Search Documents

By Heinrich Oscar Hofman

IN THE death of Professor Hofman who was born on Aug. 13, 1852 and died on April 28, 1924, the world has lost a great metallurgist and a great author of metallurgical literature. Measured in time his life was not quite seventy-two years, but measured in work accomplished it was much longer than this. It is not surprising that Dr. Hofman became a great scholar for his father, Karl Hofman, was on the faculty of Heidelberg University, and his early days were spent in these surroundings. He studied in the University under such men as Kirchoff and Bunsen and often spoke of the intimate relations he had with them. Following his course at Heidelberg, he studied at the Clausthal Mining Academy where he graduated with honors, receiving the degrees of Mining Engineer and Metallurgical Engineer in 1877.

Jan 1, 1924

By Donald L. Katz

THE Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July 1, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produces 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand' indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplification and generalizations are necessary to give the over-all picture in so short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, r, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City. Wilcox Secondary Recovery Association on Sept. 5;.1940. Some information is taken from a report to the Association by C. V. Sidwell on March 1, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." HISTORY OF WILCOX ZONE The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. 12.1 .4 and areal map of Fig. 2. The sand is of Ordivician age and is composed of well assorted, rounded' sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 was dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1937 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1941

Shovel To further increase the efficiency in the production of their foundry sand, the American Silica Sand Co. has purchased a new and improved shovel that will be used for loading trucks at their Reynolds Pit. The [ ] new shovel will greatly facilitate winter mining operations and make possible larger winter shipments of the company's foundry sand. The Reynolds Pit is one of three sand pits in the Ottawa district owned by American Silica which produce sand that is refined for foundry use. Circle No. 1 Electric Switches The Crane Electric Co. has just announced the production of their R-1000, a new rotating limit switch designed to control the travel of any rotating device requiring interruption or establishment of electrical current after a predetermined number of revolutions. It is useful for machinery, lifts, and other power equipment. The switch is presented in a finished case, 16 gage, reinforced, with walls of sufficient strength to hold the entire mechanism and all the parts in accurate alignment. The worm gear combination has a 60 to 1 ratio, sufficient for most industrial uses. The number of revolutions can still be increased by using various combinations of driving sprockets, either on the shaft of the switch, or on the sprocket of the unit controlled by the switch itself. Circle No. 2

Jan 1, 1952

By G. S. Hume

RECENT developments in the Turner Valley gas and oil field, 40 mi. southwest of Calgary, Alberta, have indicated a large producing crude-oil area. Drilling be¬gan in Turner Valley in 1913 but no major developments took place until the fall of 1924, when Royalite No. 4 well at a depth of 3740 ft. in the upper part of the Paleozoic (Mississippian) limestone obtained a production - of 20,000 M cu. ft. of gas with a content of about one imperial gallon of naphtha (73° A.P.I.) per M cu. ft. This well produced as much as 600 bbl. of naphtha per day, and until abandonment in 1934 produced 911,313 bbl., which together with the gas sold was valued at about $5,000.000.

Jan 1, 1937

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff's, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

Bellows Connector Fabricated of chemically inert Teflon, the new bellows type connector has many pipe line applications where vibration, expansion and electrolysis exist in the handling of corrosive liquids or gases and solvents. The new connector is electrically non-conductive, flexible even at 94°F and as strong as 480°F as at 70°F, according to the manufacturer. This bellows connector serves as a [ ] vibration dampener as well as an expansion joint and connects misaligned couplings and insulates flanges electrically. End flanges of the joint are French-type envelope gaskets made integral with the joint for easy assembly between companion flanges and a tight, leak-proof seal on installation. Circle No. 1

Jan 1, 1952

Rougher Cells The photo shows one of three carloads of new Denver Equipment Co. rougher flotation machines destined for a single customer. [ ] Low level froth overflow on both sides, and double impeller mechanisms in an open-flow type tank, were designed to enable control of variable conditions in the rougher circuit for better metallurgy. Intense agitation and aeration are claimed, for effective recovery of low-grade mineral particles. Standard parts are used, interchangeable with regular Denver Sub-A units. The Super Rougher is now in production and a 2-cell No. 24 machine will be displayed at the Mining Show. Circle No. 1 Fans A line of industrial fans built for air or materials handling is available in eleven sizes from 670 to 44,000 cfm capacity from Westinghouse Electric Corp. The air hand¬ling wheel has backwardly-inclined blades. Circle No. 2 Trolleyphones The Femco Trolleyphone, plug-in model, 2550 series, is offered as a simple mine or mill communications system by Farmers Engineering & Mfg. Co. More compact, easier to install and service, the new model is powered from existing trolley wire or power line. Circle No. 3

