Search Documents

By J. W. Spretnak, H. R. Ogden, A. G. Imgram

The effect of working reduction, stress-relief annealing, and recrystallized grain size on the tensile and notch-tensile properties of molybdenum and Mo-0.5 Ti was studied. It was found that increasing the amount of working reduction increased the strength and reduced the tendencies toward brittle behavior. Stress -relief annealing did not alter the strength but lowered the transition temperature. Increasing the recrystallized grain size lowered the strength and raised the transition temperature. The notch -unnotch strength ratio began to decrease with decreasing temperature at temperatures below those at which the notched ductility fell to zero for all of the micro structural conditions investigated. BEING bcc metals, the refractory metals in Groups Va and VIa (V, Cb, Ta, and Cr, Mo, W) undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures. Previous research has shown that molybdenum and tungsten not only have higher transition temperatures than columbium and tantalum but show a marked sensitivity of transition temperature to structure as well.' Recrystallized materials become brittle at considerably higher temperatures than is the case with material having a worked or fibered micro-structure. Evidence of structure sensitivity has also been detected in columbium- and tantalum-base alloys containing appreciable amounts of molybdenum or tungsten such as F-48 (Cb-15W-5Mo-1Zr) and Ta-10w.2 This paper describes the results of research conducted to further evaluate the effects of metal. lurgical structure on the low-temperature tensile and notch-tensile properties of molybdenum and Mo-0.5Ti. The effects of rolling reduction, stress-relief annealing temperature, and recrystallized grain size were studied. Considerable progress has been made in explaining the fundamental mechanisms of the flow and fracture characteristics of bcc metals. Several of these concepts are helpful in interpreting the data obtained in this study. Brittle fractures occur when the highly temperature-sensitive yield strength equals, or exceeds, the temperature-insensitive brittle cleavage fracture stress.3 The rapid increase in yield strength with decreasing temperature, characteristic of all bcc metals, is therefore of primary concern. petch4 has described the yield strength, ay, (stress required to initiate plastic flow) of bcc metals by the expression where ai is the frictional resistance to slip, Ky is a constant numerically equal to the slope of a a vs curve, and 2d is the average grain diamefer. The oi term itself is thought to be composed of a temperature-insensitive component dependent on impurity content and second-phase particles and a temperature-sensitive component dependent on the Pierls-Nabarro force.5 This equation has also been demonstrated to hold for the flow stress (stress required to maintain continued plastic flow).' Brittle-crack nucleation is thought to occur by the coalescence of dislocations piled up in slip planes at sessile dislocations or twin and grain boundaries.7,8 These proposed mechanisms require that a large number of dislocations be released into the active slip planes so that sufficiently large stress concentrations are produced at the dislocation pile-ups to enable coalescence into a micro-crack. Therefore, at least a microscopic amount of slip must occur in some grains to facilitate initial crack formation. Cottrell 7 has predicted that brittle fracture, nucleated by slip, should occur when where ty is the shear yield strength, ß = 1 in un- notched xension, u is the shear modulus, and y is the effective surface energy. This equation incorporates the Griffith concept of fracture that a crack will propagate if the decrease in strain energy equals or exceeds the increase in surface energy.

Jan 1, 1964

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"'. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By F. V. Lenel, J. A. Dromsky

