Search Documents

By William Fink

THE constitution of the aluminum-cobalt alloys has been the subject of relatively few investigations. Brunck1 analyzed the residue which remained after treating the 17 per cent cobalt alloy with dilute hydrochloric acid. The results of the analyses indicated the existence of a compound Co3Al13. Guillet2 published a liquidus for the aluminum-cobalt system which contained two maxima corresponding to CoAl6 and CoAl2 and two eutectic points at 30 and 74 per cent Co. The most extensive investigation of the system was carried out by Gwyer,3 whose results are summarized in Fig. 1. It will be noted that at the aluminum end there is a suppressed eutectic at 644° C. By extrapolation of the duration of the eutectic arrest to zero, the composition of the compound was placed at Co3Al13. Another thermal arrest was noted at 550° C., which Gwyer attributed to a peritectic reaction. The present investigation of the aluminum end of the aluminum-cobalt system is the eleventh of a series dealing with the constitution of aluminum; rich alloys prepared from electrolytically refined aluminum.4 Preparation of Alloys.-The alloys used in this work were all prepared from electrolytically refined aluminum, the analysis of which is shown in Table 1. In preparing some of the alloys, metallic cobalt (98 to 99 per cent) was used either directly or in the form of an intermediate alloy, the composition of which is given in Table 1. In order to obtain alloys of higher purity, cobalt was introduced into some of the alloys by means of chemically pure cobaltous chloride which was readily reduced by the aluminum. A small electric furnace with nickel-chromium heating elements was used in the preparation of the alloys.

Jan 1, 1932

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By C. C. Furnas, T. L. Joseph

It is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investiga-tion1,2 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper. Importance of Gas-solid Contact One of the authors has pointed out in a previous report? that the operation of the blast-furnace process is entirely dependent on contact between the gas stream and the solid particles in the stock. The gas stream carries the necessary heat as well as the carbon monoxide molecules that do the work of rednction. In the parts of the furnace in which there is little or no contact between the gas stream and the solids there can be little work of reduction. Obviously, the part of the apparatus that is not doing the work for which it is intended is inefficient; the ideal condition is one in which all portions of the stock column are

Jan 1, 1929

By John C. Branner

No precise geographic limits can be given for the zinc- and lead-region of North Arkansas. In general terms it lies N. of the Boston mountains and W. of the St. Louis, Iron Mountain and Southern railway; but the prospecting and the development of the ore-deposits have not gone far enough to outline more than vaguely the areas over which workable deposits are to be expected. The tardiness of the development of the region is due in part to its topography, as a hilly and partly mountainous country, through which there have been no railways until recently. There is no longer any doubt, however, about the existence in that region of large bodies of zinc-ores. I. General Geology. The general geology of the region is, in the main, quite simple, but that of the ore-deposits is less so. The zinc-regions of North Arkansas lie about the southern flanks of the Ozark dome. The rocks are approximately horizontal, but have a gentle southward dip away from the axis of this dome. Figs. 1, 2 and 3 show the broad features of the to-. pography and geologic structure. South of the zinc-region, the sandstones and shales of the lower Coal-Measures form the north-facing escarpment of the Boston mountains. Beneath the Coal-Measure rocks are the limestones and cherts of the Lower Carboniferous; and these rest upon Silurian and Ordovician beds. The uppermost beds (Coal-Measures) have been cut into by erosion along the mountain-slopes so that their edges or outcrops have a meandering or dendritic form. The same thing happens with the Lower Carboniferous beds; but these, haying been more or less protected by the overlying Coal-Measured, have broader bases, and cover a much larger area. In places,

