Search Documents

By David V. Ragone, Richard E. Balzhiser

The liquidus uranium concentration in the U-Bi system is given by the following expression for the temperature range 400° to 800°C: No break was observed in the curve over this temperature range. The partial molar enthalpy change for uranium in the liquidus reaction, UBi2— U + 2Bi, was found to equal 12,300 cal per g mole. Copper produced a continuous decrease in the liguihs uranium concentration at 600°C. The presence of copper in the solvent was observed to affect the uranium activity coefficient according to the following expression: duced no change in the liquidus combosition below 0.6 at. pct Pd. Higher palladium concentrations sharply depressed the uranium concentration. SOLUTE behavior in molten alloys has been shown to be strongly influenced by the presence of additional species. Much attention has been given to such phenomena in iron-base systems where a number of alloying elements and/or impurities are likely to be present in small but significant quantities. Frequently, the interaction of these solutes has altered their thermodynamic behavior to the extent that reaction equilibra are appreciably influenced. Consequently, much of the information available for binary behavior must be reevaluated when additional components are likely to be present. Similar interactions can be expected to occur in bismuth-base solvents. Interest in the use of bismuth solutions of uranium as reactor fuels has stimulated investigators to explore the effect of various elements on the liquidus uranium concentration. Criticality requirements necessitate close control of the uranium concentration which, at the anticipated operating temperature of 500°C, approaches saturation. Consequently, elements which suppress the liquidus concentration could produce serious reactivity problems. Since the fuel solution is cer- tain to contain additives, such as magnesium and zirconium, for corrosion inhibition as well as small concentrations of fission products and corrosion products, a better understanding of the possible interaction phenomena is mandatory. This need stimulated experimental programs at the Brookhaven National Laboratory and elsewhere to determine precisely the liquidus uranium concentration in the bismuth-rich portion of several ternary systems. Early experimental efforts were directed toward an accurate dcmtermination of the U-Bi liquidus over the temperature range from 300' to 800°c. As shown in Fig. 1, the results to date exhibit considerable scatter. The investigations of Bareis,' Teitel,2 Greenwood,3 and Cotterill and hon4 agreed well below 700°c. Greenwood and Teitel extended their studies to higher temperatures but failed to concur in their results. A more recent study by Schweitzer and weekss at Brookhaven National Laboratory between 300' and 725°c, produced values 15 pct lower

Jan 1, 1962

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,' it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By E. F. Burch, R. W. Schoenberger

This paper deals with an investigation of the use of steam filtration for filter cake dewatering and shows that it may be applied on a practical scale. The advent of larger quantities of minus 1/4 in. coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content. A lowering of the surface tension within the limits of normal wetting agent dosage results in a rather insignificant decrease in cake moisture content. Not until the dosage is increased to a point well beyond this limit is there an appreciable decrease in moisture. At these high dosage levels, interfacial tension is a major factor contributing to the appreciable moisture reduction obtained. Since no suitable method has been developed to recover and recycle this wetting agent, this phenomena is not of practical significance. On the other hand, a reduction in liquid viscosity has a pronounced effect on cake moisture. While it is readily apparent that one method of reducing liquid viscosity is to heat the entire feed slurry, it is equally apparent that this would not be an economic approach except, perhaps, in certain isolated cases. It does, however, suggest that water circuits should be designed to conserve heat as much as possible and to make use of any waste heat that may be available. The use of hot air as a heat carrying medium for drying porous materials on a filter has been practiced for many years. However, this method is restricted to materials with a high air rate in the order of 100 cfm/ ft2 because of the low heat release per unit weight of air passing through the cake. The normal fine coal filter cake has an air porosity far too low to make this a practical approach. Various types of radiant heating devices have been investigated and can significantly lower moisture content at reasonable thermal efficiency. However,

