness because the assumption is contrary to fact. It is self-evident that a ton of ore near the surface or exposed by present workings is worth much more than a ton buried so far down in the earth that it cannot be removed for many years. If no improvements in mining methods were expected, the value of deeply buried ore would be further reduced by the greater expense that would be required to

Jan 1, 1922

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By J. M. Pilcher

The application of oil to coal for-the reduction of dust has greatly increased the consumers' satisfaction with solid fuels, especially those for domestic use. The combination of oil-treated coal and automatic firing by a small stoker has made possible clean, automatic heating with bituminous coal. This, with the added pressure of competition by other fuels, has caused a rapid development of oil treating practice. A variety of materials derived" from petroleum oils is available from which one may choose for treating a par-ticular coal. Until recently, however, little information had been published to guide the choice. It is most im-portant that the proper type and amount of oil be used in order that all coals marketed as "dustless" will be reason-ably dustless, and thereby maintain a good reputation for oil-treatment. During the past two and one-half years, an investigation of a number of the problems related to the treatment of coal with oil has been conducted at Battelle Memorial Institute. This project was jointly sponsored by Bituminous Coal Research. Inc., Standard Oil Company of New Jersey, Sun Oil Company, and Viking Manufacturing Company. A progress report giving the principal results of the work of the first year was presented before the American Society of Mechanical Engineers in December 1937.1 The present paper is a summary of the entire inves-tigation.

Jan 1, 1939

By Leon Y. Sadler

Three new transfer functions relating the time response of the amount of floatable mineral in the under flow to time-dependent changes in the amount of floatable mineral in the feed to the cell are presented. Using experimental stimulus-response data obtained from the flotation of -200+325-mesh glass spheres in a rotor-stator-type cell, the new transfer functions are compared to the only transfer function to be presently found in the literature by nonlinear least-squares fitting in the frequency domain. The new mathematical model based on the amount of available bubble surface area and its rate of introduction is quite promising. The transfer function which allows for a distributed first-order flotation rate constant also gives good results. Simultaneous sodium chloride tracer and glass bead stimulus-response tests show that the mixing conditions in the cell were nearly ideal. It is felt that the new transfer functions presented offer excellent alternatives for use in the design of automatic process control equipment for the continuous mechanical froth flotation cell.

Jan 1, 1974

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.' It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

By R. Littlewood

The concepts of "redox potential" and "oxide-ion activity" are suggested as measures of the fundamental slag properties of interest to the extraction metallurgist. Thermodynamic data for single oxides are presented graphically in these terms and a method of expressing desulfurization of steel in electrochemical terms is indicated. The application of the theovy to mixtures of oxides (slags) is discussed and the redox potential is shown to provide a link between all the redox equilibria in a slag-metal system. In particular, the redox potential of the slag, its basicity, and the oxygen partial It is now generally recognized that slags are mixtures of polymeric anions of silicates, aluminates, phosphates, and so forth, neutralized by cations. However, conventional thermodynamic treatments of slags have almost always been in terms of activities of the pure component oxides (e.g., SiO,, CaO, A1203, and so forth), which are known not to exist as such in slags. While this type of empirical treatment is perfectly acceptable and provides a rigorous and self-consistent way of considering thermodynamic properties, it can give little guide to the structure of slags, since its very nature ig- pressure are closely connected. Direct deternzination of these by electrode-potential measurements is possible. Literature calculations of ion activities in the system Ca0 -Fe0-SiO,/molten iron are used to evaluate redox potentials, which are shown to correlate with data on sulfur partition in the system. In addition to its application to equilibrium conditions, an electrochenzical approach to slag-metal reactions might provide a basis for new methods of studying the kinetics of these reactions and for plant-control instruments in the pyrometallurgical industries. nores such complications. Recently, the thermodynamic properties of some slags have been successfully interpreted in terms of activities of anions of varying degrees of complexity. (While these have been successful curve-fitting exercises, there is no direct implication that the anions used in the models are necessarily the ones which actually exist in slags.) The success of these ionic thermodynamic treatments is encouraging but a complete picture of slag structure is still a long way off. What is needed is a complete knowledge of the values of stability constants for all reactions in slags of the type:

Jan 1, 1965