Search Documents

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By Frank Firmstone

When in charge of the Glen don Iron Works, the importance of good methods of filling was forcibly brought to my attention, and it occurred to me that the first step toward the discovery of the best plans was the accumulation of exact information as to the distribution actually effected by various chargers; also, that something could be done in this direction by careful measurements in the furnace, to be afterwards recorded for comparison on drawings. The figures shown herewith have been prepared from such measurements, and nearly all of them refer to Glendon, where the fuel used was anthracite and the ore-mixture about threequarters of New Jersey magnetic ores and one-quarter of brown-ores from the vicinity of the works. Every occasion furnished by the blowing-in of furnaces was utilized, but the data accumulated rather slowly in this way; and, opportunity oEering to make special trials at no great expense, the figures from 2 to 7 were thus obtained. The trials were made by dumping a hopperful (6 barrows) of material at once into the furnace, and, when all the fuel of a round (12 barrows) had been put in, the profile of the upper surface was obtained by stretching a steel tape across the top on a diameter and at a known height. By measuring down from this with a graduated rod, the profile was easily obtained with sufficient accuracy, especial pains being taken to get correctly the crests of the ridges and the bottoms of the hollows, as many intermediate points being included as seemed necessary. This was repeated on another diameter when there was occasion. The same course was followed for the limestone and ore.

Jan 1, 1899

By C. H. Mathewson

EXCEPTING the joint sessions on gases in metals held during the day on Tuesday, the Institute of .Metals opened its activities with a division dinner at the Commodore on Tuesday evening, with Sam Tour, retiring chairman, presiding. W. M. Corse, secretary-treasurer, outlined the financial status of the division and stated the investment fund is becoming large enough so that in the near future it will be possible to pay all expenses of a foreign lecturer once in two years and not rely on an extended speaking tour to cover expenses. W. B. Price reported on his attendance at the Zurich, Switzerland, meeting of the International Society of Testing Materials and gave a graphic account of his visit to the Grand Salon, his meeting with Mussolini, and his audience with the Pope. Buffalo was announced as the place of the fall meeting, to be held during the week of Oct. 3.

Jan 1, 1932

By R. L. Bowron

GROWING use of basic slag in the agricultural industry is of special interest and importance to the iron and steel industry of the Birmingham district, providing an increasing outlet for this by- product. Such use of basic slag was first developed in England about fifty years ago where it soon became wide- spread. About twenty years ago the Tennessee Coal, Iron & R. R. Co. began its production in the United States after exhaustive tests had demonstrated its high value here as in Eng- land. It is particularly valuable on heavy clay and acid soils, improving their physical condition, increasing their alkalinity where that is desirable, and providing soluble phosphate and small amounts of manganese to soils deficient in these respects. Its use in agriculture is growing as its advantages are becoming more widely known.

Jan 1, 1937

Prof. J. C. BRanner, Stanford University, Cal. (communication to the Secretary): On p. 398, Mr. Hedburg mentions Marionite and Brannerite as ores of zinc. Neither of these has been authoritatively recognized as a distinct mineral species. Marionite, originally described by Elderhorst, was subsequently determined to be nothing else than hydrozincite. Analyses of the so-called Brannerite were sent by me to Prof. Penfield, who says it is a mixture of Smithsonite with some other mineral. On p. 398, Mr. Hedburg says the zinc-bearing formation of North Arkansas " is recognized as the Upper Silurian." So far as my observation goes, the ores occur both in Lower Carboniferous and in Ordovician or Lower Silurian rocks, but nowhere in rocks known to be of Upper Silurian age. If Mr. Hedburg has any paleontological evidence of the Upper Silurian age of these rocks, or of any of them, he will confer a favor upon geologists by making it known. On the same page is another statement in which I cannot concur. He says that in this region, " it can easily be seen that the largest fissure-deposits have been eroded and washed away, leaving here and there a few patches adhering to the hillsides." I am compelled to say that in many years' study of the geology of the region in question, I have never been able to recognize such a state of affairs as Mr. Hedburg here describes. The patches which he regards as remnants of fissure-veins, " adhering to the hillsides," I have found to be either the edges of bedded deposits, or portions of the zinc-bearing breccias, formed along old drainage-lines, and laid bare by the ordinary processes of erosion. That fissure-deposits have been partly removed by the same agency, goes without saying; but it is, in ,my judgment, no more true of North Arkansas than of any other mining-region that erosion has selected and washed away " the largest " deposits. My own views of the region in question are given in detail

Jan 1, 1902

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969

By Walter Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. CASE I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected.

