Search Documents

By William Marsh Baldwin

THE ROLLING OPERATION proper is applied to metals and alloys not only in the production of flat products but also in the production of shapes, rods, wire and even in specialized forms in the production of tubes. The present discussion of rolling copper and copper alloys will be [ ] limited to a consideration of rolling flat products such as strip, sheet, foil, plate, and others. In this case (as in the others listed above), the rolling operation itself is only part of an integrated sequence of operations. In Fig I such a sequence going to make up a brass strip mill is sketched out. It is seen that the rolling opera-

Jan 1, 1948

Jan 1, 1969

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952

[NORTH AMERICA ALASKA Anchorage.-Strandberg, H. Chlchagoff.-Russell, J. C. College.-Barber. R. J. Dorsh, J. B. Fox, E. F. Joesting, H. R. McAnerney, J., M. Douglas.-Cahill, W. E. Fairbanks.-Beistline, E. H. Crawford, J. D. Earling, R. B. Greves, J. H. Harris, Q. P., Jr. Henton, H. M. Herbert, C. F. Hester. W. B. Hopkins, J. E. Kreitlow, E. J. MacDonald, D., III March, J. P. Mathews, T. C.]

Jan 1, 1940

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike's Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE use of galvanic cells for the determination of oxygen activities has spread rapidly since the suitability of calcia-stabilized zirconia as a solid electrolyte material was first demonstrated by Kiukkola and Wagner.' In many of these investigations:-7 including several at ARL, the free-energy changes for various oxidation-reduction reactions involving the oxides FexO, NiO, and Cu2O have been measured as a means of assuring that a cell apparatus is functioning properly. As a result, a large quantity of data pertinent to the calculation of the high-temperature standard free energy of formation (?GO) of these oxides has been accumulated. AGFexo has been carefully measured in many independent investigations, using a variety of techniques, and consequently is accurately known. chipmans has used this informa-

Jan 1, 1968

By W. H. McFarland

The mechanical properties have been determined for a large number of alloy-free martensitic steels with carbon contents ranging from 0.08 to 0.20 pct and with manganese contents of about 0.4 to 0.5 pet. These steels were tested 1) as water-quenched, 2) after quenching, temper rolling, and tinning, and 3) after tempering treatments which involved temperatures from 400o to 1300oF and times from 1 min to 8 hr. The majority of these tests represent steel from commercial-size coils, i.e., strip 32 in. wide, coil weights up to 20,000 16, and steel thicknesses from 0.0055 to 0.024 in. As a result of these treatments, it has been shown that as-quenched low-carbon alloy-free steels can be produced with tensile strengths ranging from 140,000 to 220,000 psi and tensile elongations from 3.0 to 4.0 pet in 2 in. The tensile strength of the as-quenched martensites can be represented by the equation, tensile strength (ksi) = 119 + 560 (wt pet C). The response to tempering of these steels is related to previous work by Muir, Averbach, and Cohen and by Grange and Baughman. Strain aging of low-carbon martensite has also been investigated. If low-carbon steels are defined as those steels with a maximum carbon content of 0.2 pet, it is found that the literature on low-carbon, alloy-free martensites contains little data on the mechanical properties of these steels. However, the following facts concerning low-carbon alloy-free martensites seem firmly established:'-' 1) The major factors in controlling the strength of the martensite appear to be a) fine structure, b) the internal strain resulting from the transformation, and, particularly, c) the amount of carbon in solid solution. 2) In low-carbon steels, the martensite is auto-tempered and is in the form of needles with only minor amounts of internal twinning, whereas the martensite in high-carbon steels forms as plates which are internally twinned on a fine scale. 3) Care must be taken in comparing the results of work that has been done on low-carbon steels with varying amounts of alloying elements to data on plain carbon steels. As has been noted by Irvine, Pickering, and Garstone,6 alloying elements generally lower the martensite start temperature and, thereby, decrease the amount of auto tempering obtained during the quench. This makes it difficult to

