Search Documents

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper' shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.'-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.' Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By A. Lubinski

In drilling operations, attention generally is given to hole angles rather than to changes of angle, in spite of the fact that the latter are responsible for drilling and production troubles. The paper presents means for specifying maximum permissible changes of hole angle to insure a trouble-free hole, using a minimum amount of surveys. It is expected that the paper will result in a decrease of drilling costs, not only by avoiding troubles, but also by removing the fear of such troubles. SUMMARY, CONCLUSIONS AND RECOMMENDATIONS Excessive dog-legs result in such troubles as fatigue failures of drill pipe, fatigue failures of drill-collar connections, worn tool joints and drill pipe, key seats, grooved casing, etc. Most of these detrimental effects greatly increase with the amount of tension to which drill pipe is subjected in the dog-leg. Therefore, the closer a dog-leg is to the total anticipated depth, the greater becomes its acceptable severity. Very large collar-to-hole clearances will cause fatigue of drill-collar connections and shorten their life, even in very mild dog-legs. Another finding regarding fatiguing of collar connections in dog-legs is that rotating with the bit off bottom sometimes may be worse than drilling with the full weight of drill collars on the bit, mainly in highly inclined holes when the inclination decreases with depth in the dog-leg. Means are given for specifying maximum dog-legs compatible with trouble-free holes. An inexpensive technique proposed is to take inclinometer or directional surveys far apart; then, if an excessive dog-leg is detected in some interval, intermediate close-spaced surveys are run in this interval. The application of the findings should result in a decrease of drilling costs, not only by avoiding troubles, but mainly by removing the fear of such troubles. The result would be much more frequent drilling with heavy weights on bit, regardless of hole deviation. Because of errors inherent to their use, presently available surveys are not very suitable for detecting dog-legs. There is a need for instruments especially adapted to dog-leg surveys. Crooked hole drilling rules should fall into two distinct categories—(1) those whose purpose is to bottom the hole as desired, and (2) those whose purpose is to insure a trouble-free hole. Three kinds of first-category rules in usage today are as follows. 1. A means to bottom the hole as desired is to prevent the bottom of the hole from being horizontally too far from the surface location; this may be achieved by keeping the hole inclination below some maximum permissible value such as, for instance, 5. 2. Another means to achieve the same goal is to limit the rate at which the inclination is allowed to increase with depth. A frequently used rate is 1/1,000 ft. In other words, a maximum deviation of l° is allowed at 1,000 ft, 2 at 2,000 ft, 3 at 3,000 ft, etc. 3. Whenever application of the first two means precludes carrying the full weight on bit required for most economical drilling, then the best course is to take advantage of the natural tendency of the hole to drift updip, displace the surface location accordingly and impose a target area within which the hole should be bottomed. This method has already been successfully applied,'.' and its usage probably will become more frequent in the future. Means for calculating the amount of necessary surface location displacement are avail-able.3'5'6 If in high-dip formations the full weight on bit should result in unreasonably great deviations, the situation could be remedied by increasing the size of collars and (if needed) the size of both hole and collars,351 or in some cases by using several stabilizers. Rules which would fall into the second category (i.e., rules whose purpose is to insure a trouble-free hole) are seldom specified today. It is vaguely believed that following Rules 1 and 2 of the first category will automatically prevent troubles. Actually, this is not true. If at some depth the only specified rule is that the hole inclination must be less than 4", the hole may be lost if the deviation suddenly drops from 4 to 2, or if the direction of the drift changes, etc. Rule 3 of the first category is generally used in conjunction with a rule belonging to the second category, namely, that the hole curvature' (dog-leg severity) must not exceed the arbitrarily chosen value of 1½ /100 ft. Moreover, when using this rule, the industry is not clear over what depth intervals the hole curvature should be measured. All this results in a frequent fear