Jan 1, 1952

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

The effect of such variables as feed size, particle shape, cleavage, and hardness on the relative proportion of impact, abrasion, and chipping events in a tumbling mill is demonstrated. The concept of an average event, which is a combination of the three comminution mechanisms, is introduced. It is postulated that the average event in a particular mill determines not only the size distribution but also the energy-size reduction relationship for the comminution process. Fragmentation of particles in tumbling mills appears to result from a combination of impact, abrasion, and chipping grinding.' The relative rates of size reduction attributable to any of the basic grinding mechanisms must depend upon a number of variables, such as feed size, particle shape, hardness, and the number and kind of particles in the mill. The purpose of this paper is to show experimentally how these variables in the properties of materials affect the size distributions obtained by grinding the material's in a laboratory tumbling mill. The resulting size distributions will be intetpreted in terms of a combination of three comminution mechanisms. METHODS AND MATERIALS In this study, minerals of widely differing properties were ground either separately or as mixtures in laboratory mills using rods or balls for grinding media. The materials used include quartz, Tuolomne, limestone (99.8% CaCO3), barite, corundum, galena, pyrite, glass beads, and crushed glass. The mill used was 8 in. in diam. and 9-1/4 in. long. For the ball milling tests, 17.6 kg of steel balls (36: 7/8 in. balls, 178: 1 in. balls, and 44: 1-1/8 to 1-1/4 in. balls) were used. For the rod milling experiments, 17.6 kg of steel rods 9-1/16 in. long (25: 5/8 in., 10: 3/4 in., and 5: 7/8 in. in diam.) were used. In each test, 1 kg of solids were ground wet at 60% solids at 77 rpm. In all cases except where otherwise specified, the feed to the mill was 4 x 8 mesh material. Size distributions of the ground products were determined by a wet-dry sieving procedure with Tyler series sieves. Size distributions of mixed products containing limestone were determined by dissolving the limestone with acid and sizing the residue. EXPERIMENTAL RESULTS AND DISCUSSION If the size distribution of the product from a tumbling mill depends upon the relative proportion of impact and attrition (abrasion and chipping) events, altering the grinding conditions may change these proportions and consequently alter the size distribution of the product. Data to illustrate this point can be taken from Gaudin's classic 1926 paper.2 In one series of experiments, Gaudin ground quartz of different initial sizes for four hours in a laboratory ball mill with 7/8-in. balls. In Fig. 1, his data are reproduced as the cumulative fraction finer than the stated size for the following initial feed sizes: 13.3 x 9.4 mm, 6.7 x 4.7 mm, 2.6 x 1.6 mm, and 0.83 x 0.59 mm. As the feed size was decreased, a dramatic change in the shape of the size distribution curves took place, even though the amount of minus 100-mesh

Jan 1, 1964

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

Dump Truck Kenworth Motor Truck Corp. is beginning full scale production of its new heavy-duty, end-dump earth mover, model 801, a truck engineered for earth moving under the most adverse operating conditions. Payload capacity of the Kenworth earthmover is 30,000 lb and it is over-tired for safety, flotation and high tire life. The truck's body capacity, struck measure, is 9.9 cu yd, with heaped [ ] load at 11.9 cu yd. The earth-mover has a full anti-friction bearing mounted, power assisted steering gear, simplified controls, minimum turning radius and wide axle track to insure ease of handling, maximum maneuverability and high stability. The offset cab of the Kenworth visibility for the driver, before and after. Circle No. 1 Safety Equipment A compact, safe, and efficient valve assembly approved by the United States Bureau of Mines for use with MSA air line respirators, abrasive masks, and abrasive helmets has been developed by Mine Safety Appliances Co. The new MSA continuous air flow control valve regulates air flow from a compressed air source to an operator using respiratory protective air line equipment. Three parts-a centridge container, a cartridge and the air flow check valve-comprise the entire assembly of the control valve. A position action adjustment knob on the cartridge container regulates the amount of air flowing to the operator. The valve can be detached from the air line instantly by pressing the trigger on the cartridge container near the check valve. As the trigger detaches the hose, the spring loaded ball-type valve, which is attached to the end of the hose, automatically stops the flow of air. Circle No. 2

Jan 1, 1952

A 2-year moratorium on accreditation of curricula bearing new designations has been declared by Engineers' Council for Professional Development at its Executive Committee meeting on July 29, 1952. Reason: a more definitive description of what the contents of a curriculum should include to be appropriately designated as "engineering" is needed. This action was brought on by the Committee of Evaluation of the American Society of Engineering Education which had become perturbed over the extension of the name "engineering" to numerous fringe curricula. The 2-year period will permit time for the Committee on Evaluation to study the question and make a recommendation for further action by ECPD. ECPD action also provided that the following curricula should only be given provisional accreditation for one year upon either inspection or reinspection; such provisional accreditation to be extended annually for not more than two successive years pending the report: Engineering Physics, Engineering Mechanics, Geological Engineering, Geophysical Engineering, and Textile Engineering. There are 22 such curricula now accredited.

Jan 1, 1952

By Carl Lee

OXYGEN-FREE high-conductivity copper (OFHC brand) that is now being commercially offered for the first time represents a notable achievement in electro-metallurgy and is the outcome of endeavors that have extended over a long period. Its manufacture is novel in that electrolytically refined copper is melted in electric furnaces and cast into vertical water-cooled molds. The ingots show the "pipe" characteristic of sound gas-free metal and microscopic examination even at high magnification reveals no cuprous oxide in the copper. Owing to the patent situation, the United States Metals Refining Co., the producers, cannot at this time divulge the details of manufacture, but the operations are under precise control so that the castings are of great uniformity and the copper contains no residual deoxidant. Figs. 1 and 2 show photographs of cross-sections of a wirebar and a billet, both vertically cast.

Jan 1, 1933

New Products Equipment

Jan 12, 1950

New Products Equipment

Jan 6, 1951

New Products Equipment

Jan 5, 1951

New Products Equipment

Jan 7, 1951

New Products Equipment

Jan 10, 1951