Search Documents

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing metamorphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the granodiorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore- forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation.

Jan 1, 1939

It is interesting to note that during the period that has elapsed since the Institute's formation, wood charcoal, anthracite and bituminous coal, as well as beehive and by-product coke, have been used as blast-furnace fuels, that the reign of supremacy of each fuel was associated with specific periods, and that each successive era was marked by a production of pig iron greater in quantity than the one it followed (Fig 1). The transition of the manufacture of blast-furnace iron from charcoal to anthracite and then to beehive coke, and ultimately to by-product coke, is a reflection of the economic limitations of each fuel coupled with availability sufficient to meet the increased demands of each succeeding decade. It is a pattern that has been followed almost without exception in the history of pig iron in every country. CHARCOAL Colonial production of iron relied exclusively on wood char- coal as a fuel, and the iron industry of this count recognizes the important role played by this fuel. Charcoal iron has been available to consumers since the beginning of the organized iron industry in America in 1645, by John Winthrop at Saugus, Mass.,1 and although its greatest use antedates the formation of the Institute, it is still used to some extent. Until about 1840 nearly all of the pig iron manufactured in the United States was made with charcoal, and it continued as a principal smelting fuel until 1855.2 After that time, more pig iron was produced with other fuels, despite the fact that

Jan 1, 1948

By R. D. MacDonald, John Dasher, A. M. Gaudin

ION exchange is a widely used unit operation in water treatment and elsewhere in chemical industries. It has occasionally been used in hydro-metallurgy for treating plating, pickling, and rayon wastes Concerning ion exchange in extractive hydrometallurgy—for treating ore leach solutions— the literature prior to the Geneva Conference has given only hints."-" Yet most of the ore leach plants now being built or completed in the last three years use ion exchange for this purpose. Most of these plants are used for extracting uranium. The overall process for leaching low grade uranium ores and the history of its development have been given in the authors' previous papers.',' The object of this paper is to discuss certain engineering aspects of the new application of ion exchange to recover dissolved values from ore leach solutions. Necessarily the illustrations will be taken from the first application—to uranium metallurgy. Although ion exchange processes have been devised in which separation of spent residue from pregnant liquor is not required, as in the RIP process,"-'I only ion exchange operation, in which the resin is contacted with a clear solution, will be discussed in this paper. Uranium exists in acid leach liquors mainly as the cation UO," and can be adsorbed completely by cation exchange resins, but the adsorption is not selective as other cations such as Fe++, Fe+++, Al+++, Mg++, Mn", and Ca++ are also adsorbed. Uranium, however, forms complex anions with sulfate, phosphate," Carbonate"~"~ and even with chloride if the solution is strong enough.15 These anions can be adsorbed by anion exchange resins. The strong base anion exchangers have a very strong preference for these complexes and hence this adsorption is very selective. In this paper, the examples concern acid sulfate leach liquors from which uranium is adsorbed as UO,(SO,),-% and UO,(SO,),". Materials and Equipment Ion Exchange Material—Ion exchange materials include natural and synthetic; organic and inorganic; cationic and anionic; and weak, intermediate, and strong varieties. They consist of fragments or beads normally in the size range —16 to $50 mesh. The newer varieties have been developed to have greater stability, chemical strength, and/or capacity than earlier varieties. The resin used for uranium recovery is a strong base anion exchanger.* To make * Such as Rohm and Haas Amberlite IRA-400 series, British Permutit DeAcidite FF. Permutit lonac SE. and Dow Nalcite SAR. this resin, styrene plus a few percent divinyl benzene are polymerized into long chains with occasional cross links. This resin in bead form is then reacted to introduce quaternary amine groups onto most of the aromatic rings.' These resins are water-avid gels of specific gravity of about 1.1, which shrink and swell by osmosis when the ionic content of the surrounding solution is changed. The beads which are shown in Fig. 1 can be broken like an onion by rapidly replacing 15 pct H,SO, with water. This organic gel can also be broken by mechanical handling as by a centrifugal pump. Otherwise it is remarkably stable. It is unharmed by fairly strong acid or alkali, oxidizing or reducing agents, and heat up to 70°C. The strong base resin when completely in the chloride form (with a chloride anion on each quaternary amine group) holds over 107 g of C1- per dry kg. As all these chloride ions can be displaced by other anions, the resin has an exchange capacity of over 3 g equivalents per dry kg. However, the resin is sold and used by moist volume. The moist resin contains about 50 pct water, weighs about 43 lb per cu ft, has 40 pct voids, and an exchange capacity of over 1 g equivalent per liter of bed volume. Ion Exchange Equipment—Ion exchange equipment used for recovery of uranium from leach solutions is substantially identical to that developed for water treatment and other applications.'" The resin beds are held in closed tanks or columns which, in the uranium plants, have been standardized at 7 ft diam and 12 ft high. The resin bed

