Search Documents

By A. B. Young

In the original design of the flue system, the flues from the roasters delivered their gases to a large brick dust chamber which discharged into another flue with stack connection, as shown in Fig. 1. The treater is so situated that the gases are taken by it directly from the chamber and discharged again into the flue. The complete installation comprises two treater units, only one of which has been installed at present. The treater is essentially a flue 1.0 ft. high, 12 ft. wide, and 61 ft. long. (3 by 3.6 by 18.5 m.). Suspended inside, vertically and running lengthwise, are four banks of No. 20 corrugated iron plates; each bank is 10 ft. long, making an effective treater length of 40 ft. The spacing from center to center of the rows of plat,es is 9 1/8 in. (23 cm.) giving six-

Jan 1, 1921

By M. L. Requa

In the fall of 1910, the Nevada Petroleum Co., operating in the Coal-inga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.—a record obviously far beyond that made in 1910 by the Nevada Petroleum Co. The records herewith are published with the hope that some one having more recent data will publish them so that comparison may be

Jan 1, 1915

By Arthur H. Redfield

The West Indies are the summits of a submerged mountain chain, the continuation of which must be sought in the mountains of central Honduras. In Haiti, the chain divides, one branch passing through Jamaica and the other through Cuba, the Cayman Islands, and the Misteriosa bank. Suess divides the West Indies into three zones: The first zone is entirely of volcanic origin and includes many recent volcanic cones. It includes the arcuate string of islands, which extends from Saba and St. Kitts to the Grenadines and Grenada. The western half of Guadeloupe belongs to this group. The second zone consists of a geanticline, of which the sedimentary rocks range from the Jurassic to the Quaternary, but consist chiefly of Lower Tertiary sediments. In the west it is broad, including the whole of the Greater Antilles; but in the east it is restricted to a narrow belt, which includes the Virgin Islands (except Anegada), Anguilla, St. Bartholomew, Antigua, the eastern part of Guadeloupe and part of Barbados. The islands that compose the third zone are flat and low. Like the second, this zone is broad in the west and narrow in the east; it includes the Bahamas, Anegada, Sombrero, Barbuda, and part of Barbados. Geologically, Florida and the plain of Yucatan may be regarded as belonging to it. Trinidad and Tobago, though geographically adjacent to the Lesser Antilles, are geologically a detached part of the South American continent. The crystalline complexes of northern Trinidad and of Barbados are a continuation, en echelon, of the crystalline axis of the promontory of Paria. The folded Cretaceous and Tertiary of the central and southern parts of Trinidad represent a continuation of the folded sedinlents of the Paria district of Venezuela. Possible Oil-bearing Areas The volcanic islands of the inner arc of the Lesser Antilles may be excluded from consideration; these include Saba, St. Kitts, Nevis,

Jan 1, 1923

By T. F. Witherbee

Success in this operation is much promoted by adhering to a definite plan. Random work is of little account. In general, anything done that will enable the blast to pass through the obstruction, providing the melted products can be got away from the tuyeres, is all that is necessary. Hence the utility of high explosives in breaking up the chilled mass in the hearth. (This, by the way, should be done with the wind on, so as to prevent the filling of the tuyeres with the usual rush of cinder following the explosion.) If from any cause it is not expedient to use explosives, the simple but very effective instrument known as the kerosene or hydro-carbon blow-pipe can be depended upon to perforate the contents of a blastfurnace hearth to any extent required. It consists, as used in the Champlain district (first by Mr. Charles H. Foote), of several pieces of gas-pipe, liberally supplied with elbows (five in number) so as to be flexible; one end being connected to a tuyere-stock and the other brought to bear upon the place to be melted out. A 1/4-inch pipe leads from the last length, or blow-pipe proper, to a reservoir of kerosene or crude oil, set high enough to overcome the blast-pressure, This 1/4-inch pipe should have a valve conveniently located to regulate the flow of oil, and also another next to the reservoir. With a good hot blast and a surprisingly small quantity of oil, this apparatus will melt, burn or mechanically dislodge anything around a blast-furnace hearth excepting firebrick and water-cooled castings or plates. It may be helped by vigorous prodding with a suitable steel bar, to detach the fused but sometimes sticky material. A very good way to operate on a chilled hearth with it, is to open up a hole from a cinder- or iron-notch to the nose of the most convenient tuyere and then make a blow-pipe of the tuyere by turning