The influence of thermal and mechanical treatments upon the elevated-temperature stability, the microstructure, and the mechanical properties of aluminumaluminum oxide alloys is investigated. Compacts from atomized and flake aluminum powders were sintered at temperatures just below the melting point of aluminum in a vacuum of 10-4 Torr for several hours and were then hot-extruded. During this treatment the hydrated oxide present on the surface of the powder particles decomposes, the water vapor produced reacts with the aluminum forming additional oxide, and the hydrogen developed is removed by diffusion to the surface. Extrusions of compacts so treated are stable at temperatures up to the melting point of aluminum and do not form blisters and internal defects typical of extrusions from untreated powder. Electron micrographs of extrusions from unsintered compacts show long parallel oriented platelets typical of the IN previous investigations1,2 the properties and structure of aluminum alloys were described which had been produced by cold compacting aluminum powder and then hot pressing and extruding the compacts. Both the structure and the properties of these alloys differ significantly from those of commercially produced aluminum-aluminum oxide alloys. When commercial alloys are produced, they are given a sintering treatment in air at about 600°C between cold compacting and hot pressing.3 During this treatment the hydrated oxide, which forms the coating on the aluminum-powder particles from which the alloys are prepared, is decomposed.4 The chemically bound water which is released reacts with the aluminum and forms aluminum oxide and hydrogen. Most of the hydrogen is eliminated by hydrated oxide skins on the original powder particles, while the oxide particles in extrusions from sintered compacts are broken up. The strength of extrusions from treated powder is somewhat lower, but their ductility is considerably improved over that of extrusions from untreated powder. The slip-trace patterns on electron microgvaphs of extrusions which had been strained in tension before replication indicated that the grain size of the extruded alloys was approximately the same as that of the original powder particles. Coarse-grained alloys were produced by severe cold work and annealing of the extrusions. They have significantly lower room-temperature strength, but about the same ductility as the vacuum-sintered fine-grained alloys. The size and shape of oxides in the coarsegrained alloys is similar to those of the fine-grained alloys, but the particles are somewhat more uniformly distributed. diffusing to the interior or exterior surfaces of the compact, but it is difficult to eliminate all of it because the solubility of hydrogen in solid aluminum is very low even near its melting point. Extruded alloys which are not sintered before hot pressing and extrusion appear quite sound upon metallo-graphic examination, but develop severe surface blistering and internal fissuring when they are heated to elevated temperatures after extrusion. Fissures and blisters have been observed even in commercial alloys which had been sintered in air, although they are much less severe.&apos; Because of the importance of this sintering treatment it was studied in this investigation in a modified form, using vacuum sintering rather than sintering in air, to insure more complete elimination of occluded hydrogen. The technique is described and the effect of the treatment upon the structure of the alloys is documented. It has been known for some time that extruded aluminum-aluminum oxide alloys are very finegrained, but an exact delineation of grains in electron micrographs has not been possible. In the conventional metallographic-etching techniques etchants attack the interface between the second-phase particles and the matrix in the alloys much

Jan 1, 1964

By L. Yarborough, L. R. Smith

This paper presents results of a laboratory study of retrograde condensate recovery by revaporization into dry injection gas. Flow tests were performed in 10.6-ft long sand packs at 100F and 1,500 psi. In three runs methane revaporized the liquid from a n-pentane-methane mixture in the presence of immobile water. TWO of these tests were water-wet, and the third was totally oil-wet. In the three runs n-pentane recovery was complete after 2.5 hydrocarbon PV of injection. There was no significant performance difference between the two wettability extremes. In a fourth experiment, a methane-hydrogen sulfide mixture revaporized a synthetic light, sour condensate. No water saturation was present. Equilibrium compositions and volumetric data were obtained for the four-component condensate. The heavy component, n-beptane, was removed after 6 PV production. Comparison of the effluent fluid compositions with known equilibrium data shows that the flowing fluid was equilibrium vapor and that the mixing zone between equilibrium vapor and dry injection gas was short. Data indicated that complete recovery of retrograde liquid occurred after it was contacted by a sufficient quantity of dry gas. INTRODUCTION When pressure declines below the fluid dew point in a gas condensate reservoir, a liquid phase forms. In this process, referred to as retrograde condensation, the quantity of liquid formed is frequently small enough that the liquid is not a flowing phase. To prevent loss of valuable retrograde liquids, the process of dry gas cycling has been employed for several years as a more or less standard practice. In this procedure the reservoir pressure is maintained above the fluid dew point so that the liquid components may be produced as vapor and then separated at the surface. Although full pressure maintenance by gas cycling seems ideal in terms of preventing liquids loss, several factors can reduce the atuactiveness of such an operation. From a study of a condensate reservoir in Alberta, Canada, Havlena et a1.1 con-cluded that cycling under conditions of declining pressure leads to economic advantages and to a high recovery of hydrocarbon liquids. This study considered effects of volumetric sweep efficiency, retrograde behavior of the original wet gas and revaporization characteristics of the retrograde liquid when contacted by dry gas. The first major work concerning revaporization of liquid in a gas condensate system is that of Standing et a1.2 Calculations based upon the PVT behavior of a recombined gas condensate fluid indicated that all retrograde liquid can be recovered if it is contacted by a sufficient quantity of dry gas. The paper considered the effect of variable permeability upon the recovery of retrograde liquid. Standing et al. concluded that recovery of heavier components in the retrograde liquid is greatest if reservoir pressure is allowed to decline below the dew point prior to dry gas injection. Since the work of Standing et al., several laboratory studies have been reported which show that recovery of hydrocarbon liquids by vaporization into dry injected gas can contribute to increased recovery above that obtained by ordinary production practices. Vaporization from retrograde condensate,3 conventional oil4-7 and volatile oil8 reservoirs has been considered. There is little work that deals with revaporization recovery from condensate reservoirs. This study demonstrates that vapor-liquid equilibrium exists when a dry gas is injected into a porous medium containing retrograde condensate; investigates the effect of wettability on revaporization of retrograde condensate; and provides an indication of the amount of dry gas necessary to

