Search Documents

By A. Gatti

A dispersion of AI2O3 was produced within chromium by the hydrogen reduction of a solid solution of Cr2U3-A1203. The yesulting powder. was compacted, extruded, and the material tested in tension at various temperatures and in creep at 1800°F. The material is ductile above 1200°F and is at least twice as strong as electrolytic chvomium at all temperatures. Its creep resistance, rupture strength, and ductility at 1800°F warrant further work to improve its Low -temperatutre properties. BECAUSE of its high melting point and excellent corrosion resistance, chromium has long been considered as a base for high-temperature alloys. Most chromium base alloys, however, are extremely brittle at low temperatures. Elements such as nickel and iron lower the melting point of chromium and thereby limit its high-temperature usefulness. Chromium-alumina materials made by othersl, 2 have shown good high-temperature creep resistance but poor ductility and thermal shock resistance. Pure ductile chromium3 is weak at high temperatures and reverts to a brittle state if exposed to nitrogenous atmospheres. In sintered aluminum powder (SAP)4 and internally oxidized alloys of silver, copper, and nickel, fine dispersions of oxide phases can control hardness, recrystallization, and yield stress. The possibility of formation of a ductile, high-strength material by precipitating dispersions of alumina in a chromium matrix appears worthy of investigation. MATERIAL Powder Production—Chromium oxide and alumina in amounts to produce a final alloy of Cr + 16 pct AI2O3 by weight were colloid milled, filtered, dried and high fired for 16 hr at 1600°C in air. The resulting solid solution of oxides was ball-milled to a fine powder and the chromium oxide reduced to chromium by heating in pure dry hydrogen for 64 hr at 1400°C. Final Materials Produced by Powder Metallurgy Techniques—-Chromium powder, containing a disper-sion of alumina, was pressed into 1 1/8-in. diam slugs at 25 tons per sq in. and sintered 16 hr at 1400° C in pure dry hydrogen. The sintered slugs were encased in a stainless steel can, 2 in. in diam, and extruded at 1200° C through a 1/2-in. die. The 16 to 1 extrusion ratio produced a final chromium-alumina rod 1/4 in. in diam about 30 in. long. Samples of the rod were plunge-ground to small rupture bars of 0.82-in. gage length with a 0.01-sq-in. cross section. RESULTS Microstructure Studies—Fig. 1 is the microstruc-ture of the material in the as-sintered condition while Fig. 2 is the microstructure of the material as-extruded. Comparison of the as-sintered and as-extruded micrographs show the redistribution and realignment of the alumina inclusions by the extrusion

Jan 1, 1961

By L. Grånäs, B. Aronsson

In a recent study of Fe-Si alloys Walter and Koch' observed pairs of dislocations in Fe-6.25 pct Si crystals rolled to reductions of 10 pct and subsequently annealed for 1 hr at 650°C. They interpreted these pairs as being due to stacking faults. From the spacing of the dislocations a stacking-fault energy of 15 to 19 ergs per sq cm was calculated. These authors did not pay any attention to the order -disorder phenomena in Fe-Si alloys. It is the purpose of this communication to report some preliminary results from a study of ordering and its influence on the plastic deformation of Fe-6.0 pct Si alloys. Our results suggest that the dislocation pairs observed by Walter and Koch may have been due to long-range order rather than to stacking faults. The alloys used in this investigation were prepared from pure electrolytic iron and silicon and were melted in argon. After hot working, strip tensile specimens were machined to a gage length of 70 mm and a thickness of 1 mm. The specimens were heat- treated for 2 hr at 1000°C, furnace-cooled, and subsequently deformed 2 pct in tension at 400°C. The strain rate was 5.6 X lo-' sec-'. Thin foils of the deformed specimens were prepared by means of the Bollman technique and examined in a Siemens Elmis-kop I at an accelerating voltage of 100 kv. In the Fe-Si system long-range ordering occurs at a silicon content of about 6 pct Si. In our alloys evidence for ordering is given by selected-area diffraction patterns which show extra reflections consistent with a super lattice of the D0 9 type. In addition, the dislocation arrangement in deformed specimens indicates that long-range order is present. A typical mi-crophotograph of a thin foil is shown in Fig. l. The dislocations are usually straight and parallel and laying in distinct directions. In the commonly observed (111) zone the projections of the dislocations are close to (113) and (oil). Observation of the image position indicates that the two dislocations in a pair have the same Burgers vector and hence constitute a superlattice dislocation.~ According to theory3 a superlattice dislocation in the DO3 structure consists of four ordinary dislocations connected by two types of antiphase boundaries as shown in Fig. 2. In our specimens only two dislocations in each pair have been observed, Fig. 1. The problem is to decide whether the area between these is a NN or a NNN antiphase boundary. Dark-field images using the (200) reflexion (the indices are defined with respect to the DO3-type superlattice) can