Jan 1, 1964

By E. P. Barrett, T. L. Joseph

The large iron-ore producers on the Mesabi Range are able to maintain the silica in their shipping products at from 8 to 10 per cent. by mixing ores of various grades, some assaying 4 per cent, silica and some as high as 18 per cent. silica. For each ton of 4 per cent. silica ore mined, a ton of 14 per cent, silica ore can be mined and mixed with it and the average grade maintained at 9 per cent. This mixing operation has made possible the utilization of large quantities of ore too lean to be used alone, and herein lies the advantage of the producers who operate a number of mines at the same time. As the grade of the ore from one of the properties falls off, a little high-grade ore from another property can be mixed with it and the average maintained, while if one property alone were being operated all of the ore below grade would be left behind. This mixing operation, however, can continue only as long as there is high-grade ore available for mixing with the high-silica ores and, while the tonnage of iron ore in the Mesabi Range is still enormous, the tonnage of high-grade ore suitable for mixing with any quantity of low-grade ore is being rapidly depleted. Obviously, if an 18 per cent. silica ore can be reduced by concentration methods to 12 per cent. silica, considerably more of it can be utilized with a given amount of high-grade ore. The operators on the Mesabi Range recognize this situation and are energeticdly endeavoring to reduce the silica in their concentration plants because every unit of silica that can be removed by concentration is a conservation of their high-grade ores. More Elaborate Processes Will Be Needed At the present time there are thirty-seven concentrating plants on the Mesabi Range, and about one-third of the total ore shipped is beneficiated in these plants. In about one-half of these plants no reduction is made in the silica but the moisture or structure of the ore is improved. The washing process is by far the most important method for the removal of silica, and it is interesting to observe that the tonnage of "wash" ore during the past five years has shown practically no increase although the total tonnage of ore shipped has increased. This is due to the fact that the available tonnage of wash ore is being depleted and the amount

Jan 1, 1930

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By J. F. Wilson

Steady-state flow theory, previously applied to displacements with two mobile phases, is extended to cover down-structure flow involving three mobile phases: oil, gas and water. When used with normal reservoir fluid properties, the theory predicts the existence of four distinct flow regimes and the conditions under which each regime exists. The predicted behavior is verified by a parallel-plate model study. INTRODUCTION Special problems exist when a water flood is contemplated in a dipping reservoir having a substantial gas cap. Normally, the gas-cap region is one of very low oil saturation. If oil is moved into the gas cap during the flood, a loss in recovery results. Efficient recovery of the oil underlying the gas is therefore difficult. In two reported field water floods, injection into the gas cap has been used to solve these problems. At the West Norfolk Garr Sand Unit, injection into the upstructure region of the reservoir was made for the stated purpose of filling up the gas cap with water.' The purpose in the Sholem Alechem Fault Block "A" Sims Sand Unit was to form a continuous water barrier between the gas cap and oil band.' A laboratory model study preceded this flood and was described in the same publication. Both of these gas-cap water injections gave satisfactory results, but the published data are insufficient to allow generalizing to other field conditions. The present investigation was also undertaken to obtain results for a specific field problem. However, these results will be shown to be in agreement with an extension of the Dietz3-5 mathematical model to three-phase flowing systems. The agreement between the theory and the model studies indicates that the mathematical model can be used to describe completely the flowing system under some conditions, and to indicate the general type of flow to be expected under all conditions. FLOW THEORY The Dietz equations for two-phase flow are derived "' for the case of constant-velocity linear flow in a homog- eneous porous medium. The transition zone between the fluids is assumed to be of negligible extent so that the displaced and displacing fluids are separated by a sharply defined interface, as illustrated in Fig. 1. The density and mobility of the displacing fluid are constant over the region behind the interface, and the same properties of the displaced fluid are constant over the region ahead of the interface. To extend the Dietz equations to three-phase systems, we postulate the flowing system shown in Fig. 2 and determine the conditions under which it can exist. The

