Search Documents

By Bernard Amadei, Richard E. Goodman

A medium is anisotropic if its properties vary with direction. This is the general characteristic of many rocks, for example, schists, slates, gneisses, phyllites and other metamorphic rocks. Bedded and regularly jointed rocks also display anisotropic behavior. This paper is concerned with the influence of rock anisotropy on in-situ stress measurements. It is limited to stress measurements by overcoring techniques for which strains and displacements are recorded either on the walls of a pilot hole at the end of one or several boreholes or within instrumented solid or hollow inclusions perfectly bonded to the surface of the pilot hole. The rock is described as homogeneous, continuous, anisotropic and linearly elastic. The following questions are answered with special emphasis on rocks that can be classed as transversely isotropic or orthotropic: the number of independent measurements obtainable in a single borehole; the number of boreholes required to determine the in-situ stress field; the influence of rock anisotropy on these numbers; the influence of the anisotropy type and the error involved by neglecting rock anisotropy.

Jan 1, 1982

Spencer Gulf takes off from the Great Australian Bight cutting a 200 mile deep wedge of water into the South Australia coastline. A pale winter sun shines yellowly on the choppy surface of this body of water which is progressively more salty as it approaches Port Augusta at the head of the Gulf. Once Port Augusta thrived as a grain port and the speedy clipper ships began or ended their legendary races there. On the eastern shores of Spencer Gulf, farm land spreads away from the water's edge. The western side of the gulf meets marginal grazing land of acacia tree and salt bush. Part way down the gulf, there are two industrial towns facing each other from opposite shores; Port Pirie on the east and Whyalla on the west. These towns are like half brothers, the common parent being the founders of Broken Hill Pty. Ltd., (BHP) who began lead smelting at Port Pirie and discovered iron ore near Whyalla needed for the lead smelting process. The iron deposits later became the inspiration for BHP's iron and steel business.

Jan 10, 1964

By Richard H. Sibson

Changes in seismic style along the San Andreas fault system appear to correlate with strike-parallel variations in regional heat flow. Large earthquake ruptures are associated with colder segments of the fault zone, while comparatively high levels of microearthquake activity and small to moderate shocks occur along the hotter segments, often in association with aseismic creep. Such behavior is consistent with geotherm and strain rate dependent profiles of shear resistance versus depth, constructed for quartz-bearing rocks. These profiles suggest that the transition from frictional to quasi-plastic behavior with depth should increase by a few kilometers passing from the hotter to the colder portions of the fault zone, giving rise to long-wavelength concentrations of distortional strain energy near the base of the seismogenic zone in the cold segments. Some support for this hypothesis comes from the observed deepening of microseismic activity passing northwest and southeast from the central Californian active region to the currently locked, ~400 Ian segments of the San Andreas fault that ruptured in 1906 and 1857.

Jan 1, 1982

By J. B. Woodworth

Under the above title it is desired to bring to the attention of assayers a short-cut method which has been perfected by Mr. A. S. Warren, of Buffalo, and the writer; has been used several years at three " Lake copper " refineries in occasional alternation with the regular " combination," or a wet and fire," assay; and has proved more rapid, and rather more accurate than the latter on all refined copper—namely, the direct cupellation of the silver chloride (+gold) precipitate, without scorification. No claim of priority is made for this direct method, as it has suggested itself to many others, and was mentioned by Mr. Warren in the symposium of assayers' results brought together in 1895 by the Secretary," after the plan and suggestions of Dr. A. R. Ledoux.† Lately, this important subject of assaying copper-materials seems to have been re-opened for discussion. The shortening of time by 'the direct method is so considerable (nearly 20 minutes on a batch)—to say nothing of the saving

Jan 1, 1902

By D. W. Fuerstenau

Locked-cycle grinding experiments on mineral mixtures provide a means to study circuit performance in simulated continuous grinding systems. Such experiments with calcite/quartz mixtures revealed that approximately twenty-five 2-minute cycles are required before the composition of the circuit product and the recycle material attain steady state. The circulating load, after steadily increasing during the first 15 cycles, continued to fluctuate over a narrow range. Previous batch ball mill grinding of mineral mixtures has shown that breakage rate functions of minerals are time- independent but composition-dependent. In the closed-circuit grinding of ores with constituents having different grindabilities, the grinding rate parameters for the components also would therefore change during the transient period. With fluctuations in feed composition occurring randomly every half to one hour in processing plants, it is quite likely that the grinding circuit can be in unsteady state perpetually. The significance of these observations is discussed in this paper in the con- text of the models used in control schemes for the grinding circuits

