Search Documents

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By J. R. Long, C. E. Armantrout, A. H. Roberson, T. R. Graham, R. S. Dean

THE general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing 10 to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heusler1 recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and io per cent Al but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 [ ] has drawn a hypothetical boundary for the alpha field with few data to support such construction. The binary systems involved have received considerable attention by numerous investigators, and their general features are well established. The hopper-aluminum system (Fig, I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smiths established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig. 2) has been recently reviewed by Dean and co-workers.7 Using high-purity alloys, they place the solubility of alpha man-

Jan 1, 1946

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.‡ Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; 2.3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

By W. J. Tait, A. E. Craig, E. P. McCurdy

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By E. P. McCurdy, W. J. Tait, A. E. Craig

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By Norman Hedley, George Barsky, S. J. Sawinson

The cyanidation of precious-metal ores is a complex chemical process. Numerous reactions occur, some of which cause an undesired consumption of alkali and of cyanide. A knowledge of these reactions, their products, and the factors that influence the rates at which they proceed should be of value in working out the most economical conditions for cyanidation; but at present, much of this knowledge is lacking. This paper is confined to a study of some of the fundamentals of cyanidation. At the start of such an investigation it is necessary to simplify the problem under consideration by eliminating as many variables as possible. The results are then, of course, not immediately applicable to practice, but it is hoped in further work to round out the information and thereby make it of more practical value. For convenience in presentation, the paper has been divided into two parts, one devoted to a study of the reaction between cyanide and gold or silver, the other to a consideration of the factors that determine the rate of dissolution. I. REACTIONS INVOLVED IN DISSOLUTION OF GOLD AND SILVER IN DILUTE CYANIDE SOLUTIONS Ever since the cyanide process for gold and silver extraction was introduced there has been discussion of the equation representing the reactions involved. In undertaking a detailed study of these factors, it was felt that the most logical first step was to determine, if possible, what reactions could theoretically take place when gold and sill-er are dissolved by dilute cyanide solutions. It is possible to determine whether or not a given reaction will theoretically take place by calculating the free energy of the reaction. This free-energy value for any given reaction is the algebraic sum of the free energies of formation of each of the reactants and products, and, if these values are known, the calculation is simple. (A chemical change always involves an energy change and the amount of energy change involved is the factor determining whether a given reaction will take place or how far it will go. In chemistry we consider what is known as the "free energy"; that is, the maximum amount of energy that can be utilized as

Jan 1, 1935

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,&apos;. &apos; Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.&apos; Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650&apos; to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By G. J. Armstrong, K. S. Lynch, C. G. Thomas, L. A. Baker, R. J. Cornelius

The presence of geothite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18-in. deep bed of green balls, the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind, and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1974

By F. C. Kelley, L. L. Wyman

In order to clarify and amplify the existing data concerning the action of the cementing material in cemented tungsten carbide alloys, the authors have initiated this investigation of the entire range of cobalt-tungsten carbide alloys. Inasmuch as the ultimate objective is relative to what actually goes on during the sintering of cemented tungsten carbide materials, this work was necessarily restricted to heat treatments similar to those used in actual production of these materials. In the course of numerous experiments, the authors have noted several conditions that indicated that there was a solubility to be considered. Among these factors are the following: 1. Many of the alloys showed a much larger amount of binding constituent to be present than could possibly be accounted for by the cobalt content. 2. In many areas, grains of the carbide constituent are much larger than the particles of carbide originally added. In addition, these grains are of very regular contour. 2a. In samples of cemented tungsten carbide which had been fused in the atomic hydrogen torch in the presence of excess binder constituent, immense grains are formed, and their shapes are very regular. This is also true when the cemented tungsten carbide of 13 per cent. Co content is fused alone in the atomic hydrogen torch. Contrary to general expectation, chemical analysis of this material, after fusion in the atomic hydrogen torch, checks the analysis of unfused material. 3. In making the cemented tungsten carbide materials by the process of exerting the pressure at the time of heating a certain portion of the &apos; contents squeezed out of the mold. Chemical analysis has shown that this material contains approximately 12 to 20 per cent. of tungsten. The microstructure shows a cored dendritic structure interlaced with eutectic network, and some graphite, as shown in Fig. 1. 4. Thermal analysis of these materials has consistently indicated an arrest point close to 1350" C.

Jan 1, 1931

By P. P. Gregory

NATURAL petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the ``pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the con-trolled methods of production and drilling, a portion of this gas is pro-duced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a-given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grog rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures were increasing.