Jan 1, 1958

A. 0. ASHMAN, Palmerton, Pa. (written discussion *.).-Mr. Newcomb's paper has interested me greatly, as I have had numerous experiences along this line. I do not think enough emphasis can be put on his warn-ing to keep platinum couples free from contact with quartz tubes, as silica shows a tendency to alloy with platinum to a surprising degree even at low temperatures. I have frequently had evidence of silica contamination in a perfectly good tube, in which there was seemingly no possibility of a reducing atmosphere. This is rather important as it seems to be common practice to insulate, as well as protect, the wires by means of- capillary silica tubing, thus allowing the entire wire to be in contact with the silica. The best way to mount a couple in a silica protecting tube is by means of double-bore porcelain insulating tubes, the protecting tube being slightly longer than the couple so as to leave a space between the couple and the end of the tube. In this way there is no possibility of contamination from silica. In no case should silica capillary tubes be used to insulate platinum wires. Mr. Newcomb states that there is still much to be desired in pyro-meter protecting tubes; this is in keeping with my experience. From a practical standpoint there is not a satisfactory pyrometer tube on the market for high temperatures; with all clue respect to the many improve-ments and good work recently done in this line. I believe that the whole future development of pyrometry is dependent on the development of suitable refractories. With suitable refractories, for example, Darling's1 work with liquid couples could be developed to a practical basis, making possible the use of base-metal couples to replace platinum.

Jan 12, 1919

By J. S. Bowles

DISCUSSION, M. Cohen presiding J. W. Christian (The Inorganic Chemistry Laboratory, oxford, Englandl)—I was very interested in Dr. Bowles' results on the suppression of the transformation by solid films of alcohol or propane. The transformation in cobalt, which is also martensitic, can be explained by a mechanism involving the reflection of "half dislocations" down a series of atomic planes.* This reflection process is similar to that considered by Frank13 for plastic deformation on a single slip plane and, as he pointed out, reflection would be impossible if the metal were immersed in a liquid of higher density. It seems possible that solid films of alcohol have a similar effect on the lithium transformation. Reflection should also be possible at a grain boundary, though a higher kinetic energy of the dislocation, and hence a lower temperature would be required. As Dr. Bowles used coarse grained polycrystalline speci- mens, transformation on cooling should still have occurred in grains which did not form part of the outside (free surface) of the metal. This may account for the X-ray lines of the low temperature phase which were found. There is thus the interesting possibility that in a polycrystalline specimen a liquid, or in some cases a solid, film of material of or or higher density will lower M,, while in a single crystal it should suppress the transformation completely. In the case of cobalt it is necessary to find a dense liquid which will not react with the metal at the transformation temperature. The most promising liquid appears to be pure lead, but it is very difficult to devise a method of investigating whether or not this does suppress the transformation.

Jan 1, 1952

W. A. SCHLESINGER,* Denver, Colo.-Two problems are of great interest to the radium manufacturer at the present tine: The first is to perfect a process, more efficient and more economical, which is capable of treating a greater variety of ores. . Practically all the radium now manufactured in the United States is extracted from carnotite ores and these vary a great deal according to their location. The amount of sulfates contained in the ore is of particular importance, and any straight acid-leaching method, such as developed by the Bureau of Mines, becomes prohibitive when the ore contains more than 0.5 per cent. of sulfates, as the sulfates go into solution and naturally precipitate the radium as insoluble radium sulfate. Since the amount of ore obtained from any one claim is usually comparatively small, it is necessary to work a number of claims in different localities, and a process, in order to be commercially satisfactory, should handle all of these ores. In other words, it would be entirely unprofitable for radium manufacturers to employ any process which cannot treat any but sulfate-free ores. He must deal with carnotite containing appreciable amounts of sulfates, and must be able to work this in with the other ores. Carbonaceous ores from certain sections in Utah; which are known to contain as pinch as 1.0 per cent. and more of volatile matters, are prone to a, nitric acid-leaching process. The second problem relates to the treatment of concentrates. There is no doubt that a very large amount of low-grade ore, containing less than 0.75 per cent. uranium oxide, is available. It has been demonstrated that these ores can be concentrated, but there is still room for research