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Charles A. Ashburner

VERY little is known of the economical value of the coal-betas of. the State of Texas. The first authentic statement in regard to their occurrence is that contained in the reports of the United States Explorations for the Pacific Railroad, near the 32d parallel of latitude, published in 1853-55. Professor William P. Blake reports, "that a number of seams of bituminous coal, varying, in thickness from two to four feet, have been opened along the Brazos River, in Young County, about one hundred and fifty miles west of Fort North." Dr: Shumard also states, "that the characteristic fossil forms of the Carboniferous Era have been found with this coal, and considers the ago of the formation established. Fossils obtained from the carboniferous limestone remove all doubt of the age of these deposits."† In the spring of 1879, I was called upon by. some Eastern capitalists to make an examination of the Brazos coal-field, in order to obtain the thickness, extent, and value of the coal which could be mined and be- made merchantable for steam, heating, and metallurgical purposes. The demand for coal in this section of the country is great, and a fuel. which in our Eastern markets might be considered of inferior quality, would here find a ready sale. It must be remembered that the market value of a coal does not depend upon its absolute purity, but upon its actual value in heat units which it is capable of producing. A poor coal which can be cheaply mined near the: consumer, is infinitely more remunerative to a mining company than a superior coal whose cost to the consumer is greatly increased by high mining charges and railroad freights. The value of the Texan coals does not depend upon their purity but upon their low first cost and nearness to a market. A glance at a geological map of the United States, will show that the Brazos coal-field is the extreme southwestern extension of what may be called the Missourian, Fourth or Western, bituminous coal * I am permitted by the gentlemen for whom the examination was made to publish the general statements contained in this paper. † Macfarlane's Coal Regions of America. More recently brief mention has been made of the coal-field in the pamphlets of the State geological survey. These reports are, however, too general, too indefinite, and too impracticable to permit of any conclusions as to the value of the coal as an economical, merchantable fuel.

Jan 1, 1881

By Y. L. Yao

It is suggested that the binary alloy systems of transition metals may be classified into groups according to "excess energy"E. For systems with positive ?E, the Laves phase, the TiNi3-, the TiCu3- and the Cudu-type rich in the smaller atom and the TizNi-type rich in the larger atom may exist. For systems with negative ?E and composed of two components of different crystal structures, the X, the Cr3O and the phase may exist on the side of the phase digrattz rich in the component with the higher "solubility factor" value am! the Cudu-type and the disordered hcp phase on the other side; if the crystal structure of two components is the same, the Cudu-type may exist on both sides. For systems with weakly positive ?E and cotnposed of different crystal structures, the u phase and the MgCd3-type may replace the Laves phase and the other types; the X, the Cr3O and the a phase may also exist. Finally, the equirnolar compounds of the CuAu- and the CsC1-type may exist irrespective of the sign of ?E. THERE are many factors which play a major role in the formation of binary intermediate phases in alloys, such as the crystal structure, the electronic structure, the atomic size and the electrochemical factor. To find the simultaneous effects of all these factors on the formation of intermediate phases of every metal would be a difficult task, especially because only a small fraction of experimental facts necessary for the complete formulation is known at present. Thus the past surveys of intermediate phases have been usually confined to few metals, several types of intermediate phases and some but not all controlling factors. In a previous paper1 the idea of "solubility factor" of metals was introduced. Although the suggested values are tentative and empirical, the formation of a continuous series of solid solutions in metals could be correlated with the interplay among the atomic size factor, the solubility factor and the crystal structure factor. The purpose of this paper is to demonstrate qualitatively the interplay of these factors in the formation of binary intermediate phases among transition metals. FACTORS CONSIDERED The Crystal Structure Factor. With rare earths excluded, the transition metals are classified into three common crystal structures listed in Table I. There is arbitrariness in the present classification of several allotropic elements. However, out of seventy-odd continuous solid solutions formed among transition metals, only six of them, namely, those

Jan 1, 1962

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart's paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R's, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.'s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart's results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By R. S. Shoemaker, F. W. McQuiston