By J. Washburn, R. Drouard, E. R. Parker

Temperature dependence of the rate of recovery in zinc single crystals after a simple shear deformation at low temperature was investigated. Some tentative suggestions regarding the annealed and strain-hardened states of a crystal are discussed. RECOVERY may be defined as the gradual return of the mechanical and physical properties of strain-hardened metal to those characteristic of the annealed material; an increase in temperature increases the rate of recovery. The annealing process in strain-hardened polycrystalline metals is complicated by the inhomogeneity of strain which always exists in aggregates. Polygonization in bent regions of the crystals and growth of new almost strain-free grains starting at points of severe local distortion1-:' make it almost impossible to isolate and study the recovery process. Homogeneously strained single crystals, however, do not polygonize or re-crystallize and hence they can be used advantageously to study recovery. In such crystals strain hardening is completely removed by recovery alone. Since recovery is a process whereby certain lattice disturbances introduced by plastic flow are gradually reduced, a knowledge of the rate and temperature dependence of this process for various conditions of prestrain might be helpful in formulating a model of the strain-hardened state. For simplicity it seemed desirable to limit the type of prestrain to the simplest obtainable, i.e., simple shear strain. In the experiments to be described, recovery was studied by observing changes in the stress-strain curve of prestrained zinc single crystals held for various times at temperatures above that employed for straining. Single crystals were grown from the melt by a modified Bridgeman technique from Horse Head Special zinc 99.99 pct pure, and from spectrographically pure zinc 99.999 pct pure. They were grown as 1 in. diameter spheres and acid-machined' to the final specimen contour. The test section was a cylinder about 1/8 in. high and 3/4 in. in diameter. The conical sections adjacent to the test section were cemented into the grips so the load could be transmitted to the crystal as uniformly as possible. The specimens were oriented so that in testing the maximum shear stress was applied along one of the slip directions, [2110], in the (0001) plane. Details of the production and testing of such specimens have been presented.' Each test was carried out according to the following schedule: 1—The crystal was strained at — 50°C until it reached a maximum shear stress, ,,,. The strain rate was approximately 5 pct per min in all cases. 2—After straining, the crystal was unloaded before the temperature was changed. Unloading required about 3 min. 3—The temperature of the specimen was then increased from — 50°C to the temperature, T, of recovery. This change in temperature was completed in a time of less than 2 min. The specimen remained at temperature, T, for a time, t, which differed for the various specimens. 4—Thereafter the temperature was again reduced to — 50 °C in approximately 3 min. 5—While at —50°C, the stress-strain curve after recovery was obtained. 6—The specimen was then unloaded and annealed for 1 hr at 375 °C in a helium atmosphere to bring about complete recovery. Cooling to room temperature after anneal required 90 min. 7—The same crystal could be re-used for another test because the plastic properties after annealing closely duplicated those of the original crystal. The specimen was immersed during the test in a bath of methyl alcohol which, through a system of tubes, could be pumped through either of two heat exchangers to regulate the temperature; this was accomplished by circulating the liquid through coils immersed in a bath of acetone and dry ice for cooling or in a bath of warm water for heating. Test temperatures were thus maintained constant within ±1°C. The — 50°C temperature was low enough so that no measurable recovery occurred during unloading and reloading. The stress-strain curve continued after recovery along a path below, but approximately parallel to, the path of a curve obtained in an uninterrupted test. Fig. 1 shows some of the results from a specimen of 99.999 pct Zn. The amount of downward displacement of the curve due to recovery was a

