Search Documents

By A. Coskun, J. F. Elliott

The activity of aluminum in liquid Al-Fe alloys .has been measured by an improved version of the transportation method in which the metallic vapor has been collected by its solution in a metallic condenser. The results can be represented by the equation: log yAl = -3.0(1 - xAl2) (0.6 < XAl < 1.0) This equation applies at 1315°C. MORRIS and zellarsl adapted the transportation method for measuring the vapor pressure of a com- ponent of an alloy at high temperature. We have modified their technique further2 for use with metals that are strong oxide formers. In the present case the method has been applied to the Al- Fe system to obtain the activity of aluminum in the liquid region at 1315°C. Dried ultrahigh-purity hydrogen (Matheson) is the carrier gas. The operations, Fig. 1, of deoxidizing the gas, equilibrating the gas with the sample at 1315";, and then collecting the aluminum vapor are all accomplished within a single, continuous alumina tube to avoid contamination of the system by leaks. De-oxidation to a very low level of PO2 (<10-25 atm) is Obtained by passing the hydrogen through a tightly packed bed of aluminum powder. The temperature of this bed increases to approximately 550°C in the direction of the gas flow. The boat containing three pellets of the alloy is supported on the end of a

Jan 1, 1969

By D. F. Coolbaugh

Successful mine exploration requires sound planning and modern exploration techniques, but it also requires perseverance and the right timing. The La Caridad mineral area has been known for over 70 years, but as with many mines, it was not "discovered" until viewed under new economic conditions and exploration philosophies. Present exploration of the La Caridad area began in 1964 and was carried out under a joint Mexican Government-United Nations Project. Detailed exploration was begun by Asarco Mexicana S.A. in late 1968. The geology of the La Caridad deposits conforms, generally, to the "porphyry copper" deposits of Arizona. However, breccias and pegmatites play a very important part in the emplacement of mineralization.

Jan 1, 1972

By George E. Beavers

It is well to understand at once that converter gas is always mixed with copper blast-furnace gas at Copperhill before entering the Glover tower, and, at times, roaster gas is also added along with the converter and blast-furnace gas. Fig. 1 is introduced to show the variations in the sulfur dioxide content of the gas and the ability of the acid-plant operator to control the variations, resulting in a very even grade at the Gay-Lussac tower entrance. The sulfur dioxide content of the gas entering the Gay-Lussac tower must be low and regular to assure low niter consumption. The blast-furnace gas alone is rather uniform as regards sulfur dioxide content and the variations, as shown in Fig. 1, are chiefly caused by converter changes—out for charging, slag pouring, copper pouring, and, of course, the "finish." The combined gas during the converter finish is, at times, almost free of oxygen and the sulfur dioxide content reaches 13.0 per cent. At such times air is added at the Glover tower.

Jan 1, 1934

By R. M. Treco

The effect of small additions of oxygen on the hardness, density, and lattice parameters of high purity zirconium has been investigated. Precision parameter values and density of oxygen-free zirconium are given as: a,, - 3.2258 kX units, C = 5.1373 kX units, O23 = 6.507 g per cc. THE effect of oxygen on the hexagonal-phase lattice constants of pure zirconium is of interest for several reasons. The extensive hardening effect of oxygen noted by previous investigators&apos; must be due in part to the lattice distortion accompanying its introduction and possibly to the preferred position of the oxygen atoms. De Boer and Fast&apos; have shown that oxygen is taken into solid solution in large amounts, appearing to occupy an interstitial position. These authors also found that expansion of the lattice was not uniform since the a axis attained a constant value after the addition of 10 atomic pct while the c axis continued to expand. It was thought in the present work that this expansion of the zirconium lattice with increasing amounts of oxygen

Jan 1, 1954

By Keith Leonard Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 [ ] Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300" C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200°, C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By George H. Jones

NO STRANGER phenomenon exists in the American mining industry today than the so-called bootleg anthracite industry in Pennsylvania which now produces probably close to 15 per cent of the total hard coal out- put of the State. Instead of being what - was first thought to be a temporary condition, countenanced because of the desperate condition of some of the miners at the depth of the depression. it is thriving now as never before. Re- ports of it have penetrated all over the world, as exemplified by inquiries concerning it in Durban, South Africa mentioned by John C. Cosgrove in his article in the July MINING AND META LURGY.

Jan 1, 1939

By E. R. Smith

ANALYSIS of the requirements for gun perforation equipment suitable for penetrating casing and cement showed that these points would be involved: (1) Powder charges electrically detonated under high fluid lieads and at remote distances. (2) Selective firing of sliots in sequence. (3) Sufficient velocity for the bullet to penetrate at least two strings of seamless casing and all cement beyond the strings. (4) Heat-treatment of steels to withstand great pressures and penetration. (5) Esclusiorl of fluid under extremely high hydrostatic pressure. (6) Stranded steel wire line acting as weight - suspending and current - carrying medium. (7) Firing controls operated above the surface. (8) Determining gun depth and suspended weight by means of the wire line. (9) Portability for field use.