Jan 1, 1969

By R. R. Goddard

By use of the frequency response method with a radioactive tracer, it was possible to determine fluid dispersion and distribution in a natural consolidated and an unconsolidated medium. Measurements were made in a linear flow system at oleic saturations of 69 per cent in the consolidated medium, and 100 per cent in both media. Dispersion and distribution were obtained by measuring the amplitude attenuation and the phase velocity of sinusoidal waves with a dual monitor apparatus. The gamma ray emissions permitted in situ measurements at any distance along the porous samples. One result of importance was that the effective diffusivity increased as the wave length increased. As a consequence, a dispersion coefficient appropriate for the injection of large slugs might exceed the value measured by use of small slugs. Since flow models based solely on fluid velocity and an effective diffusivity coefficient imply that the diffusivity should be independent of frequency, such representations were not adequate for the data of this study. A comparison was made with a capacitance model of porous media with deadend PVs, but even this model was not completely adequate. By using attenuation and phase velocity data, fluid dispersion can be predicted without postulating a differential equation satisfied by the tracer concentration, thereby eliminating the need of a complicated model to represent dispersion. INTRODUCTION The flow of similar miscible fluids through a porous medium can be fairly adequately described by two parameters: the average fluid velocity and the effective diffusivity.1-3 It has been pointed out recently, however, that significant discrepancies exist between this representation and the experimental data.4-7 An improved agreement can be obtained by introducing additional parameters based on the concept of dead-end pores. The purpose of the present investigation was to find out whether the frequency response method could be used to measure the relevant parameters. The method was used in the following form. A stream of fluid was flowed at a constant rate through a sample of porous material and the concentration of a radioactive tracer in the fluid was varied sinusoidally at a fixed frequency. The effects of flow through a porous medium are a decrease in the amplitude of the concentration wave and an increase in the velocity of the peaks of the waves above the average velocity. Attenuation and phase veIocity of the waves were measured as a function of frequency and fluid velocity. The simple two-parameter model implies that the diffusivity should be independent of frequency. Data reported in this paper show that the diffusivity decreases as the frequency increases. Hence, as shown also by many others, the two-parameter model is not completely adequate. Coats and Smith 5 used two additional parameters in their model: the volume of the dead-end pores and the rate of mass transfer between dead-end pores and the flowing stream. Their capacitance model of a porous medium containing some stagnant fluid, to which transfer occurs by molecular diffusion, did not explain the dispersion results of either the present study or of theirs. Instead, the capacitance effect can be better described as the result of extreme velocity variations within the pores of the medium, with transfer between the velocity zones by convection. EXPERIMENTAL PREPARATION OF POROUS MEDIA Data reported here were obtained with a natural Berea sandstone, and with two packings of 20/25 mesh sand. Pertinent information about these media is listed in Table 1. The sandstone core was first sealed with a non-

