Search Documents

By I. D. Shah

A roasting procedure for synthetic copper sulfide which results in a reproducible transient melting at 450° and 470°C is described in this paper. Possible causes for this melting phenomenon are suggested, and also a procedure to avoid it during the roasting. This melting is believed to be responsible for the occasional occurrence of stickiness in the commercial roasting of copper sulfide concentrate. Many workers have studied the roasting of copper sulfides, but only Lewis et al. have reported that fusion and, in some cases, fusion with "boiling" occurred in the neighborhood of 450°C. The DTA and TGA apparatus, the materials used in this investigation, and the discussion of chemical reactions occurring during the CuS roasting are described in an earlier publication. CuS, in the form of either pellet or powder, was heated at 280° to 330°C in a flowing air or 30% 02: 70% N2 atmosphere. Heating was continued at this temperature until no further weight increase due to sulfates formation was observed on the TGA thermogram. This is believed to be due to the inability of SO, to diffuse out from the sulfate layer on the surface of the pellet, thus halting the sulfate-forming reactions. Hereafter, the sample oxidized in this manner will be referred to as "partially oxidized CuS." X-ray analysis and microscopic examination of a polished cross section of a partially oxidized CuS pellet showed the following order of layers starting from the center of the pellet: Cu2S, Cu2O, CuO • CUSO4, and CuSO4. A bare thermocouple inserted in the center of a partially oxidized CuS pellet (2.5 g) did not indicate any noticeable change in the temperature of the pellet when melted at 450° to 470°C in an inert or oxidizing atmosphere. During the preparation of a partially oxidized pellet, the temperature of a CuS pellet increased by 50°C due to the exothermic formation of sulfates in air at 320°C. The endothermic peak associated with the melting phenomenon at 450°C is shown in [Fig. 1.] A CuS pellet (0.2 g) was oxidized in flowing air (150 cc per min) at 10°C per min up to 320°C and held there for about 2 hr. Then, N2 replaced air and heating was continued up to 500°C. The exothermic peak at 320°C represents an overall formation of sulfates, and an endothermic peak at 450° to 470°C represents the melting phenomenon. To observe the melting visually, a small (50 mg), partially oxidized CuS pellet was heated (in static air) in a hot-stage microscope. The melting phenomenon was observed on an auxiliary TV screen. The sample

Jan 1, 1976

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

THE importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature." PREPARATIONS OF SPECIMENS In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal frictions is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm. Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tensiontesting machine, using special grips10 to ensure axial application of the load. The rate

Jan 1, 1941

By P. W. Bakarian

PREVIOUS determinations1,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc-also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {102}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. EXPERIMENTAL METHOD Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 32 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. 2. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in, and evenly etched in dilute hydrochloric acid to a diameter of 0.038 ± 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1941

