Search Documents

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By Martti E. Maliniemi

The Svappavaara mine is located 47 km southeast of Kiruna C. The ore deposit now being worked, Leveäniemi, belongs to Luossavaara- Kiirunavaara AB (LKAB) and is the company's, and also Sweden's, third biggest mine after Kiirunavaara and Malmberget. The distance by rail to the Norwegian port of Narvik is 214 km and to Lulei on the Gulf of Bothnia 340 km (Fig. 1). The village of Svappavaara has about 800 inhabitants. The climate is arctic in character. The temperature during the months of December to February is about -20º to -35ºC, and the ground is covered by a blanket of snow for about eight months of the year. The brief, intensive summer often arrives with startling speed, bringing both sunshine and warmth. HISTORICAL BACKGROUND Mining operations took place in Svappavaara as far back as 300 years ago. During the period 1655-1684, copper ore was taken from the deposit called Gruvberget in the vicinity of the village. The total production of raw copper was probably about 1,045 tons. During the 18th and 19th centuries, several attempts were made to extract iron ore from the numerous deposits found within the district. These brave attempts, however, were foiled by the high phosphorus contents and the enormous transport difficulties. The present-day mine fields in Leveäniemi were discovered in 1897. At that time, it was difficult to determine the size and value of the deposit because of the thickness of the soil cover (3 to 15 m) and the

Jan 1, 1969

By H. C. Kenny

The annealing or softening temperature of cold-worked copper is appreciably increased by almost unbelievably small amounts of silver. As indicated by some data in this paper, the softening temperature of high-conductivity, tough-pitch copper may be increased from 200" to 350" C. by the addition of only 15 oz. per ton (0.052 per cent) of that element. Because it has this higher annealing temperature as compared with the silver-free metal, silver-bearing copper finds considerable use in industry. For example, when hard-rolled copper is used in operations that involve soldering or tinning, silver-bearing copper insures against loss of strength, whereas silver-free copper becomes "dead soft." Yet—though several investigators, beginning with Caesar and Gernerl in 1916, have shown that small amounts of silver do definitely raise the softening temperature of copper—data are lacking on the problem: What is the specific influence of different amounts of silver on this temperature? It was to help in filling this gap in the knowledge of what might be termed "alloy coppers" that the data given herein were obtained. The softening of cold-worked copper depends, of course, on a number of factors, of which the composition of the material is only one. Other highly important factors are the degree to which the material is cold-worked and the time it is held at the annealing temperature. The method of cold working and the grain size of the metal produced are also significant. All these variables were taken into account in the investigation reported here, and the influence of silver on the electrical conductivity and on the working was also considered. The coppers used in the softening tests were Lake coppers melted and cast by the Calumet and Hecla Consolidated Copper Co. The ires were fabricated by the Roebling Wire Co. and the sheets were rolled at the Battelle Memorial Institute. Partial analyses of some of the coppers are listed in Table 1, with their electrical conductivities.

Jan 1, 1934

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By J. B. Austin, H. H. Pierce

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By H. H. Pierce, J. B. Austin

In developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measurements serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transformation temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chromium or managanese. The lag, or undercooling, observed at the ? — a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys, which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,' using a rate of heating and of cooling of 3.0" to 3.5" per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2 Results and Discussion Thermal Expansion Coeficients.—Numerical values for the linear expansion coefficient, derived from a smoothed curve based on at least

Jan 1, 1935

By B. H. Kear, S. M. Copley

A dynamic theory of precipitation hardening in alloys containing cohevenl, stvess-.free, ordered particles is developed. The yield stvess is predicted from the stress dependence of the plastic strain vale, which is related to a derived dislocation velocity-stress function. The theory is shown to predict the magnilude and temperature dependence of the yield stress of a commercial nickel-base superalloy as well as many details of its slip structure. GLEITER and Hornbogen have developed a theory of the yield stress in alloys hardened by coherent, stress-free ordered ptrticles based on the observation that dislocations (b = a/2 (110)) glide in pairs.' When a dislocation pair shears through an ordered particle, the glide motion of the leading dislocation is impeded since it must create antiphase boundary (APB), whereas the motion of the trailing dislocation is assisted because it annihilates APB produced by the first one. Taking into account the APB energy, the size, and spacing of the particles, G-H predict the observed yielding behavior in Ni/18.8 Cr/6.2 A1 alloys composed of a matrix phase y '(nickel-solid solution) and particles of y' (basically Ni3A1). The G-H theory, as well as all previous theories of hardening by coherent ordered particles, do not include the details of dislocation motion; the present dynamic theory is an attempt to overcome this limitation. In the dynamic theory, the yield stress is predicted from the stress dependence of the plastic strain rate, which is related to a derived dislocation velocity-stress function. This function can be evaluated if the structure of the alloy, the APB energy of the ordered phase, and the characteristic drag or frictional stresses of the matrix and precipitate phases are known. The theory is shown to account for the observed temperature dependence of the yield stress in a commercial nickel-base superalloy. 1) NICKEL-BASE SUPERALLOYS Although their compositions are complex, the nickel-base superalloys have remarkably simple structures. A detailed examination of the commercial superalloy