Jan 1, 1937

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By Eugene Guccione

Before answering the question raised in the title, let's briefly consider how East-West trade is viewed within the entire US political spectrum. Essentially, there are four major schools of thought: (1) The Peaceful-Coexistence School. Advocates of this school call themselves free-traders and hold to the premise that: (a) trade benefits all parties involved, hence it is the best tool to achieve peace; (b) US trade barriers should be removed, and the quicker the better; and (c) negotiations, cultural exchanges, and political compromise should be used extensively.

Jan 9, 1974

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By M. Prats, D. G. Russell

The performance of a well in a bounded, layered reservoir with interlayer crossflow has been investigated mathematically. The system studied comprises a centrally located well in a bounded cylindrical reservoir composed of two layers of contrasting physical properties. The reservoir contains a single fluid of small and constant compressibility. In the case of a well producing at constant pressure, the production rate of the crossflow system declines exponentially after the early transient behavior dies out. For wells which produce with constant rate, the pressure-time relationship is linear following the transient. For very early production time, the production rate of the two-layer crossflow system behaves as that of the two-layer stratified system (the case in which the layers are in communication at the well only). Except for early time, in most practical cases the performance of a two-layer reservoir with cross-flow can be duplicated by that of a single-layer reservoir. The equivalent single-layer reservoir must have the same pore volume and the same drainage and wellbore radii as in the two-layer case. In addition, the equivalent reservoir must have a "kh" (permeability x thickness) product equal to the sum of the "kh" products of the respective layers in the crossflow system. If the porosity and permeability distributions are known, the production and pressure behavior of a well with and without crossflow can be predicted. From a comparison of the observed pressure or production performance of a well and the theoretical behavior, the occurrence of interlayer crossflow can be detected. INTRODUCTION When flow is possible across the bedding plane from a low-permeability layer into an adjacent layer of moderate or high permeability, the earlier depletion of the more permeable layer will cause such flow to occur. If this situation exists, the oil recovery from tight layers can be appreciable; thus, the economic ramifications of interlayer crossflow are apparent. The possible importance and extent of flow between adjacent and connected layers — whether resulting from capillary, gravitational, or viscous forces — have been the subject of considerable speculation for many years. Jacquard1 presented a rigorous analysis of the crossflow due to single-fluid expansion occurring between two adjacent and connected layers when the well produces at constant rate. His presentation was entirely mathematical, however, and no numerical results from evaluation of the mathematical solutions were presented. Our objectives in the preparation and presentation of the present paper are essentially twofold— (1) to analyze the behavior of a well which produces a single compressible fluid from a bounded, layered reservoir with interlayer crossflow, and (2) to present practical numerical results and simplified formulas to facilitate engineering analysis of reservoirs with crossflow. The constant-terminal-pressure case was analyzed rigorously, whereas the constant-terminal-rate case was treated only for semisteady-state conditions. DESCRIPTION OF THE IDEALIZED TWO-LAYER RESERVOIR The reservoir to be studied is assumed to be bounded and cylindrical in shape, with a completely penetrating well at its center. The reservoir is composed of two adjacent horizontal layers between which fluid is free to flow. Each layer is assumed to be homogeneous, isotropic and completely filled with a fluid of small and constant compressibility. The total thickness of the reservoir is small enough

By Lucius W. Mayer

WHILE the mind of the financier does not normally run along channels similar to those of his technical adviser, engineers, because of their exactness, are ever more called upon to manage affairs where financial matters are involved. It is, true, not a relatively large number have thus far functioned in this capacity. It is also true that the essentially financial mind could not serve in a responsible engineering position; for to be a successful engineer one requires precise thinking, making due allowance for factors of safety. To be a financier seems to require less aptitude for exact thinking than of enthusiasm and confidence in capitalizing prospective possibilities. Both require imagination, the engineer being, more conscious of the limitations of natural conditions. It is to be regretted that the engineer' stands so far aloof from financial matters. Many consider them- selves successful, as did Steinmetz, as long as their reward is the consciousness that they are giving supreme service to mankind. They are 'generally happy in their work and, like our honored brothers who are teachers, gain their greatest satisfaction, not in the amount of their remuneration so much as in the service rendered society and in the excellence of results achieved. Indeed, these sentiments bespeak character and command respect.