Jan 1, 1968

Manganese Resources in Relation to Domestic Consumption Discussion of paper by JOHN V. W. REYNDERS, presented at the Cleveland Meeting and issued, as Pamphlet No. 1656-C, with MINING AND METALLURGY, May, 1927. A. G. BETTS, Kinderhook, N. Y. (written discussion).-When a business concern hires an office boy, it takes on the first bright-appearing young chap to apply and pays him the prevailing rate of wages. One of the chief tasks the .office boy is supposed to be competent to perform, is to clean out the office. The manager of the business is highly competent in many lines, but for some reason lacks the ability to keep the office clean. To the steel man, it would seem that manganese is the office boy, and it is purchased just as found and offered to the purchasing agent. The steel mill is competent to perform many functions on a grand scale and with wonderful efficiency, but it is unable to make real steel. It is the function of the office boy, manganese, to do this. It is open to serious doubt if steel mill operators have ever taken seriously the metallurgy of the preparation of crude manganese. It has merely been found that some usable crude manganese may be obtained by running certain manganese ores through an iron furnace when not busy on anything else, or remote from iron ore, or with a lining that is about gone. It is, however, an entirely unwarranted assumption that the metallurgy of manganese has been worked out, or that the supplies of usable raw ore must be limited to materials of some specified analysis. There was a time when ores of copper, lead and zinc, for example, had to be rich and of specified analysis, to be usable, but the commercial raw materials of today bear little resemblance to such ores of the past. The discussions of manganese that I have seen are based on the assumption that the metallurgy of manganese is fully established and that the only usable manganese raw materials are of the kind used today. These discussions contain another error, not so much of statement, but of implication-that the tonnages of manganese materials in the United States are so much in this state and so much in that. When it requires a period of years and the expenditure of millions of dollars for a competent mining company to explore thoroughly a few acres of mining ground, is it not absurd to say that there are so many hundred tons of manganese ore in a certain state? This fact is not apt to be known fully in 10,000, years. I do not charge the mining engineers. who are on record, of making misstatements, because they merely say that so much

Jan 5, 1927

By R. E. Reed, C. J. McHargue

Poly crystalline aluminum specimens having random and diffuse (001) initial orientations were reduced 90 pct in area at room temperature by drawing, extruding, and swaging. Although each procedure produced the duplex (001)- (111) texture, there were marked dqferences in the relative amounts of each component. This also produced variations in the tensile properties of the aluminum rods. It is generally agreed that the fiber texture found in aluminum rods consists of a strong (111) and a weak (001) component after reductions in area of 90 pct or more. An examination of data summarized in recent reviews'-3 shows much spread in the values for the relative amounts of the two components reported by different investigators. That the initial orientation has a marked influence on the final texture even after reductions in area greater than 90 pct is well-documented.4-7 Another factor which may influence the relative amounts of the two components is the method of fabricating the wires or rods. Barrett and ~assalski' state that the center of wires formed by rolling, swaging, and drawing have the same textures. The data cited in support of this conclusion came from qualitative X-ray techniques. In recent years there has been renewed interest in correlating the type of preferred orientation with such parameters as stacking fault energy and onset of mechanical twinning.'' Since these analyses have often used many sources of data, it is essential that the data be evaluated for the effect of fabrication variables. In this study we have produced aluminum rods by drawing, swaging, and extruding and have quantitatively determined their textures. All specimens had the same purity and fabrication temperature, and the amount of deformation and the starting textures were determined. We have compared our results with published studies on similar materials and fabricating parameters. We have also compared results from the same three fabricating procedures for single-crystal specimens in three instances. EXPERIMENTAL PROCEDURE The aluminum was 99.99+ pct with the only detected impurities being (by weight) 0.002 pct Cu, 0.001 pct Si, and 0.001 pct Mg. Cylinders a in. in diam by 1 in. long with a fine-grain random texture were made by the following method. Cubes 1+ in. on a side were machined from 2-in.-diam ingots. These cubes were slowly pressed about 30 pct in each of the cube directions. The material was recrystallized by annealing 1 hr at 350°C. Three deformation-anneal cycles produced the desired material. Polycrystalline specimens with a diffuse (001) texture were made by casting into a graphite tube 1 in. ID, li in. OD, by 8 in. long which had been preheated to 900°C. One end of the tube was placed on a water-

Jan 1, 1969

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly 100 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposition is accompanied by a change in volume of as much as 5 per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson' found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter5 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to 90 per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced 90 per cent when forged to ½ -in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By Robert M. Dreyer