Jan 1, 1885

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By Francis A. Thomson

But little has been written concerning the camp of Republic. In 1900 Chatard and Whitehead 1 reported the results of some experiments with samples of ore from the Republic mine, and a few years later Fritz Cirkel2 described the construction, operation, and results attained in the mill at the Mountain Lion mine. From time to time brief articles, mostly of a semi-technical nature, have appeared in the Engineering and Mining Journal and other mining periodicals. The general geology of the camp, especially in regard.to its areal features, has recently been ably described by Joseph B. Umpleby.3 To bring to mind the general features of the district it may perhaps be well to review briefly some facts in regard to it, before discussing the treatment of the ore. I. History and Production. The town of Republic is situated in the NW. corner of Ferry county, about 25 miles south of the International Boundary, on the head-waters of the San Poi1 river, in what was formerly the " north-half" of the Colville Indian reservation. On Washington's birthday, 1896, this portion of the reservation was thrown open to mineral location, and within a few weeks important discoveries had been made. The present Eureka mining-district was organized, the camp grew apace, and consignments of ore were shipped by wagon to Grand Forks, 30 miles away; or to Marcus, a somewhat greater distance. It is reported that the first 1,500 tons shipped from the Republic mine uetted the owners $160 per ton, after being hauled

Jan 1, 1913

By C. L. Dake

Residual deposits occur both as products of weathering and as products of hydrothermal decay. Products of Weathering That climatic conditions affect greatly both the rate and the results of weathering, is shown in temperate, polar, arid, and tropical regions, each of which will be considered separately. Weathering under Temperate Climates The decomposition of any rock is accomplished by the removal of the more soluble bases, and a concentration of the relatively insoluble oxides of iron, aluminum, and silicon. By reason of its somewhat greater solubility, silica is much more subject to removal than iron and alumina. The two important residual end products of weathering are sands and clays, the former consisting essentially of quartz, and the latter of kaolin and limonite.l When such deposits are formed in situ, the sands and clays are not separated, but remain as mixtures, which can be more or less perfectly separated by treatment with water. In such a separation, the ferric oxide or hydrate tends, by reason of its fine state of division, to remain with the clays and silts rather than the sands. While ferruginous sandstones are everywhere common, they are rarely rich enough in iron to become an ore without secondary concentration. Since the silica of these sandstones is completely crystalline quartz, it is much less liable to removal by solution than are the more soluble forms of partly amorphous chert and jasper, which have been removed on so large a scale from the Lake Superior iron formations.2 Moreover, the iron cement of sandstones, which constitutes the chief iron content of these rocks, is often a result of later infiltration, and not of original sedimentation. Thus if clays rather than sands contain the iron of residual decay,

Jan 1, 1916

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By J. Parke Channing

The Miami orebody occurs in an altered Pinal schist. It is popularly known as one of the '(porphyry " deposits but, as at Inspiration and Ray, the ore is an altered mincralized Pinal schist. The orebody mined is the zone of secondary enrichment. Speaking in general terms, the area of the orebody at Miami may be considered as 1000 ft. long and 800 ft. wide. The vertical thickness varies from 200 to 400 ft., so that it is an extremely irregular mass. The study of the ground movement and resulting subsidence at Miami is complicated by the fact that the formation is not homogeneous throughout the mining area, the orebody terminating on its eastern extremity at a fault plane adjoining the Gila conglomerate. This conglomerate is a recent sedimentary deposit somewhat analogous to glacial drift and consists of boulders of granite, schist, and other material cemented with clay, and at times is quite hard. The fault dips eastward at an angle of 45". The original method of mining was top slicing, the slices being 10 ft. thick. At first, there was a good deal of experimenting with mining methods. Some undercut rooms were tried, and the stopes were filled with broken ore with the idea of removing intervening pillars by top slicing. The adoption of the top-slicing method in itself involved considerable experimenting, including some experiments with a long-wall system. The method finally adopted involved the operation of top slicing areas 250 ft. square, each with a central supply raise and ore-gathering raises, each block being worked as a unit. Mining operations in the Captain orebody, which connects with the boundary of the Inspiration property, were started by the room-and-pillar system, the rooms extending across the orebody, with widths of 10 to 15 ft., with 15- to 10-ft. pillars between. The intent was to operate the rooms as shrinkage stopes, permitting the pillars to crush when the ore was drawn from the rooms. It was found that the shrinkage stoping was unnecessary, so a system of block caving was adopted. This system was so successful in the Captain orebody that, about three years ago, the method of mining in the orebody was changed from top slicing to block caving, the method now in use. The block caving system, as practiced