Jan 1, 1924

By Frank H. Skelding

Still the world's largest producer, consumer and importer/exporter of minerals, the United States has, in recent years, become more and more aware of the many diverse forces that increasingly affect its ability to maintain free access to and trade in minerals, both domestically and abroad. The nation's growing dependence upon foreign sources of minerals in the face of mounting competition is causing many changes, not only in the mineral industries, but in national attitudes and policies as well. This paper examines the position of the United States in the world mineral economy relative to the significant trends that have and are developing. It attempts to define and evaluate the major present and future impact of these trends and to anticipate the probable effects upon the U.S. and its mineral economy.

Jan 1, 1976

By Anthony Lucas

THE discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has grown with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover, despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting, and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable

Jan 7, 1918

By Albert Sauveur

(New York Meeting, February, 1913.) IT is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.1 The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance.

Jan 3, 1913

By Oscar H. Hershey

COMPLAINT has been made that in the literature of economic geology the work of the "company or practical" mining geologists does not get enough attention. I propose to attempt to overcome this com¬plaint in reference to one important lead-mining district, that of the Coeur d'Alene in northern Idaho. Furthermore, I will assume that the reader is not so much interested in the geology of the district as in the methods of application used and incidents that have arisen in the work. All the important discoveries of ore in the Coeur d'Alene were made without benefit of geology. Certainly I would not claim the reputed discoverer of the Bunker Hill mine as a fellow geologist. It appears also that the mines were operated quite successfully for many years without geological specialists, though doubtless certain properties were visited at long intervals by such men as Waldemar Lindgren. It was known that the ores occur in quartzite, graywackes and slates as stated by J. R. Finlay in 1903. (TRANS., VOL. 33.) He described the ore as occurring in typical fissure veins that occupy fault-planes of indeterminate displacement. The Bunker Hill lode was based on a definite fissure with the mineralization all on the hanging-wall side, extending as far as 300 ft. from the fissure.

Jan 1, 1933

By A. L. Sweetser

EXPERIENCE has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorination-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave : Fe2O3, 3.35; FeS, 1.5; MnO2, 0.75; ZnCO3, 4; Al2O3, 3.20; H2O, 0.7; SiO2 and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, .and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size-a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Sep 1, 1907

By Louis D. Huntoon

(New Haven Meeting, February, 1909.) THE Hammond Mining and Metallurgical Laboratory is the gift of Prof. John Hays Hammond to the Sheffield Scientific School of Yale University. Professor Hammond was graduated from this school in the class of 1876, and has always shown great interest in its welfare and progress. In 1903, he offered to build and equip for it a mining and metallurgical laboratory. This offer was gratefully accepted by the trustees; and in October of the same year the architect, W. Gedney Beatty, and the writer were employed to draw up plans for the building, which is the largest of its kind in this country. The Treasurer's report shows the total gift of Professor Hammond, including land, building, and equipment, to have been $128,741.53. This does not include $5,000 given by Professor Hammond to defray incidental expenses. The detailed cost of the machinery and installation, included in the above sum, is as follows: Machinery, $9,846.00 Pipe and fittings, 925.05 Hangers, shafting, pulleys, belts, etc., . 357.83 Steel-work, tanks, launders, etc., . 272.19 Screens for sizing ore, 411.37 Lumber, 1,896.36 General Supplies Hardware, . $135.96 Tools, 263.66 Paints, . 04.63 Electric and incidental, . 439.57 - 1,043.82 Machine-shop material, 259.44 Labor, 722.29 - 981.73

Mar 1, 1909

The finding of gold, in enriching quantity, along the streams that issued from the western foothills of the Sierra Nevada was the prelude not only to the birth of an organized mining industry in California but to the intensive exploration of the entire Pacific slope; it presaged the feverish exploitation of the mineral resources that the ubiquitous prospector soon uncovered all over our western domain. At first when this migration began, as typified by the rush of 1849, there was no time to examine the signs of ore that were to be detected along the track of adventure, and, it must be added, not many in that motley crowd of gold-seekers were qualified to interpret the signs if they had lingered to look at them. Such intelligent curiosity as a few of them possessed was directed to the finding of gold chiefly, if not exclusively; and their good sense in this respect can not be impugned, because in a new and remote country the less valuable metals and minerals are unlikely to be worth the winning. Many of those that came to California crossed the alkaline wastes and sagebrush prairies that extend between the Great Sal? Lake and the ramparts of the snow-clad Sierra; when coming overland they found it convenient to halt on the eastern slope and to pitch their camp in the valley of the Car- son river before they began the tedious ascent of the mountains and the final entry into the land of gold. One of the trails most used by these immigrants followed the Carson river to the mountain meadows south of Lake Tahoe and then descended among the pine-woods of Placerville, where they went to work with pan and shovel in the gold-bearing streams

Jan 1, 1932