Jan 1, 1902

By Waldemar Lindgren

No one would maintain that all ore deposits or all deposits of useful minerals have been formed by the same processes. Generally they have originated by special processes of concentration but these may be of many different kinds. Some deposits have their origin in chemical or biochemical processes of concentration in rivers, lakes or seas, others, developed on land by, means of chemical reactions of surface waters on various forms of rocks. Certain insoluble substances remained behind; others were dissolved and precipitated in favorable places. This action -proceeded in the realm of the oxidizing surface waters or in the deeper zones to which the waters from the surface could find their way. Examples of the latter kind may be found in the extensive copper and vanadium deposits of some sedimentary beds or in the lead and zinc deposits of certain broad limestone strata. In these instances the evidence for any other mode of origin would seem to be very weak indeed.1 Nor does it seem possible to deny that circulating waters may form deposits of the more common metals along fissures after having dissolved many constituents from paths traversed. Another very large class has been formed by magnetic processes of concentration. The last 40 years have been a period of intense activity in. the investigation and description of a vast number of deposits; all modern methods have been employed and the result is an accumulation of data, difficult or impossible to master. It has been a period similar to that in petrography. The generalizations, the able deductions have lagged behind. Evidently several geologists have become weary of this "infinite detail" and a mistrust of the microscope seems to have. arisen. Although this feeling of being swamped in microscopic detail is a painful experience, nevertheless only through the detail in combination with

Jan 6, 1926

By G. S. Brooks

WITH the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some. of the western zinc companies turned to the coal fields, attracted by their permanency and the 'success of the Matthiessen & Hegeler Co. and the Illinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate' supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gads in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its share to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On, certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by W. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to-do justice to the more progressive. American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc.

Jan 9, 1919

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act and the Landrum-Griffin Act; the Norris-La Guardia Act, the Wage and Hour Law, the Walsh-Healey Act, and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously without regard to the interests of management, the employes, or the public. During 1958 and 1959 revelations of corruption and coercion in labor unions made before the McClellan Committee of the U. S. Senate generated considerable public sentiment in favor of legislation to protect the interests of employes and the public. However, the resulting legislation, the Labor-Management Reporting and Disclosure Act of 1959 (Landrum-Griffin Act), demonstrated quite clearly that the political power of the labor union leaders was adequate to prevent adoption of effective measures in this field.

Jan 1, 1964

By Edward Chapman

IN the Leadville district toward the close of the "intermediate mesothermal period" of mineralization, there occurred a stage of ore deposition marked by a rather complex mineral association. As bismuth minerals formed in many places during this period, it is here called the "bismuth stage" for convenience of description. The minerals so far identified with this stage, listed roughly in the order of prominence, are: chalco-pyrite; several varieties of galena, differing slightly from one another in their small contents of silver, bismuth and tellurium; altaite; hessite; galenobismutite; alaskaite; aikinite; gold; tennantite; argentite; and perhaps sphalerite and arsenopyrite. With the exception of gold, the age relations of these minerals are difficult to determine. As shown in their descriptions, they all appear contemporaneous and hypogene. Gold may be in part contemporaneous, but most of it is distinctly later. Where minerals of this stage occur so that they can be mined alone, as at the Tucson mine, they constitute high-grade ore. Elsewhere their presence in small amounts has served to increase greatly the value of what otherwise would be low-grade pyritic or zinc-lead sulphide ore. The distribution of the bismuth ores corresponds closely to the distribution of gold ores, though not so general. It seems probable that most of the gold in the district was deposited during the "bismuth stage." These ores occur relatively near the supposed centers of mineralization in Breece and Printer Boy Hills or deep down along the Tucson-Maid fault, which is one of the well recognized channels of mineralization in the Iron Hill and Graham Park areas- Consideration of the high-grade nature of this mineralization and the fact that it appears to be found relatively close to the source of mineralization suggests that prospecting along some of the known channels, even deeper than they have yet been prospected, may offer hope of commercial success.

Jan 1, 1939

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By T. D. Yensen

I. INTRODUCTION IT is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its -magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current Josses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that; indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use.

