Search Documents

By Wolfgang Pietsch

Direct Reduced Iron is a product obtained during solid state reduction of iron oxides into metallic iron. General chemical and physical characteristics of all direct reduced iron materials result in a noticeable reoxidation tendency and a relatively low ignition temperature. As most of the chemical reactions are exothermic, normally heating occurs and if water is present hydrogen evolves. Dry direct reduced iron deactivates quickly in air but is still reactive if it comes into contact with moisture. Because of these characteristics, special requirements are necessary for safe storage, shipment, and handling. In an effort to improve this situation passivation techniques were and still are being developed. The paper discusses the properties of direct reduced iron, presents past experience with storage, shipment, and handling of MIDREX® Iron, a direct reduced iron material produced in the MIDREX® Direct Reduction Process, and evaluates benefits derived from different passivation techniques.

Jan 1, 1978

Joseph HartshoRnE, Pottstown, Pa.: I have read Professor Akerman's valuable paper with great interest. Few of the present generation of American steel metallurgists are aware of the very important part taken by Swedish engineers in the successful development of the Bessemer proeess, and I am afraid some of the older ones have forgotten it. Certainly, I think, most of us would have said that Terre Noire was the first to introduce the use of metal direct from the blast-furnace. It is very well, therefore, that honor should be given to whom honor is due. I can speak from personal experience upon one part only of Prof. Akerman's paper; namely, the effect of the temperature at which the molten metal is cast upon the quality of the finished steel. In a general way I have, of course, known for a long time that the

Jan 1, 1894

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain Members.

Jan 1, 1946

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type.1 Prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied.

Jan 11, 1979

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

By C. Chiou, M. E. Fine

While Gunier-Preston zones are growing in Al-4.2 pct Cu at room temperature, Young's modulus, measured dynamically, increases about 0.4 pct. From the change in modulus with time the exponent of time in the rate equation for growth of the zones was deduced to be %. From a comparison of the rates of increase of modulus at 1, 28, and 42°C an activation energy of 12 to 14 Kcal per mole is computed. These findings support the idea that copper atoms are supplied along dislocation channels to growing zones. In alloys the elastic constants will be functions of the distributions of the atoms. If the degree of ordering or clustering is changed, one expects a corresponding change in the elastic constants. During age-hardening of aluminum-copper alloys at room temperature, the copper atoms cluster on 100-type planes in the aluminum lattice forming

Jan 1, 1959

Joseph HartshoRnE, Pottstown, Pa.: I have read Professor Akerman's valuable paper with great interest. Few of the present generation of American steel metallurgists are aware of the very important part taken by Swedish engineers in the successful development of the Bessemer proeess, and I am afraid some of the older ones have forgotten it. Certainly, I think, most of us would have said that Terre Noire was the first to introduce the use of metal direct from the blast-furnace. It is very well, therefore, that honor should be given to whom honor is due. I can speak from personal experience upon one part only of Prof. Akerman's paper; namely, the effect of the temperature at which the molten metal is cast upon the quality of the finished steel. In a general way I have, of course, known for a long time that the

Jan 1, 1894

By Robert L. Voss, Richard D. Hagni

Sparry dolomite from all of the operating mines in the Viburnum Trend of Southeast Missouri have been found by cathodoluminescence microscopy to reveal a systematic pattern of banding resulting from a growth zoning within individual dolomite rhombs. Four principal bands have been recognized throughout the entire Trend and each of the major bands contain even finer internal banding. Minor bands a few microns in width can be correlated in specimens collected ten's of kilometers apart along the trend. The first three principal dolomite bands decrease from south to north. This feature, together with the fact that the white sparry dolomite crystals decrease in abundance from south to north in the Trend, suggests that a major source for the fluids was from the south. The application of cathodoluminescence microscopy to crystalline dolomite demonstrates a strong correlation between ore grade and the intensity of internal banding and dissolution textures.

Jan 1, 1985

By Chester A. Rowland, David M. Kjos

Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured non- metallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls. This chapter covers rod and ball mills which utilize manufactured metallic grinding media. Fig. 1 shows the cross section of an overflow rod mill, Fig. 2 an overflow ball mill, and Fig. 3 a diaphragm (grate) discharge ball mill.