Jan 1, 1967

By A. Steiner, E. Miller, K. L. Komarek

Equations have been derived to calculate the chemical potentials of the components of liquid binary alloys from liquidus and enthalpy data. The equations are applicable to systems with intermetal-lic compounds of limited solid solubility. The liquidus curve of the Mg-Sn system was accurately redetermined, and the melting point of the compound Mg2Sn was found to be 770.5° * 0.3°C. The thermo-dynamic properties of the liquid alloys were calcu -lated from the liquidus data. The activity of tin shows both positive and negative deviations from Raoult&apos;s law and the relative integral entropy is positive. THE phase boundaries in an equilibrium phase diagram are functions of the thermodynamic properties of the coexisting phases. Specifically, the shape of the liquidus curve near an intermediate compound is determined by the properties of the compound and the liquid phase. Hauffe and wagnerl have derived an equation for the chemical potential differences (ui) of the liquid alloys near the congruent melting point when the heat of fusion of the compound and the liquidus curve are known. In their derivation the temperature dependence of the ui value was neglected, and liquid of stoichio-metric composition was chosen as the reference state. To obtain chemical potentials over the ntire composition range of the phase diagram with the pure components as the reference state, equations have been derived which incorporate the temperature dependence of the chemical potentials. Such a thermodynamic analysis can be carried out when the liquidus curve and the enthalpy values are known. The equations have been applied to the redetermined liquidus curve of the Mg-Sn system to obtain the thermodynamic properties of liquid Mg-Sn alloys. The Mg-Sn phase diagram has been studied by various investigators and the results have been compiled and critically assessed by Hansen.2 Preliminary thermal analyses showed that the basic features of the diagram were correct. The system has one congruent melting compound, Mg2Sn, two eutectics, and some solid solubility of tin in magnesium. However, the published liquidus temperatures show considerable scatter. In order to perform an accurate thermodynamic analysis, the liquidus curve between the magnesium-rich and tin-rich eutectic compositions was therefore redetermined by careful thermal analysis using highest-purity starting materials. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd, Toronto, Canada) had a purity of 99.99+ pct with the following impurities (in ppm): 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu, <10 Fe; tin (Cominco Products, Spokane, Wash.) contained 99.999+ pct Sn. The graphite crucibles were machined from graphite rods (United Carbon Products Corp., Bay City, Mich.) which had an average total ash content of less than 30 ppm. All the graphite parts were baked out in vacuum at 950" to 1000°C for a minimum of 24 hr to remove volatile organic materials. The graphite crucibles (3 in. long, 1-5/8 in. OD, 1-3/8 in. ID) were tightly closed with a threaded cover (1/2 in. thick) which had a central thermocouple well (2-1/4 in. long, 5/16 in. OD, 3/16 in. ID). Cover and thermocouple well were machined from one piece of graphite. A thin sheath of quartz was inserted in the well to protect the thermocouple

Jan 1, 1964

By G. W. Binkley, R. E. Collins, G. K. Dumbauld

A mathematical analysis has shown that the primary factors affecting the deposition of cement in unfractured perforations during squeeze-cementing operations are: the properties of the cement slurry, the geometry of the perforations, and the filtration time. The validity of the analysis has been substantiated by laboratory investigations. The information presented in this paper makes possible the prediction of the rate of deposition of cement in and about unfractured perforations under given squeeze-cementing conditions, the proper filtration time to control the amount of deposition to any desired value, and the deposition properties needed in cement slurries to restrict to any desired degree the formation of nodes of cement .Solids inside the casing. INTRODUCTION The deposition of solids against a permeable medium by the process of filtration is an important property of a cement slurry. General recognition of the role of filtration in the use of cement in wells is evident in view of the fact that several patents on low-water-loss cements have been issued during the past few years. In the conventional, high-pressure squeeze-cementing technique, a large volume of cement slurry is usually displaced into the area surrounding the perforated interval after the formation has been fractured hydraulically.&apos; Near the end of the job, the pumping rate is slowed or stopped intermittently in an effort to obtain a high pressure in the wellbore. The way in which a high pressure is obtained is not understood thoroughly. but it is be- lieved to be caused by the deposition of a rigid mass of compacted cement particles either in the fractures of the formations or inside the casing opposite the perforated interval. In a method of squeeze-cementing introduced several years ago, a small amount of cement slurry is squeezed into the perforations at a low pressure to avoid fracturing the formation. The filling of the unfractured perforations with cement particles by the process of filtration is important to the success of this technique. Early in the development of this low-pressure squeeze-cementing technique, laboratory and field-size experiments showed that conventional, neat cement slurries were unsatisfactory if the tubing was extended into or through the perforated section of the casing. The extremely high filtration rate of neat cement slurries caused the deposition of a compacted mass of cement inside the casing and made it impossible to remove excess cement by reverse circulation and difficult to withdraw the tubing. Because the need for cements with a reduced filtration rate was obvioils and urgent, modified cements containing 12 per cent bentonite were used until research was completed on modified cements containing 25 per cent bentonite.< These modified cements were useful in the solution of the immediate problem, but the following questions remained unanswered: (I) what is the optimum filtration rate of cement slurries for this application, (2) how long should the squeeze pressure be applied. and (3) how great are the effects of squeeze pressure and well temperature on the rate of deposition? Furthermore, the relationship of the filtration properties of cement slurries to the dimensions of the perforations and the wellbore was unknown. In order to obtain information relative to these basic considerations, a systematic evaluation of all the factors involved in the deposition of Cement during low-pressure squeeze-cementing operations was initiated. Although the work was directed toward an evaluation of the factors influencing the deposition of Cement in the low-pressure squeeze-