Jan 1, 1954

By I. Tamura, J. O. Brittain, T. Mura

Plain carbon steel in the cold worked or marten-sitic conditions has an internal friction peak at about 250 oC at a frequency of I cps. The influence of substitutional alloying elements on this peak was examined experimentally. The alloys were vacuum melted Co-, Cr-, Mo-, Ni-, and Si-iron (about 3 pct alloying elements), and carburized Si-iron. The internal friction of the alloys in the temperature range 30o to 500 OC was determined by means of a torsion pendulum. The 250 oC peak of the cold-worked alloys was lower in height than that observed in plain C-iron and steel. Carburized Si-iron in the quenched condition had a peak which occurred at a slightly lower temperature than in quenched plain C-steel, but the height of the peak was substantially greater than that found for the same alloy in the cold-worked condition. The activation energy of this peak for martensitic Si-steel was about 35 kcal per mol. ANNEALED a iron has two internal friction peaks due to nitrogen and carbon at 20o and 40o C respectively, at a frequency of 1 cps. If a iron is cold worked, these diffusion peaks become smaller and a new peak appears at about 250o C. The activation energy for the 250o C peak is in the range of 32 to 44 kcal per mol and has an average value of 38 kcal per mo1. It has been experimentally verified that both interstitial solute atoms and dislocations are necessary for the 250o C peak. 3 Wert has also shown that an incubation period precedes the appearance of the 250 C peak.4 With regard to quenched martensitic steel, Ke et al.596 observed two peaks at around 130o and 250o C. They conjectured that the 250o C peak in martensite was due to the same mechanism as the 250°C peak in cold worked a iron, and the 130°C peak was due to the nature of tempered martensite. They did not report the activation energy for these peaks. Chernikova7 found only one peak at about 200° C in tempered martensite. In a previous paperS we reported an activation energy of approximately 40 kcal per mol for the 250° C peak in plain carbon martensitic steels. Ichiyama8 found the activation energy to be about 36 kcal per mol for the 250° C internal friction peak in steels in the martensitic condition. The present authors proposed a theory for the 250°C peak for cold worked and quenched iron and steel.= The theory for the peak is based upon the addition of a strain-energy term to the free energy for the formation of a carbide precipitate due to the presence of a disclocation. The model employed for the relaxation process consists of the growth and solution of a carbide precipitate of critical size as a consequence of an oscillating dislocation. In this report, the influence of substitutional alloy ing elements on the 250° C peak is examined and the experimental results are discussed in terms of our theory for the peak. Most of the experimental work on the alloy steels was confined to the Fe-Si-C alloys.

Jan 1, 1962

By L. Hartsell Cash

INTRODUCTION Created in 1944 to help rebuild those economies, principally in Europe, which were seriously damaged or destroyed during the Second World War, the World Bank--or to use its correct name, the International Bank for Reconstruction and Development-began its operational phase by making a loan to the Government of France to accomplish two tasks: (i) to import coal for space heating purposes; and (ii) to buy new machinery and equipment to help rehabilitate its coal mines. Once the thrust of reconstruction in postwar Europe was largely accomplished, the World Bank Group (for today the World Bank has three separate lending windows) turned to mobilizing funds to improve living standards in developing countries, which remains its primary goal today. Over this period of time, the World Bank Group has continued to assist the world mining industry in various ways and, since 1955 the World Bank Group has financed mining or mineral processing projects with loans/credits totalling $1.5 billion. The World Bank Group consists of two institutions--the World Bank itself and the International Finance Corporation (IFC), which was founded as a separate institution in 1956 and three separate lending windows--the World Bank, the International Development Association (IDA), and IFC. The World Bank loans are provided at commercially-related interest rates but have grace periods usually of up to 3 to 5 years and repayment periods ranging from around 15 to 20 years. Since the World Bank raises its operating funds on the international capital markets in varying currencies and in varying interest rates, it relends a basket of currencies at floating interest rates which are fixed every six months to reflect the Bank's own borrowing cost. At the present time, the interest rate is just below 10% per year and in addition, a one-time front-end fee of 1/4 of 1% is charged. Also, a commitment fee of 3/4% per year is charged on the undisbursed amount of the loan itself. For loans to industrial and mining projects, it is normal to charge an additional guarantee fee of 1 to 1.5% in addition to the annual interest rate. This guarantee fee is payable to the government of the country in which the project is carried out since, by its charter, the World Bank is required to have the guarantee of the host government for each loan made in a specific country. By far the greatest source of lending funds within the World Bank Group is that of the World Bank itself and for the fiscal year ending June 30, 1984, the World Bank approved loans totalling $12 billion. The second lending window within the World Bank Group is IDA which performs the same functions as the Bank itself and has the same staff. Nevertheless, its loans (called credits) are made on much softer terms and are made to the poorest nations only. IDA funds are subscribed by the wealthier countries, usually as grants, and these are relent as credits to those countries with the lowest per capita income. IDA credits are made for 50 year periods, including 10 years of grace, to the government itself. The credits are interest free, but there is a service charge of 3/4% per year on the amount withdrawn and outstanding to defray the administrative costs of IDA. Credits approved during fiscal 1984 totalled $3.5 billion. The third lending window is IFC. While IFC is a separate corporation and operates quite separately from the World Bank and has its own staff and regulations, it works very closely with the World Bank on its overall approach to the mining sector and to a particular country. IFC's mission is essentially to supply venture capital and to stimulate development of the local private sector in capital markets as well as to promote the international flow of private capital to developing countries. Unlike the World Bank and IDA, the IFC does not lend directly to governments