Jan 2, 1916

By S. B. Christy

The practice of the cyanide-process of gold-extraction has brought to light many important contradictions of familiar chemical analogies, which still obscure both the theory and the practice of the art with distinctions subtler and more difficult to make or follow than those which delighted the heart of the old-time metaphysician. Yet Nature herself has drawn these distinctions; and if we hope to succeed in this modern search for the Golden Fleece, we must be able to follow her through the winding labyrinth. There are so many phases of this question that I shall attempt to touch on only one of them at this time, but it is one that lies at the root of many others. In reviewing my paper on " The Solution and Precipitation of Cyanide of Gold,"* Mr. E. B. Wilson contends† that" in the solution of gold by means of alkaline cyanides the various reactions are determined, as to their order and intensity, by the relative position of the elements concerned in the electro-chemical series, or series of voltaic tension." In a modified form this statement is probably true. That is to say, the difference of electrical potential in any closed electrical circuit determines the nature of the reactions which ensue. But the matter is not so simple as Mr. Wilson assumes. Recent investigations show that the order of the metals in the electro-chemical series depends not only on the nature of the elements themselves, but also on the chemical composition of the solution in which they are placed; its degree of concentration; its temperature; and, in the case of gases, on the pressure. Unless all these conditions are taken into account, inferences drawn from the electro-chemical series are likely to prove more

Jan 1, 1901

By Henry G. Granger, Edward B. Treville

The Republic of Colombia is the northernmost country of South America. Its northern coast line exteilds from the frontier of Costa Rica to that of Venezuela, on the Caribbean Sea. On the west it fronts on the Pacific Ocean, along the Panama Isthmus, and down to Ecuador. It is bounded on the south by Ecuador, Peru and Brazil, which latter country with Venezuela form its boundaries on the east. Its area exceeds 500,000 square miles. It is deemed unnecessary to give here a map of the country. Fig. 1, a map of the department of Antioquia, studied in connection with a good modern general map of Colombia, will explain itself. Fig. 1 contains also some of the region of the Cauca valley, described in this paper. Access.—The interior of Colombia is reached through the ports of Sabanilla and Cartagena on the Caribbean Sea, each of which places is connected with the Magdalena river by a short narrow-gauge railroad, running respectively to Barranquilla and Calamar. From these points lines of river-steamers serve the ports of the upper Magdalena, which they reach in journeys of a week to ten days. After leaving the steamer, a short railroad journey, followed by a long and tedious mule-ride, reaches the cities of Bogota and Medellin. Quibdo, at the head of the navigation of the Atrato, and its most important town, is connected by steamer-service with Cartagena, by canoe-routes with the various districts of the Choco, and by mule-road, at present well-nigh impassable, with the heart of Antioquia. On the western coast the port of Tumaco is a starting-point for canoe- and mule-travel to the southern part of the department of Cauca, while Buenaventura is the port of the central section of the valley of the Cauca,