Jan 1, 1978

At 8 o'clock on the evening of Thursday, July 25th, the special train chartered by the Provincial Government for the Institute's use, pulled out of Toronto. Ten parlor cars and two dining cars made up the train. The culinary arrangements were under the personal supervision of Mr. McConkey, of Toronto. [ ] The Hon. Frank Cochrane, Minister of Mines, Lands and Forests, was the efficient host of the party. He was assisted by the Hon. Dr. Pyne, Minister of Education, and by Mr. T. W. Gibson and Dr. W. G. Miller. On arriving at Cobalt, the delegates were met by the following Committee Mr. A. A. Cole, representing the T. & N. 0. Railway; Messrs. R. W. Leonard and D. B. Rochester, deputies from the Cobalt Chamber of Mines ; Messrs. Run¬ning and Martin, from the Cobalt City Council; Messrs. McLeod and Ferland,

Jan 1, 1907

By Joseph Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned.

Jan 1, 1929

By Bruce N. McIver, Leo Casagrande

Similarities are noted in the practices and problems of constructing dams to impound mine tailings, fly ash, and chemical wastes. The comparison of a typical tailings dam with a conventional water-retaining earth dam shows that the former is inherently less stable and can be susceptible to cracking, liquefaction, erosion, and frost action, as illustrated by examples. Several methods are presented for building safe tailings dams using either the coarse fraction of the tailings or local soils, the important factor in each method being proper compaction of the material. The safety of existing tailings dams can be improved by flattening the overall slope, preferably by adding berms, or by decreasing the height. Where neither remedy is possible, the installation of electro-osmotic tie-backs is suggested. Dumps of mine spoil can be stabilized economically by compacting the material in layers along the toe to form a dam.

Jan 1, 1971

By George Frederick Kunz

Mexico has been famous for its silver-mines ever since the Spanish conquest; but in respect to gems, although many varieties occur, yet only a few have been obtained in any important amount. Considering the extent of country in Mexico and ill the adjoining States of the Central American Republics, and the richness of mineral wealth that must surely exist there, our present knowledge of the occurrence of precious stones is remarkably small. The great prevalence of igneous rocks would lead us to anticipate the future discovery of many localities of gems and ornamental stones, when fuller scientific exploration shall have taken place.* At the present time the only gem-stone that is systematically mined in Mexico is opal, and the only important ornamental stone is tecali, the so-called Mexican onyx. In addition to these may be mentioned the pink garnet, or rosolite, found in one

Jan 1, 1902

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By D. K. Crampton

THE study of copper alloys of the age-hardening type has received considerable attention, and, among the alloys which the authors have considered, those containing small amounts of nickel and phosphorus as essential constituents seem especially interesting. Such alloys have attractively great capacity for being hardened and also have relatively high electrical and thermal conductivity in the hardened state. In addition, it has been found that the increase in hardness and strength imparted by aging can be greatly augmented by cold-working, so that axcellent combinations of conductivity and strength are obtainable. In view of the possible importance of the alloys, it was considered desirable to investigate the solubility relationships in the copper-rich portion of the copper-nickel-phosphorus system. This paper presents some of the results obtained in this investigation to date and also gives properties of typical alloys that appear to be of commercial interest.