By S. J. Burns, W. W. Webb

The dislocation arrangements formed during unsteady propagation of cleavage fractures on (010) planes in LiF have been investigated by high-resolution etch-pit techniques and by X-ray diffraction topogvaphy. In impurity-hardened crystals, cracks propagating in any direction on (010) planes at velocities of about 103 cm per sec are usually accompanied by light plastic deformation which is enhanced wherever the crack is allowed to hesitate. Dislocations with [011] type Burger&apos;s vectors are often formed looped around the crack tip. They are dragged along with the crack tips leaving edge dislocations lying nearly parallel with the clearage surface about 5µ from it. These dislocations are easily overlooked since they may initially intersect with the cleavage surface infrequently and later may disappear from the crystals due to image forces during aging at room temperature. Although the plastic work associated with these dislocations is only comparable with the reversible (010) surface energy, an instability in crack propagation appears due to a limit of the velocity with which dislocations can be dragged along with the crack. Transition to a fully brittle nonplastic fracture mode occurs when the crack velocity exceeds the velocity with which dislocations can be moved by the stress field of the crack. TRANSITIONS between brittle and ductile modes of fracture appear to be common processes in the behavior of materials in which the flow stress is close to the stress at which brittle cracks can propagate. High-strength engineering alloys fit into this category and the transition from ductile to brittle modes of crack propagation may be associated with catastrophic failures in these important materials. The methods of theoretical mechanics indicate the geometrical conditions in which these processes may occur but the detailed mechanisms controlling the generation of dislocations in the initiation of the plastic mode and the process by which the loss of plasticity occurs on transition to the brittle mode are not yet clear. Since these mechanisms are not amenable to direct observation in engineering alloys we have chosen a semi-ductile alkali halide LiF as a model system in which to observe transition mechanisms between plastic and brittle modes of crack propagation. Cleavage cracks in this system are known to undergo a plastic-elastic transition at velocities between 103 to 104 cm per secl and dislocation configurations in LiF are amenable to study by optical-microscopic observation of dislocation etch pits2 and by X-ray diffraction topography.3 We have been able to identify a dislocation mechanism responsible for the transition from brittle to slightly plastic modes of crack propagation in LiF. A model based on this mechanism permits calculation of the critical crack-propagation velocity for this transition and indicates the importance of the stress dependence of dislocation velocity in determining the critical crack velocity. Of course, this model cannot be carried directly over to more complex materials but it is quite possible that its qualitative features are generally applicable. Dislocations intersecting fresh cleavage surfaces in LiF were reported by Gilman,4 by Forty,5 and by Wash-burn et a1.6 Such dislocations were construed to have been nucleated where the cleavage crack hesitated or stopped, near stress concentrators, such as cleavage steps, on the crystal face. The loci of such dislocations deposited On the cleavage plane in bands were called "stop lines" or "deformation zones". Gilman, Knudsen, and walshl measured the velocity of cleavage cracks in lithium fluoride by evaporating thin resistive strips on the crystal side and recording