Jan 1, 1923

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By J. Parke Channing

The Miami orebody occurs in an altered Pinal schist. It is popularly known as one of the &apos;(porphyry " deposits but, as at Inspiration and Ray, the ore is an altered mincralized Pinal schist. The orebody mined is the zone of secondary enrichment. Speaking in general terms, the area of the orebody at Miami may be considered as 1000 ft. long and 800 ft. wide. The vertical thickness varies from 200 to 400 ft., so that it is an extremely irregular mass. The study of the ground movement and resulting subsidence at Miami is complicated by the fact that the formation is not homogeneous throughout the mining area, the orebody terminating on its eastern extremity at a fault plane adjoining the Gila conglomerate. This conglomerate is a recent sedimentary deposit somewhat analogous to glacial drift and consists of boulders of granite, schist, and other material cemented with clay, and at times is quite hard. The fault dips eastward at an angle of 45". The original method of mining was top slicing, the slices being 10 ft. thick. At first, there was a good deal of experimenting with mining methods. Some undercut rooms were tried, and the stopes were filled with broken ore with the idea of removing intervening pillars by top slicing. The adoption of the top-slicing method in itself involved considerable experimenting, including some experiments with a long-wall system. The method finally adopted involved the operation of top slicing areas 250 ft. square, each with a central supply raise and ore-gathering raises, each block being worked as a unit. Mining operations in the Captain orebody, which connects with the boundary of the Inspiration property, were started by the room-and-pillar system, the rooms extending across the orebody, with widths of 10 to 15 ft., with 15- to 10-ft. pillars between. The intent was to operate the rooms as shrinkage stopes, permitting the pillars to crush when the ore was drawn from the rooms. It was found that the shrinkage stoping was unnecessary, so a system of block caving was adopted. This system was so successful in the Captain orebody that, about three years ago, the method of mining in the orebody was changed from top slicing to block caving, the method now in use. The block caving system, as practiced

Jan 1, 1923

By Franklin R. Carpenter

In area, the Black Hills are about equal to the State of Connecticut. As the accompanying geological map indicates, they exhibit in the main a simple structure, presenting a central mass of granite and Archæan rocks, on all sides of which the later sedimentary rocks dip

Jan 1, 1889

Canada&apos;s newest low-grade porphyry copper mine, Gibralter Mines Ltd. (N.P.L.), has reached production. The subsidiary of Placer Development Ltd., located at Williams Lake in the Caraboo District of central British Columbia, began open pit mining in mid-June on reserves estimated at 358 million tons assaying 0.373r: Cu and 0.016C; MoS,. Each of four separate zones will be mined in a predetermined sequence, in one or more stages, and with a throughput of more than 36,000 tpd. The sequence and stages of mining the zones have been determined by computer calculation and economic analysis and are designed to maximize recovery and minimize cost. At the very least, the mine is off to a promising start. Development costs leveled off at $67 million. 9&apos;; below the anticipated budget.

Jan 7, 1972

By Charles Legrand

In many iron, coal and copper mines where large tonnages are known before starting operation and proper provisions can be made, the problems of electric traction by trolley locomotives are not very different from those of surface plants. In such installations the gauge of the track, the radius of curves, and the clearances, both vertical and horizontal, can be made to suit the conditions of the traffic. It is more difficult to install electric traction in mines which were started with hand tramming and where no consideration was given to the possibility of mechanical traction being used. The writer having had some experience in the installation of electric traction in copper mines, the following remarks apply more particularly to these mines. With the gauge of track usually 18 or 20 in., the weight limit of locomotives obtainable from manufacturers in this country varies from 3 to 6 tons. The full-load speed varies from 49 to 6 miles per hour. These locomotives, being made to run on very small radius curves, have a short wheel base and a long overhang from axle to coupling, which necessitates a coupling&apos; with a good deal of lateral motion to avoid derailing the cars on sharp curves, especially if couplings are of the standard railroad automatic type. Although 3-ton locomotives will run on 12- or 16-lb. rails, it has been found more satisfactory to use 25-lb. rails, as the track keeps in much better shape, it is easier to maintain the bonding in good order, and fewer derailments from dirt on the track occur with the larger rails. Where 6-ton locomotives are used the 25-lb. rails are satisfactory, but 40-lb. rails have proved cheaper where the traffic is heavy and the ground is soft, as the track maintenance is considerably lower with the heavy rails. The locomotives will run on 15-ft. radius curves, but on through runs it is advisable not to go below 40-ft. radius. The voltage used should not exceed 250 to 275 volts, and the trolley wire should be protected, to prevent accidental contacts, in front of chutes and at all points where it is low. With the air lacking somewhat in oxygen and the heat and high humidity prevalent in many mines, this