Jan 1, 1985

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940's it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By L. Zwell, H. A. Wriedt

X-ray Lattice parameter and bulk density measurements were made at room temperature on solid solutions of nitrogen in purified a, iron, containing from 0 to 0.053 wt pct N. When nitrogen is dissolved in a, iron, the fractional increase in unit cell volume (X-ray diffraction) and the fractional increase in volume per gram of iron (bulk density measurement) are the same within experimental error. The two sets of results when averaged show that the unit cell edge of a, iron increases linearly by 3.2 X 10-2 A per wt pct N dissolved and that the partial gram-atomic volume of nitrogen at infinite dilution in a, iron is the same as it is in nitrogen-martensite, that is, 5.90 cm3. RECENT reviews17' of literature dealing with the lattice parameter of ferritic iron-nitrogen alloys indicate that the dilating effect of dissolved nitrogen on the bcc unit cell of a iron is not known with confidence. Five investigations3-7 either revealed no effect of nitrogen or were inconclusive. Among other investigations, where quantitative data were obtained, the results of Osawa and Iwaizumi8 indicate too large an effect, and those of Eisenhut and Kaupp9 show the lattice parameter of ferrite varying with the nitrogen content at concentrations far beyond the known solubility limit. It is not clear in Burns'10 data what value should be used for the lattice parameter of nitrogen-free ferrite in calculating the dilation. Burdese11 shares with Burns the shortcoming that the iron-nitrogen alloys were solution-treated and quenched with undissolved nitride present. The consequence is that the un- certainties in the solubility limit1 are added to those in the lattice parameter measurements when the variation of lattice parameter with nitrogen content is computed. For a system of such widespread interest, we felt that a new investigation was merited. Both X-ray diffraction and bulk density measurements were used to determine the dilation of the , a iron lattice by dissolved nitrogen. EXPERIMENTAL PROCEDURE Material. The bulk density and X-ray diffraction experiments were both made with specimens of a purified iron (denoted as "B iron")- from Battelle Memorial Institute. The impurity contents were as follows: As, C, Cu and Pb—50 ppm; Ag, Al, Co, Ga, 0, Ti-11 to 50 ppm; B, Be, Ca, Cd, Cr, Mg, Mn, Mo, N, Ni, S, Sb, Si, Sn, V, W-10 ppm or less. The vacuum-cast ingot was hot-forged and annealed. Pieces of the forged stock were machined and cold-rolled to give strip stock 0.08 and 0.002 in. thick for density and for X-ray measurements, respectively. Preparation of Specimens. Starting with a piece of the cold-rolled iron stock, the general sequence of operations, after an initial recrystallizing anneal, was to measure the density or lattice parameter, nitrogenize, remeasure the property, age or denitrogenize, and again measure the property. Duplicate analyses for nitrogen were made by a modified Kjeldahl method on portions of the actual density specimens and on pieces nitrogenized to equilibrium alongside the X-ray specimens. Annealing of the density specimens was performed by sealing the pieces with the as-rolled surfaces removed by filing into evacuated "Vycor" capsules and treating for 1 hr at 750°C followed by furnace cooling. (TO check the effect, if any, of annealing procedure, a specimen also was

Jan 1, 1962

By Frank Hall

THE needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. So patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are manipulated so as to give the greatest strength.

Jan 1, 1920

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By Sidney Siegel, J. Gardner Brooks, Irvin R. Kramer

IN 1942 Grossmann1 proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigators2-5 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent [ ] upon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a hite quench than predicted by Grossmann's factors for an infinite quench (Table I). [ ] Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Grossmann's grain-size correction curves, deter- mined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1946