Jan 1, 1965

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

Philip Argall, Denver Col. (communication to the Secretary): Dr. Raymond claims (Trans., xxiii., 560)) that my statement (p. 557) regarding the crystallization of iron "is beyond question incorrect." He says: "It is not even settled that vibration will crystallize iron under any conditions." While admitting that authorities differ on the possibility of cold crystallization of iron, I believe it is a settled and undisputed fact that vibration in the presence of heat will crystallize iron. Bloxam and Huntington say :* " Vibration assists 'in converting fibrous metal (iron) back into a crystalline state when heated, a lower temperature sufficing than in the absence of vibration." Mr. A. F. Hill, summing up a very exhaustive review upon the crystallization of iron and steel, pronounces against crystallization, but only at temperatures below 900' F. Mr. Howe, discussing ,the breakage of a 20-foot porter-bar with a crystalline fracture, suggests that it was attributable to heat, jointly with the jar. We see, then, that vibration of heated iron bars will induce crystallization and consequent change of structure. Referring to my statement, I wish to point out, that I was discussing the vibration of stamps arid should have said, "vibration under all such conditions," etc. That is, vibration attended with sharp blows, such as a stamp-stem is subjected to, will crystallize iron; yet I believe that intense vibration under any condition will

Jan 1, 1895

By Thomas Wilson

IN a single-crystal cube of iron the arrangement of the atoms is that characteristic of iron at room temperature: the body-centered cubic lattice. X-ray investigation has shown this structure to be characteristic of iron, as it has shown the atomic arrangement of other metals to be characteristic of those metals also. Rarely do substances have more than one characteristic atomic arrangement. Many physical properties of metals are directly connected with their atomic arrangements, so that changes of arrangements produce changes of properties. Only chemical change influences atomic arrangement. If a difference in the physical properties of a metal is caused by a process which involves no chemical change, the cause of the difference in properties must be sought elsewhere than in the atomic arrangement. Frequently this cause can be traced to alteration of crystal orientation. The orientation of a crystal may be defined as the relationship which the crystallographic axes bear to some quantity of reference. A cube of iron appears cubic whether it is regarded from a face, an edge, or a corner. Yet these three positions represent three different orientations of the cube with respect to the observer. It is evident that the orientation of this cube of iron, unlike the atomic arrangement, is not characteristic of iron but is entirely dependent on the previous history of the cube. Most of the processes of metal working, such as wire-drawing, rolling, and bending, change the orientation of the crystals present in the worked metals. These processes usually tend to produce rotation of the crystals into positions approaching a mean. Specimens of metals show-ing this characteristic are said to possess a preferred, orientation. Tensile strength, ductility, and many other properties are influenced by orientation changes; therefore two specimens of the same metal may show different values of these quantities. In metal specimens possessing a narrowly limited preferred orientation, these quantities will vary in magnitude in different directions throughout the specimens. The investigation of the influence of manufacturing operations upon crystal orientation, and hence upon physical properties of metals, is an important

Jan 1, 1929

By Claude H. P. Lupis, John F. Elliott

WAGNERL described the thermodynamic behavior of a metallic solution consisting of the solute components 2, 3,... at very dilute concentrations in the solvent, 1, in terms of the excess partial molar free energy, or alternatively the logarithm of the activity coefficient. In the Taylor expansion of FiE, by neglecting the second- and higher-order differential terms, he obtained the excess partial molar free energy as a linear function of the composition:

Jan 1, 1965

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By J. V. Emmons

It has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass.

Jan 1, 1915

By F. W. SUTTER

IN order to have ore available on the completion of the beneficiation plant at Clifton and to provide for continuous production while underground development was carried out, it was decided to develop an open-pit through the crest of a long hill in which the ore outcropped, using 40-ft. vertical benches.

Jan 1, 1943

By J. W. Ristori, V. R. Garfias

ONE of the most serious problems now confronting Gel- many-and one that will affect Italy even more seriously if she goes to war against England and France -is that of supplying her navy, mechanized army, and air force as well as her industrial and other needs with the necessary and related products. This problem, serious even now, will become vital should hostilities on a large scale develop.

Jan 1, 1939

By R. F. Mehl

Jan 1, 1936

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

CONTENTS KANSAS-H. S. BRYANT 3 TEXAS, EXCEPT GULF COAST-M. C. CHENEY 14 GULF COAST-L. P. TEAS 21 TEXAS PANHANDLE-W. E. HUBBARD 29 LOUISIANA, ARKANSAS AND MISSISSIPPI L H. K. SHEARER 37 ROCKY MOUNTAINS-R. C. COFFIN 43 CALIFORNIA-V. H. WILHELM 51 MICHIGAN AND THE TRENTON FIELDS OF OHIO AND INDIANA-M. G. GULLEY 65 ILLINOIS, WESTERN KENTUCKY AND WESTERN INDIANA-A. H. BELL . . . 73