Jan 1, 1915

By Thomas S. Carnahan

The mining property of the Utah Copper Co. is situated in the West Mountain mining district, Salt Lake County;Utah, in the Oquirrh Range of mountains. Geology In a general way the rock formation of the district consists of a series of beds of quartzite and limestone intruded by a body of monzonite porphyry roughly elliptical in shape, with an east-west axis over a mile in length and a north-south axis of about 3,000 ft. This porphyry intrusion, accompanied by strong mineralizing action and fracturing, resulted in the formation of orebodies in the adjacent sedimentary rocks, and was itself sufficiently mineralized to make it one vast orebody. The Utah Copper Co.&apos;s mining property comprises within its boundaries practically the entire outcrop of the monzonite mass, of a commercial grade. Genesis of Porphyry Ore Following an intricate system of fracturing, mineral solutions circulated freely through the porphyry, depositing small quantities of copper and iron, and resulting in a considerable silicification of the monzonite. The quantity of copper originally deposited was undoubtedly too small to have ever given the porphyry a commercial value, had not secondary enrichment, due to the leaching of the copper from the surface of the mass and re-deposition in the sulphide zone, been active over a long period of years. A large portion of the leached material has probably been removed by erosion, but there still remains a blanket of leached and oxidized porphyry of varying thickness covering the sulphide ore, known as capping. Over certain sections of the orebody, this capping contains commercial quantities of copper carbonates, but most of it contains little or no copper.

Jan 1, 1916

By H. M. Howe, E. C. Groesbeck

That the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First, each particle of any composite liquid, whether it be an aqueous solution or a molten metal, in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the existing temperature, and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already solidified; A, Fig. 1. The other part is fusible at the existing temperature and hence remains molten. In the case of carbon steel, the part of each drop which actually solidifies is poorer in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying half-drop enriches the other half-drop in carbon, and thus makes it unfreezable at the existing tern- By this mechanism there arises during solidification a "littoral" or shore layer of liquid B, Fig. 1, bathing the already solidified walls, and more fusible than either those walls or the great remaining central mass of liquid or " deep sea " C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal could get past this littoral layer and come into contact with the solid walls, it would in turn solidify, and like its predecessors would split up in solidifying into a less fusible half-drop which would attach itself to those . walls and a more fusible one which would remain molten. Thus we see

Jan 1, 1920

By George I. Adams

Peru is divided into three regions—the coast, the ~ierra, or high mountainous region, and the " montaiia," or forest region of the Amazon basin. The Coast.—The coast is an arid region. No rain falls excepting in the extreme northern part, which borders the Gulf of Guayaquil. There is, however, a slight precipitation in the form of mist (gcirua), which occurs on the coast hills during the so-called winter months. The aridity of the coast is due principally to the antarctic, or Humboldt, ocean-current, which, being cold and having a temperature lower than that of the land, absorbs rather than produces vapors. The coast mists occur during the season when the land is relatively cold. N ear the Gulf of Guayaquil the antarctic current diverges from the coast, so that in the Tumbes valley and adjacent country the conditions in the summer months are such as prodnce rains. In the remaining valleys of the coast, agriculture is made possible only by means of irrigation, and is accordingly very limited in extent, although rich and varied. In the northern and south-central portions of the coast, plains extend inland from the sea, while in the southern part there is a coastal plain separated from the Pacific by a range of coast hills. Between the northern and south-central plains, as well as between the south-central and southern, the foothills of the sierra descend to the seacoast. The Sierra.—The sierra embraces the high land dominated by the lofty cordilleras of the Andes. In the southern part of Peru there are two cordilleras, the western and the eastern, which enter from Chile and Bolivia respectively, and inclose between them the Titicaca Lake basin. To the north of Lake Titicaca these cordilleras unite in the knot of Vilcanota, south of Cuzco. From this knot three cordilleras, known as the western, the central, and the eastern, extend to the northward, reuniting in the

Jan 1, 1909

By AIME AIME

ACCORDING to M. Perogordo y Lasso, professor in the School of Mines, College of Engineering, National University of Mexico, what is known a. the "co- operative system" was started there on Feb. 1, 1929. On Jan. 1, 1792, the Real Seminario de Mineria was opened in Mexico City and had much success. Later, the name was changed to Colegio de Mineria. When other branches of engineering were introduced it was known as the Escuela Nacional de Ingenieros, and finally, with the reorganization of the University the

Jan 1, 1929

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33&apos; API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By D. Harrington

Efficient ventilation of metal mines consists in having such complete control of air currents that there is always supplied at placcs where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet ventilation is only too frequently neglected, especial1y in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years&apos; study of miners&apos; consumption, the writer is convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 1, 1923