By C. S. Matthews, H. C. Lefkovits

The performance of depletion-type reservoirs at the stage in which the gas is at such low pressure that gravity is essentially the sole driving force has been investigated both theoretically and by use of scaled models. A simple theory is developed which completely explains the scaled model experiments. It also agrees with some field data. When the range of production rates to be considered is less than 25, the theory predicts that the production rate decline curve for homogeneous reservoirs in which there is a free surface will be of the hyperbolic type with n = 2: The theory gives a physical significance to the parameter y. INTRODUCTION This investigation was undertaken to determine a method for prediction of performance of reservoirs where gravity is the sole driving agent. Depletion-type reservoirs fall into this category after the pressure has fallen to some low value. Some examples of this type are found at Healdton ('Oklahoma), Oklahoma City (Oklahoma), Midway-Sunset (California), and East Coalinga (California). Generally the production rate per unit thickness is quite low in such reservoirs, with the conse- quence that this stage is sometimes called the stripper stage. However, per well production rates may be of the order of 50 B/D because of the considerable sand thickness open in some of the reservoirs. In the past, predictions of behavior of such reservoirs have been based on empirical extrapolation of the rate of production to the economic limit. Difficulties arise when new wells are drilled in the field or when production is artificially curtailed, since in such cases the decline rate of individual wells or leases changes and no clear trend can be detected. It was hoped that the present study would lead to improved methods for evaluation of such reservoirs. The study was initiated by building a scaled model for a particular field and by running a number of experiments on this model. Later a simple theory was developed which explained the laboratory results completely. The theory led, as shown below, to a hyperbolic-type decline equation which had been used previously' in a completely empirical manner. THEORY The General Case The problem to be treated here is the following: We are given a homogeneous cylindrical porous reservoir with exterior radius r, wellbore radius r., and height h,, containing, from the bottom up to a height hit oil, some gas, and interstitial water (see Fig. 1 A). The portion of the reservoir between K, and h, is filled with gas at low pressure, with residual oil, and with interstitial water. If at a time t = 0, the level of the oil in the wellbore is lowered to a height h,, what is the production rate from the reservoir at a time to The configuration within the reservoir at some instant

Jan 1, 1957

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

BULLETIN 177. The decline and ultimate production of oil wells with notes on the valuation of oil properties, by C. H.- Beal. 1919. 84 pp., 4pls., 80 figs. BULLETIN 179. Abstracts of current decisions on mines and mining, reported from September to December, 1918, by J. W. Thompson. 1919. 166 pp. TECHNICAL PAPER 214. Motor gasoline; properties, laboratory methods of testing, and practical specifications, by E. W. Dean. 1919. 33 pp., 2 figs. TECHNICAL PAPER 219. Combustion and flue-gas analysis, by U. S. Fuel Administration. 1919. 12 pp., 5 figs. TECHNICAL PAPER 223. Cost-keeping for small metal mines, by J. C. Pickering. 1919. 46 pp. Only a limited supply of these publications is available for free distribution. Publications should be ordered by number and title. Applications should be addressed to the Director of the Bureau of Mines, Washington, D. C.

Jan 7, 1919

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg2SiO4) and fayalite (Fe2SiO4) in solid solution. The name olivine was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Olivine is the principal component of the rock dunite, which itself is a member of the peridotite group of ultrabasic igneous rocks. European uses of the terms olivine and dunite are somewhat different than US usage. In commerce European usage defines dunite as containing 36 to 42% MgO, 36 to 39% SiO2, and loss on ignition of approximately 10%. The term olivine is used to designate a material containing approximately 85% forsterite, with a chemical composition of approximately 45 to 50% MgO, 40 to 43% Si02, 5 to 8% Fe2O3, and ignition loss of 1 to 2%. Uses The principal use of olivine is in various applications involving hot metal. Table I shows the best estimate available as to the amount of olivine consumed by various industries worldwide. In excess of 90% of world uses involve hot metal, with approximately 75% as a slag conditioner in the blast furnace production of pig iron. Approximately 15% of total olivine usage is as a special foundry sand in mold making for the brass, aluminum, magnesium, and manganese steel foundries (Schaller, 1957, 1958; Snyder, 1957; Anon., 1977). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as hand-cobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, has found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). The use of olivine as an additive in the blast furnace is relatively new, having been developed during the last decade. J.W. Currier (Private communication, 1978) describes the behavior of olivine in the blast furnace as follows: Olivine (Mg, Fe2, Si04) represents a unique lime-free source of magnesia and silica as a blast furnace charge component. Only recently has the magnesia-rich mineral been recognized as beneficial cleaner for blast furnace experiencing the problems associated with excessive alkali inputs and/or low coke stabilities. For some time it has been known that alkalis tend to recycle and accumulate in blast furnaces. In the high temperature region of volatilization the elemental alkalis formed attack the integrity of the graphite structure. This alkali attachment is enhanced when poor coke is used. Higher in the furnace stack volatile alkali cyanides condense and oxidize. This accumulation of alkalis tends to agglomerate the burden materials, producing scabs and scaffolds. These structures not only inhibit the downward movement of burden materials and the upward passage of wind, but also lead to erratic furnace performance