Jan 1, 1899

By J. H. Jackson, J. G. Kura, M. C. Udy, L. W. Eastwood

The melting and casting of any commercial metal depends upon the success with which the problems attendant to the handling of the specific metal are overcome. Common difficulties encountered in the handling of commercial metals are tendencies to burn or oxidize excessively, low fluidity, entrapment of dross, hot cracking, cold embrittlement, cold shuts, and un-soundness caused by gas evolution. Beryllium is not only subject to these same difficulties but is generally more sensitive to them than are the more common metals, thus necessitating more exact founding precautions. Characteristics of Beryllium Certain characteristics of beryllium which make it particularly difficult to handle in the plant or laboratory are as follows: 1. The melting point of beryllium is about 2400°F and pouring temperatures vary from 2600 to 2900°F, depending upon the degree of fluidity required. The extreme chemical activity, combined with the high temperatures, makes necessary the use of inert atmospheres, slags, or vacuum for protection during melting and pouring. Furthermore, beryllium tends to react with the melting crucibles, tools, and molds, thus requiring the selection of suitable materials and proper maintenance of these items. 2. The very marked absorption of gas by molten beryllium and the subsequent evolution of gas during solidification causes a great deal of difficulty with unsoundness. Beryllium castings may also be subject to unsoundness as a result of gas formation by chemical reaction with the mold surface during solidification. 3. The very marked chemical affinity between molten beryllium and the normal atmosphere causes the formation of dross. On relatively quiescent melts, this dross forms a very tenacious film which, if carried over to the mold, can cause defects such as the formation of skins or dross in the interior or on the surface of the casting; folds or defects similar to cold shuts may also be found. 4. During the pour and attendant turbulence, the dross may be mixed into the metal and then carried to the casting. There it may be entrapped during freezing and cause internal defects, or it may float to the surface and cause severe dross defects on the cope side of the castings. 5. Solid beryllium is very weak at a temperature near the solidus line; brittleness is also a problem at lower temperatures. Thus, hot and cold cracking must be guarded against. Scope of the Experimental Work All of these problems have been given consideration in the work at Battelle. Before the work was started at Battelle, it was customary to melt beryllium in a vacuum furnace or under flux in graphite-lined induction furnaces. Because of the difficulty of preventing gas unsoundness in beryllium castings, an investigation was undertaken primarily to study this particular problem and, secondarily, to devise methods of overcoming the other difficulties encountered in the founding of beryllium. The objectives of the laboratory work were multifold: 1. To devise a practical method of melting, other than vacuum melting, by means of which consistently sound beryllium castings could be produced. 2. To obtain fundamental data which would promote a better understanding of the causes of gas unsoundness in beryllium. 3. To develop a casting technique which would permit low melt temperatures, minimize dross defects and hot cracking, and eliminate reaction with the mold surface. Up to the present time, a considerable amount of progress has been made on the first and third objectives, with the result that it can now be safely stated that consistently sound castings can be made by the open-pot melting method, using argon as a protective atmosphere and a proper casting technique. There has been some progress on the second objective of the project, but it cannot yet be safely stated that the problem is completely understood. Most of the experimental work has been conducted in an enclosed melting and pouring apparatus in which very-close control of melting variables has been effected. Findings based on the results of the work conducted in this small experimental apparatus have been applied to large-scale melts which have been made by techniques suitable for duplication on a commercial scale.

Jan 1, 1950

By R. T. Hukki

THE accepted basis of comparisons between mills of different diameter is the percentage critical speed. If n = actual mill speed, rpm, nc = calculated critical speed, rpm, np = calculated percentage critical speed, and D == inside diameter of the mill in feet, then n, In the following analysis capacity, T, is expressed in short tons per hour, tph, and power consumption, P, in kilowatts, kw. Accordingly power consumption per unit of capacity, P will be expressed in kilowatt hours per short ton, or kw-hr per ton. In all equations D refers to the inside diameter of the mill in feet and v to the peripheral speed of the mill in feet per minute inside the liners. ' Comparison between separate mills must be based on equivalent grinding conditions, i.e., same feed, same size distribution of feed, same size distribution of product, and same percentage of solids. In addition, comparisons between separate rod mills must be based on the same rods, same type of liners, and same percentage rod load. Comparisons between separate ball mills presuppose the same balls, similar liners, and same relative ball load. The practical np-range through which the equations apply varies, being narrower for fine grinding in ball mills and wider for coarse crushing in rod mills. The Relationship between Capacity and Speed It is the general belief that the capacity, T, of a tumbling mill is directly proportional to the speed of the mill, other things remaining constant.' Mathematically this is represented by the equation T - c¹ n tph [4] where c, is a factor related with the grinding characteristics of the ore, method of reduction, and the units chosen. It is proposed here that the general equation relating mill capacity and speed should be of the form T = c¹ nm tph [5] In other words, the capacity should be proportional to the mill speed raised to power m, the numerical value of the exponent being 1 5 m 5 1.5, depending on the circumstances. Eq. 5 can also be written in the following forms: T = c, (np)m tph, and [6] T=Ca vm tph, [71 where v = peripheral speed of the mill in feet per minute. If the observed capacity of a mill at speed n¹ is = T¹ tph, the capacity T² of the same mill at speed n² should be T² = T¹ (n²/n¹)tph [8] The Relationship between Power Consumption, Mill Diameter, and Speed The only well known theoretical deduction relating power consumption, P, and mill diameter appears to be the formula of duPont introduced by Gow, Guggenheim, Campbell, and Coghill.' According to duPont, the power required to operate a mill is a function of the mass of the balls, of the lever arm of the ball mass, and of the speed of the mill. The ball mass per unit of mill length is proportional to the square of the diameter, the lever arm is directly proportional to the diameter, and the critical mill speed or any percentage thereof is inversely proportional to the square root of the mill diameter. Following this reasoning, the original duPont formula is of the form P = c4D² c D • c6D-0.5 = c7D2.5 [9] If the mill speed in the above equation is expressed in terms of Eq. 3, the duPont formula may be written as follows: P=f1(D2) f2(D) f³(—np) or [10] vD P = c np D2.5 kw [11] Eq. 11 may also be derived from the mechanical principle of force, which is equal to mass x acceleration. Power necessary to operate a mill may be considered to be an homogeneous linear function of the force developed. Ball or rod mass per unit of mill length is a function of D2. The acceleration factor of the ball or rod mass is a function of the peripheral speed of the mill. Thus P = f4(F) = /x(D2) f5(v) Indicating that v = nDn, and n = c9 np /vD, the above equation becomes P = f2 (D2) -fa (D ca np/vD

