Search Documents

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

By Strathmore R. B. Cooke, William F. Stowasser

RESULTS presented in a previous paper1 have shown that the strength of fired pellets made from eastern Mesabi magnetite concentrates containing 8 to 9 pct Si02 as quartz and silicates is due to several processes which occur during firing. These are: l-recrystallization and cementation of the fragmented magnetite grains; 2-formation of slag from reaction between the quartz, silicates, and available ferrous iron, followed by slag-bonding of the magnetite grains; and 3-oxidation of the magnetite to hematite and subsequent recrystallization and grain growth of this constituent. Microscopic examination of all magnetite pellets fired in one operation in small and large-scale pilot plant furnaces and possessing normal strengths shows that the processes 1,2, and 3 have taken place; where strengths are low and the pellets are otherwise sub- normal, one or more of the processes has not occurred. For example, soft and friable red pellets may contain a central core of slag-bonded recrystallized magnetite which is strong enough in itself, but the shell contains only slightly recrystallized hematite, indicating that the maximum temperature reached was too low. Processes 1 and 2 can occur only under reducing conditions, as for example, when coal is intention- ally added to the original pellets; under neutral conditions, when pellets are fired in an inert atmosphere; or when pellets are brought so rapidly to temperature in an oxidizing atmosphere that oxygen diffusion to the core lags behind the recrystallization and slagging effects. This last-mentioned process has occurred in all pilot-plant shaft fur-

Jan 1, 1952

By Paul H. Rydlund

Substantial priming was a considered necessity for proper initiation of ammonium nitrate-fuel oil mixes as ANFO began to carve its niche in the mining industry in the latter fifties. Heavy priming accompanied the introduction of prills and oil to many blasting operations, large charges of high explosives were commonly used at the bottom, top and frequent intervals throughout the column. As the quality of ammonium nitrate improved and operators became more experienced, primer costs began to diminish. Increased experimentation continued with reduced primer costs a main objective. Cast primers were introduced and became accepted as an excellent companion for ANFO. Although the trend toward larger diameter boreholes became increasingly popular, emphasis on lower and lower priming costs continued. A primer was simply required to produce any type of initiation within the ANFO column to be considered adequate. Suddenly ANFO priming had digressed from excessive to marginal. Early experimental data from test site and laboratory indicated that ANFO had a tendency to react inefficiently in the initiation region of the column unless substantially primed. This was evidenced by the presence of unstable reaction rates detected with newly developed detonation velocity measuring equipment. These low order or "transient" velocities were believed to originate because of inadequate primer strength or a primer diameter to column diameter mismatch. However, the nature of this experimental work was generally confined to small diameter column charges detonated in iron pipe simulated bore-holes. It was questionable whether the smaller scale laboratory data was applicable to large 12 1/4 and 15-in. boreholes.

Jan 3, 1973

By P. F. Gnirk

Consideration is given to creater formation with shallow, contained, chemical explosions in rock masses which exhibit different inherent physical and mechanical properties as determined by standard laboratory techniques. The primary purpose is to determine whether or not a simple but useful generalized correlation can be established between explosive crater formation and one or more common rock properties. Such a correlation could be beneficial in predicting with some degree of reliability the size of a crater which could be expected in a particular rock type for a given input of explosive energy. A series of crater formation experiments employing constant weight charges of Gelex 2 explosive was conducted in five submembers of the taconite formation at the eastern end of the Mesabi Range in northeastern Minnesota. Five mechanical and physical properties-unconfined tensile and compressive strengths, Young's modulus of elasticity, longitudinal wave velocity, and density-were determined by conventional laboratory techniques using core samples from the taconite submembers. Although insufficient data were obtained to warrant the use of mathematical methods in the determination of empirical relationships, the results provided a fairly strong indication that with an increase in magnitude of any one of the five rock properties definite decreases in the optimum crater volume and surface area occur. Furthermore, for a constant explosive energy input, the presence of bedding planes and joint systems in a rock mass influences the formation of craters in such a manner as to increase the volume of rock broken substantially above that expected from the same rock mass without joint systems and, in particular, without bedding planes.