Jan 1, 1938

By R. O. Williams

Measurements have been made of the internal energy of deformation in a Cu-A1 alloy and a Cu-Zn alloy as the deference between the work and the released heat. The method required the rapid compression of samples to reduce thermal interactions. The rate of energy storage is low initially but then becomes almost linear with strain. Both alloys stored about 60 cal per mole at a strain of 0.4 in the recrystallized condition. The fractional rate of storage increases at low strains reaching about 0.25 at a strain of 0.15 and then decreases slowly with increasing strains. As do pure metals, these alloys release appreciable energy immediately following deformation; in contrast with pure metals, however, the release continued for extended periods of time. This energy release is somewhat sensitive to the amount of deformation, the deformation temperature, and prior thermal & eatment. It is believed that this release is a composite of that observed in pure metals which has been attributed to dislocations and that due to the motion of vacancies which produces increased short-range order. IT is expected that changes brought about by deformation of a pure metal can be understood in terms of the three defects—dislocations, vacancies, and interstitials—along with the interactions possible between these defects. Frequently stacking faults are created and must also be considered. 1t is not immediately clear whether or not the stress fields which are created should be regarded as independent of dislocations. For alloys there is the important additional effect of atomic configuration, for example short-range order, which must also be considered and will, in general, interact with each of the above defects. While it is true that a complete understanding of pure metals is not yet possible, it would seem very valuable to establish the similarities and differences between pure metals and alloys. Such knowledge could contribute to the understanding of both. A study of the changes in internal energy resulting from deformation of two alloys is reported here. Although some information has been available for alloys almost as long as for pure metals, the volume of work has been substantially less. Sato&apos; and Quinney and Taylor&apos; were responsible for the earlier work, both using brass and annealing calorimetry. tizhnova&apos; studied stored energy in Cu-Ni alloys by a method somewhat similar to the one reported here. Bever and his co-workers have made extensive studies of Au-Ag alloys4&apos;5 and more recently CU-AU&apos;U&apos; using solution calorimetry. Clarebrough et a1.&apos; have recently studied brass using annealing calorimetry. EXPERIMENTAL METHOD The present results were obtained by the rapid, adiabatic compression of a sample about 1/4 in, diam by 1/2 in. long between two tungsten carbide hammers. A vacuum provided thermal isolation and oil provided effective lubrication between the sample and hammers. The increase in internal energy is the difference between the mechanical energy and the heat liberated within the sample. The mechanical energy was determined from the velocity of the hammers (calculated from the height through which the hammers traveled) and was essentially constant for each deformation cycle. The heat was determined from the temperature increase of the sample which was measured by an embedded thermocouple. Specific heat data were calculated from Neumann&apos;s rule using tabulated data for pure metals.9 Since the fraction of the energy which is stored is large compared to that for pure metals, specific heat data of high accuracy are not required. Successive increments of deformation were carried out by repeating the procedure, the limit being determined mostly by the decreasing accuracy caused by the increasing corrections and the decreasing storage of energy. About five cycles were used to give a true strain of about 0.5 while the time interval between cycles was 1 to 2hr.

Jan 1, 1963

By E. C. Harder

INTRODUCTION THE situation in the United States, at the present time, regarding the supply of manganese ores and alloys of manganese is one of great seriousness and is likely to become increasingly so while the European war continues. The two principal iron-manganese alloys, ferromanganese and spiegeleisen, are indispensable in steel manufacture, being used extensively in the Bessemer and openhearth processes.. Spiegeleisen, the lower alloy, contains between 15 and 25 per cent., and ferromanganese, the higher alloy, between 60 and 80 per cent., of manganese. Besides manganese the alloys contain iron and carbon. On the market ferromanganese is usually quoted on the basis of 80 per cent. manganese, and spiegeleisen on the basis of 20 per cent. manganese. The consumption of ferromanganese has been increasing during recent years at the expense of spiegeleisen, because larger quantities of the latter must be used to ac-complish the same purpose with the result that the amount of carbon introduced with it into the molten metal is frequently injuriously great. Manganese ore proper, in the form of manganese dioxide, is used extensively in many chemical industries, especially for oxidizing purposes. It is also used for the manufacture of both wet and dry electric cells and in the manufacture of paints and dyes. The manganese ore used in this country has been derived hitherto from three principal sources:. Southern Russia, Southern British India and East Central Brazil. The following tables show the quantity of manganese ore imported from these countries, and (for comparison) the domestic production, during 1912, 1913 and 1914. The imported manganese ore has been used largely in the manufacture of iron-manganese alloys and in addition large quantities of the alloys themselves have been imported, chiefly. from Great Britain, Germany and other European countries.

Jan 5, 1916

From the historical account of the coal industry set forth in the preceding pages the reader will have learned that coal is extremely widely spread throughout the United States, and in most places it has been easily found, that it has been remarkably easy to develop, and, where the deposits were available to streams on which it could be transported to markets, it was opened almost as soon as the country was settled. Such were the mines along the James, Susquehanna, Monongahela, Ohio, Kentucky, Cumberland and Big Muddy Rivers. In other localities where such easy means of transport were not convenient, the early production was confined to local use, or to places to which it could be hauled by wagons, but everywhere small mines were established almost as soon as the country was settled, and these increased both in number and size as the available markets grew. These early mines were nearly always opened by local people, and the industry was so far-flung that its growth attracted little or no attention excepting when a labor disturbance or a breakdown in transportation occurred. Had it been concentrated in a few places as most metal industries were, or as the petroleum industry was for many years after it started, it is probable that much better records of its progress would have been kept. When the canal era began, in the eighteen twenties, coal was at first not considered as a valuable source of freight revenue, and much surprise was expressed that the receipts of the Schuylkill Canal were very largely from coal after the first few years, as was the case of the Union Canal though not to such an extent. Even the early railroads to the coal fields did not realize the extent to which the products of mines would figure in their revenues, and it was many years before railroads were built practically solely for prospective coal traffic; indeed this did not happen until some years after the Civil War. Map 12 shows the extent of the canal system in the United States in its relation to the coal fields at the time of its maximum development. It will be seen that only the coal areas in Pennsylvania, Ohio, and to a very small extent in Indiana were able to ship by canal at all, and that only a very small portion of such fields could do so. Looking backward, it is hard to understand the great hopes entertained of canals by their pro-

Jan 1, 1942

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.&apos; Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.&apos; Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10&apos; psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948