Jan 1, 1984

By E. W. Lithgow, E. G. Williams, R. R. Holbrook, B. R. Wilson

The mineralogy and geochemistry of Pennsylvanian shales and underclays were studied to determine their suitability for lightweight aggregate and refractory ladle brick. Eighty percent of the variation in bloating of shales and clays was explained by the variation of Si02, A1203, and fluxes (Fe203, MgO, CaO, Na20, and K20); 60% by variation in quartz, kaolinite, illite, and chlorite. The best bloating was exhibited by marine shales, whereas freshwater shales and underclays experienced little or no expansion. Regional paleogeographic maps o f Pottsville and Allegheny shales permit bloating to be geographically predicted. It was found that clays meeting the specifications for refractory ladle bricks were obtained from underclays having over 34.5% mica, over 40% kaolinite and less than 15% quartz. Underclays of this composition are confined to the lower Allegheney outcropping along the near-margins of the coal basin. The best clay is that underlying the Lower Kittanning coal. Porosity of the first fired brick was found to be inversely correlated with reheat expansion.

Jan 1, 1975

By R. T. Hukki

THE accepted basis of comparisons between mills of different diameter is the percentage critical speed. [ ] In the following analysis capacity, T, is expressed in short tons per hour, tph, and power consumption, P, in kilowatts, kw. Accordingly power consumption per unit of capacity, Po, will be expressed in kilowatt hours per short ton, or kw-hr per ton. In all equations D refers to the inside diameter of the mill in feet and v to the peripheral speed of the mill in feet per minute inside the liners. Comparison between separate mills must be based on equivalent grinding conditions, i.e., same feed, same size distribution of feed, same size distribution of product, and same percentage of solids. In addition, comparisons between separate rod mills must be based on the same rods, same type of liners, and same percentage rod load. Comparisons between separate ball mills presuppose the same balls, similar liners, and same relative ball load. The practical np-range through which the equations apply varies, being narrower for fine grinding in ball mills and wider for coarse crushing in rod mills.

Jan 7, 1954

By Rollyn P. Jacobson

The town of Pacific, in Jefferson County, Mo., is 27 miles west of St. Louis. Since the area lies entirely on the flood plain of a cut-off meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus* were used. In all but a few cases, the electrode spacing, A, was increased in increments of 1% ft to a spread of 30 ft and in increments of 3 ft thereafter.

Jan 2, 1955

By Dennis V. D’Andrea, Sidney M. Runke

This paper describes the Bureau of Mines-El Paso Mining and Milling Company cooperative research program at the Emerald Isle mine3 near Kingman, Ariz. This research program was directed toward developing in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 1,500,000 tons of ore under 200 feet of overburden adjacent to the pit. A test area in the pit bottom containing 15,000 tons of ore was blasted and leached. The results of this leach test were encouraging, and the entire pit bottom was leached in-place for about 7 months. Two test blasts under 200 feet of overburden and extending to 290 feet were detonated in an area near the open pit. The results of these blasts were evaluated by core drilling and permeability measurements. An in situ leaching system was designed, but not implemented, to recover copper from the 1,500,000-ton area near the pit. The company decided to terminate operations at the Emerald Isle mine in November 1975.

Jan 1, 1976

By E. Nelson Fell

As this plant is the first ever erected in British Columbia for the treatment of tailings by the cyanide process, and as the ores of this, mine are of a character not unusual among gold-ores of this Province, it is probable that a description of the principal features of the plant, and of the methods employcd in its operation, may be interesting. These works were designed after a careful study of the process, in a small experimental plant, for a period of six months. During this period ten percolation-tests on charges of tailings of 1100 lbs. each, eight percolation-tests on similar charges of concentrates, and twenty-six tests 011 concentrates in a revolving barrel, were made, besides laboratory-experiments. The ore consists of a quartz gangue, containing a little lime and variable quantities of the sulphidcs of iron, lead and zinc. The following figures, giving the analyses of the ore before milling, and of the tailings after milling, which constituted the material to be cyanided, are based on the daily samples taken during February and March, 1901.

Jan 1, 1902

By W. M. Courtis

In compliance with the suggestion in Mr. Emmons's paper on the Genesis of Certain Ore-Deposits (Trans. xv., 125), that facts should be accumulated for study and future compilation, I wish to put on record, before the data are lost, a section of the Animikie series of rocks and the vein-phenomena exposed by the explorations at the Duncan mine, Port Arthur, Thunder Bay, Lake Superior. This may serve as a supplement to my paper on this district (Trans. v., 473). I trust this information will not be without interest at. the present time. The recent discoveries of very rich silver-ores at Rabbit and Silver Mountains, on the same belt, have brought the district once more before the public; and a study of the facts here set forth may assist some fellow-engineer in the determination of the value of property offered for sale in this neighborhood. The vein at the Duncan mine was tested to a depth of over eight hundred feet by shaft and drifts, and to nearly a thousand feet with

Jan 1, 1887

By R. F. Hewlett

All ore reserve estimates are based on some system for assigning an area of influence to each drill hole. Commonly used methods of calculation are the polygonal, triangular, statistical analysis, and cross-sectional. Each of these methods is based on different volumetric considerations and the weighting of grade with tonnage varies with each method. Because the characteristics of each mineral deposit are different, a preliminary survey of these characteristics should be made for each individual deposit to determine which method or methods should be used. In this project the several methods were not only compared with one another, but also against actual production records. Basic data was derived from a mined out portion of the Silver Bell pit near Tucson, Ariz. All calculation was carried out on a digital computer, and the first step was development of computer programs which would yield the desired information. The second step was the coding of input data into punched card form. Cost and speed of computer operation were measured, and these results are given with the computer program summaries on page 38.

Jan 1, 1961

By D. J. Dunn, J. L. Huiatt, T. E. Norman

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrision rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in many mills probably represents less than 10% of the total loss, judging from AMAX experience and recent US Bureau of Mines (USBM) tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills. These indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and, for cast irons M7C3 carbides, produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1986

By C. O. Brawner

Simple, specific rules for achieving slope stability in open-pit mines are impossible to devise. Each pit has a different mining program and a different set of environmental conditions, and its final slope design must be based on an individual evaluation of the actual site. The overall philosophy of pit stability, however, is tending towards a limit design concept. Since slope angle has a great influence on the economics of most open-pit mines, efforts are being made to reduce the theoretical factor of safety for slope stability to very near 1.0. (Factor of safety is here defined as shear strength/shear stress on the most probable plane of failure.) Actually, where detailed, statistically significant testing has been done and a comprehensive ground control program is being instituted to warn of movement at an early stage, safety factors as low as 1.1 or 1.2 may be justified. The cost of the necessary procedures, however, is high. There are many factors that influence stability, but this article will be confined to three-rock structure, groundwater, and blasting.

Jan 8, 1969

By Stuart St. Clair

IN view of the great interest shown in the oil possibilities of Kentucky, one is impressed with the paucity of reliable literature on the oil fields of the state. A few brief reports by the Federal and State Geological Surveys are about the only reliable data available. When the estimated production figures, for 1918, are published by the U. S. Geological Survey, they will show a revival of the oil industry in the Blue Grass State during the past half decade. There will also be an increase in the production for 1919 and 1920, at least. Although as an oil-producing state Kentucky is small, compared with sonic of the other oil states, the present production and the area of undrilled proved territory is large enough to classify it as one of the important oil states of the Union. This paper will be confined to the Irvine District and the immediately adjoining areas which have been prospected with varying success. The Corniferous limestone or Irvine sand is the oil-producing formation in the area discussed.