Jan 1, 1968

By Tran K. Van, Francois E. Heuzé, Richard E. Goodman

Sound design of structures founded in or upon rock requires that the deformability of each rock member involved be characterized. This can be done by means of loading tests (plate bearing, flat jacks, borehole jacks, pressure chambers, etc.) or through convergence measurements (tunnel convergence, roof sag, etc.) in exploratory works. Analysis of data will be qualitative (degree of nonlinearity, creep behavior, scattering of results over a number of sites, etc.) and quantitative (modulus of elasticity or deformation). Some of these tests involve a very bulky apparatus and are expensive to perform. On the other hand, for the purpose of mapping and describing the various rock members which occur within a given site, many feet of diamond drill holes are frequently completed. Even with the optimum equipment and expert drillers, however, quantitative characterization of the rock units on the basis of tests on returned samples is apt to be misleading; the softer and weaker components of the rock tend to be lost and the fabric of the rock block- fracture system in situ is not sampled. Laboratory moduli of elasticity have proved to be consistently higher than in-situ values selected for engineering purposes. This led to the design of instruments which would operate in boreholes, combining the advantages of a reduced size and a deeper investigation, from the surface to several tens of feet. BOREHOLE DEFORMABILITY MEASURING INSTRUMENTS In the last 10 to 15 years, a number of testing devices have been con- structed which can be inserted into a borehole to apply a load and mea-

Jan 1, 1972

By Roy Moore

THE Tom Reed Extension and Big Jim mines of United Eastern Mining Co. are situated in the Oatman district, Mohave County, Ariz., about 28 miles southwest of Kingman, the nearest railway point. Articles descriptive of the mine surface plant, mill construction, and plant operations have been written by Otto Wartenweiler1, the designing engineer; Wheeler 0. North,2 when he was assistant general manager for the company, and Earle M. Bagley, mill superintendent.3 The last article covers average costs for the full time the mill was operated. The geology of the mines is described by F. L. Ransome4 of the United States Geological Survey. Production was started in January,. 1917, and the known orebodies were exhausted in May, 1925, showing a life of seven years and five months. On account of the comparatively short life and the fact that stoping operations were confined to two orebodies, little experimenting was done with mining methods. The two orebodies were in what is generally called the Tom Reed-United Eastern vein, which occupies a fault fissure having a normal displacement of several hundred feet. Seven or eight very productive ore shoots were mined along this vein in a distance of 1 ½ miles, the two worked by the United Eastern being 1 mile apart. The maximum dimensions of the Tom Reed Extension ore shoot were height, 750. ft.; length, 950 ft.; thickness, 48 ft. The vein structure varied from a solid quartz-calcite filling to a series of parallel stringers separated by andesite. From this body, 511,976 tons of ore were mined. (Fig. 1.)

Jan 1, 1928

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

By Ben L. Seegmiller

Introduction The profitability of an open pit operation depends to a large extent on the use of the steepest pit slopes possible, provided they do not fail during the life of the mine Optimum pit slopes can be designed by using rock mechanics technology. Such technology includes gathering and analyzing pertinent data prior to pit design, rigorous application of rock mechanics principles during the design process, remedial actions to improve slope stability, and monitoring slopes during the life of the mine. Ignoring rock mechanics technology in pit design may place the entire mining enter- prise in jeopardy Disruption of mining operations and safety hazards caused by slope instability can be severe. A classic case in point is the major slope failure (Seegmiller, 1972) that occurred at a southwestern US copper mining operation in 1970-1971 Minor slope stability problems initially amounted to no more than a nuisance, but in time, the unstable zones became larger, causing greater disruption of production and threatening safety Mining at or near the slide toe had continued throughout the period of slope failure, aggravating the already unstable condition The original plan for this pit called for mining the overall pit slope to 37.5" Mine operators were forced to lessen the back- slope angle in the hope that the failing rock mass would stabilize. However, stabilization did not take place, and when mining in the area of failure was completed, the overall slope had been reduced to approximately 27" Mining had been successful in removing only a small portion of the ore body at a high stripping ratio.

Jan 1, 1979

By Blamey Stevens

In this paper, which is a logical extension of my paper, The Laws of Intrusion,1 the various pressures of emanation and their mechanical causes and effects on the large scale of nature are determined, and a classification of emanations is deduced therefrom. • The Subterranean. Sea. The subterranean sea is here defined as the intercommnnicating water contained in the trains of pores and fissures of the rocks down to great depths. Whether the actual amount of water constituting this subterranean sea be large or small, does not enter into the present argument, since the static pressure of this water at any particular depth is not a function of the quantity : it involves only the depth and the density of the water. Densities. The total pressure at depths down to 10 or 15 miles is made up of the rock-stresses investigated in my previous papers, and the pressure of the subterranean sea. The latter component must evidently be equal to the weight of a solid column of the overlying water of unit sectional area. As mater expands with heat, it should really be necessary to sum the density at every level. A knowledge of the densities of mater under a variety of conditions is therefore needed, but does not seem ever to have been ascertained for such combined pressures and temperatures as we have to consider. The specific gravity of water at 28' C. for various pressures up to 400 atmospheres, has been determined by Barus, 2 who

Jan 1, 1913

By R. J. Wasilewski

Axial expansion has been determined by X-ray diffraction up to 600° to 760°C in a titanium and four high-oxygen alloys. Expansion data cannot be fitted to the usual quadratic expression and anomalies observed are believed indicative of the changes in the bonding configuration of the valence electrons. Furthermore, there is significant disagreement between data obtained on poly crystalline and single crystal powder specimens. The major disagreement occurs within the temperature range (-470°C) where both mechanical and electrical properties also show markedly anomalous behavior. X. HIS work forms part of an investigation of physical properties of pure titanium and its osolid solutiono alloys with oxygen and nitrogen. In view of the anomalies observed in both the electrical resistivity' and the susceptibility behavior it was decided accurately to determine the thermal expansion behavior of the pure and alloyed a titanium. PREVIOUS WORK The axial expansion coefficients reported for pure titanium are listed below. As can be seen, there is a marked discrepancy between the axial expansion and the experimentally determined coefficients on poly crystal line material. Thus, if we take the most recently reported axial expansivities3,4 we obtain perature interval of 25o to 700°C. The experimental value reported for polycrystalline metal is, however, of the order of 9.7 x 10o6 per OC. EXPERIMENTAL I) Pure Titanium. High purity titanium powder of -325 mesh was used throughout most of this work. The only significant impurities present were the interstitials, oxygen and nitrogen, which analyzed respectively 650 and 80 ppm. The purity of the ma-

Jan 1, 1962

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate of oxidation of ferrous iron to ferric iron in pure molten iron oxide by carbon dioxide + carbon moloxide mixtures at 1550°C. It is shown that the rate-controlling process is the interdiffusion of iron and oxygen atoms within the melt. The inter-diffusivity of iron and oxygen in the melt is obtained from the results and the value of (5.0 * 1.0) x 10-5sq cm per sec is recommended for the temperature of 1550°C. Similarly, it is also found that the rate of reduction of molten iron oxide is con -trolled by diffusion in the melt; however, apparent interdiffusivity values from these experiments are 10 to 20 pct higher than those obtained in the oxidation experiments, by virtue of convection arising from density difference. The results of the oxidation experintents are used to calculate an estimated self-diffusivity of iron in molten iron oxide of (1.5 * 0.5) x sq cm per sec. BECAUSE of the industrial importance of iron oxides, the study of the kinetics of both the reduction and oxidation of the solid oxides has received a great deal of attention. However, knowledge of the kinetics of similar reactions in the liquid state is very meager. Dancy 1 studied the kinetics of reduction of molten iron oxide by carbon in pig iron and found that the reaction is very fast. It was concluded from the results that the reduction of molten ferrous oxide is a first-order reaction up to 80 pct reduction, while

Jan 1, 1964

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

By J. W. Eckerd, P. S. Lewis, N. H. Coates

USBM designed, constructed, and operated an 18-in.-diam fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8%+ Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coeffients from the bed (-20 t 50 mesh mullite) to a water-cooled tube were about 75 Btuper hr-sq ft. Fluidized-bed combustion is being investigated by the U. S. Bureau of Mines (USBM) as a potentially cheaper method of firing power plant boilers. Lower combustion temperatures in fluidized beds—only 1400" to 1800°F-—should reduce fireside deposition and corrosion and nitrogen oxides production. Fluidized-bed combustion also offers possible advantages in the use of additives to control SO, emissions and amenability to processing of high-ash, high-moisture coals without special preparation. This paper describes development of a fluidized-bed combustor and the results of preliminary tests. Equipment and Procedure Fig. 1 shows the 8-ft-high combustor. A cone-shaped plate perforated by I/8-in.-diam holes supports the fuel bed and admits the fluidizing air; water passing through the 3/4-in. pipe extracts heat from the combustion bed. Fig. 2 is a flow diagram of the system. Coal is fed pneumatically to the base of the fuel bed. Combustion products are passed through two centrifugal separators to remove most of the entrained solids, then to a water

