Search Documents

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

A Discussion of the papers of James Gayley, on "The Application of Dry-Air Blast to the Manufacture of Iron" (see Trans., XXXV., 746, 1022, also pp. 315 and 745 of the present volume, and of J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," p. 454. Chas. B. Dudley, Altoona, Pa.:—I am not a blast-furnace man, and this always puts me at a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, a I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of mater-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 1885, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are, for the moment, interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satisfactory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much easier way, simply saturate the air at a constant temperature, and thus get uniform working and

Jan 1, 1906

By Donald H. McLaughlin

ZEST in the search for new supplies of metallic ores and petroleum is difficult to maintain with stocks of raw materials accumulating and with over- production rightly or wrongly blamed for most of our industrial troubles. Enthusiasm over new methods of prospecting has consequently diminished and exploration programs in many fields have been drastically cur- tailed. Very naturally the effects have been felt with particular keeness in highly specialized phases of the work, such as geophysical prospecting, for the feverish scramble for new areas in which to drill beneath magnetic or electrical anomalies has abated, and there is even a lull in the firing in the battle over salt domes on the Gulf Coast. It is unquestionably an unhappy time for many of the organizations dependent on this work, but in certain respects the situation may be beneficial in correcting unsound practices that .have grown up through the necessity for haste and for quick decisions. With the restriction of the field to the more competent workers by the harsh rule of survival of the fittest, a general improvement, not only in technique but in business methods, can be expected which may go far in restoring public confidence. Geophysical prospecting in the short period that it has been utilized in North America, has suffered severely both from over-popularity and from excessive abuse. The former evil now

Jan 1, 1931

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By Mark L. Requa

(San Francisco fleeting, October, 1911.) DURING the past two years California has developed a new and important oil-field : I refer to Midway. This field produced the famous Lake View gusher, which is credited with a total production in excess of 8,000,000 barrels. Fortunately for the oil industry of the State, this well is now a thing of the past, and nothing save a great crater-like opening marks its location. The pipe is entirely worn away and gone ; and it is a matter of serious doubt if there can be anything done that will cause the well to produce again. Fortunately, also, there have been no, other wells in that field or elsewhere throughout the State that in any way compared with the Lake View. Midway is noted for large wells, of from 500 to 2,000 barrels production; but the decline is rapid, and a few months serve to bring the output down to a few hundred barrels. In the oil-territory heretofore blocked out as proved and probable, there have been, during the year, many changes. Some areas which were expected to be fairly productive have apparently failed; others, more strictly "wild-cat," have come in; while in some of the older fields there are properties which are beginning to show evident signs of exhaustion. The total area of proved territory will therefore probably suffer but small increase, when balances are struck off. The increase of new area has come from extensions of the Midway field, the development of a field in Lost Hills and Belridge, and extensions of the Fullerton-Whittier field in southern California. In these later developments, down to date, the fresh area absolutely proved is not much in excess of 3,000 acres. Recent developments in Coalinga indicate the possible extension of that field to the south, but at great depth. Coalinga is still the most northerly field of any consequence in the State. The Kettleman Hills have hitherto brought in nothing, although a

Apr 1, 1912

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H20, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H20, FeO¬Fe-CO-C02 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky' made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans's solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

Note Any member who desires to be designated as being "Available for Consulting Work" can arrange it simply by sending a written request to the office of the Secretary of the Institute The following list of members is primarily arranged geographically, with secondary consideration to political subdivisions arranged alphabetically First, the states of the United States , then other North America, in order Alaska, Canada, Mexico, the West Indies, and Central America Then cones South America, Europe, Africa, and Asia, each including the near by islands associated with those continents Australia, the islands to the north, and the Pacific islands except Japan are grouped together under Oceania The various countries are indexed on the preceding page NORTH AMERICA UNITED STATES ALABAMA America -Dyar, G C Anniston -DePriest, S H Klugh, B G Lefforge, J W Auburn Poor, R S Bankhead -Armstrong, W D Bessemer -Beck, A IV, Jr Carnes, D Chabot, L S , Jr Creveling, J C

Jan 1, 1952

By R. E. Zimmerman, Michael Sokaski, E. R. Palowitch, M. R. Geer, H. F. Yancey, W. Deurbrouck, S. C. Sun

PART 1: DENSE MEDIUM SEPARATION by M. SOKASKI, M. R. GEER and H. F. YANCEY INTRODUCTION In the early days of coarse-coal treatment by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken :he loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War 11 in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-ton-per-hour pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London. In April 1945,2 operation of this pilot plant was observed by one of the authors, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was started by the Bureau of Mines immediately. This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals was made available. Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are so easy to clean they respond well to simpler cleaning systems, the first cyclone plant was not built until 1961.3 As of the spring of 1967, a total of 31 commercial cy- clone plants had been installed or were under construction in the United States; this does not include eight Dynawhirlpool plants. The capacity of the cyclone plants ranges from 50 to 1300 tons per hour and totals 6600. THEORY Before discussing the theory of a dense medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in figure 10-1, the mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vertical flow. The refuse moves along the wall of the cyclone and is discharged through the under- flow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the vortex finder to the overflow chamber.