Jan 1, 1968

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By Roman Šejnoha, Karel Mazanec

A pronounced tendency for delayed fracture zoas observed in the martensite structure of low-alloy steels in the as-quenched condition. Cracks of predominantly intercrystalline nature nucleated and propagated at stresses substantially lower than the short-titne tensile strength of- the steels, and were observed even in hydrogen-free speciunens. The occurrence of delayed fractures in the as-quenched condition is interpreted as a supevposition of the effect of free dislocations generated during the martensite transforlnation, and of a weakening of the prior austenite grain boundaries caused by dynamic shocks exerted on the boundaries by growing martensite plates. AN important metallurgical problem, connected with the production and use of high-strength steels, is delayed fracture in martensitic structures. Such fractures occur in quenched steels as a result of prolonged loading with external stresses far lower than the short-time tensile strength of the steel. The same effect can be produced by sufficiently high internal stresses: it is well-known that quenched structures will in some cases crack intergranularly at room temperature if not tempered quickly enough even in the absence of any externally applied stress. In Troiano's papers1,2 on delayed fractures in high-strength steels, the fundamental role of hydrogen migrating under the influence of multiaxial stress towards the nuclei of cracks was found. Fig. 1 shows the typical relationship between stress and the time to fracture found by Troiano in hydrogen-charged high-strength steels. On the other hand, Shurakov 3,4 explains the realization of delayed fractures in martensite as due to a "quasi-viscous" behavior of the austenite grain boundaries immediately after the martensitic transformation. 1) MATERIALS AND EXPERIMENTAL METHODS Two low-alloy steels of commercial purity were used for the experiments reported in this paper. Their chemical composition is shown in Table I. The heats were melted in a laboratory furnace, cast to ingots, forged to bars of 3/4 in. diameter, and annealed. Machined test pieces were heat-treated as follows: Ni-Cr-Mo steel held at 900°C for 30 min and quenched in oil; Mn-Si-Cr steel held at 900°C for 30 min and quenched in water. For the delayed-fracture tests, notched cylindrical test pieces, Fig. 2, stressed in torsion, and unnotched cylindrical tensile-test pieces, 1/4 in. diameter, were used. The specimens were normally loaded with a constant static load 45 min after quenching for the torsional tests and 10 min

Jan 1, 1965

By Gordon R. Haworth, J. Terry Aimone

The capital-short mining industry, faced with weak metal markets, will need to devise new and novel methods to finance future expansions.

Jan 9, 1977

AT the Tulsa meeting of the A. P. I., the following reso-lutions, expressive of the policy of that organization, were among those adopted: RESOLVED, That we endorse the conclusion of the Federal Oil Conservation Board in its report of September, 1926, that the prevention of the waste of gas incident to the pro-duction of oil is of paramount importance in the conserva-tion and economical production of oil, and the president of the Institute is requested to appoint a committee of seven to devise and suggest to this board, or the executive com-mittee, such measures as will enable the industry, while continuing to meet the consumption requirements for pe-troleum and its products, to conserve in its natural state such reserves of petroleum as may not then be required for consumption. RESOLVED, That the president of the Institute appoint a committee of seven to formulate and recommend to this board or its executive committee, at the earliest practicable date, a program of legislation; Federal and State, to be advocated by the Institute giving sanction and effect to agreements by oil producers for the curtailment of produc-tion in pools where and during periods when there is over-production, having for their purpose the economical and orderly production of oil.

Jan 1, 1927

By G. A. Vissac

MoIstuRe in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain"). These latter forms of moisture are particularly common in "young" coals (subbituminous and lignites); bloom coals (seam outcrops); fusain; and carbonized products. In our study of coal drying, we shall consider only the removal of free moisture, exclusive from hygroscopic moisture. Dewatering If we reserve the name of drying to the removal of water by evaporation, we must consider the initial phase of the mechanical removal of free moisture as a distinct operation covered by the term dewatering. In all cases the free water carried over the surface of the coal particles or in their interstices, or in their pores, is retained by capillary forces. Dewater-ing is accomplished by breaking or counteracting these capillary forces; removal of as much water as possible by dewatering methods is usually advisable, as the cost of these operations is generally much less than by evaporation. The most common methods of me-chanical dewatering are: 1. "Pressure piling," which reduces the interstitial spaces, accomplished in dewatering bins or over dewatering screens. 2. Or dynamic methods, such as used in centrifuges or over vibrating screens. We shall only mention the " preferential wetting" method, in which surface water can be displaced by hydrocarbons, as offering possibilities, but which, to our knowledge, has not reached yet a practical development. But we must point out that the capillary forces retaining water on the coal surfaces, decrease considerably with increased temperatures. This is the principle used in all modern dishwashing machines; by using very hot water, dishes are extracted almost dry. In line with this development, we favor the type of dryers including a dewatering section; as the coal enters the dryer and is gradually brought up to higher temperatures, its dewatering ability is increased and advantage can be taken of this conditioning, resulting in increased drying efficiencies and reductions in drying costs. Heat Drying In the final phase, the remaining moisture must be evaporated. Coal and water must be brought up to the chosen temperature of evaporation, and heat must be supplied to fill the requirements of the latent heat of evaporation of the water to be removed. Accordingly, drying becomes largely a problem of heat transfer, and drying methods can be classified accordingly, namely: 1. Radiant transfer. 2. Transfer by surface contact and conduction. 3. Transfer by hot gas contact. The first method is not applicable to coal drying; the second method is used in the old type rotary dryer. The third method, the most commonly used in modern coal dryers, will be the only one considered here; and, of course, we shall deal with continuous types of dryers only. The mechanism of complete drying is really very complex-—several phases are involved: 1. The constant rate period. 2. The uniform falling rate period. 3. The varying falling rate period. As most of our practical coal drying problems deal with wet coals (over 6 pct of moisture), and do not require complete drying (under 1.5 pct), we shall deal with the first condition only, namely the constant rate drying. Dryer Calculations Instead of presenting the algebraic formulas, we believe a concrete example will provide a clearer illustration. Assume a feed of wet coal at the rate

Jan 1, 1950

By Salinger, Herbert

WITH the large amount of metallurgical re- search work now being done and the constant effort of the engineer to effect economies of operation, I think it is a safe prediction that the next few years will see a great change in the handling of mine products. The well-managed mine, with sufficient ore reserves to warrant the necessary plants, will increasingly call upon the metallurgist and chemist for the solution of its problems. Shipping sorted ore or concentrate to the nearest smelter will not be the course followed. From ore to metal, or at least to a product directly salable to the consumer, will be the practice followed. As a consequence, mine managers will be increasingly interested in metal trade problems. By metal trade I mean the buying, selling, shipping, handling, and all the practices, forms and customs that go to make up the trade.

Jan 1, 1928

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

By E. C. Carris

THE particular field of application of machines utilizing air cur¬rents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940. They have not found any application for cleaning anthracite. Since the development and introduction of the first successful com¬mercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the Ameri¬can Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Heyl and Patterson oscillating table, 199.7. 4. "Stump Air-Flow," pulsating air jig, 19391. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAN TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corpora¬tion, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By Walter F. Gries

AN ounce of prevention is worth A a pound of cure' is an old proverb that has sometimes been forgotten in programs having to do with the health of workmen. Realization of the truth of this maxim is increasing, however, and today the iron-mining industry, with which I am particularly concerned, is becoming more alive to the prevention of illness and the conservation of health, thus decreasing the need for treatment after diagnosis has established its necessity. The healthy workman is the happy, efficient workman, and new programs tending to make him more health-minded are being put into operation. Preventive medicine is less costly than corrective medicine, to say nothing of the better results obtained. Periodic physical examinations, with close follow-up attention when required, have reduced the time lost because of illness, workmen's compensation costs, and group-insurance benefits for nonindustrial disabilities.

