Search Documents

By Walter Nummela

INTRODUCTION By the end of 1979 pellet productive capacity from the processing of low grade iron ores in the Lake Superior-District will total 86 million tons per year. Of that tonnage, 72 million result from the processing of magnetic ores such as taconite, about 6 million tons from the flotation processing of relatively coarse grained specular hematite, and 8 million tons from the processing of fine grained non- magnetic ores at Tilden. The Tilden flowsheet represents a break- through in the processing of this type of crude ore and hence is unique in the Lake Superior District (1). Operations at Tilden started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleve- land-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling- Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Other companies have conducted extensive pilot plant tests or are in commercial production in the processing of fine grained non-magnetic ore materials (2). Flowsheets and reagent schedules may be different for each particular application, but some of the problem areas in the processing of Tilden ores have also been experienced at operations such as the IOC Plant at Sept-Isles, at Lamco and at Bong in Liberia, and in pilot testing of Fabrica ores of Ferteco Mineracao in Brazil. With a grind of about 80-85% -500 mesh resulting in 50% of the particles in the concentrate being less than 15 microns, a discussion of the pro- cessing of Tilden type ores fits the topic of this workshop. There are very large tonnages of fine grained non-magnetic crude ores which exist throughout the Lake Superior District and other iron ore producing regions. These fine grained non-magnetic materials constitute an important source of iron minerals. Before going into specifics of the flowsheet, it is important to

Jan 1, 1979

By M. E. Wadsworth, L. H. Raby, A. S. Peck

Infrared spec troscopy was used to study the adsorption of oleate collector on three varieties of hematite. Each of the minerals was found to react with either oleic acid or a solution of sodium oleate to form a mineral cation-collector anion chemisorbed layer at the solid-liquid interface. The chemisorption reaction displaced surface hydroxyls and was found to be pH dependent. The infrared band characteristic of the antisymmetrical C = 0 structural group of chemisorbed oleate appears between 1520 and 1540 cm-'. Evidence is presented which shows that molecular filming of the mineral surfaces with un-dissociated oleic acid precedes chemisorption. Infrared absorbance is correlated with the flotation behavior of the mineral. Adsorption processes are usually classified into two types which are distinguished and character- ized by the nature of the bond formed between the adsorbate and adsorbent. The process in which molecules chemically bond to solid surfaces is termed activated adsorption or chemisorption. If only weak van der Waals forces bind the molecules to the surface then the process is termed physical adsorption. Chemisorption is of primary interest in flotation systems since selectivity may be obtained if a single mineral is rendered air-avid by a specific collector mineral adsorption reaction. In previous studies infrared spectroscopy was used to define the mechanisms involved in the adsorption of oleic acid and sodium oleate on fluorite, barite, and calcite. Infrared techniques were particularly useful since adsorbed monolayers were identified in situ. Further, the infrared method permitted identification of reaction products in the solid, liquid, and vapor phases of the systems. The chemisorption reactions displaced F- from fluorite, SO4 from barite, and CO3 from calcite. This investigation was pursued in an effort to characterize and interpret the adsorption processes for synthetic hematite, compact red hematite, and specular hematite (crystalline hematite). Adsorption tests were performed using either oleic acid or

Jan 1, 1967

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps : 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. .These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the molecules will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1964

By A. B. Cox, L. W. Wark

An attempt has been made to compare the influences of the two most widely used depressants—alkalis and sodium cyanide—and the most widely used activator—copper sulfate—on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in lhis group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,' was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating. results, the other four collectors were tested, in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed. In general, then, of the three types of collectors investigated, the dithiophosphate type is most easily influenced by depressants, and the

Jan 1, 1935

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920

By E. J. Ripling

TUBES may be produced by a large number of forming processes, the most common of which will be discussed analytically in this paper. In no case will the stress analysis for any given tube producing process be derived formally for where such analyses are available, they may be referred to readily. Rather, emphasis will be placed on the interpretation of the theory of the different processes, few of which are developed to a state that will allow rigorous mathematical analyses, in an attempt to give a rational description of the effects of the different variables involved in each method. Tube producing methods can be divided into two groups: Those used to form shells, and those used to further work these shells into a shape more suitable for their final use. Among the first group are included roll piercing, extrusion and cupping for seamless shells, and bending with welding for welded tubes. The re-forming processes include sinking, drawing with a plug, and drawing with a rod. Only the plastic forming operations will be discussed here; other forming processes such as casting shells will not be considered. PRODUCTION OF SHELLS Shells for Seamless Tubing Piercing: The extremely important process of forming an axial hole in a billet by oblique rolling never has been analyzed satisfactorily, although a certain amount of experimental work relating to this process has been conducted. There are a number of factors that make piercing difficult to analyze; one of these is the fact that piercing is not a problem in plasticity, but one in fracturing, and the laws of fracturing are even less well understood than those of plasticity. If, however, it is assumed that fracturing occurs on a surface as a result of tensile stresses acting normal to this surface, piercing can be analyzed qualitatively by examining the stresses established in the oblique rolling process. To determine the origin of the tensile stresses that are thought to effect piercing, it will be necessary to know the angular relationships between the maximum stresses that are established in piercing. These angles quite frequently can be determined in a plastic deformation process by an examination of the deformed product. For example, consider the stresses established when a tensile test is conducted on a rectangular cross-sectional specimen of pearlitic steel. When stretched, this material first flows plastically, exhibiting the well-known yield jog on a stress-strain curve. The formation of the slip areas that give rise to the yield jog can be detected during the straining, since these flowed areas cause depressions on the specimen surfaces which can be seen if the surfaces are polished highly. The plastically strained areas also can be found after the specimen has been stretched to a strain not exceeding the yield jog, by sectioning the test piece and. etching these sections with Fry's etch. With this etchant, it is possible to dis-