Jan 1, 1968

After months of negotiations, the U. S. has agreed to buy between 6000 and 7000 long tons of Bolivian tin now stockpiled at Peruvian and Chilean ports, at $1.175 per lb, f.o.b. South American Ports. Harry A. McDonald of the Reconstruction Finance Corp. signed the contract with Victor Andrade, Bolivian ambassador. The Mercantile Metals and Ore Corp., of New York City, acted as the agent of Bolivia's Banco Minero in negotiating the deal. The contract is a short term one. Throughout the talks, the U. S. refused to make a long term agreement because of the possibility that Bolivia will soon nationalize its mines. The Bolivians desired to sell the U. S. 18,000 tons during a one-year pact. The price agreed upon is roughly the same as with Malayan producers. In the meantime, American Smelting & Refining Co., signed over control of its operations to the Bolivian Government. The formal act of leasing the mines to the Bolivian Government follows the announcement last July by the company that it was closing operations because of high costs. Contract terms were not disclosed.

Jan 1, 1952

By St. John, JOHN Ancel

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to bean alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated.

Jan 1, 1927

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By Arvid E. Nissen, Knox Taylor, John H. Hall

Some months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter he had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908, and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel. A brief examination of the tests in Table 1 shows that certain treatments of, for instance, 0.30 per cent, carbon steel are not represented by any test data. Had this been a laboratory research, this information would undoubtedly have been furnished, but as this work was done for commercial purposes the omissions are due to the fact that, at the time the work was done, we saw no advantage in trying every composition of steel with each treatment discussed in the paper.

Jan 1, 1920

By J. E. Steiner, J. M. Hodge, M. A. Orehoski

Ingots of four steels (1045, 1080, Ni-Mo-V, and Ni-Cr-Mo-V) were cast at pressures varying from about 1 to 760 mm of mercury, so as to obtain a range of hydrogen contents in each steel. The susceptibility of these steels to flaking was evaluated by cooling hot-rolled blooms at a range of cooling rates, varying from water quenching to slag cooling, and studying the occurrence of flaking as a function of cooling rate. The steels exhibited differences in susceptibility to flaking, and a tlzreshold value for hydrogen content for each steel was found, below which the susceptibility was very low and above which the susceptibility increased markedly with increasing hydrogen content. Mechanical property evaluations, metallogvaplzic exantinations, and X-my diffraction determinations o,t retained austenite were made on samples from the blooms. A mechanism of flaking which is consistent with the observed behaviors, the effects of hvdrogen content, and the differences in susceptibility among the steels investigated is postulated, based on the results of mechanical property evaluations and metallographic and X-ray diffraction studies. ThE important role of hydrogen as a factor in the occurrence of "flakes" or "hair-line cracks" in steel has now been established by many investigations. These have included investigations by steel producers and forging manufacturers, to whom the prevention of flaking is a very real and serious problem, and many research studies aimed primarily at establishing the mechanism of this behavior Several investigators3 have reported that steels cast at reduced pressures (absolute pressures of about 1 mm) not only are low in hydrogen content but are essentially insensitive to the formation of flakes. These investigations have shown that a general relationship exists between hydrogen content and susceptibility to flaking. The difficulty of obtaining suitable samples of steels of a given composition with the desired range of hydrogen contents, particularly in the relatively large sections in which flaking most commonly occurs, has been the principal obstacle to quantitative evaluations of these relationships. Steels with intermediate hydrogen contents between 1 ppm, and the 4ppm or higher of air-cast steels are generally not available in commercially produced steels. Laboratory procedures, in which the hydrogen is introduced into solid steel samples by heating in a hydrogen atmosphere under pressure, generally involve a limitation in the size of the sample which can be treated, and thus are not representative of the behaviors in large sections. The availability of a facility at the South Chicago Works of U.S. Steel, in which several ingots could be cast from a single heat of steel at total air pressures ranging from 0.25 to 760 mm of Hg, has made it possible to overcome this obstacle and to obtain ingots of a given steel covering the intermediate range of hydrogen contents desired. These ingots, furthermore, are of a size suitable for the production of product with section sizes large enough to be representative of the products in which flaking most commonly occurs in commercial production. In these experiments, this facility was used to study the relationships between hydrogen content and the susceptibility to flaking of four steels, two plain carbon steels at 0.45 and 0.80 pct C and two low-carbon alloy steels representing a medium and a rather high hardenability level. These flaking studies were supplemented by evaluations of mechanical properties and by metallographic studies on samples from the blooms, in order to obtain pertinent information on the factors other than hydrogen content which influence the susceptibilities of these steels to flaking. Based on the results of these tests, a mechanism for the initiation and propagation of the flaking cracks, which is consistent with the observed behaviors, is postulated. MATERIALS AND EXPERIMENTAL WORK Steelmaking and Conversion. To provide material for the investigation, five 29- by 35-in., hot-topped, big-end-up ingots were cast from each of four 80-ton, basic electric-furnace heats of four different steels (a 1045 steel, a 1080 steel, a Ni-Mo-V steel, and a Ni-Cr-Mo-V steel). A double-slag practice was used on all steels and the two plain carbon steels were Si-A1 deoxidized with an addition of 2 lb of A1 per ton, while the Ni-Mo-V and Ni-Cr-Mo-V steels were deoxidized only with silicon and