Jan 11, 1918

By Niels Hansen

Dispersion-strengthened aluminum products consist of an aluminum matrix containing finely distributed ceramic or intermetallic particles. Examples of the two types of product are SAP, in which the dispersed phase is aluminum oxide, and materials made from atomized aluminum alloy powder, in which the dispersed phase can be FeA1, particles.' A fundamental difference between the two types of product is that the elongation of aluminum/aluminum oxide products decreases with increasing temperature, whereas the elongation of aluminum- FeA13 products, like that of aluminum alloys, increases with increasing temperature. As regards the structural stability, aluminum/aluminum oxide products are stable to temperatures above 600° C as aluminum oxide does not react with aluminum, whereas prolonged heating at above 400°C of aluminum-FeA1, products leads to coarsening of the intermetallic phase and loss of strength.' On the basis of these results it is supposed that a dispersion-strengthened product combining strength, ductility, and stability at elevated temperatures may be obtained if the dispersed phase reacts with the matrix in such a way that the reaction does not proceed at any significant rate at the application temperature. Different ceramic or intermetallic compounds may be selected as the dispersed phase, and, as alloying of the matrix phase may also influence the reaction, many possibilities exist for each metal. In the present study, aluminum products containing different oxides have been examined. For a reaction to take place between the dispersed oxide and the aluminum the free energy of formation of the oxide (MeO) must be greater than that of aluminum oxide; the difference should, however, not be too great in order to limit the reaction rate. Furthermore the aluminum alloy formed when aluminum reacts with the dispersed oxide should have a melting point near

Jan 1, 1969

By T. S. Lundy, C. J. McHargue

HE diffusion rate of v48 in single crystals of bee vanadium has been determined at temperatures from 1002° to 1888°C. Standard techniques of lathe sectioning were used for specimens annealed above 1500°C while sectioning by grinding was used for specimens annealed at lower temperatures. As will be seen, the lower-temperature data is enhanced on an Arrhenius-type plot relative to values expected by extrapolation of the high-temperature data. Single crystals were obtained from Linde Co. In Table I the analysis supplied by the vendor is compared with an analysis at Oak Ridge National Laboratory of a sample after a diffusion anneal. The isotope v4' was prepared by the Isotopes Division of Oak Ridge National Laboratory. Proton bombardment of a titanium target in the 86-Inch ORNL Cyclotron was followed by a carrier-free chemical separation. Nineteen specimens, 1/2 in. diam and 3/8 in. long, were cut from the as-received vanadium single crystals. Each specimen was machined with the flat face perpendicular to the longitudinal axis. Specimens were polished through 1/0 emery paper and were etched with 25 pct HF-10 pct H2SO4-10 pct HNO3-55 pct H2O. The polishing and etching steps were repeated until a satisfactory surface finish was achieved. The isotope was electroplated onto the specimens from a neutral solution. Counting rates of the deposited layers were approximately 100 counts per sec. At temperatures above 1200°C specimens were annealed in a tantalum resistance furnace under an argon atmosphere. Temperatures were measured with a Pyro micro-optical pyrometer and a Pt-Pt 10 pct Rh thermocouple. At lower temperatures the specimens were sealed in evacuated quartz ampoules and annealed in Kanthal wire-wound horizontal tube furnaces. A severe reaction occurred at 1200°C between the quartz and the vanadium. This

Jan 1, 1965

By S. Ramachandran, R. A. Walsh

Many investigations have shown that the manganese enhances the deoxidation power of silicon. Here it is suggested that this phenomenon could be explained in terms of the formation of impure silica. Data of Hilty and Crafts on the Fe-Mn-Si-O System has been evaluated on the basis of the reaction S_i + 20 = (SiO2) where (SiO2) denotes silica of variable activity. The activity of silica in this system is a function of aMn/aSi and the temperature, and can be described by the equation 12700 l°gaSiOz = -6.85+ - - 0.5 log aMn /asi PRACTICAL melting experience has shown that it is helpful to maintain a certain range of Mn/Si ratio in deoxidizing quality alloy steels. Herty,1 as early as 1932, reported a strong association between manganese and silicon as did schenck2 and Korber and Oelsen3 in later work. More recently, Hilty and crafts4 have studied the solubility of oxygen in the Fe-Si-O system, both with and without manganese. Their study confirmed the marked ability of manganese to increase the deoxidizing power of silicon. This phenomenon has remained unexplained in the liter,ature5 since it has been shown that manganese has virtually no influence on the activity coefficients of silicon or oxygen.= In this paper, an explanation for the role of manganese is suggested and equations are devised for quantitatively describing this influence. DISCUSSION Hilty and crafts4 equilibrated their melts under an argon atmosphere and the system established equilibrium with a self-generated slag which was not always the oxide of lowest free energy. Drawing on the early work of Korber and Oelsen,3 it was reasoned that the formation of complex Fe-Mn-silicates

Jan 1, 1963

By R. Schuhmann, J. Th. Overbeek, P. L. De Bruyn

W. E. Ewers (Commonwealth Scientific and Industrial Research organization, Melbourne, Australia)— Any attempt to elucidate further the meaning of the contact angle, particularly if it deals with the magnitudes of those mysterious quantities rsa and YRL, is certain to receive attention from those interested in the fundamentals of flotation. It is imperative, therefore, that attention should be drawn to a serious defect in the treatment by de Bruyn, Overbeek, and Schuhmann. Their Eq. 5 dy = — ld/u — Th2odiH2n states correctly the relationship between the change in surface free energy dy, the surface excesses Tx and Th2o of the components x and H2O and the changes du, and dph2o in the chemical potentials of these components. This equation applies for constant pressure and con- stant temperature and for the interface of the solid in contact with the solution of X. The relation remains valid when 1.1 is defined so that TH2O becomes zero and the equation becomes dr = — r:dur [17] From this equation de Bruyn et al. correctly concluded that increased adsorption of the collector at the liquid solid interface would reduce the interfacial energy ysl. Their second conclusion, however, that an increase in the contact angle, corresponding to a greater decrease in rsa than in rsL can be attributed to greater adsorption of X at the solid-air interface than at the solid-liquid interface is quite unjustified. The portion of the solid surface from which the collector solution has been displaced by air must be considered in terms of the equilibria between the gaseous phase and the surface. If the pressure and temperature

Jan 1, 1955

By Walter Snelling

IN the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I 'experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment.

Jan 4, 1915

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927

By Charles Mabery

So FAR as the elementary composition of petroleum is -known, it may be briefly stated. Petroleum consists principally of a few series of hydrocarbons, with admixtures of sulfur, nitrogen, and oxygen derivatives in comparatively minute proportions, which may be regarded as impurities to be removed in the preparation Of commercial products. But as each series is represented by many homologs, in the aggregate, crude petroleum is an extremely complex mixture of hydrocarbons and their derivatives. In part, these hydrocarbons individually conform in structure to the system of synthetic hydrocarbons whose structure is well defined and -represented by the typical series CnH2n+2, CnH2n, the series CnH2n-2, CnH2n-4, the members of which have not been sufficiently studied to establish their structure, and the series CnH2n-6 composed of the aromatic group, benzene and its homologs. Hydrocarbons of greater density contained in the portions of petroleum that cannot be distilled without decomposition doubtless have less hydrogen than is represented by these formulas. Since to every hydrocarbon there is a definite temperature, even in vacuum, at which its constituent carbon and hydrogen atoms fall apart, and since for the heavier bodies this temperature is not much above 360° C. in vacuum, it is evident that some other method than distillation must be devised for their separation if anything further is to be learned concerning their individual constitution. CLASSIFICATION OF PETROLEUMS There is such a wide variation in the composition of petroleum from different fields, it would seem possible to make a classification on this basis were it not that no single variety is entirely free from hydrocarbons contained in others. Such a classification has been suggested of the exceptionally pure Pennsylvania petroleum, the sulfur oil from Trenton