Jan 1, 1955

By Bob J. Rawicki

TYPES OF WET DUST COLLECTORS Basically, there are two types of wettype dust collectors. One is mechanical, incorporating pumps, motors, fans, sprays, filters, or flooded beds. These come in many forms, but their operating principle is basically the same. The screen or flooded bed is wetted by a series of sprays. Polluted air is drawn in through a fan; here the dust particles impinge on the screen and are flushed off into a settlement tank. The air then passes through spray eliminators to the atmosphere. A great deal of time and money has been spent developing this type of collector. In laboratory tests where clean water at constant pressure, air at constant volume, and dust at low but constant mass to volume were applied, these collectors gave high percentage dust collection efficiencies. Theoretically and technically, they are very good. In practice, however, under rugged mining conditions where there are no constants, and dust load, particle size, water pressure, and volume of air vary with time, their efficiency varies dramatically. Some of the most common problems are: 1. clogging of screens 2. blocking of nozzles 3. replacement. of damaged pump stators Any of the above result in loss of air flow and dust collection efficiency. Generally, there are so many mechanical moving parts, something is always breaking down. This type of collector is very expensive in parts and labor to maintain. The second type of dust collector, which I personally developed, with the help of the British National Coal Board of Great Britain, has none of the above mentioned problems and it works on a completely different principle. My collector, the Mark III Precipitaire Wet-Type Dust Collector, (an improved version of previously successful models) has no internal moving parts, no flooded beds, screens, spray nozzles, etc. It is highly efficient - 99.8% efficiency on total collected dust and 97% on respirable dust. The pressure drop through the collector is constant, hence, air flow remains constant. There is no maintenance expenditure, be it labor or parts. The only maintenance that there is, is desludging. This, of course, varies with the dust load. With a low dust load, desludqinq may only be required every 4 weeks, but this is a very simple operation that can be handled by unskilled men and it takes only a very short time. My collector is powered by a ventilation fan that is placed on the clean air side for a longer fan and motor life. Dust is extracted solely by water action. The collector's operating principle is: Dust laden air is drawn in along ducting into a tapered scrubber section, shaped to create a self-induced curtain of water. This action washes the dust particles from the air and the collected dust settles into the bottom of the tank. Cleaned air is then exhausted via a series of spray eliminators where it is completely dried and on into the atmosphere. These collectors have been sold in Great Britain, to the National Coal Board, and throughout Europe. They have been working very well for many years now. GENERAL APPLICATIONS Dust is very dangerous; silicosis and black lung kill and disable many workers each year. Many of the mine explosions can be attributed to coal dust. By the use and application of dust collectors, these deaths and disasters can be avoided. There really is no excuse. However good and efficient a dust collector may be, it's positioning and installation arrangement is critical. The collector may remove 99% of dust supplied to it, but it takes the skill and experience of a dust control engineer to design and fit ducting, hoods, etc. to remove polluted air at source and deliver it to the collector. In some cases this is very simple; in the case of longwall machines, it is very difficult. In general, dust collectors should be used to collect dust at every point of dust generation. I have noted a great reliance on dilution as a means of dust control. I personally think this is a dangerous and unreliable method. As mines become deeper and the use of larger and more productive equipment becomes more common, reliance on dilution will be impossible and dust collectors will be essential.