Jan 1, 1940

By M. T. Simnad, C. E. Birchenall, M. H. Davies

THE marker movements observed by Davies, Simnad, and Birchenall during the growth of magnetite on wustite have been misinterpreted. It is the purpose of this note to correct the original interpretation. In that investigation wustite specimens were prepared by oxidizing pure iron disks in water vapor until the iron was consumed. Argon was used as a carrier gas for the water vapor and on the complete conversion of the metal to its oxides ('FeO' plus a small amount (10 pct) of surface Fe3O) the water supply was bypassed and the specimens were annealed in argon alone in order to equilibrate the wustite with the overlying magnetite. After cooling, the magnetite was ground off, a crude magnetic test being employed to determine its complete removal. Radioactive silver streaks were then applied to the surface and the specimen was oxidized completely in water vapor to prevent hematite formation. After complete oxidation the markers were found to enclose about 80 pct of the magnetite with the other 20 pct lying outside the markers. This observation was interpreted to mean that oxygen transport was four times as great as iron transport during the growth of the magnetite. The conclusion would have been correct if, as in the case of wustite growing on iron, all the iron had started from one side of the marker and all the oxygen from the other side initially. Actually a material balance is required. For simplicity, take wustite to be exactly FeO, and magnetite to be Fe3O,. Then at the start of the reaction 3 FeO + O -> Fe,O., All of the iron and three-fourths of the oxygen of the final product will be within the marker inter- faces. The other fourth of the oxygen is in the gas phase outside the marker. From the experimentally determined final position of the markers simple calculation shows that one-fifth of the total iron has crossed the marker interface, while one-twentieth of the total oxygen has crossed in the reverse direction. The simplified result favors iron transport in the ratio four to one. However wiistite is not stoichiometric FeO. At 900°C, the temperature of the measurement, the composition is about FeO When the material balance for the same experimental result is repeated, assuming the product will be 1 mol of Fe3O4, it is found that 0.6 gram atoms of iron and 0.19 gram atoms of oxygen must have passed the marker in the same direction. (This is readily apparent from the reaction to form 1 mol of Fe3O4 SFeO The total oxygen supplied from the atmosphere is 0.61 gram atoms, but the iron which passes the marker interface, i.e., 0.6 gram atoms, requires 0.8 gram atoms of oxygen to convert it to Fe,O,.) If all the transport during magnetite growth is due to iron ion diffusion, then the marker would enclose about 85 pct of the final magnetite and the original measurement is in error by about 5 pct. This error is probably less than the uncertainty in locating the markers by autoradiography. The possibility also exists that the starting wustite was not quite saturated with oxygen and underwent further enrichment with consequent envelopment of the marker before magnetite caught up with the marker interface. In any case it appears that these measurements actually favor iron ion diffusion in magnetite overwhelmingly as the factor controlling its growth, although further experimental measurements are needed to eliminate the error in material balance described. Such studies are planned.

Jan 1, 1954

By Ed L. Reed

INTRODUCTION The most efficient development of a mine plan for in-situ leach (solution) mining must be based upon an understanding and application of the basic hydrologic characteristics of the aquifer containing the mineral values. Similar knowledge of the overlying and underlying aquifers is also required. This paper summarizes the hydrologic properties of a ground water system and describes some of the more important conclusions that can be drawn from a detailed hydrologic study. Basic to an in-situ leach mining operation is the flow of fluids through porous rock from place to place. The degree to which these movements of fluids can be predicted and controlled determines to a large extent the efficiency of the ore recovery operation. HYDROLOGIC CHARACTERISTICS The principal hydrologic characteristics of a porous medium (sand, intercrystalline or vuggy limestone, fractured basalt, etc.) influencing fluid flow are: Porosity Permeability Thickness Transmissivity Storage Coefficient Water Table or Piezometric Surface Hydraulic Gradient Briefly these parameters can be defined as follows: Porosity: the void space in a unit volume of rock. Permeability: the ease with which fluid will flow through a porous medium. Thickness: the height of the formation which contributes flow to a well. Transmissivity the product of permeability and thickness. Storage Coefficient. the volume of water released from the reservoir per unit drop in head. Water Table or Piezometric Surface: the level at which water will stand in a well: the top of the zone of saturation in a gravity aquifer; the height to which water will rise above the confining bed in an artesian system. Hydraulic Gradient the direction and rate of dip of the water table or piezometric surface. A properly designed pumping test will provide numbers for transmissivity, storage coefficient and the water table or piezometric surface. Drilling records or bore hole logs provide aquifer thickness data from which permeability can be calculated. Ground elevations applied to measured depths to water enable one to calculate the direction and rate of dip of the water table or piezometric surface. Porosity can be determined from core analyses or density logs; it can be estimated from grain size distribution curves in sands or sandstones and from, microscopic examination of drill cuttings derived from carbonate aquifers. CHARACTERISTICS OF FLUID FLOW The characteristics of fluid flow that are vital to an understanding of leach mining include: Velocity Direction Flow Path Radius of Influence The velocity of fluid flow is of paramount importance in planning and managing a leach mine operation. Velocity is directly proportional to the permeability and hydraulic gradient and indirectly proportional to the effective porosity The permeability determined from a pumping test is an average value for the interval stressed; therefore, the velocity calculated from data derived from a pumping test represents average conditions. Under actual conditions discrete portions of the aquifer open to the screen may have permeabilities several times as high as the average and minimum permeabilities only a fraction as much. An injection front will be irregular to the extent that the reservoir rocks are heterogeneous An important consideration is the direct relationship of velocity to head. A reservoir which would provide a velocity of 0.05 feet per day under conditions of equilibrium would allow fluid flow of 36 feet per day under typical leaching operations, i.e. 12-foot injection head, 12-foot pumping level and 50 foot five-spot pattern. The direction of fluid flow is also vital both inside and outside the mine area. In the pattern area the direction of flow is determined by the geometry of the well field and can be approximated by mathematical modeling techniques. Outside the well field, the direction of flow is influenced by both natural conditions and the degree to which production and injection volumes are balanced. Flow directions (and velocities) are critical to an understanding of leachate excursions and their control.