Diamond is the hardest known material. The diamond industry is separated into two major segments: (1) industrial and (2) gem. The major industrial use of diamonds is as a high-grade abrasive in a wide variety of applications for which no effective low-cost substitute is available. Table 15.4C.1 gives data on diamond production and on United States diamond imports. In both gem and industrial diamond production, but especially in the case of gems, the quantity of stones produced is not directly correlated to value, for the determination of value is markedly affected by quality. South Africa long has been the world leader in gem diamond production with an estimated production in 1968 (including South-West Africa) of about 4 million carats, equal to 43% of world production. During the past decade there has been a marked rise in gem diamond production in the USSR, so that nation is now the second-ranking world producer, with Angola (Portuguese West Africa) third. In natural industrial diamonds, the major production comes from Congo-Kinshasa (former Belgian Congo) which had a production of 15 million carats in 1968, equal to 47% of world production. In the past six years, there has been a remarkable increase of industrial diamond production in the USSR, which now ranks second with a production of 6 million carats, equal to about one-fifth of world production. South Africa now ranks third followed by Congo-Brazzaville and Ghana. No natural diamonds are produced in the United States. Since the discovery of an economical method for synthesizing small diamonds, there has been a rapid increase in synthetic production from 4 million carats in 1962 (1 carat equals 200 mg) to 11.5 million carats in 1968. Table 15.4C.1 gives the gradually increasing imports of industrial diamonds and indicates a relatively stable price. In 1968, the imports of industrial diamonds were 13.5 million carats with a value of $59.2 million. Table 15.4C.2 shows the rapidly increasing imports of cut and uncut gem diamonds into the United States. In 1968 the United States imported 2.5 million carats of uncut stones with a value of $166 million and 1.5 million carats of cut stones with a value of $175 million. Diamond marketing is dominated by DeBeers Consolidated Mines, Ltd., which, through subsidiaries, controls many of the major African diamond deposits. More important economically, however, through its Central Selling Organization, DeBeers markets 86% of the non-Communist world's natural diamonds, including most of those derived from deposits outside of corporate control. In 1967 the mines owned by DeBeers produced nearly 8 million carats, and the Central Selling Organization sold over $600 million in gem and industrial diamonds. The dominance of diamond sales by

Jan 1, 1976

By Alfred H. Hesse, Edwin T. Myskowski

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per 100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series, for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship p to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distributi0n line is [w = Cx" [I]] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By William C. Marshall, Frank G. Norris

THE term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open hearth shop is dependent on the blast-furnace capacity rather than on its own needs for the amount of iron available are among those which, in contrast to "unit operations," we have chosen to call "total operations," Many of these problems, such as charging delays and the general mechanical problem of material handling, are so familiar that merely to define "total operations" brings them to mind. These problems are of such importance that already they have received careful thought and study and probably will merit further study. As will be shown later, these mechanical problems are so intimately related to metallurgical problems of total operations that the effect of certain changes cannot be ascribed with certainty to either a mechanical or a metallurgical cause entirely. Although the problems coming under the general term of "railroading" are included in the problems of total operations, two others are selected for the discussion of this paper. One of these is strictly a problem of composition; the other is strictly a problem of tonnage production. The problem of phosphorus is present whenever basic open-hearth slag is used in the blast-furnace burden. This practice has not secured universal acceptance chiefly because of difference in preference for high-manganese or low-manganese pig iron. If high-manganese (2.00 per cent) iron is to be made, open-hearth slag as a source of manganese is usually cheaper than man

Jan 1, 1943

By Donald C. Bradford

THE place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past 10 years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. DIVISIONS IN DEFINITION OF FIELD OF GEOPHYSICS Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of financial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or so of the earth's. crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1942

By W. T. Bishop

FOR many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. HISTORY The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and coat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree-rosin and turpentine-but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is, supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores" industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.1 In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1946

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly i00 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi¬tion is accompanied by a change in volume of as much as S per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potters have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to g0 per cent Mn. is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to ½ in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

Engineers who are in charge of industrial operations, and their number is legion, sense as much as anyone the present feeling of unrest in the' country and more than anyone else realize the present inefficiency of labor. Undoubtedly the two phenomena are closely correlated and no doubt are due to a multitude of causes which it will be impossible to enumerate. From my experience in mining I estimate that the present efficiency of labor is only about two-thirds of what it was under pre-war conditions. In the mining industry, at least, we have not a large surplus of men looking for work and usually under these conditions men are rather more independent and will not work as efficiently and faithfully as if they felt there were plenty of men ready to take their places. Wages in metal mining have advanced more than the increased cost of normal and sane living. The result is that the men often work fewer days in a month and do not seem to have very much interest in their work while actually engaged in it. Then again, they have been listening to the more or less vague propaganda of the I. W. W. and the radical wing of the socialists, who are harping on the fact that the distribution of newly created wealth is unfair and that the laborer really is not working for himself or his fellow laborers but is carrying on his exertions for the benefit of a small and lim-ited class of exploiters. A continued harping on this view is bound to influence the judgment of even a conservative workman who is not a student of economics and who hears little or nothing upon the other side. I am a great believer in the common sense of the American people and in the long run I do not think that they will be carried away by unsafe doctrines. The trouble with so many of these propagandists of industrial in-equality is that they do not differentiate between production and dis-tribution. Even if we admit that distribution is unfair, unless goods are produced there will be nothing to distribute. A great many unthinking people seem to feel that wages are paid out of a pot which is inexhaustible and do not realize that eventually what comes out of the pot can never exceed what is put into it. The workman is not paid in money but is paid in goods, money as we all know being used simply as a measure of value and a medium of exchange, and that all that can be used to pay the laborer is what he produces.

Jan 11, 1919

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE