Search Documents

By R. P. Agarwala, M. S. Anand, S. P. Murarka

Using the residual radioactivity technique, grain boundary diffusion of chromium in the a phase and lattice diffusion in the a and the ß phases of zirconiuttz have heen studied. The diffusivities (in units of square centiwzeters per second) have heen expressed as THE rate of diffusion of atoms along surfaces and grain boundaries is much greater than that through the bulk of metals. These processes dominate over volume diffusion at lower temperatures and can be isolated from it by virtue of the fact they yield high diffusion coefficients and low activation energies. In zirconium, however, it has been difficult to identify the volume-diffusion parameters separately. The values of diffusivities in a and ß phases yield activation energies which are much lower than those for volume diffusion calculated from semiempirical or empirical relations.1-3 Diffusion frequencies (Do) are also low, especially in the a phase, and they yield negative entropies of activation.4 Similar results have been obtained for the diffusion studies in titanium.5 It is yet to be investigated whether in these cases diffusion is controlled by some extraneous factor like high reactivity of these metals, or some different mechanism is operative as suggested by Pound et a1.6 However, Federer and Lundy,7 in a recent study of the diffusion of zir-conium-95 and columbium-95 in zirconium, and Gibbs et al.,8 in the study of impurity diffusion in titanium, found a temperature dependence of D, Do, and Q. Their study yielded low values of Do and Q at low temperatures, as has been found by other workers, and fairly high values at high tempera-

Jan 1, 1965

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may he what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will he saved, and the information will be sent more promptly and in more usable shape. The members of the institute can be of service to the Library by forwarding copies of mining-reports, naps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 7, 1913

E. T. DUMBLE, Houston, Tex.-This paper is a continuation of one that was published by Mr. Garfias, I believe, in the Journal of Geology, 1912, in which he gave the results of his investigations in Mexico, showing that the basalt extrusions frequently did not come up as cones. but reached the surface as a small neck and then mushroomed out into a sill, penetrating the beds both in limestones and in shales. He has continued his investigations to show that as these basalt protrusions came up they forced the strata into a funnel shape at the top instead of throwing them out altogether. While this may be true concerning these particular beds, there are other places at which the basalt does appear clearly as cones and dories, and there the funnel structure does not exist. We know that the sills are there, because we find them in the wells. In one well that I know of. we found a 2-ft. sill of basalt at about 1600 ft. and oil below it at about 2100 ft.; others have gone through similar beds. We also know that there. are cones, because north of the Ranuco River one well struck basalt at about 800 ft. and continued in it for several hundred feet-did not pass through it at all. This paper of Mr. Garfias will give us considerable help in that oil field. W. E. WRATHER, Wichita Falls, Tex.-I would like to ask for information as to the temperatures of Mexican oils. I have heard a number of conflicting reports about the high temperatures of the water and oil, and the relationship between them.

Jan 1, 1918

By A. S. Learoyd

THE Anthracite Division, Bureau of Distribution, of the United States Fuel Administration, came into existence about Oct. 20, 1917. There had been no definite policy determined upon and the distribution had been carried out by the producers and distributors of this fuel as under normal conditions. The domestic sizes had been shipped from the beginning of the coal year on Apr. 1 in about their usual proportions to the various sections of the anthracite consuming territory of this country, which, in a general way, extended as far west as Nebraska and Montana, and in the south along the Atlantic seaboard to Florida. With the advent of cold weather, about the middle of November, acute shortages commenced to develop all over the northeastern section of the country, due to largely increased demand by the public in general, to enormously increased population in centers where industrial war activity was concentrated, and by the needs of the war industries themselves. Commencing with the early part of December, this demand was aggravated by extreme low temperatures and heavy snow; and the production decreased for the same reasons. From that date until the change in the weather, about the latter part of February, it was simply a question of getting coal into communities as emergencies occurred, to take care of individual cases. No definite plan of distribution could be followed. The coal mined between Apr. 1 and Nov. 1 had been distributed as mined and, therefore, only current production was available for distribution. The Anthracite Division, during this period, consisted of a Director, two assistants, together with an office force of seven or eight clerks and stenographers.

Jan 8, 1919

By John E. Udd

Introduction During the very long period in which man has mined minerals from the crust of the earth, falls of ground and collapes of under- ground workings have been the causes of a significant part of those accidents which have resulted in either death or in injury. At present, because of improvements in the approaches to the design of underground structures, in equipment, and in attitudes towards accident prevention, the proportion of accidents due to instability of rock is probably far less than it was historically. Nonetheless, in spite of the many advances which have been made, instabilities still account for about one-quarter of all fatalities, and one-tenth of all of the injuries, in the minerals industry. The means must be found whereby both the numbers of accidents and the accident rates due to falls of ground can be reduced to the lowest levels possible. At the outset it should be stated that, short of suspension of all mining activity, it will probably never be possible for us to eliminate accidents completely. Most human enterprise involves unknowns and risks, and mining is no exception. A certain number of accidents, then, must be viewed as the inevitable consequence of our attempting to work with unknowns and to make decisions that involve uncertainties. However, in retrospect, many instabilities can be attributed to factors which could have been within our control. The preventable accident must be eliminated. It should be our goal that we make every effort to direct our skills and technology to the creation of a safer working environment and should be constantly striving to

Jan 1, 1983

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furbish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 10, 1913

By Philip Drinker

IN THE mining and metallurgical industries, numerous problems arise requiring determinations of solid and of liquid particles suspended in air. Frequently, these problems are of local interest and involve purely economic or operating difficulties; on the other hand, toxic effects from the inhalation or the ingestion of substances suspended in air may be a matter of concern. For checking up process improvements or for determining ventilation efficiencies in problems of this general nature, various methods have been proposed. Although simpler methods are often satisfactory, precipitation combines several desirable features that other methods lack. This paper is, therefore, devoted to a discussion of portable alternating-current precipitators applicable to the quantitative determination and microscopy of dusts, fumes, and smokes in air. Small particles suspended in gases, such as air, are referred to in the literature as aerosols or suspensoids. Of these terms, suspensoids appears to be preferable as being more nearly in keeping with words in everyday use. In problems involving air pollution by small, particles-by suspensoids-it is convenient to distinguish three broad classes based on the size, the degree of dispersion, and the method by which the particles become suspended in the air. Dusts.-Particles or aggregates of particles, 150 to 1 micron in diameter, that are thrown into the air by mechanical agencies are termed dusts. Examples are silica, talc, cement, organic dusts such as hard rubber, starch, and cocoa; flocculated fume and smoke products. Fumes.-Particles, 0.2 to 1 micron in diameter, formed from chemical or physicochemical reactions are known as fumes. Examples are ammonium chloride, lead and mercury, zinc and magnesium oxides, fogs, and acid mists.

Jan 3, 1925

By D. R. Mitchell

This paper discusses some of the fundamental physical and chemical characteristics of coal in Illinois that affect its preparation for the market. At the present time preparation consists almost entirely of sizing and hand-picking. The washing of coal has almost entirely disappeared from the state. This is a rather startling fact when one considers that in the year 1908 Illinois outranked all other states in the quantity of coal washed and a few years later, in 1912, 85 washing plants were reported. Two reasons are apparent for this change. One, which is probably the most important, is that immense areas of comparatively clean coal were opened; the other is that many of the early washing plants were inefficient, so that washed coal was looked upon with disfavor in many trade centers. Objectives of Operators Some of the outstanding preparation aims being given due consideration by operating men are: 1. The greatest possible production of lump and domestic sizes which bring in the market at least $1 per ton more than the fine sizes or screenings. 2. Efficient screen sizing with as little breakage as is consistent with economical operation. 3. The removal of extraneous ash and sulfur. 4. Utilization of low-priced screenings. 5. Suppression of dust in domestic coal shipments. Preparation Underground To get the greatest possible production of the larger sizes, preparation must start at the face. Improvements in blasting and loading have increased the sizes larger than 2 in. by as much as 20 per cent. at some mines. Tiffany and McKitterickl report the results of an investigation they made at a mine in southern Illinois in which, by a carefully controlled

Jan 1, 1931

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-clays, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references' and copies of articles on-mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 7, 1913

By John Dresser

General THE controlling supply of asbestos for the world is obtained from southern Quebec, 150 miles or less north of the international boundary line between Canada and the United States, and about 75 miles south of the city of Quebec. The principal production is furnished by eight mines, seven of which occur within a distance of 6 miles, but there are also several smaller properties in the vicinity. The industry was begun in a small way some 35 years ago and has advanced more or less regularly ever since. The annual production now exceeds 100,000 tons and its value is about $3,000,000. It represents over 80 per cent. of the world's production. History Asbestos has been known in the eastern townships of Quebec since 1847, when attention was called to it in an official report by Sir William Logan, the first Director of the Geological Survey of Canada, but it was not until 30 years later that it came into commercial importance. The largest deposits, those of Thetford and Black Lake, were found in 1877 during the construction of the Quebec Central Railway. Work was begun upon them almost at once and has been continued ever since. The Danville mine, the next largest producer, was opened in 1879, and the slip-fiber deposits of East Broughton were located shortly afterward. For the first 15 years only the "crude" asbestos was recovered; that is, fiber long enough to be extracted by hand cobbing. Although this is still a valuable part of the production, it is now a relatively small part of the total output.

Jan 9, 1914

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By Perry Harrison

THE mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process-flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiating by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported.

Jan 1, 1930

By Luther W. Lennox

During the last few years, one of the great problems in the milling of all ores has been that of grinding. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of grinding to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of grinding methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative grinding resistances of a number of ores now being milled in this country and Alaska, the manage-mxitofthe Portland mills requested Samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh screen; in the screen analyses tabulated and plotted herewith, the 150-mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves. The experimental grinder was a small iron tube-mill, 8 by 121/2 in., in which was placed a definite number (74) and weight (3450 gm.) of 3/4-in. steel balls, 1 Ib. water and 1 Ib. ore. To obtain uniform conditions, each ore was first crushed and screened, and from the sized products a "standard feed" was artificially prepared, the same standard being adopted for all tests in that particular series. The prepared feed was

Jan 1, 1920

By G. R. Fitterer

BY means of the C-SiC thermocouple1, liquid metal temperatures have been found to vary much more than was previously supposed, and fortunately these variations can be directly associated with some of our former knowledge which combined to form the "art" of liquid-metal manipulation. COMMERCIAL DEVELOPMENT OF THIS DEVICE Several types of installations are operating in different plants. There are so many variables in steel plants in regard to operation, pro-cedure, arrangement of pouring platforms, ladles, etc., that most of the installations now in service in this country are "tailor-made"; never-theless, it is felt that satisfactory gains have been made inasmuch as each installation has indicated some effect of temperature upon the metal-lurgical operation, and has pointed the way toward technical and finan-cial benefits. In most cases, it has been necessary to accumulate the temperature data until sufficient metallurgical information is available for the drawing of conclusions. When mechanical difficulties have been eliminated, a distinct correlation of these factors has been obtained. The installations now in service. are used for the determination of temperatures in the basic open-hearth furnace prior to tapping and in ladles from both acid and basic furnaces prior to pouring. Some of the installations are in shops making the higher priced steels; others are in "tonnage shops." The errors of human element, smoke screens and emissivity corrections connected with the use of the optical pyrometer do not affect the C-SiC thermocouple readings. The accuracy of the C-SiC- thermocouple and the temperatures measured are discussed later in this paper.

Jan 1, 1936

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,900. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,&apos; the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1942

By Webster Hodge

MALL generators and motors are required to Soperate, in some critical applications, at temperatures where cold-worked silver-bearing copper re-crystallizes. Copper containing up to 30 oz Ag per ton has been used for many years to build the highest grades of commutators and slip rings. With failure of commutators impending because silver-bearing copper cannot withstand the stresses imposed at these higher temperatures, Cr-Cu was tried as a substitute with varying degrees of success. Cr-Cu proved difficult to fabricate because a critical heat treatment was necessary to obtain sufficient ductility. Besides, its rupture strength was shown to be low at operating temperatures, its electrical conductivity lower than desired, and its cost high. Furthermore, it often contained hidden flaws. The Nippert Electric Products Co. set out to find a better material by undertaking a research project with the stated objective of providing a material suitable for commutators that would have 1) a softening temperature above 750°F (400°C), 2) a minimum electrical conductivity of 90 pct of that of pure copper, 3) a strength not less that that of cold-worked silver-bearing copper, and 4) a materials cost of not over 1.5 times the cost of copper containing 25 to 30 oz Ag per ton. No commercial alloy met these specifications. However, it was found that copper containing from 0.18 to 0.35 pct Zr could be produced quite easily in the laboratory, and promised to fulfill the major requirements noted above. Interest naturally centered in the lower part of this composition range, since such alloys gave somewhat better electrical conductivities, and were lower in

Jan 1, 1958

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By D. M. Deason, R. M. Chhatre, G. Y. Onoda

INTRODUCTION The treatment of colloidal suspensions is a subject of increasing interest in mining and benefication (1). Colloidal suspensions are not readily operated upon by mechanical and physical methods useful with coarse suspensions, such as filtration, thickening, and flotation. This is because colloids are strongly affected by interfacial and interparticle forces that may be large compared with, and resistant to, external forces. The degree and type of interactions between colloids can be modified by small additions of reagents such as coagulants, flocculants, dispersants, and immiscible liquids. These alterations in turn change the properties of the suspension and provide possible opportunities for transforming suspensions to a more favorable condition for a given processing operation. Phosphate slimes are an example of a colloidal system of interest today. In the mining and beneficiation of phosphate rock in Florida, slimes are a waste product. The phosphate ore (called matrix in the industry) is slurrified hydraulically and pumped to a beneficiation plant, where the -150 mesh material is removed by cycloning from the coarser phosphate rock and silica. The resulting -150 mesh slurry, called phosphate slime, is pumped to large impoundments. The solid content of the slime entering the impoundment is around four weight percent, and over 80% of the solids is less than one micron in size. The immediate problems with phosphate slime relate to their disposal (2, 3). The disposal problem is associated with the very large volumes and the poor dewatering characteristics of the slimes. To have sufficient impoundment volume, large earthen dams are built around the mined areas. The volume above ground level approaches and

Jan 1, 1980

By Clarence P. Linville

It is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed. The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which make the fuel practically uniform; the Gayley

Jan 1, 1911