Jan 1, 1951

By B. M. Larsen, W. E. Shenk

This paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable —that is, the time interval between successive reversals—should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one lLminimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: I. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potenti-ometric control instrument, to correct any tendency toward temperature unbalance between ends of the furnace. 3. A second "maximum temperature

Jan 1, 1945

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By Eugene N. Cameron

Graphite is the hexagonal form of crystal-line carbon. It is found in nature locally as tabular crystals but occurs mostly as disseminated flakes, foliated, platy, or fibrous masses, or microcrystalline compact to earthy material. Graphite is characterized by its gray to black color, metallic luster, black streak, perfect basal cleavage, softness (H = 1-2) and unctuous feel. It is sectile and flexible and has a specific gravity of 2.1 to 2.3. It is an excellent conductor of heat and electricity and is inert to ordinary chemical reagents. It melts at a temperature of about 3500°C and vaporizes at a temperature of about 4500°C. In the presence of oxygen it oxidizes to CO2 in the temperature range 600° to 700°C, but it is stable at ordinary temperature and markedly resistant to chemical weathering. Although some natural graphite is nearly 100 pct pure carbon, most contains mechanical impurities of various kinds; quartz, biotite, muscovite, pyrite, iron oxides, and feldspars are the most common. Commercial graphite products have a wide range of graphite content, but the better grades contain 80 pct graphite or more. Both natural and manufactured (artificial) graphite are used in industry. Natural graphite products are divided into two broad categories based on grain size. Graphite composed of visible crystals is called "crystalline" graphite, whereas graphite so fine-grained that it is not visibly crystalline is termed "amorphous." The distinction is arbitrary, for all natural graphite is crystalline, and all gradations between the two commercial categories are known. Within the two categories the terminology used in industry is confusing and not entirely consistent. Crystalline graphite comes from two principal types of sources. The first consists of rocks containing disseminated flakes of graphite. This source yields the "flake graphite" of industry. The second comprises vein deposits of graphite, of which those in Ceylon are the most important and furnish the Ceylon graphite of industry. Amorphous graphite comes from any of a variety of sources, including some of those that yield crystalline graphite. Manufactured graphite is made by electric furnace processes, mostly from petroleum coke. Occurrence and Distribution of Graphite Deposits GENERAL Graphite is widely distributed in nature, occurring in igneous, sedimentary, and metamorphic rocks, and even in nickel-iron meteorites. Graphite deposits of economic interest, however, occur mostly in metamorphic terranes. Five principal geologic types of deposits are recognized: 1. Deposits consisting of flake graphite disseminated in metamorphosed siliceous sediments. 2. Deposits consisting of flake graphite disseminated in marbles. 3. Deposits formed by thermal or dynamothermal metamorphism of coal or other highly carbonaceous sediments. 4. Vein deposits of the Ceylon type. 5. Contact metasomatic or hydrothermal deposits in marble. DEPOSITS IN METAMORPHOSED SILICEOUS SEDIMENTS Deposits consisting of flake graphite disseminated in metamorphosed siliceous sedi-

Jan 1, 1960

By Gust Bitsianes, Joseph H. M. Beaty

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By E. V. Crane

A tremendous volume of the metal rolled annually into sheets strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features In common with rolling and wire-drawing methods. Combinations of stresses are diffcrent, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group. Shearing Operations The shearing group of operations, including blanking, piercing, trimming, shaving, slitting, shearing, notching, parting and numerous variations and combinations of these enters once or more into the production schedule of practically every stamped or forged article. The transverse stress, set up in shearing, as shown in Fig. 1A, is a combination of an angular compressive thrust and a tensile stress which is also at an