Jan 1, 1983

By Geo Ashley

THE following paper is intended to be suggestive only, and to open the way for discussion and further observation. Its preparation was requested only two days before the time limit set for the submission of the papers comprising this symposium. Thus no time existed for detailed studies so it is largely a memorandum of such facts as have come incidentally to the notice of the writer in the study of coal in the field. The field study of sulfur in coal has received very little special attention or description from coal students. The presence of sulfur concretions is noted in hundreds of descriptions, and certain benches of a coal bed may be described as "sulfury" or the presence and position of sulfur bands may be noted in coal sections in connection with sampling. It may be accepted that some sulfur is present in all coal. The amount varies greatly in different regions, in different beds, and in the same bed in different areas. The anthracite of Rhode Island comes the nearest of any coal known to the writer of being free from sulfur, several analyses of that coal showing less than 0.1 per cent. Subbituminous coals in Colorado in a few places have close to 0.2 per cent. of sulfur on the dry-coal basis and in other states subbituminous coals approach this lower limit. Bituminous coals seldom run under 0.4 per cent. of sulfur on the dry basis, though in a few places dry bituminous coals in Colorado and Washington have between 0.3 and 0.4 per cent. The better known bituminous coals have almost everywhere over 0.4 per cent. The best of the Pocahontas and New River coals run close to 0.4 per cent., but there is very little commercial coal in Pennsylvania, Ohio, Indiana, Illinois, Kentucky, or the other states that runs under 0.5 per cent. on the dry basis. From these minimum figures, the amount will range up to 5 or 6 per cent. or higher if visible sulfur is not excluded. It must be remembered that the usual -analysis of a coal bed is not intended to give the total proportion of sulfur in the bed but the amount in the coal after the removal of the more obvious and larger sulfur masses.

Jan 9, 1919

By C. G. Dunn

IDENTIFICATION Of the kinds of orientation relationships that may exist among crystals is an important problem in the metallurgical field. As an aid to its solution standard orientations of several orders of twins would be very useful for rapid analyses to discover high-order as well as low-order twin relationships. Although data have been published that give orientations for three generations of twins, these data are not readily useful in the form presented; i.e., in a stereographic projection with one pole per orientation.1 However, accurate data based on calculations of the positions of all {100} planes for such groups would be very useful when presented in tabular form. Therefore, calculations have been made for a group of four orders of twins and the data are listed in Table 3. Illustrative applications are considered briefly, with the idea of pointing out what may be done with large groups of orientations. METHOD OF COMPUTING ORIENTATION OF A TWIN It is common practice to describe the orientation of a crystal in terms of the positions on a stereographic net of the poles of certain planes of the crystal. A single position on a net may be given it terms of two angle variables, two sets of which appear in the following equations: [Polar NetWalff Net x=rsinOocos4pyx=rcos0. y=rsinB,sin4,ny-rsin0.cos¢,, z=rcos0,,z=rsin0.sin4,,] The three numbers x, y and z determine a length r as well as a direction [(0, 0)] in an X, Y, Z coordinate system. In the present case, r will be set equal to (h2 + k2 +12)1/3, where h, k and 1 are the usual Miller indices for a crystallographic plane, a restriction that facilitates determination of the positions of poles of new planes from those of old or known ones,2 as will become evident later. Furthermore, since twinned lattices have certain planes in common, it is an easy matter to determine the orientation of a twin of a crystal if the orientation of the crystal itself is known. We start therefore with a crystal of known orientation (positions of three {100} poles given) and determine where the cube poles occur in first, second, third and fourth-order twins. Methods for identifying twinned lattices and for making the calculations to find the orientation of a twin have been published.3 4 Reference 4 will be illustrated in the calculation of the orientation of a twin, even though this method differs from the one used by the writer in obtaining the following data on four orders of twins. Consider a crystal S and its twin A1, A1 being one of the four {112} or {III}