By O. Schaaber

THE existence of isothermal martensite without the presence of the athermal form thus far has been established only in a 6 pct Mn, 0.6 pct C steel' and a 23 pct Ni, 3.5 pct Mn-Fe alloy.' " Theoretical calculations, moreover, predict this phenomenon to be observable only within narrow composition limits.' In all other steels, it is generally considered that martensite inevitably forms upon cooling below the M, temperature. Even the possibility of isothermal martensite transformation has been questioned for the common steels, although Averbach and Cohen" showed that martensite formation does not stop when the cooling is arrested and that as much as 5 pct retained austenite may transform isothermally to martensite at room temperature. This note presents some observations made on a number of low alloy steels by dilatometric and inductive measurement of isothermal austenite transformation at various temperatures close to the Ms. In the dilatometer studies reported previously, austenitized specimens were immersed in a salt bath maintained at proper temperature and immediately inserted into the dilatometera8' already at thermal equilibrium with the bath. The dilation was read on a dial gage divided into 0.001 mm intervals. Induction measurements were made with a separate excitation source and a test coil, sealed together in a salt-tight case. The increase in the induced voltage caused by the transformation products was recorded at a paper speed of 4 mm per sec. The steels studied are listed in Table I. Specimens prepared from steels 1 and 2 were in the form of hollow cylinders 60 mm long, 10 mm ID, 14 to 16 mm OD, while specimens of steels 3 and 4 were in the form of notched-bar impact test specimens, DVM type. Specimens of steel 5 were in the form of strip, 7x0.3 mm. In the bainitic range, curves representing the amount of transformation vs log time have a single step appearance, as is shown by the curve of isothermal transformation at 320°C in Fig. 1.Y ransformation proceeds in accordance with the Austin-Rickett equationo P -----------= k t" 100-P where P is the percentage of transformed austenite, t is time, and k and n are constants. Near the M, temperature, however, complex curves having two steps are observed. As shown in a previous papera for steel 3 isothermally transformed at 245"C, such complex curves can be separated into two separate transformations or reactions each following the Austin-Rickett equation. The values of n in the equation for a number of such two-step transformations are listed in Table 11 for steel 1. At transformation temperatures of 250" and 235"C, evidence of a second transformation is very

Jan 1, 1956

By E. H. Crabtree

THE heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. 1, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. 1, 1946, to represent the ferrosilicon medium. During the first of 'these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. FLOWSHEET The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through 11/2-in. and wet-screening out the minus 3/16in. portion. The minus 1 1/2 plus 3/16in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone .concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. HEAVY-MEDIA PLANT The heavy-media cone plant treating the minus 1 ½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig 1.

Jan 1, 1947

The Gooseberry Mine is located 38 krn (24 miles) by road east of Reno, 13 km (8 miles) south of Interstate 80. The mine was originally discovered in 1906 and remained in the control of the Martin family of Fresno, who worked the-property with Mexican ranch hands for 68 years. Westcoast took over the property in 1976 from Apco Oil Corporation. During the time the Martins operated the mine, a 305 m (1,000 ft) inclined shaft was sunk with drifts developed on eight levels exceeding a total of 3,000 m (9,000 ft) in length. It is interesting to note that for over one -half century all development ore was stockpiled. West- coast, the United States mining subsidiary of Home Oil Company Ltd., Calgary, Alberta, completed sinking another vertical shaft to the 396 m (1,300 ft) level. Development work between 122 m and 305 m (400 ft and 1,000 ft) levels has proved the existence of a fine ore body over 300 m (1,000 ft) long. The silver-gold ore grade is fairly consistent in the vertical section, but copper, lead and zinc may show slight increases with depth. Average width of the ore bearing portion of the vein is 2.5 m (8.3 ft). Stoping is by cut-and-fill method. Average silver values within the ore zone have increased from the 152 m (500 ft) level to the 305 m (1,000 ft) level, although the gold values do show some decrease. It is not possible for the geological staff to predict the depth of the ore. However, several years of ore reserves have been proved in the existing mining areas. Important ore minerals are argentite, native gold, and electrum. Trace amounts of galena, chalcopyrite, and sphalerite are associated with the precious metal mineralization. The vein is mainly composed of calcite and quartz. Mine-run underground ore is dumped from the hoisting skip into a coarse ore bin followed by a jaw crusher, an impact crusher, and a 600 mt (650 st) fine ore bin. The mill has a capacity of 317 mt per day (350 st per day). Two-stage grinding is done by a rod mill followed by cyclones with the underflow sent to a ball mill in closed circuit with the cyclones. Cyclone overflow after conditioning receives a primary float in four 1.7 cu m (30 cu ft) cells and a second stage of conditioning ahead of 24 0.8 cu m (30 cu ft) secondary flotation cells. No cleaning stages are used. Flotation tailings are cycloned for a sand-slime separation with the sands used as underground stope fill and the slime portion to tailing dam storage.

Jan 1, 1981

By Fred J. Wright

ORIGINALLY, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are now literally the heart of the mining machine. During World War No. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Contamination of Oil Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the, proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the same time will lower costs for the oil by extending its life. Bulk purchases of oil should be limited to small sealed containers provided with a proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives, will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1946

By R. J. Sherman, M. R. Achter

IT has often been reported that coatings may strengthen single crystals and polycrystalline specimens of coarse grain size. This note reports the effect of a surface layer of fine grains on the creep-rupture properties of coarse grained nickel 99.8 pct pure. Sheet specimens were machined from cold-rolled material, finished by surface grinding and annealed at 1230°C in vacuum for 4 hr. Half of them were re-ground on faces and sides and annealed at 925"C for 1 1/4 hr. The double grind-anneal treatment produced a structure consisting of a surface layer of fine grains of 0.02 mm diam on a coarse-grained substrate of grains of 0.40 mm diam. Comparison with specimens which received only the single grind showed that the second grind-anneal did not alter the structure of the substrate. Several modifications were made in specimen design to eliminate erratic rupture behavior outside of the gage length. In the final design the gage section, oriented parallel to the rolling direction, was 1.00 in. long, 0.4 in. wide, and 0.0625 in. thick. End tabs were pinned in place. Although other configurations (welded end tabs, transverse orientation, and wider gage section) showed similar effects of a layer of fine grains, because of the erratic rupture behavior, only the data from the final design are reported here. Creep tests were performed at 650°C in air and in a vacuum of 10~5 mm Hg. Creep rates were measured from the movements of the lever arm. Since the broken sheet specimens could not be fitted together, elongations at fracture measured by means of gage marks, do not include the necked portions adjacent to the fracture. Results of the creep tests with and without the fine grained surface are given in Table I. An explanation for the lower strength in air than in vacuum has been proposed previously in terms of the reduction of crack propagation energy by gas adsorption.l In both environments the fine-grained layer produced a small decrease in minimum creep rate and, except for the shortest test in air, a substantial increase in rupture life. The elongation values at rupture, as they are measured here, do not demonstrate an appreciable effect of the grain structure but do show much smaller ductilities in air than in vacuum. Greater elongations maybe associated with the finegrained layer, however, especially in vacuum, in creep curves such as those in Fig. 1. Duplicate tests were not run to determine the re-producibility of the data. It is felt, however, that, in view of the consistent behavior, the prolongation of rupture life may be attributed to the effect of the fine-grained surface. In the data not reported be-

Jan 1, 1962

AVING started to tell you of working potter's clay for making crucibles and shells, the wish came to me to tell you of the practice of this art also. Although it may seem at first glance to be outside the order and purpose of my writing, he who considers well will see that it is not unrelated to it but proper, since it is wholly dependent on the agency and power of fire if it is to be brought to its perfection. Moreover, the potter's glazes and colors are all substances of various metals or impure minerals and therefore belong to fire. Since it is my intention to treat of fire, minerals, and metals for you, I surely should not have omitted this, particularly because it is a necessary art which enriches and is greatly praised both for its ingenuity and its beauty. The art of the potter has two sources as its principal basis. One comes from the art of design, the other from various alchemical secrets and elemental mixtures. In regard to these, I find that, in my opinion, all this art depends in the last analysis on four things: on good judgment in general, and on the art of design so as to be able to make the vessels beautiful and of good shape, as well as to ornament them with painting; after baking them well the first and second times, the next thing is to know how to make and apply the glaze well and to paint them with varied and appropriate colors. The fourth is to see that you have good, fine clay without small stones or lumps-indeed this is to be considered as the first thing. Now this that I have called clay is what many call cretaceous earth and some call argil. It is found and dug up when the masters wish to make use of it and is put in a container to be moistened. When it is moistened, it is beaten on a bench with an iron rod and very well prepared. Mixing it carefully, every small stone, lump, or other hardness that it contains is removed and cleaned away. Then a shaft [145V] of iron is fitted as the journal in a large wheel. On the other end of the journal a small wheel is made which forms an instrument for working that is called a lathe. Having put some clay on this, it is made to rotate by pushing with one foot, and, by rotating it, vessels are worked into a pleasing shape and size. Then they are taken off and put on a board to dry. After drying artificially or naturally they are painted red,

Jan 1, 1942

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

In the Ti-Cd system two intermediate phases, TiCd and Ti Cd, have been found and characterized by X-ray diffraction powder techniques. An earlier reference' had reported the existence of the compound Tisd. No structural details, however, were given nor was there any indication of the possible existence of other binary compounds. Studies of the solubility of titanium in liquid cadmium2 led to the discovery of both TiCd and Tisd. The solid phase in equilibrium with saturated solutions of titanium in liquid cadmium at temperatures below 620°C is TiCd, whereas TizCd is the equilibrium solid phase above 620°C. Both thermal analysis and X-ray studies show that a peritectic reaction between the y phase (~isd) and cadmium to form the 6 phase (Ti Cd) occurs at 620°C. X-ray diffraction powder photographs of material isolated from the ingots used in the solubility measurements as well as material prepared by a direct heat of the appropriate stoichiometric amounts of titanium and cadmium can be indexed on the basis of a tetragonal unit cell with a = 2.904 ± 0.002A, co = 8.954 * 0.004A, c/a = 3.083. No variation of lattice parameters indicative of a range of composition is evident. With four atoms in the unit cell the calculated density of the intermetallic is 7.05 g per cm3; the observed value is 7.07 g per cm3. The TiCd lattice is primitive as indicated by the fact that there are no systematic absences among hkl reflections. The absence of all hko reflections for which h + k = 2n + 1 is also evident. This systematic absence indicates the following two space groups, C\h — P4/n and D&~4/nmm; both groups, however, have the same two- and four-fold positions. Stoichiometry, symmetry and space group indicate two likely structure types. They are the PbO-litharge3 (B10) type and the Ti CU (B11) type. Spatial considerations favor the B11 structure with atoms placed in the following positions: 2Ti (c) 0, 1/2, Z; l/2, 0, Z 2Cd(c) 0, 1/2, Z; 1/2, 0, Z The TiCd structure may be summarily described as a layered structure in which double cadmium layers alternate with double titanium layers along the c-axis. The best agreement between calculated and observed intensities is obtained for the values ZTi = 0.608 and ZCd = 0.130. Calculated and observed powder intensities as well as other pertinent powder data are recorded in Table I. Interatomic distances for the proposed structure are recorded in Table II and are to be compared with the distances of closest approach for titanium and cad-

Jan 1, 1962

By Fred J. Wright

Originally, mining machines were actuated by purely mechanical mechanisms comprising cams, levers and gear trains, which became more and more complex as demands were made for additional operations that would increase mine tonnage. To simplify these intricate machines, development engineers began utilizing the principles of high-pressure hydraulics long employed for the control of various machine tools. The resulting specificially developed hydraulic systems are. now literally the heart of the mining machine. During world war NO. 2, very little fundamental change in design was made in existing mining machines, but because of the recognition of the merits of hydraulic application to the machines of war, it is reasonably certain that hydraulics will be applied to mining machines in the future to a much greater extent. This potential future indicates that a more thorough knowledge of hydraulics and its maintenance must be incorporated in mine operation. Maintenance of high-pressure hydraulic equipment varies considerably with respect to mine practice and conditions. The success or failure is largely dependent upon the hydraulic fluid and its care. Since all successful hydraulic systems have been designed around the use of mineral oil as the fluid, a complete analysis of this prime factor should be made to make clear the requirements of the fluid in a hydraulic system. Contamination of Oil Manufacturers of mining machinery usually have specified an S.A.E. rating or viscosity index of the proper mineral oil for use with their respective machines without considering the fact that many oils will meet these specifications but will not give the desired life or efficient operation. Hydraulic fluid should be specified as a good grade of mineral oil, such as turbine oil, having rust and oxidation resistance. It must have high chemical stability, high lubricity, and proper viscosity. These factors will minimize maintenance costs by reducing wear and the consequent replacement of parts, and at the Same time will lower costs for the oil by extending its life. Rulk purchases of oil should be limited to small sealed containers provided with a Proper pouring spout, thus reducing the possibility of contamination of the oil before it reaches the mining machine. The introduction of foreign matter, such as sand, water, coal dust and residue oil left in filling containers, will cause untold damage and maintenance expense. Sand, being one of the best natural abrasives1 will soon wear the close tolerances of the various hydraulic mechanisms to an extent that will necessitate complete replacement. Water is considered normally insoluble in oil, but because of the churning action of a hydraulic system water is broken down to particles so small that they remain in suspension. This suspension is known as