RECOVERY METHODS AS RELATED TO PROPERTIES OF SILVER ORES The earliest metallurgical process for treating silver ores was amalgamation with mercury which was in use in the early 1500's. Closely following was the development of the Patio process for treating ores at Pachuca, Mexico. Silver often occurs as the native metal and in deposits associated with other metals such as gold, copper, lead and zinc. Principal silver minerals include compounds of sulfur, antimony, arsenic, and copper. Silver chloride, and argentiferous galena are also prime sources. Native silver and the chloride characterize the oxide zone of most deposits. Native silver can be concentrated, amalgamated, or cyanided. Silver chloride rapidly dissolves in cyanide without oxygen. Oxidized silver ores containing the higher oxides of manganese are generally refractory to metallurgical treatment. A refractory compound of manganese and silver is formed, probably a manganite , which is insoluble in cyanide solutions. Argentite is the predominant silver mineral. Other important economic minerals are native silver, argentiferous galena, cerargyrite, pyrargyrite and tetrahedrite. Argentite dissolves slowly, the reaction being reversible requires an excess of cyanide. Argentite with disseminated fine grained gold occurring in quartz veins with minor amounts of chalcopyrite and galena may be cyanided directly after grinding, with high silver and gold recoveries. The flowsheet adapted to this type of ore is the Minas de San Luis, Tayoltita cyanide plant, which treats a high grade argentite silver ore containing gold. It is a standard cyanidation circuit but employs long periods of agitation contact for the high silver sulfide content ore. Lead-zinc base metal semi-oxidized- complex ores in pipes and chimneys are replacement deposits in limestone at El Mochito Mine, Honduras. Mineralization comprises galena, cerussite, anglesite, sphalerite, calamine, and smithsonite. The silver content of about 16 ounces occurs as native silver globs, wire and the mineral argentite. After flotation of lead and zinc concentrates, the tailings are cyanided for gold and silver recovery. The great Huelva pyritic copper deposits of Spain carry a little gold and silver. At Cerro Colorado, these metals were concentrated above the chalcocite zone into the so-labeled Mgossanu. This material with a content of 0.08-0.09 oz Au and 1.50 oz Ag per ton is amenable to cyanidation. See Cerro Colorado flowsheet. In southern Hidalgo, about 60 miles north of Mexico City, are the great silver--gold veins of one of the foremost silver mining districts of the world. Real del Monte, Pachuca. The mineralized area consists of flow rocks and intrusives. The oxidized ores carry pyrites with oxides of iron and manganese and other minerals, silver and gold. The first zone contains

Jan 1, 1975

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By M. Cohen, S. A. Kulin

AT a recent symposium on thermodynamics in physical metallurgy1 two opposing theories of the austenite-martensite transformation were presented. Both theories agreed that this type of reaction involves a nucleation process which requires activation and that the activated nuclei develop into the well-known martensite plates with tremendous speed. However, there were essential differences in the two points of view concerning the nature of the nucleus and the mechanism by which the nucleus propagates. According to Cohen, Machlin, and Paranjpe,' the nucleus is a strain center with sufficient elastic energy to initiate a cooperative displacement among the atoms of the parent phase when a sufficiently low temperature is reached. This displacement propagates as a wave in shear-like fashion to transform the austenite into martensite without benefit of diffusion. On the other hand, Fisher, Hollomon, and Turnbull3 regard the nucleus as a solute-poor region (in the austenite) of a size which becomes supercritical relative to coherent growth into martensite when an appropriately low temperature is reached. This growth process is taken to be an atom-by- atom transfer from the receding austenite lattice to the advancing martensite lattice through the coherent interface that exists between the two phases. The present paper is not conceded with the divergent views as to the nature of the nucleus but describes some critical experiments which differentiate between the two proposed mechanisms of propagation. Fisher' has summarized the latter issue in the following way: According to the cooperative displacement theory, the speed of formation of mar-tensite plates should not be decreased by lowering the temperature, and martensite should form with extreme rapidity at very low temperatures; whereas with the alternate growth process, the speed of the martensite transformation should be retarded at very low temperatures, decreasing to zero at the absolute zero. The atom-by-atom growth mechanism predicts a marked slowing down of the reaction rate with decreasing temperature because the rate of self-diffusion in the austenite is involved in this picture. For example, Fisher, Hollomon and Turn-bull5 estimate that the activation energy for this growth process in steel is (0.34)2(0.36)* times the activation energy for self-diffusion in y-iron. The two most recent determinations of the latter quantity are 67,900" and 74,2007 cal/mol, which may be averaged as 71,000 cal/mol. This, in turn, gives a value of 3000 cal/mol for the activation energy of the atom-by-atom process, and hence the rate of growth should vary as e 8,000/RT where R is the gas constant