Jan 1, 1945

By R. W. Ludt, C. C. DeWitt

The use of froth flotation for the separation of minerals has become one of the most important of ore dressing processes. Its particular adaptability to the enrichment of low grade ores has made the process an important factor in the national economy. The methods have been extended to the recovery of a great number of minerals. Among the few minerals which have resisted efforts toward industrial flotation is chrysocolla, a hydrated partly colloidal copper silicate. Chrysocolla, being a product of natural oxidation, has been found to occur in small quantities with many ores which are recovered by flotation methods. In present practice, these small quantities of copper silicate pass off with the tailings and are lost. The advantages to be gained by a satisfactory process for the recovery of chrysocolla is apparent. Any application of principles which points a way toward the satisfactory industrial flotation process for copper silicate would be of advantage. This paper presents an attack on this problem. Two methods for the recovery of chrysocolla have been developed by the United States Bureau of Mines.1,2 They have been successful on a laboratory scale but have been seriously restricted in industrial application by critical requirements in the procedure. In one of the Bureau of Mines methods,' the ore is activated with sodium or hydrogen sulphide in an aqueous solution at a pH of 4. Amy1 xanthate is then used as a collector with pine oil as a frother in the flotation process. An excess of sulphide acts as a depressant and the state of optimum conditions is difficult to control industrially. In the second Bureau of Mines method,2 soap is used as the collector at a pH of between 8 and 9. The diffi- culties with this process are that soap is not a specific collector, that heavy metal or alkaline earth ions cause the formation of insoluble soaps, and that a more acid solution causes the formation of a free acid which does not act as a collector for chrysocolla. The problem of recovering chrysocolla by flotation involves the selection of a suitable collector. The collector molecule must be composed of an active polar group that has an attraction for chrysocolla, and of a hydrocarbon chain. Certain dyes have been shown to have an attraction for certain minerals. Suida3 found that hydrated silicates are colored by basic dyes. Dittler4 showed that chrysocolla, among other colloidal minerals of acid reaction, preferentially takes up such basic dyes as fuchsin B, methylene blue, and methyl green. Endell5 gave information to show that the colloidal material in clay may be determined by its selective adsorption of fuchsin. A simple experiment, likewise, illustrates the difference in the adsorptive power of chrysocolla and of silica for the basic triphenyl methane dyes. When a mixture of chrysocolla and silica is immersed in a very dilute dye solution, less than 5 ppm, the chryso-colla is rapidly dyed and the silica is dyed more slowly. The difference is substantial but one of degree. Dean2 showed that the dyes, crystal violet and toluidine blue, are taken up by quartz in an adsorption type process. The difference in the adsorptive power, however, offers the means by which a new collector may act. To form such a collector, a hydrocarbon chain must be attached to the dye molecule. This involves a process of organic synthesis. Butyl, hexyl, and octyl hydrocarbon chains were selected for substitution in the malachite green molecule. For the purpose of identification, the alkyl-substituted dyes formed are called: butyl-malachite green; hexyl- malachite green; and octyl-malachite green. An outline of the procedure for their synthesis is given in the appendix. It is generally recognized in the preparation of this type of dye that the chemical structure of some of the dye molecules varies. However, a uniform formula is attributed to the dye. Such a procedure has been followed in specifying the structure of these alkyl-substi-tuted malachite green dyes. The structure is given on the basis of their properties as an homologous series of dyes, on their method of preparation, and on the purity of intermediates used. Structure of substituted alkyl malachite green is: C6H4 N(CH3)2 p-R C6H4 CH C6H4 N(CH)2 Procedure The flotation cell is a Bureau of Mines 100-g, batch unit provided with an air inlet at the bottom above which is a variable speed agitator. The agi-

Jan 1, 1950

By A. B. Kinzel

Since the exposition of the behavior of certain iron alloys by Sykesl involving the existence of an austenite loop and the discovery of such a loop in the chrome-iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MateRial The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic iron and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in. in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.