Jan 1, 1936

Thus far virtually the sole theme of the conservationist has been the preservation of natural resources. Little thought has been devoted to the conservation of America&apos;s most significant asset-her people. True, considerable effort has been devoted to conserving man&apos;s physical strength by the invention and application of labor-saving machinery. Notable progress has been made also in the conservation of man&apos;s health through important discoveries in medicine. However, little if any positive success has been achieved in the conservation of the most valuable attributes of man-intellect, skills, manpower. Human resources are interrelated and interdependent. There is no monopoly on knowledge or skills&apos; or human energy. No one must sell them short. All the knowledge and all the skills and all the energy possessed by all men are required to render all the services needed by all men. One of the major sources of wasted manpower is found in the nation&apos;s schools, with an educational system based on the outmoded theory of uniform education for all. Actually, if democracy means free initiative for the individual, and unlimited progress at the maximum rate of speed of which the individual is capable, then our public schools are not democratic in-

Jan 1, 1950

By J. Th. G. Overbeek, R. Schumann, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.1-3 Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles.

Jan 5, 1954

By Cadwallader Evans

THE American Institute of Mining Engineers was organized in the anthracite region of Pennsylvania by men who were primarily interested in anthracite. Its first meeting, at Wilkes-Barre, Pa., in the Northern Anthracite field, on May 16, 1871, resulted from a call sent out by three outstanding men of the anthracite .industry: Eckley B. Coxe, R. P. Rothwell, and Martin Coryell. The best known of these was Eckley B. Coxe, who was the manager of large hold¬ings operated by him and his family,. and who is remembered as the inventor of a special grate for burning very fine anthracite, known as the Coxe traveling grate, which is still very widely used. R. P. Rothwell was a well-known consulting engineer of the region, as was Martin Coryell, who was associated with another well-known anthracite family, the Pardees. There is no record of the discussions that resulted in this initial meeting, but it is safe to assume that the formation of the Institute was largely influenced, through appreciation by the founders, of the necessity for a free exchange of information covering the whole of the mining industry. One of the rules adopted at the first meeting was:

Jan 1, 1947

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By Fred Bond

WHEN some materials are ground dry in a ball mill, a stage of comminution is reached at which the finely divided particles begin to adhere to the balls and to the mill lining. As grinding progresses, a coating accumulates upon the grinding media, which tends to cushion the impacts and thus retard reduction of the material, and finally becomes so thick that all grinding ceases. At this stage, the characteristic noise produced by the grinding media dur-ing normal mill operation changes to a dull, muffled sound. In most instances, the formation of the coating marks the practical limit of size reduction. Industrial requirements for fine grinding frequently meet with this obstacle, and the tendency in many com-mercial operations to grind materials to a higher degree of fineness than formerly makes the solution of this problem an im-portant one. The phenomenon is of far greater importance, therefore, than the limited amount of research and technical discussion devoted to it implies. In order to learn more about the coating of different materials when ground dry to a high degree of fineness, certain labora-tory tests were made from which it was found that different materials form coat-ings at widely different size distributions. It is probable that most materials will coat if they are ground fine enough; the exceptions have inherent lubricating qual-ities, like coal and graphite.

Jan 1, 1940

By Franklin Allison

THE influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such a remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of, properties that are obtained from steel is due, largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allotropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1800° F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident.

Jan 3, 1927

By D. A. Koss, R. O. Gordon

Changes in the ultrasonic attenuation in steel specimens have been observed during tensile tests. Samples of AISI 1020, 1045, and 1095 steel quenched and tempered to a spheroidized condition have been used. Both attenuation and microstrain measurements fail to reveal preyield dislocation motion in the as-tempered specimens. Upon reapplication of the load to samples in the strain-aged condition there is a large preyield attenuation increase but no observable micvostrain up to 90 pct of the flow stress. These and other observed changes can be related to changes in the free disloca-tion density and the average dislocation segment length. The results show that the increase inflow stress in the strain-aged condition is caused by increased fric-tional stresses rather than by dislocation pinning. Strain aging is found to proceed through three distinct stages. The second of these follows the t2,3 law and is characterized by an activation energy of 20 kcal per mole. RECENT years have seen substantial progress in the understanding of the sharp yield-point phenomenon in metals; the influence of solute atom pinning of dislocations, of dislocation multiplication, and of the stress dependence of dislocation velocity on the stress-strain curve has been investigated. Evaluation of the relative importance of these factors in the various metals and alloys is not complete, however, because observation of the stress-strain curve alone is not sufficient to determine the yield mechanism. In the experimental study of the sharp yield point it would be desirable to be able to directly observe the dislocations in a bulk specimen. Ideally, the observations should be made during deformation because of the rapidity of recovery processes in lightly strained metals. While direct observation of dislocations under these conditions is not possible, certain physical properties sensitive to the dislocation structure can be observed while a test specimen is undergoing deformation. Of these properties, one of the most useful is the ultrasonic attenuation. The total observed attenuation, a, is due to a number of causes: acoustic diffraction, scattering by inhomogeneities in the structure, heat flow, magnetostriction, and dislocation damping. Satisfactory measurements of the absolute a are difficult to make because all of these factors cannot be evaluated in any given specimen, but changes in a due to changes in the dislocation contribution alone can be reliably observed by appropriate technique. Because dislocation damping is sensitive to small concentrations of long, free dislocation segments, observation of acoustic attenuation due to dislocations is particularly useful in the study of the early stages of plastic deformation. In the experiments to be described, acoustic-attenuation measurements have been made on steel samples as these were pulled through their yield in tension. While many details of dislocation-damping phenomena in the bee metals remain obscure, the main characteristics of this type of internal friction are established. At low strain amplitudes and at frequencies well below that of dislocation resonance (the conditions of these experiments) the dislocation contribution to a is given by1 where A is the density of freely oscillating dislocation segments, L is the average segment length, B is the damping constant for a moving dislocation, w is the frequency, O is an orientation factor, C is the dislocation line tension, and t is a numerical factor relating average segment length to the distribution of lengths. Because of its fourth-power dependence on L, a is highly sensitive to changes in dislocation free segment length such as might arise from unpinning, recovery, jog formation, or dislocation intersection. The above equation is not valid near the resonant frequency of dislocations, but the segment length in steel is believed to be much too short to cause over-damped resonance near 10 Mc; this will be discussed later. In the present experiments plastic-strain measurements with a sensitivity of 2 x 10-5 were also made during the early stages of loading in order to detect preyield strain. The general plan of the experiments is to observe