Jan 7, 1919

By Benjamin B. Lawrence

The lease-system is the gradual result of the development of our larger producing mines throughout the State of Colorado. The operation of a mine, or group of mines, by corporations has been attended, in many cases, by disaster, owing to the difficulty of securing a fair day's work from the men employed in the mine, and the loss entailed by careless mining and sorting of high-grade ores, or by lax or inefficient management on the part of superintendents and foremen. Given, therefore, a mine that has been practically abandoned by its owner, for the reasons given, but still possessing merit, the lessee appears on the ground and secures a lease for a year, or term of years, from the owner, upon the payment of a royalty upon the gross smelter- or mill-returns of the ore which he mines. In this way many of our abandoned mines have been re-opened by the miner, who, with two or more associates, has been enabled, by careful attention, to obtain profitable results.

Jan 1, 1893

By N. B. Wittman

The working of blast-furnaces is always of interest to many members of the Institute, for which reason I present an account of the working of the furnaces of the E. and G. Brooke Iron Company, of which I have had charge for the past four years. Although there are no phenomenal runs to record, there have been long periods of satisfactory work, and also periods—altogether too long—when one of our furnaces has behaved in a way which may be described as "nagging." All the conditions were apparently normal,but only a very light burden could be carried, which of course resulted in a high fuel-consumption to the ton of iron, as well as increased cost of labor. The two active furnaces of this company have the following dimensions and equipment : No 2. No 3. Feet. Feet. Height ....55 60 Diameter at bosh,.....- 15, 16 " hearth,...... 8 74 " stock-line,..10 91/2 Height of bosh,..23 23 " tuyeres,. 5 5 Diameter of bell,.7 6 Front,....closed open Both furnaces are blown with I. P. Morris condensing-engines, sim

Jan 1, 1890

By C. B. E. Douglas

In an interesting article on evaluation of the water problem at Eureka, Nev., W. T. Stuart describes how a difficult water problem, or one phase of it, may be evaluated by means of a small scale test. Test data are plotted by a method rendering, under certain conditions, a straight-line graph that can be projected to show how much the water table will be lowered by pumping at any specified rate for a given time. A formula is then used to determine the size of opening, or extent of workings, necessary to provide sufficient inflow to enable pumping to be maintained at that rate. At first glance this might seem the answer to a miner's prayer, but a word of caution is in order. It may not be the whole answer. Moreover, results obtained by the method described are reliable only for conditions approximating those assumed. Even where conditions do not meet this requirement, however, it may be possible to draw helpful inferences from the results, perhaps enough to facilitate another approach to evaluation of a problem.

Nov 1, 1955

By Frank C. Roe

Two cogent and ubiquitous facts have supported a constant search by the ore processing industry for better wear resistant materials in equipment. First, designs and types of equipment change or improve continually to meet the economic and physical demands of different and/or leaner ores. Second, practically all equipment is subject to impact and abrasion conditions that probably are more severe and extensive than in any other industry. Development and testing by operators and equipment manufacturers alike, has produced an extensive variety of longer lasting metal alloys, rubber, plastics, ceramics and other materials to improve equipment performance under different specific conditions. The need for diversified materials becomes obvious upon the simple realization that no two beneficiation operations are identical. Among the variables in the handling of ore are: 1. Size and weight of ore particles. 2. Hardness and sharpness of ore particles. 3. Concentration of ore particles in liquid or gas suspension. 4. Velocity and direction of particle impact toward equipment surface. 5. Coefficient of friction between ore particles and equipment surface. 6. Temperature of operation. 7. Chemical environment of operation.

Jan 12, 1967

By Rip Thompson

ALTHOUGH the metallurgical treatment for the Ophir Hill tailings was developed more than 20 years ago and in the interim a vast amount of experimental work was done with later-developed flotation rea-gents, it was found necessary to revert to the original oil reagents and their combina-tions with specific chemical reagents in order to obtain results of economic value. This is of especial interest because in present ore-treatment investigations later-developed flotation reagents are used almost exclusively and the coal-tar deriva-tives, except in certain patented reagents, are virtually neglected. These coal-tar oils and derivatives still have a definite field of application, especially in the treatment of some oxidized ores when modified sulphidi-zation is desirable. The Ophir Hill tailings deposit is in Ophir Canyon, Tooele County, Utah, about 55 miles southwest of Salt Lake City and 25 miles south of the Tooele smelter of the International Smelting and Refining Co. A road good for trucks leads directly from the Ophir mill to the smelter.

Jan 1, 1940