Jan 1, 1982

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult's law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl' who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By Jean-Jacques Prompsy, J. S. Rinehart

Some time ago a study was initiated at the Colorado School of Mines in an effort to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. The study has been divided into three phases involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, a range commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a region in which the dynamic effects are greatly exaggerated and made more identifiable. The ultimate objective is to provide basic data which will enable the mitigation through judicious design of the frequency and severity of these transient concentrations of intense stress, thereby prolonging and increasing drill efficiency. This paper presents results of the third phase of this study — the development of a better understanding of the dynamics and mechanics of failures caused by transient stress-wave interactions. The impulsive loading or transient waves in these experiments were generated by detonating small explosive charges placed on the ends of Plexiglas cylindrical rods terminating in truncated cones. Under such intense loading, dynamic effects are greatly exaggerated and, hence, made more identifiable. The explosion generates a high-intensity transient stress disturbance which moves through the rod, reflects from surfaces which lie in its path, and establishes momentarily narrow regions of high concentrations of stress where failure of fracture may occur. The peregrinations of these waves, their interactions and their effects have already been described in the literature (see, for example, Refs. 1 and 2). The locations and extent of the regions quite apparently are strongly dependent on specimen shape, making it possible through judicious shaping of specimens to relocate the highly stressed regions, minimize their extent, or eliminate them entirely. These experiments were designed, first, to identify more clearly the vulnerable regions in geometries relevant to drill-bit design and, then, to modify these regions in a predictable way by changing specimen shape. Through this latter process, it is anticipated that better bit design might evolve. The specimens used in the experiments were cylindrical rods, 1 1/2 and 1 1/8 in. in diameter, ended by a truncated cone, with the cone angles ranging from 45° to 130°. Upper cone face diameters were 1/2, 3/4, or 1 in. A small plastic-covered electric blasting cap detonated on the axis of the specimen produced the spherical shock wave. The detonators used were Olin Mathieson No. 6, which induced into the rod a transient saw-toothed stress disturbance of about 3-microseconds duration, corresponding to a wave length of 0.3 in. in the Plexiglas. Five distinct systems of fracture were observed: (1) along the axis of the rod, a lower system of fractures, the cracks focusing around one point for specimens having cone angles of 80° and 90° and, as the cone angle was increased, spreading downward; (2) just above these fractures, an upper system of fractures composed of horizontal cracks observable in some specimens but not of any appreciable extent; (3) a third system of axial cracks still above the latter, observable in the small cone-angle specimens; (4) in the upper part of the specimen, a system of radial fractures extending from the blasting point; and (5) circular spalling due to reflection of the wave on the boundary of the cylinder. Only the first three systems, the axial fractures, are examined here. LOWER TENSILE FRACTURE SYSTEM The first, lower system of tensile fractures, shown in the photograph of Fig. 1, was observed in almost all of the specimens. It was due to the reflected tensile wave coming in from the boundary of the cylinder as shown in Fig. 2. The reflected wave was cylindrically convergent and focused