Jan 1, 1967

By John G. Hall

The pumping operations at the Chief mine have been unique in the respect that for many years the entire flow of water into the mine has been disposed of by pumping into natural underground " caverns" or "sinks." Volumes up to 4000 gpm have been pumped into these caverns with no apparent tendency for the caverns to fill with water, and it has never been proven that any of the water returns to the mine workings. Major pumping operations have been carried on during two periods, the first from 1918 to 1927, and the second from 1942 to the present time.

Jan 1, 1949

By James Aston

A proper consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. Manufacture of Wrought Iron The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man&apos;s needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today&apos;s scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort&apos;s invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By E. M. Chance

HERBERT M. WILSON, Pittsburgh, Pa. (written discussion).-Permit me to endorse the author&apos;s conclusions and their form of presentation as ,being, in my judgment, the last word &apos;on the subject of lights for the illumination of coal mines. I also feel that the open-flame oil lamp has outlived its usefulness, and that it should go, in the interests not only of safety but of efficiency. Where an open-flame lamp can be used with safety in non-gaseous mines, the acetylene light adds materially to efficiency by its better illumination, and to safety for the numerous reasons given by Mr. Chance. The latter, however, lays chief stress on the value of the acetylene because of its non-fouling and non-obscuring effect on the atmosphere. Another important advantage over any other form of illumination is the clear, bright light projected at the point where the workman may look for danger. The better illumination materially safeguards the worker against obstacles over which he may stumble when traveling, and against dangers from falls of roof or of coal, weakness in timbering, and similar conditions. The acetylene lamp, where it may be used with safety, has advantages even over the present electric cap lamp, in that it gives a higher luminosity; and when the miner comes to learn its signals, as he will in time, just as he learns those given by the open-flame or the safety lamp, he will find that the acetylene lamp is a fair detector not only of methane but of carbon dioxide, as clearly shown by Mr. Chance. The only, serious objection, raised against the use of carbide lamps. has been recently in Pennsylvania, due to the belief of the State Mine Inspection Department that it endangered miners working on pillar work, or other places where carbon dioxide might accumulate, or where there is lack of sufficient ventilation, and because it was believed that the indications of the carbide lamp would not give the miner sufficient warning. On this point Mr. Chance has clearly shown the fallacies of the objections. I may add that for those unable to detect carbon dioxide with the acetylene lamp, the maximum of protection would be afforded by using an open oil lamp or a flame safety lamp in such places; or, because the miner might not watch his oil light, a better, protection still would be offered by a sufficient number of daily inspections of such working places by a fire boss or other official, with flame safety lamp.

Jan 4, 1917

By H. M. Howe

A Discussion of the paper of Professor Howe, presented at the London Meeting, July, 1906, and printed in Bi-Monthly Bulletin, No. 14, March, 1907, pp. 169 to 274. SECRETARY&apos;S NOTE.-M. Beutter&apos;s introductory remarks, being simply a resume of Prof. Howe&apos;s paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution has been somewhat condensed, without omitting any essential statements. M. BEUTTER, St. Etienne* (communication to the Secretary-+):-Professor Howe observes in paragraph 47 of his paper that the fluid-compression of steel. diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingworth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forgings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without dan¬ger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jul 1, 1907

E. E. Olcott, New York City: Prof. Kemp&apos;s valuable description of the Lancaster Gap mine is in line with many other able contributions on the origin of mineral deposits that the Institute has lately brought forward. The splendid contribution that Prof.

Jan 1, 1895