Jan 1, 1931

By Leendert de Witte, Fred J. Radd

In many areas caring failures can be directly related to electrical currents observed in the casings. It is the thesis of this paper that the observed casing currents are mainly due to electrochemical potentials of the type in evidence on spontaneous potential curves of electrical logs. The general nature of these potentials are discussed and an equivalent circuit is given for current and potential distributions around open holes. The casing forms a short circuit to these potentials and tends to average the effects of local cells. The case of casing corrosion opposite the Dakota water sands in the salt-mud area of Kansas is discussed anil used us a qualitative, illustration of the relation between SP's and casing currents. A method of quantitative derivation of casing current distribution frorn electric log SP curves, using linear transform theory, is described and results are compared with a measured current profile. The effects of hydrogen over-potentials at the cathodic portions of the pipe are considered and some laboratory data are given in support of conclusions regarding the over-1.01tuge.s. INTRODUCTION To date an appreciable amount of work has been done on the measurement of oil well casing currents and on the correlation of the anodic portions of the current profiles with corrosive casing failures. Speculations on the origin of the casing currents have, however, remained rather vague; and although almost every plausible cause has been mentioned, there is to the writers' knowledge no clear-cut expose' on the details of the causes of the corrosive currents in the literature. A study of current surveys and casing failures in the N.W. Burnett field, Ellis County. Kan.. indicated the probability that concentration cell emf's between the Wellington salt section and the relatively fresh waters in the Dakota sands were a major cause of the corrosion currents. A more general concept evolved upon analysis of the severe corrosive conditions in the Pleistocene sands in the Ventura Avenue and San Miguelito fields in California. In this area no major variations in the salt content of the formation waters occur and yet large casing currents are observed. An explanation is found in the fact that the local spontaneous potentials which are set up due to concentration contrast between the drilling fluid and the connate water are short circuited when casing is set. The very conductive path through the casing increases the magnitude of the currents and has the tendency to average local sources over fairly large intervals. Current will flow between the sections that are predominently shaly and the sections that are mostly sandy. At the places where the current leaves the pipe, corrosive attack will occur. This same phenomenon will be present wherever unprotected pipe is set through sections that show large SP kicks on the electric logs over reasonably thick interval~. GENERAL- NATURE OF THE SPONTANEOUS POTENTIALS When a sequence of sedimentary rocks is penetrated by a drill hole filled with a mud which has a different salt concentration from that in the formation waters, various types of electrochemical potentials are established between the formations and different parts of the mud column. Opposite clean sand sections. a simple liquid-liquid junction potential will be observed; while opposite argillaccous formations, a membrane potential, often referred to as shale potential, will be established. The first quantitative analysis of these emf's in terms of liquid junction and membrane potentials is due to Wyllie.1

Jan 1, 1956

By R. Ebeling, M. F. Ashby

The paper is in two parts. The first develops the formulae and method needed to calculate the size, nu)nber, spacing, and volume fraction of hard or inert particles in the interior of a specimen from measurernents made on an extraction replica; throughout, the spread of- particle sizes in a single specimen is taken into account, and the extraction efficiency of the replica is considered. A method for testing whether the particles are randotnly distributed in space is described, and the spacing of randomly distributed particles is discussed. The second Part describes the application of the method to copper containing spherical particles of silica; the description includes an estimate of the errors involved, and a comparison of this with alternative methods. All parameters except uolume fraction can be determined satisfactorily, and the method offers advantages over other electron-,rzicroscopic techniques when dealing with hard particles in a softer matrix, or inert particles in a chem-ically less inert matrix. 1 HE experimental measurement of sizes and numbers of discrete particles of a second phase embedded in a matrix material from opaque, plane sections has been considered by many authors, notably by Fullman.' It is assumed that, when the specimen is sectioned, the particles are also sectioned, so that the diameters of the circles of intersection of particles with the plane of the cross section ("surface diameters") are measured. It is difficult to derive the distribution of true particle diameters ("volume diameters") from measurements of the distribution of "surface diameters" on a plane section. The measurement of size and numbers of small second-phase particles by transmission electron microscopy through thin foils of matrix containing the particles has been described by Cahn and ~uttin~' and by ~illiard.~ Because of overlap and the fact that particles which intersect the foil surface may be sectioned whereas those in the bulk of the foil are not, it is again difficult to measure the true distribution of particle sizes. The use of replicas for this sort of measurement has not been analyzed in detail. A replica made from an opaque cross section, thus replicating the circles of intersection of particles with the plane of section, is analyzed by Fullman's method and suffers from the same difficulties. Under certain circumstances, however, extraction replicas can be used, and offer a special advantage in that they make the determination of the true distribution of particle diameters particularly simple. It is the purpose of this paper to describe this extraction replica method. Consider the example of an alloy consisting of SiOz particles, whose mean diameter is about 1000A, dispersed in a copper matrix. When the alloy is sectioned and mechanically polished, the particles are not sectioned, because they are much harder than the matrix, and so will be either left in the surface or pulled out whole, and because the particle size is smaller than the abrasive size of even the finest abrasive. The particles are chemically inert in solutions which chemically etch or electropolish the matrix, so that chemical treatments do not section the particles either. (Experimental measurements of particle shape in this alloy confirm this—truncated particles are never seen.) Small, hard or inert, particles are therefore not sectioned when the specimen is sectioned and polished. An extraction replica taken from this polished surface shows the true "volume" diameter of each extracted particle; the distribution of diameters seen on the replica is the surface distribution of true "volume" diameters, and the volume distribution of true "volume" diameters is easily derived from it. The extraction replica method is not subject to the difficulties associated with sectioning of particles, and avoids the problem of overlap from which the transmission method suffers. The method is well-suited for studying hard particles in a soft matrix. Examples are provided by internally oxidized alloys, oxide-dispersion strengthened metals like T.D. Nickel, and carbides, nitrides, and strong intermetallic compounds in metals. It should be possible to adapt polishing techniques in alloys containing softer but inert particles to avoid sectioning the particles (say by electropolishing or etching). The method is tested and illustrated in Sections 8 and 9 by applying it to a dispersion of spherical SiO2 particles in a copper matrix. I) SYMBOLS Symbols are defined where they first appear in the text. Volume fractions of particles are denoted by the symbol f, particle diameters by x, center-to-center particle spacings by D, and numbers of particles by N. Mean particle diameters and standard deviations about these means are denoted by x and a. Both arithmetic (subscript A) and geometric (subscript G) means are employed. In this paper we measure the distribution of true diameters of particles which touch or pass through a random-plane section of the specimen. We may want to know the distribution of particle diameters in the