By J. L. Bray, S. T. Ross

The paper provides electrometallurgical data on the problem of germanium removal from zinc sulphate solutions. Germanium traces have caused much concern to the zinc refiner. Confirmatory evidence of interaction between germanium and cadmium is presented. Statistical analysis of data expands its significance and enhances its value. Further research is outlined. THE literature contains many references to the effects of trace amounts of germanium in the production of electrolytic zinc. One of the authors had experience with this troublesome element as early as 1917 at Trail, B. C. In 1929, Tainton and Clayton' reported that concentrations of as little as one part per million of germanium were sufficient to cause serious losses in current efficiency. Liddell2 reported that trace amounts of germanium cause marked lowering of the hydrogen overvoltage of electrolytic zinc cells, so that commercial production was impaired. Bray3 recorded the history of germanium in relation to electrolytic zinc production, noting that concentrations below 10 ppm have been found to yield low current efficiencies and copious hydrogen evolution. Koehler' stated that germanium "when present to the extent of a small fraction of one part per million per liter, causes serious evolution of hydrogen with a corresponding reduction in current efficiency." Recently, however, S. W. Ross" reported, from Risdon, Tasmania, that "in the course of leaching . .. dissolved traces of germanium... if not removed almost completely ... increase the reversion of cadmium during the filtration of the copper-cadmium precipitate and reduce the current efficiency during subsequent analysis." The copper-cadmium precipitate referred to is the residue from the zinc-dusting purification of zinc sulphate leach solutions. In the face of such conflicting testimony and with the increasing industrial importance of pure germanium and zinc it was decided to investigate the relationship between cadmium and germanium. Furthermore, other work by the authors showed certain discrepancies to exist in the theories of Tainton, et al. In the laboratory, without marked efficiency decreases, the authors have deposited zinc successfully from solutions containing as high as 1 g per liter of germanium. This could be done only when there was no cadmium present. Preliminary investigations of the suspected rela- tionships were carried out by means of emission spectrographic analysis using a beryllium internal standard. Several solutions containing 100 g per liter of zinc, as zinc sulphate, and 1 g per liter of cadmium, as cadmium chloride, were prepared. These concentrations were on the order of those obtained during a commercial low-acid leaching process. Varying concentrations of germanium were added to these solutions so that the range of 0.0000 to 0.5000 g per liter of germanium was covered. A 250 ml sample of each solution was agitated with 2.5 g of zinc dust for 30 min, filtered, and the filtrates were examined spectroscopically. Qualitative evidences of cadmium traces were found in those filtrates which originally contained above 10 ppm of germanium. Reliability of the analytical method did not permit quantitative investigations since cad-Table I. Current Efficiencies Obtained at 0.0000 and 1.5000 G per Liter Cadmium Concentrations Ge Concentrastion,* Cd Concentration,* EtBclenoy, G per Liter G per Llter Pot 0.0000 0.0000 84.270 0.0010 0.0000 94.849 0.0050 0.0000 92.649 0.0075 0.0000 94.039 0.0100 0.0000 96.084 0.0000 1.5000 93.460 0.0010 1.5000 95.158 0.0050 1.5000 92.148 0.0075 1.5000 91.260 0.0100 1.5000 84.546 • Cd and Ge concentrations shown are those existing before zinc-dust purification. mium determination in the concentrations present in zinc-dusted solutions lacks sufficient sensitivity for reproducible results. As a consequence of the inability of the investigators to obtain acceptable results through direct quantitative analysis, an indirect approach was devised. This indirect method involved a study of the current efficiency, in a model zinc cell, as a function of the concentrations of cadmium and germanium. Variables such as cell temperature, voltage, current density, anode spacing, relative electrode area, degree of agitation, cathode preparation technique, time, acid concentration, and solution volume were held constant. Fig. 1 shows the cell used. The current was fur-

Jan 1, 1952