Jan 1, 1967

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-&apos;Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of&apos; (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.&apos;-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "&apos;12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger&apos;s terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

John Birkinbine, Philadelphia, Pa.: Mr. Sperry&apos;s paper is certainly a valuable addition to the literature upon alloys with iron, supplementing the data already published concerning the influence of manganese, chromium, tungsten, titanium, aluminium, etc.; and it is to be hoped that the presentation of information upon the influences of nickel may bring out comparisons with other alloys. Taking into consideration the properties of nickel, and its use as an alloy in heavy forgings, as set forth in the paper, there would appear to be no serious difficulties in utilizing this alloy by extending its application to pieces of more moderate size. The melting-temperature of nickel, as stated by Mr. Sperry, is considerably lower than those given by various authorities. Its point of fusion being so near that of iron, and its density but little greater, the difficulty of alloying it in the foundry should not be serious, particularly if it is applied as a ferro-nickel. The addition of nickel monoxide (NiO) to molten steel would appear to be less desirable than the application of metallic, nickel or of ferro-nickel, if such is produced on a commercial scale and at a satisfactory price.

Jan 1, 1896

"The method of conveying ore from the ore-pocket at the shaft collar to the railroad ore bins, whence it is transported to the reduction works, is by cars with electric haulage.The cut shows the car coupled to the electric locomotive at the moment of dumping into the railroad ore bins.The locomotives used are of several makes, usually having two 12 ½ h-p. motors of a rated draw-bar pull of about 1,200 lbs., using 500 volts D. C. Track gauge is 30 inches, and speed is six miles per hour.The car holds two skip loads-10 tons—and has sides opening outwards the full length of the car, for rapid side-dumping. One man operates car and motor, and loads and unloads the car. The trolley pole runs in both directions without reversing.Loading is clone by operating a valve connected to a compressed air lift, which raises and lowers a gate in the ore-pocket chute, the ore running by gravity into the ore car spotted under the gate of the chute. Dogs hold the sides of the car in place at the bottom, the tops of the sides being hinged, and a hand lever releases the dogs, permitting the sides by the pressure of the ore against them to open at the bottom.With little manual effort one man does the work which was formerly done, when hoisting ore with cars and cage, by 10 men under laborious conditions."

Jan 1, 1913

"The largest variety of asphalt and related bitumen deposits in this country is found in Utah. Utah is one of the few places in the world where the hydrocarbon minerals, gilsonite or uintaite, wurtzilite (trade name elaterite) and ozokerite are produced. These bitumens occur in an area embracing nearly 10,000 square miles in eastern Utah near the Colorado line. This area is largely in the western part of the Uintah basin. The bitumens are in the Tertiary horizon in the various divisions of the Eocene series.Gilsonite is an asphaltite derived from petroleum, wurtzilite is an asphaltic pyrobitu¬men derived from petroleum, and ozokerite is a native mineral wax resulting from the met-amorphosis of paraffinaceous petroleum.Gilsonite is produced by the Gilson Asphaltum Company, a subsidiary of the Bar¬ber Asphalt Company, at Watson, Utah. A narrow guage railroad, seventy miles in length and with a 7 1/2 percent grade over the Book Cliffs on Baxter Pass, was constructed by the company from the Denver & Rio Grande Western railroad main line in order to open up the gilsonite deposits. The veins range from narrow upward to 18 feet in width. The Rainbow vein at the present wokings is eight feet wide, vertical, and has sandstone walls. This vein has been opened up for a distance of about three miles and in some places four hundred feet deep. Forty men usually are employed with a production of eighty tons per day."