Jan 1, 1951

By B. A. Cheadle, C. E. Ells

The ovienlalion of hexagonal a-zirconium crystals in cold-drawn Zircaloy-2 tubes and in both as-extruded and heat-treated Zr-2.5 wt pcl ND tubes has been rrleasured using the inverse Pole - figure technique. Uniaxial tensile tests hare shown the Zil-caloy-2 lubes to hare highly anisotropic delovmation behavior whereas heat-treated Zr-2.5 wt pet Nb tubes are nearly isotropic. The differences in deformation behavior are esbloilred from the observed textures of the tubes and the deformation systems known to oberate in Zircnloy,-3. Tlze vcsults lead to an explanation of the high effective strain observed fov the Zircaloy-2 tubes as colrzpared to heat-treated Zr-2.5 wt pet Nb tubes in restrained end burst tests at 280° to 300°C. THE Zr-2.5 wt pct Nb alloy. when heat-treated by quenching from temperatures slightly below the (a + p)/P phase boundary and subsequently aged at 500°C, has tensile strengths about 50 pct greater than those of 20 pct cold-worked Zircaloy-2.1 There is. therefore, considerable economic incentive to replace Zircaloy-2 with the heat-treated alloy in some in-reactor applications. notably for pressure tubes, where strength is a prime consideration. However, when tubes of Zr-2.5 wt pct Nb fabricated by extrusion and drawing prior to heat treatment were subjected to restrained end-burst tests at 300 °C. the circumferential expansion at failure1 was only 10 pct that of cold-drawn Zircaloy-2 tubes in similar tests,2 Table I. This result was not predicted from uniaxial tensile tests in which the ductilities of the two materials were quite similar.' The detailed requirement for ductility in pressure vessels has not yet been worked out. and comparison of the relative merits of cold-worked Zircaloy-2 and heat-treated Zr-2.5 wt pct Nb is further complicated by the irradiation-induced loss of ductility and hydrogen pickup each will undergo from reactor operation.1,2 Nevertheless. the lower circumferential expansion of the Zr-2.5 wt pct Nb tubes raised serious doubts on the advisability of their use as pressure vessels. For this reason, an investigation to determine the cause for different ductilities of the two types of tubes was initiated. From a study of uniaxial tensile properties and crystallographic orientation it has been found that the fracture ductilities observed in the burst tests can be related directly to the crystallographic ori-

Jan 1, 1965

By Gustav S. Preller, A. M. Gaudin

Fox the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were-limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2 -4 and has now received confirmation as to accuracy by an entirely independent method.5 This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8Å2. or 16.2Å2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8Å2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura's results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2Å2., with extreme values at 13.7 and 16.9Å2. The average of 21 determinations made in connection with this study' gave a parking area of 14.3 ± 0.27Å2. In view of this result and of the Harkins and Jura

Jan 1, 1946

By A. M. Gaudin, F. W. Bowdish

MINERAL dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,7 its magnetic remanence,3 the turbidity of its suspension,8 and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid-both internal and external-the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample .2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. APPARATUS In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. 1 and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1944

By P. R. Kalischer

In the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more cornponents that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measuremerits and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. Nature and Removal of Surface Barriers The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 Per cent Fe, So Per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However. this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941