Jan 1, 1939

By Marc W. Bodine

Insoluble residues from three sequences of Paleozoic marine evaporates (Retsof salt bed in western New York, Salado Formation in southeastern New Mexico, and Paradox Member of the Hermosa Formation in southeastern Utah) are rich in trioctahedral clays. Chlorite (clinochlore), corrensite (mixed-layer chlorite-trioctahedral smectite), talc, and illite (the only dioctahedral clay) are the dominant clay minerals; serpentine, discrete trioctahedral smectite (saponite), and interstratified talc-trioctahedral smectite are sporadically abundant. These clay-mineral assemblages differ chemically and mineralogically from those observed in most continental and normal marine rocks, which commonly contain kaolinite, dioctahedral smectite (beidellite-montmorillonite), illite, mixed-layer illite-dioctahedral smectite, and, in most cases, no more than minor quantities of trioctahedral clay minerals. The distinctive clay mineralogy in these evaporate sequences suggests a largely authigenic origin. These clay minerals are thought to have formed during deposition and early diagenesis through interaction between argillaceous detritus and Mg-rich marine evaporate brines.

Jan 1, 1985

By Bernard Kopelman

THE particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by com¬mercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature, and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. REVIEW OF THE LITERATURE Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.1 When reduction of tungsten oxides by H2 was introduced commercially, 2.1 several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-13 While these many investigations were in fair agreement on the equilibria there arose considerable controversy as to the chemical composition of the oxide between W03 and W02, because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 10o years. Thus Malguti,14 in 1835, decided it was W02.56. In 1857, Riche" proposed the formula W308. Usler,16 in 1865, confirmed the existence of W308 and further proposed W4O11. In 1897, Desi17 agreed upon W308 but also found W5014.

Jan 1, 1946

By Stein Wennberg, Snorre Tessem

INTRODUCTION The mine is situated in the middle of Norway 150 km north of the town Trondheim. The iron ore deposits were discovered in 1906 and have been continuously mined since. The first owner was A/S Nordiske Grubekompagni. In 1912 Fosdalens Bergverks-Aktieselskab was established; since World War II it has been a wholly state-owned company. The location is advantageous, with mining facilities, ore dressing plant and stockpile situated near the northern head of the Trondheimsf jord. The iron ore always occurs in Ordovician lavas and sediments, now altered to greenschists, keratophyres and limestone. The ore bearing zone is 150 km long. The deposits consist of two parallel linear ore bodies lying one above the other in the same stratigraphic horizon which dips 70' to the south. The upper body is 50-100 m high, the lower one 250 m high, while the distance between the two bodies in the East mine varies between 20 and 60 m. The ore width varies between 5 and 8 m. The ore bodies strike WSW and plunge between 10' and 15" in this direction. To date continuous ore has either been worked or opened up along a total strike length of 10 km. Until 1969 all ore was mined in the western part of the deposit called the Western mine. In the spring of 1969 production started in a new mine, the Eastern mine. The ore bodies in this new mine are geologically the same as in the old mine, but they have been displaced 700 m downwards along a major fault in the Fosdalen valley.

Jan 1, 1981

NEW MEMBERS The following list comprises the names of those persons who became members during the period of June 10, 1918, to July 10, 1918. ALLPORT, JAMES H., Cons. Engr Barnesboro, Pa. ANDERSON, G. E., Engr., Exploration Dept., American Smelt. & Refin. Co.,Tucson, Ariz. BAKER, HARRY A., Capt., Co. M, 53d Pioneer Infantry, Camp Wadsworth, Spartanburg, S. C. BEALL, ROBERT STEPHENS, Supt., Empire Zinc Co. (of Colorado), Canon City, Colo. BLAYLOCK, SELWYN GWILLYM, Mina & Met. Engr., Asst. Gen'l Mgr., Cons. Min. & Smelt. Co. of Canada, Ltd., Trail, B. C., Canada. BOTTERILL, THOMAS CLARK, Min. Engr., Belmont Surf Inlet Mines, Ltd., Surf Inlet, B. C., Canada. BOWMAN, MAURICE Asst. Supt., New Idria Quicksilver Min. Co., Idria, San Benito Co., Cal. BROOKS, EARL W Chief En r. Inland Collieries Co. Harmarville Pa. BROWN, DEWITT W Chief Chem., Prime Western Spelter Co., Iola, Kansas BUISSON, ARTHUR Min. Engr., Dept. of Mines, Sussex St., Ottawa, Canada. BUNYAN, F. W Chem., Southern Pacific Railway Co., Sacramento, Cal. BURNETT, ARCHIBALD Supt., Swansea Lease Inc., Swansea, Ariz. BURTON, GEORGE E., Resident Geol., Empire Gas & Fuel Co., Varsity Shop Bldg., Norman, Okla.

Jan 8, 1918