Jan 1, 1925

"Copper was first made in Butte by the use of iron for its precipitation from mine water in 1890. In consequence of a fire breaking out in the St. Lawrence mine of the Anaconda Copper Mining Company in November, 1889, a large quantity of water was poured into the workings, with the intention of flooding the mine and extinguishing the fire. This proved to be impracticable, but this water, on being pumped to the surface, was found to be high in copper sulphate,—tradition says 75/100 of 1 per cent. The Anaconda Copper Mining Company gave Wm. Ledford a lease on this water. He first (lug holes into the ground, filled them with scrap iron and allowed the water to flow through them. Later he built an open-top flume which he partially filled with iron and passed the water through the by the iron precipitation method. An assay in- the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level.None of the mine waters encountered in the solid rock in the mines of Butte contained copper in sufficient quantity to produce the metal profitably by the iron precipitation method. An assay in the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level."

Jan 1, 1913

By AIME AIME

Few men in the coal-mining industry have had experience in metal mining as well, as has Carroll A. Garner. He went to the Arizona copper country immediately after graduating from Penn State in mining engineering in 1910, and worked in the engineering departments of the Miami and Inspiration companies for two years. Then he came back to Penn State far a year as an instructor in mining engineering before embarking in the coal industry. He was born in Ashland, Pa., July 6, 1889, and reared there, in the heart of the anthracite district, which undoubtedly influenced his choice of a professional career. The green Pennsylvania hills were preferred to the Arizona cactus country. His first coal-mining job was with the Lehigh Valley Coal Co., of which he was division engineer at Hazleton when he joined the Institute in 1917. He gave that up to go to Ohio as head of the Fernwood Mining Co. in 1921, but even that was too far west and after two months he was back in Pennsylvania as assistant general manager of the company that has since monopolized his services the Jeddo Highland Coal Co. Since 1927 he has been vice-president in charge of operations of both the Jeddo-Highland and the Hazle Brook Coal Companies, Jeddo, Pa. Between them they normally produce about 1,500,000 tons of what Mr. Garner will readily admit is the very highest grade of anthracite, utilizing the services of some 2600 men.

Jan 1, 1942

By Forrest K. Pence

BENTONITE deposits are known to occur in Texas within the Jackson group of formations. This group represents the uppermost Eocene age sediments found in the coastal plain area of Texas. It outcrops across this area of the state in a narrow band of some 4 to 20 miles width. The outcrop pattern roughly parallels the present Gulf of Mexico shore line and is some 100 miles inland from the Texas shore, Fig 1. The principal bentonite deposits are found in the areas where this outcrop pattern cuts across the south-central Texas counties of Karnes, Gonzales, and Fayette. In these deposits, the better quality bentonite is found in the lower or bottom layers of the volcanic ash deposits in which they occur. Some of these better quality bentonites develop very light colors upon firing and therefore justify their being classified as "white firing." The deposits in Karnes and Gonzales Counties apparently occur in commercial quantity, whereas the white firing strata so far uncovered in Fayette County have been too thin to be classified as yet as "commercial." A study of the ceramic properties of the weathered ash in Gonzales and Karnes Counties was reported in 1941.1

Jan 1, 1949

By H. C. George

CAREFUL- sampling and good judgment as to probable recoveries are important factors in estimates of ore reserves, based on prospecting drilling results, but other factors are equally as important and may be more misleading and perhaps disastrous if not properly interpreted. Some of these are: 1. The case where no, ore is shown in the "sludgings," when, as a matter of fact, the drill has passed through a thick sheet of ore which has been broken up and washed away into open crevices. In numerous cases, later mining operations have shown that this has happened. This condition may be discovered by shooting the drill .hole at the point where the open crevices occur, but shooting should not be done until after the drill hole is completed, because the resulting shattered formation may salt the drill hole at lower levels. 2. The case where rich cuttings are shown for a thickness of 20 or 30 ft., when ore was encountered in only the first sludging. Owing to soft or loose formation, the ore from the first sludging has salted the lower sludgings. The presence of large pieces of ore and a similar ratio between zinc and iron assays in the lower sludgings frequently indicate this condition. In the lower sludgings, the presence of oxidized ore in unaltered limestone sometimes shows this condition. 3. The case where the drill hole shows a considerable thickness of ore; but owing to the presence of a vertical sheet of ore, perhaps not more than 1 in. thick, at the place where the drill hole is located, the good assays resulting might be misleading. If this condition is suspected, the drilling of several more holes within a distance of 10 or 15, ft. will usually show it.