Jan 1, 1964

By E. A. Gulbransen, K. F. Andrew

Thermodynamic information on the solubility of hydrogen in exothermic metals is limited. Thus, the overall solubility decreased as the temperature rose, which suggests the heat of solution of hydrogen in the metal is negative; yet the terminal solubility in the metal phase increased, which suggests an endothermic reaction. A thermodynamic analysis, therefore, was made of the several equilibria involved when hydrogen dissolved in the metal. Equations were derived expressing the solubility, terminal solubility, and decomposition pressures of hydrogen in terms of the heat, entropy, and free energy of solution of hydrogen in the given phase. The relations between the thermodynamic functions for the a-zirconium and 8-hydride phase were developed. The thermodynamic quantities were determined experimentally by the measurement of the decomposition pressures over a broad composition and temperature range. Two new methods of analyzing the experimental data were developed for determination of the terminal solubility. STUDIES', ' of the impact strength of zirconium at room temperature indicated that small quantities of hydrogen, of the order of 10 parts per million, embrittles the metal. Micrographic' and X-ray diffraction' studies showed this embrittlement to result from the precipitation of a second phase upon slow cooling. These studies suggested that the terminal solubility of hydrogen in the metal phase increased with increase of temperature. This behavior appeared to contradict the effect of temperature on exothermic hydrogen occluders such as zirconium. For these metals, the solubility of hydrogen should decrease with increase of temperature. Before these facts could be understood, a thorough analysis of the several equilibria was essential. It was the purpose of this paper to consider the several equilibria involved when hydrogen was reacted with zirconium from both the theoretical and experimental points of view. Since the overall solubility of hydrogen in the metal has been considered by a number of workers, it was proposed to study the composition range 0 to 6 atomic pct H in detail. Literature Schwartz and Mallett' determined the terminal solubilities of hydrogen in the metallic phase from diffusion studies. They extrapolated concentration-penetration curves to the boundary between the solid solution phase and the hydride phase at the surface. Their results showed values of 2.6 atomic pct at 400°C and 5.2 atomic pct at 500°C. Extrapolations of the data to room temperature suggested very low values for the terminal solubilities. This study confirmed the hydrogen embrittlement results and indicated that the terminal solubilities increased as the temperature was raised. The solution of hydrogen in zirconium over the complete concentration range was studied by Hall, Martin, and Rees3 and by others. The results showed that hydrogen was absorbed up to a maximum composition of 66 atomic pct or ZrH This composition represented the t-hydride phase. The maximum amount of hydrogen absorbed increased with pressure and decreased with temperature. Due to this temperature behavior, zirconium was classed as an exothermic occluder." In 1930 Hägg studied the crystal structures of the Zr-H alloys over a broad composition range. Four hydride phases were found. However, the range of homogeneity of the several phases was not studied. Gulbransen and Andrew" recently studied the phase diagram of this system by X-ray diffraction methods and by a thermodynamic method based on decomposition pressure measurements. The results showed that only two hydride phases existed for low temperatures, the 6 and the .-phases of Hagg.' Both phases had broad regions of homogeneity. The lower limit of the two-phase region of a and d-phases suggested a terminal solubility of 4 atomic pct at 500°C. This value was in agreement with the results of Schwartz and Mallett.' To avoid hydrogen embrittlement at low temperatures, it was necessary to heat the metal in high vacuum at elevated temperatures. To choose the conditions of temperature and high vacuum, it was

Jan 1, 1956

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go-into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as-nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical, specifications, color demands must also be met. The firm of which I have the most, knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By Utley Wedge

(Cleveland :Meeting, October, 1012.) In general, the art of securing copper from sulphide ores or concentrates may be said to consist of : (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a preliminary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a * Presented also at the Joint Meeting of the Institute and Section IIIa, Metallurgy and Mining, of the Eighth International Congress or Applied Chemistry, New York, N. Y., September, 1912, and here published by mutual agreement.

Dec 1, 1912

By A. A. Blow

The productive area of the Leadville mining district immediately adjoining the city of Leadville, which, by its wonderful richness, has attracted the attention of the mining world for the past twelve years, may, with a few exceptions, he considered as divided into seven local mining centers, separated one from another by the topographical features of the country, and designated by common consent as Fryer Hill, Yankee Hill, Breece Hill, Rock Mill, Printer-Boy Hill, Iron Hill, and Carbonate Hill. Of these seven distinot mining localities, or groups of mines, the central one, Iron Hill, is the one of greatest importance and interest. It was the scene of the earliest discovery of carbonates, as far back as 1875, and since that time has always maintained its position

Jan 1, 1890