Jan 1, 1979

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

By C. R. Simcoe, T. J. Koppenaal

The effect of direct and alternating currents on the quench aging behavior in an Al-4 pct Cu alloy has been investigated by use of resistivity measurements. The reaction rate increases with direct current density in the investigated range of 1000 to 3000 amps per sq cm. Alternating current of a specific frequency is observed to decrease the reaction rate by a factor of about two. ErDMANN-JESNITZER et al.,1,2 investigated the effect of direct and alternating current on the quench and strain aging behavior of low-carbon iron. In both cases they observed that direct current accelerates the aging reaction and that an alternating current can completely inhibit the aging process. The purpose of the present research was to investigate these phenomena in the quench aging behavior of an Al-4 pct Cu alloy and to determine the correlation, if any, between the increase in the observed reaction rate and possible heating effects accompanying the aging with direct current. EXPERIMENTAL PROCEDURE The aluminum-base alloy used in this investigation contained 3.98 wt pct Cu (1.72 at. pct) with impurities of 0.003 pct Si, 0.002 pct Fe, and 0.001 pct Mg. The alloy was rolled into a ribbon about 0.36 mm thick and 3.7 mm wide. The ribbon was split end from end with the ends being used as electrical contacts and the central unsplit section, about 5.3 cm in length, serving as the specimen. Solution treatment was accomplished by quenching from a salt bath at 520° ± 2°C into water at 25° ±0.5°C; the specimen was immediately transferred to a liquid nitrogen bath. All aging was done at 75° ± 0.2°C in a rapidly stirred ethylene glycol bath. Resistivity measurements were made by the double potentio-metric method employing a standard resistor; for purposes of convenience, the resistance measurements were made at 77°K. The transfer of the specimen from the aging bath to a liquid nitrogen dewar was accomplished in less than 1 sec. The aging kinteics were studied with the specimen being aged under the influence of direct current, alternating current, and without any type of current. The amount of heating caused by direct currents was investigated by soldering a thermocouple on the specimen surface and measuring the temperature change after applying various current densities. The temperature was observed to increase (from 75°C, the aging temperature) about 0.8°, 3.0°, and 8.5°C with direct currents of 1000, 2000, and 3000 amp per sq cm, respectively. When employing alternating current, the circuit was monitored with an oscilloscope and adjustments made to produce a normal sine-wave pattern. RESULTS Prior investigations3&apos;4 in the aging characteristics of A1-4 wt pct Cu have shown that the resistivity initially increases, reaches a maximum, and then decreases to values significantly lower than the as-quenched resistivity. This type of behavior is seen in Fig. 1 which shows the resistivity at 77°K as a function of aging time at 75°C observed in this investigation. At this aging temperature, the resistivity maximum is seen to occur in about 1 to 1-1/2 min and it further decreases to the as-quenched value in about 24 min. The behavior observed with the application of direct currents of 1000, 2000, and 3000 amp per sq cm during aging is shown in Fig. 2. With increasing current densities, (+) ?pmax decreases and the rate of the aging process increases. The time necessary to reach the as-quenched resistivity value decreases from 24 min for aging without current to about 16, 10, and 7 min for aging with 1000, 2000, and 3000 amp per sq cm direct current, respectively. Fig. 3 shows the results obtained when two changes were made during the aging with 2000 amp per sq cm

Jan 1, 1963

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;&apos; the direction and the driving force of grain boundary sliding and migration;&apos; the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.&apos; It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954