Jan 1, 1921

By F. H. Wilson, E. W. Palmer

Brass mills are familiar with a recurring problem which reveals itself during deformation of annealed metal as an opening up of cracks which are suggestive of a grain boundary pattern. A typical example is seen in Fig 1, which shows part of the convex surface of a cartridge brass disc which was slightly dished by the punching operation. Another illustration of the same type of defect was found in the surface of a finished cartridge case which split open on firing. These cracks, shown in Fig 2, were away from the split but indicate the presence of the type of weakness which permitted the splitting. Usually the weakness consists of separate cracks, the lengths of which are of the same order of magnitude as the grain size prior to the final anneal. Their typical appearance in a polished section is shown in Fig 3. This structure was found below the surface of a fractured tensile-specimen that had been cut from a large cartridge blank showing the defects on its convex surface. While the pattern formed by these cracks suggests a grain boundary origin, the cracks bear no relation to the currently existing grain structure. Thus Fig 3 shows that the grains have grown up to cracks already present. Since it is doubtful that the cracks were present in the metal before the anneal, they must have formed during the anneal but prior to recrystallization. The term "fire-cracking" has been generally applied to cracking that occurs during an anneal under the influence of internal stress, but refers more specifically to obvious macroscopic cracking attributable to the presence of a low melting phase, usually lead. Since the type of cracking described above may occur when the lead content is very low, we have considered it a somewhat different phenomenon, and have called it "inter-granular parting." While most examples involve cartridge brass, intergranular parting has also been observed in the fabrication of large seamless tubes from discs of both 85/15 red brass and 70/30 cupro-nickel. Similar cracking in nickel silver was investigated by Jones and Whitehead,1 who showed that it could occur during healing or cooling. That which occurred on heating they called "fire cracking," and they suggested that, a transformation at about 320°C might account for its occurrence. It was felt in this laboratory that the observed parting was probably one aspect of the general observation, first made by Rosenhain and Archbutt,2 that a tendency toward intergranular fracture under tensile stress increases with increasing temperature and decreasing rate of strain. In this case the stress involved would be internal. The rate of strain would be exceedingly slow, a localized internal creep. Reference to the literature uncovered no efforts to extend the observations of Rosenhain to conditions involving only internal stress. Accordingly, an exploratory research, sufficient in detail to satisfy us as to the probable truth of this explanation of the observed intergranular parting, was undertaken. The internal stresses present during the early stages of an anneal (prior to recrystallization) would be from two sources: residual stresses developed during deformation, and thermal stresses caused by uneven heating and expansion. Thermal stresses would vary widely according to shape, size and manner of heating, and can be considered as supplementary to residual stresses. It seemed necessary to determine the stress and temperature conditions under which parting would occur in a relatively short time, and then to establish whether or not in- ternal stresses may persist to an extent adequate to cause parting at such temperatures. (Jones and Whitehead1 and Moore and Beckinsale3 made tests which indicated that stress relief required an appreciable time.) During the course of the research the desirability of studying the effect of grain size became apparent, and this factor is one of the major variables of our investigation. Intergranular Parting under Tension at Elevated Temperatures In early experiments, hard 70/30 brass tensile specimens, with unknown residual stresses, held for 10 min. at applied stresses from 30,000 to 40,000 psi at temperatures from 300 to 350°C, showed no macroscopically visible cracks when unloaded and cooled, but cracks very similar in appearance to those observed in commercial practice were revealed in these specimens by pulling them to fracture. Annealed specimens, on the other hand, showed no cracks in such experiments, apparently because they deformed plastically at stresses below those necessary to cause parting in a reasonable time. Hence, the specimens used for this study were first strengthened by cold tensile elongation, giving them an unavoidable residual stress pattern (determined largely by grain size and orientation) which would, however, correspond in direction, at least, to the stress pattern obtained under stress at temperature. A variation in these residual stresses might be expected with variations in grain size, but following any given anneal the reproducibility of stress pattern should be as good as that of the grain size measurement. With no information as to the effect of the amount of prior deformation, tests were conducted on specimens given the same cold elongation, using a stress applied at temperature which was a constant proportion of the stress required to produce this elongation. In

Jan 1, 1950