Jan 2, 1920

By Hans M. Ewoldsen

The generation and evaluation of solutions to body force problems is of extreme interest to the geotechnical profession, as all natural stress states must necessarily include some contribution from the weight of the material. In this chapter the elastic solution for the stress field around a circular, horizontal tunnel at an arbitrary depth beneath the surface of a half-space is reexamined. The influences of body force, initial stress, and free surface proximity are examined and related to in-situ cases. The solution as presented deals only with an isotropically elastic medium; this medium is further considered only in a half-space configuration. It is readily apparent that these restrictions impose severe limitations if analogies are attempted with in-situ cases where geologic discontinuities, inhomogeneities, and irregular boundaries exist. The question might be raised as to the propriety of geotechnically oriented researchers even considering such idealized conditions. There is, however, much to be gained from study of such solutions. The lack of geologic discontinuities and inhomogeneities allows the investigator to separate and leisurely examine such parameters as are included in the solution, without worry of interrelationships of a host of other parameters. Further, elastic solutions have had extensive usage prior to the development of such techniques as the finite-element solution. It is interesting to compare body force solutions with the external field solutions which in the past have been used for design purposes. Finally, the exact solution may be used to verify the accuracy of the finite-element type of solution. The mathematical solution on which this chapter is based was originally developed by R. D. Mindlin.l Because of the complexity and length of the solution, no attempt was made to determine the resultant stress fields until the advent of the present-day high-speed digital computer. How-

Jan 1, 1972

By Gilbert Doan

AN extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, spon-sored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to

Jan 1, 1936

Optimism over the continued growth of coal ex- ports received a significant shot in the arm September 18 at Norfolk, Va., when huge, new ship coal-loading facilities of the Norfolk & Western Railway were formally dedicated before a large audience of American and foreign dignitaries. Guest of Honor at the occasion was Christian A. Herter, Special Representative for Trade Negotiations, who, in a speech, stated, "The prospects for the expansion of our coal exports are excellent. The competitive pricing and high quality of our coals, whether for the production of coke for steel mills or for the generation of electric power, have won the respect of consumers everywhere in the world. Last year, the United States coal industry exported over 40 million net tons. . . . There are excellent reasons to believe that by 1970 we shall be exporting at double this rate."

Jan 10, 1963

By C. R. St. John, R. W. Lindsay, Charles R. Austin

MANY of the factors influencing the creep behavior of ferrous alloys have been investigated and reported upon in the literature, including such variables as grain size, steelmaking practice, nature and stability of the microstructure, and the effect of alloying elements in steels. However, with respect to the latter, the microstructures involved are usually heterogeneous and as a result the effect of the addition is related to its effects on the various phases present in the microstructure. In the instances where this structure consists of ferrite and carbide, the behavior of the alloy addition will be related to its action in strengthening ferrite and in opposing temperature softening of ferrite as well as coalescence of carbide. The present paper is the third in a series comprising a comprehensive review of investigations on the properties of iron binary alloys. 1.2 Its purpose is to describe the results of isolating one microstructural phase, namely ferrite, and studying its creep characteristics in both the unalloyed and alloyed conditions. This should aid in establishing to a large degree the importance of ferrite in the creep behavior of steels consisting of the previously mentioned ferrite-carbide aggregate. REVIEW OF PREVIOUS WORK In view of the fact that the present investigation deals only with the effects of silicon, manganese, chromium, molybdenum, nickel, and cobalt, and to a certain extent with the effects of carbon, the review of previous literature will be confined to these elements. Practically no references were encountered dealing with the influence of these elements on the creep characteristics of the isolated phase. However, various contributions have dealt with the creep behavior of low-carbon steels alloyed with the elements under consideration. A particularly concise review in this respect is given by Bullens (Battelle)3 and much of this material has been drawn upon. The definite improvement in creep resistance and high-temperature strength conferred by molybdenum is well known. Published suggestions by the A.S.M.E.4 permit of an increase of some 2000 to 5000 lb. per sq. in. in permissible design loads over a temperature range from 650° to 1000°F. as a consequence of additions of 0.40 to o.60 per cent of this element in carbon steels of the order of o.25 to o.35 per cent carbon content. Babcock and Wilcox Tube Co.5 has published data showing the pronounced increase in stress necessary to cause one per cent creep per 10,000 hr. when additions of 0.5 or 1 per cent molybdenum are made to a plain carbon steel. These data apply to temperatures over a range from 800° to 1000°F.

Jan 1, 1945