Jan 1, 1932

By S. E. Bronisz, R. E. Tate

s-plutonium samples possessing a strong growth texture have been produced by allowing them to transform under pressure from p to a. A fiber texture with [010] parallel to the pressure axis results. The textured samples are expected to be useful in determining the effects of crystallographic orientation on the physical properties of a plutonium, and initial results of measurements of resistivity and mechanical properties are described. THE crystal structure of a plutonium1 is mono-clinic, P21/m, and many of the metal's properties should reflect the crystallographic anisotropy. Unfortunately, it has not yet been possible to grow useful sizes of single crystals of a plutonium. Therefore, few of plutonium's orientation-sensitive properties have been determined as a function of crystallographic orientation. One way to gain information about at least some of the orientation-dependent properties is to study a highly textured sample. Such samples have been produced by cold rolling a plutonium,2 but they are necessarily very small in one dimension. We have now successfully used two other techniques to produce highly textured samples, not limited to small thicknesses. METHODS OF PRODUCING PREFERRED ORIENTATION The texture is produced by causing the plutonium to transform from ß to a while under pressure. It was observed by Gardner3 that applying a compres-sive load during the transformation resulted in the formation of columnar grains of a plutonium, and Cramer4 observed a similar structure in some diffusion couples rolled in the P phase. Neither of these workers, however, investigated the subject beyond these observations. The more flexible of the two methods developed is that of compressive loading. The technique is to enclose a sample of plutonium in a die assembly before applying the load. It is possible, of course, to dispense with the die and simply press the sample between two platens. In this case, however, the unrestrained sample deforms during the pressing, making it difficult to maintain the load and to control the final sample thickness. This compressive loading technique has been used on specimens ranging from 1/4 to 3 in. diameter, with height-to-diameter ratios ranging from 5 : l to 1:6. The procedure begins with loading the sample, a right cylinder of a plutonium, into the pressing die. Plastic deformation of the sample while it is being pressed is minimized by machining the sample so that its diameter is nearly the same as that of the die barrel. Then the loaded die assembly is placed in a vacuum pressing can that fits on a hydraulic press. After a vacuum is achieved the die assembly is heated to 180°C and equilibrated. The load is then applied and the specimen and die are allowed to cool to about 40° to 50°C before the pressure is removed. The resulting sample is composed of rod-shaped a -plutonium grains, the rod axes being parallel to the cylinder axis and the pressing direction. Photomicrographs of the oriented structure are shown in Fig. 1. Although most of the specimen is composed of grains whose rod axes are parallel to the cylinder axis, a thin, peripheral layer consists of rod-shaped grains whose rod axes are perpendicular to the cylinder axis. Presumably, the highly plastic nature of p plutonium leads to approximately hydrostatic conditions during the initial stages of the P — a transformation under pressure. At this time, the grains in the peripheral layer would have grown parallel to the local force direction. During the latter stages of the transformation, the accompanying volume contraction would have eliminated the radial forces, leaving only the axial force and resulting in the growth of the observed structure. The growth texture did not form without the application of pressure. Attempts were made to produce the texture by repeating the standard temperature cycle without

Jan 1, 1965

By H. Ries

Introduction BODIES of pyritic ore in schistose rocks have long been known in different parts of the world. The several occurrences resemble each other in being usually of more or less lenticular shape, inclosed in walls of schist or gneiss, and carrying pyrite, chalcopyrite, and pyrrhotite in varying proportions, as the chief ore minerals. The deposits differ, however, in that sometimes one, sometimes another, of the three sulphides mentioned may predominate. The orebodies in general are more or less closely conformable with the schistosity of the wall rocks, although in cases this may not hold true. The boundaries may or may not be sharp, but in general are fairly distinct. The lenses vary in size, may occur singly, or in groups; in the latter case they may be in line, overlapping, or occasionally parallel. Pinching and swelling of individual lenses is not uncommon. The genesis of these pyritic bodies has provoked much discussion, and they have been variously classed as sedimentary, igneous intrusions, hydrothermal replacements or impregnations, etc. Indeed, in some cases different geologists have most positively assigned widely diverse origins to the same deposit, as in the case of Rio Tinto 1 and Rammelsberg.2 It is true that in the light of modern criteria, we have been able in a few cases to decipher clearly the process of origin and so there seems no doubt now regarding the genesis of the deposits at Rio Tinto, Spain;3 Rammelsberg, Germany ;4 Ducktown, Tenn.;5 southwestern Virginia;6

Jan 8, 1917