Jan 1, 1967

By R. W. Raymond

The absence of a convenient glossary- of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copy, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By E. V. d’Invilliers

The position of these magnetic ore-mines, with reference to the county-seat, is shown in Fig. 1. They are situated on the south margin of the Great Valley, five miles south of Lebanon, and about midway between Reading on the Schuylkill River and Harrisburg on the Susquehanna River, in three prominent, contiguous hills, standing in front of the Mesozoic red shale arid sandstone hill country of northern Lancaster and southern Lebanon counties, and overlooking the great limestone plain to the north. The three hills, named respectively Big, Middle, and Grassy Hills, and separated from each other by two branches of Furnace Creek, range in a nearly east and west direction for a distance of about one mile. Their summits are respectively 870, 715, and 700 feet above tide. The railroad line opposite the base of Middle Hill is 575 feet above tide at Cornwall and 471 feet at Lebauon. These features are all distinctly illustrated in the contour-line map accompanying this paper, but are made still more clear in the relief. map, Fig. 2, comprising, as it does, about six square miles of territory contiguous to the ore-mines. This is a photographic plate of a model made by Mr. A. E. Lehman, from surveys of my own and Mr. W. F. Shunk. The model was built in layers of cardboard, each layer representing one 10-foot contour-carve line. The scale was the same as the original map, 400 feet= 1 inch, without any vertical exaggeration. The lowest contour-line is 530 feet above ocean level; the highest, 1075 feet. The center of the model was made the focusing-point of the view, which was taken—according to scale—51/2 miles north from and 24 miles above the focusing-point, looking southward. When first mined in the last century these hills exhibited smoothlyrounded surfaces, composed of soft weathered ore of great parity, beneath which lay the great mass of hard ore, constituting the whole

Jan 1, 1886

By E. M. Wise

THOUGH known as the platinum-group metal- the sextuplet, platinum, palladium, iridium. rhodium, osmium, ruthenium, might well be called the American metals or perhaps Pan-American metals, as the ore containing them eras first discovered in South America, and in recent years the largest production has come from North America. The South American alluvial deposits, which also, contain gold, are in active production, as are the alluvial platinum deposits of Alaska, but the main production is from the copper-nickel ores of Sudbury, Ontario. The Russian deposits in the Urals were the source of most of the worlds platinum for about 100 years, but since 1934 have assumed second place. For a time considerable amounts of platinum came from several rather rich deposits in South Africa but these were exhausted quickly. However, a tremendous reserve of lower-grade ore exists there, which could be worked profitably if the price of platinum were considerably higher.

Jan 1, 1942

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952

By W. P. Sykes

THIS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Molybdenum (m.p. 2500° C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450° C. and an allotropic change at about 370° C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per cent. iron. Aluminum is one of the low melting-point metals. Some tensile tests at elevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available recommended this metal. The samples marked Al are an aluminum-copper alloy; they contained 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat complicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400° C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate

Jan 1, 1921