Jan 1, 1971

By D. Gupta, S. Weinig

This investigation comprises the study of dislocation-oxygen interactions in a! titanium and its effect on the ductile to brittle transition in titanium. Internal friction techniques using a low-frequency lorsion pendulum were used to study the oxygen atom interactions with dislocations in "superpurity" titanium. A calculation of the interaction energy between an oxygen atom and a dislocation, based on the "breakaway" strain resulted in a value of 0.015 ev as compared to theoretical values of 0.022 and 0.035 ev for edge and screw dislocations, respectively. Both the saturation of the room temperature decrement and the transition from ductile to brittle behavior occurred at 1.5 at. pct 0. It was proposed that the embrittlement was due to oxygen atoms immobilizing the dislocations. It was possible to increase the ductility of the Ti-0 binary alloys by decreasing the oxygen pinning. The increase in uniform elongation was 30 pct for an increase in the preanneal temperature of 300°C. ThE room-temperature ductility of a titanium is significantly affected by interstitial solutes. Although oxygen has a solid solubility of 15.5 pct by weight, the room-temperature ductility extends only to 0.6 pct.' The ductility precipitously falls at this concentration and the fracture characteristics change from ductile to brittle.2 The small effective bulk composition of solute required to destroy the room-temperature ductility of the titanium must be indicative of an in-homogeneous distribution of solute atoms. Internal friction techniques were used in this investigation to

Jan 1, 1960

By Carl E. Swartz

For many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By D. T. Peters, C. R. Cupp

Aging of commercial 18 pct Ni maraging steel and of related binary, ternary, and quaternary alloys has been studied by electrical resistivity, X-ray diffrac-tion, and hardness measurements. The aging process is in three stages: 1) recovery of martensite; 2) two precipitation reactions; 3) formation of nickel- rich austenite. The main objective of this work was to discover the nature of the Co-Mu interaction. Addition of cobalt to the Fe-18 pct Ni-5pct Mo alloy results in acceleration of the pvecipitation reaction by increasing the super-sat~lration 0f molybdenum. The cobalt-containing al- loys show no incubation period for the precipitation reaction, but the alloy without cobalt shows an initial slow reaction. These results are interpreted in terms of precipitation on dislocations. At low aging temperatures, the presence of cobalt leads to the appearance of a second type of precipitate which is a particularly effective hardener. Cobalt was found to retard the formation of austenite. Overaging is a combination of classical overaging and the formation of austenite in the structure. he- activation energy for the precipitation reaction determined from resistivity ,measurements is 42.8 kcal per mole and the growth of the precipitate is found to obey at law at high tenzperatures and a tU3 law at low temperatures. HE mechanism of strengthening of the 18 pct Ni maraging steels has been studied extensively since 1962.'-? The strengthening is due to precipitation hardening of the martensitic matrix. The main precipitate is an inter metallic compound involving molybdenum, but there is disagreement about its identity.

Jan 1, 1967

By Harold W. Aldrich, Walter G. Scott

The leaching process of the Inspiration Consolidated Copper Co. is based upon the solubility of oxidized copper in sulfuric acid and the solubility of sulfide copper, largely in the form of chalcocite, in ferric sulfate solution. This necessitates the carrying of a rather large amount of iron in solution. The ferric sulfate is regenerated from ferrous sulfate by the oxygen given off at the anode during electrolytic precipitation of the copper. In September, 1924, excavation was started at Inspiration, Arizona, for the construction of a plant to treat 7500 tons of ore per day. When the plant was begun, the fact developed that by a minor change in the height of the overflow on the leaching tanks, 9000 tons could be charged into each tank and treated satisfactorily. This determined the maximum capacity of the plant as 9000 tons per day. The first ore was charged in October, 1926, and there are now available the records of five complete years of operation; namely, 1927 to 1931, inclusive. The original estimate of copper content of the ore to be mined for this plant was 1.19 per cent, of which 0.77 per cent was as oxide and 0.42 per cent as sulfide. From the metallurgical results obtained at the 35-ton pilot plant, it was estimated that a 90.0 per cent extraction of the oxide copper and a 75.0 per cent extraction of the sulfide copper could be made. It was estimated that the tailing would carry 0.182 per cent total copper, resulting in a

Jan 1, 1934

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its asso¬ciated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By Carl Swartz

FOR many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931