Jan 1, 1947

By E. H. Crabtree

The heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. I, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. I, 1946, to represent the ferrosilicon medium. During the first of these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. Flowsheet The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through I½- in. and wet-screening out the minus 3/16-in. portion. The minus 136 plus 3/16-in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. Heavy-media Plant The heavy-media cone plant treating the minus I½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig I.

Jan 1, 1949

By H. A. Sawin, C.M. Romanowitz

Placer dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were *designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry's history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. Deep Dredging At Hammonton, calif., yuba consolidated Gold Fields has, within= the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 80 ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7½-cu. ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1943

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By H. L. James

This paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4"; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas. Introduction The U.S- Geological Survey, in cooperation with the Geological Survey Division of Michigan Department of Conservation, has for the past three years been engaged in a restudy of the Iron River-Crystal Falls iron mining district of upper Michigan. The bedrock in a large part of this area is covered with glacial deposits as much as 500-ft thick, and, inasmuch as some of the rocks have moderate to high magnetic permeability, extensive magnetic mapping has been done to assist in unraveling the complicated structure of the area. Several types of instruments have been used, and the major purpose of this paper is to present comparative data on the field performances of some of these instruments so as to aid others who face similar problems elsewhere to evaluate and choose the instruments best suited for the work. The paper is directed primarily to geologists and engineers rather than to geophysicists, although some familiarity with the instruments is presumed. The geology of the area consists of a complexly folded series of weakly metamorphosed sedimentary rocks, including the iron formation, which rests on older greenstones. Although the iron formation itself is only locally magnetic, some of the beds stratigraphically above the iron formation are rather strongly so. By tracing these hanging wall magnetic anomalies valuable information is obtained from which the structure and distribution of the iron formation can be inferred. Critical anomalies range from 25 to 6000 gammas of vertical intensity. Many anomalies can be traced in part with the common dip needle, but detection of others requires more sensitive instruments.

Jan 1, 1949

By C. M. Romanowitz, H. A. Sawin

PLACER dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry's history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. DEEP DREDGING At Hammonton, Calif., Yuba Consolidated Gold Fields has, within the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 80 ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7 1/2-cu. ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1941

By William Metcalf

William Metcalf, Pittsburgh, Pa. : In rising to discuss Dr. Dadley's paper, I feel somewhat as I did at the Baltimore meeting —that a "crucible" man has no right to interfere in a "Bessenier" discussion; yet having read the paper very carefully, I feel impelled to say something, for two reasons: First, because I believe Dr. Dudley is entirely on the right and having undertaken and partly accomplished a great work, he .is entitled to the help of all who have experience in these matters; and second, because the data given force me to colicur in Captain Jones's opinion that the analyses are incomplete, since they ignore sulphur, copper, nitrogen, and possibly other injurious elements. In an experience of fourteen years, and with probably more than a hontlwl tests, we have never found the chemistry and the of crucible steel to disagree. If in any cave a disagreement tins sp- . peared, it has been our invariable custom to go over all our physirtal testa with great care, and if we found no error, then to refer the matter back to the cherubt, who has invariably found some unexjmted element to account for the trouble. It is only just to the chemist to say here, that ordinarily be is only expected to determine phosphorus, silicon, sulphnr. Generally the metals, with the exception of manganese, are not looked for, although a watch is usually kept for copper and arsenic. Further, in most cases we have found our own work more liable to be faulty than the chemist's. Having arrived then at such a degree of experience that we can preJict the analysis from our tests, or our tests from the analysis, with almost absolute certainty, I can see no reason why the same results map not be attained in the Bessemer practice. But two things are essential, neither of which we have here; first, cornplete analyses; and second, a record of the nature of the blow, the heat at which the ingots were bloomed, and the mile finished,—in short, a complete history of the This latter is quite as essential as accurate and complete analyses. Dr. Duclley ignores sulphur and copper on fair enough grounds commercially speaking, bnt when he announces so gmve a conclusion as he has reached, in a scientific way, the omission of any elementn that, may affect the conclusion is hardly justifiable. His diEerenvcs of phosphorus units, which I milst term units of rottenness 83 fr os phosphorus is concerned, and which I am sorry be did not llama wnits of alloys,—are very small, and if eulphur and copper hod been inclurlid they might havo upset hie conclusions sitogether, The

Jan 1, 1881

By C. M. Romanowitz, H. A. Sawin

PLACER dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry's history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. DEEP DREDGING At Hammonton, Calif., Yuba Consolidated Gold Fields has, within the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 8o ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7 ½ -cu- ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1941

By Matthew J. Hrebar

SINCE the first installation in 1936, the use of rubber-tired equipment for secondary mine haulage has increased rapidly. From August 1936 to January 1944, approximately 750 rubber-tired units were placed in operation. Of these, 650 units were installed after January 1940. During the year 1941, it per cent of the mobile loaded bituminous tonnage was hauled by rubber-tired equipment. This percentage increased to about 20 per cent during 1943. The first rubber-tired units were battery-powered tractor-trailer types. In the year 1938 the battery-powered self-contained car was introduced. In 1939, the cable-powered self-contained car made its appearance. These self-contained units are our modern "shuttle cars." By the end of 1941, approximately 15 per cent of the shuttle cars in operation were cable-powered. Installations made during 1942 and 1943 increased the proportion of cable-powered cars to about 40 per cent of the total number of shuttle cars in use. There is a marked trend toward cable-powered cars, although one need not make many trips to mines where both types are used to discover that opinions are highly controversial as to the relative advantages and field of use of each type. It is natural for mining engineers in the coal-mining industry to have diversified opinions regarding the use and application of coal-mining machinery. Coal mining is not a standardized industry; natural conditions vary from mine to mine. However, it is surprising how many operations in scattered fields arrive at the same conclusions and adopt similar methods. This happens not so much through cooperation and exchange of ideas as through hard, costly experimentation, involving months of low production and relatively high costs. What then, are the reasons for increased use of cable cars? Could it be that present scarcity of materials is forcing their use? True, battery cars require considerably more auxiliary equipment, but during 1942 it was no more difficult to obtain than shuttle-car cable. Furthermore, the trend toward cable cars started before curtailments on mining equipment took effect. Undoubtedly, cable-reel shuttle cars were introduced to produce coal at a lower cost by simplifying trackless mining through the elimination of auxiliary equipment, and by reducing the first cost on equipment. The theory of cable-powered shuttle cars is well based, as can be proved by successful operations. Many operators have weighed the advantages and disadvantages of each type carefully before choosing the type most suitable to their operation. Others have taken much for granted and accepted one or the other without much thought. At many small operations, low first cost is apt to be the deciding factor. One large company, with considerable experience in the use of battery locomotives, preferred to use cable cars even though it was neces¬sary to reduce the section voltage from

Jan 1, 1944