Search Documents

By J. W. Galpin, R. H. Allen

Controlled pre-grouting is a technique developed during a period of more than ten Years experience, in an effort to produce safer, drier and more economical mine shaft sinking. The technique involves a knowledge Of hydro-mechanics, both static and dynamic, and a series of specially formulated grout mixtures to obtain several desired results through precontrolled setting time. In general, the following procedures have been used to secure the best results in controlled pre-grouting: I. Before drilling is commenced, One Of two decisions is made: one procedure, a modified form of the Francois method, is to stage drill and grout, that is, drill a limited portion of the hole, then grout and redrill that section which has been grouted, progressing in stages until the required depth is reached. We prefer this method because no casing Or grouting packers are required in the bore hole. This eliminates the risk of losing them in the bore hole due to packer failure, which might result in the expense of drilling a new grout hole. Another feature Of this approach is that smaller drill holes may be effectively used, further reducing the costs. One drawback, however, is that because of the open and small size hole, it is impractical to attempt water draw-down tests. The second alternative is to drill the bore hole, (generally NX size), to the re-quire~ depth. he casing and grouting packer are placed in the bore hole at the lowest packer setting. A small, portable, power driven, swabbing device is used in the grouting casing to test the packer and remove mud or cuttings from the bore hole below the packer. The hydrostatic level is recorded and a close estimate or test is made of the quantity of water at each packer setting. Grouting progresses upward in a series of packer settings to the surface. Occasionally, casing is inserted in the bot-tom of the bore hole from within the mine, and water pressure and volume can be obtained in this manner. This is usually dangerous because of the unknown quantity of water. 2. The grouting, mining and geological engineers at the drill location make a detailed examination of the cores and also locate proper and firm grouting packer locations. A competent driller,s opinion should be given due consideration as to the character and condition of the bore hole. 3. Several samples of formation water

Jan 1, 1949

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

By Edward N. Trump

EXTENSIVE beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed-the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. THE TULLY PLAN In the Tully plan, the water passes down the annular space between the casing and the center -tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. THE DETROIT PLAN In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1944

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By Jerome Strauss, Carl L. Shapiro

THIS is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years,, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I INFLUENCE OF BODY-CENTERED CUBIC ELEMENTS The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tantalum) are reviewed individually. Iron-carbon-chromium System.-In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts' concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.-Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. a; these results have received general approval. Iron-carbon-molybdenum System.-In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and Reed,8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-

Jan 1, 1943

By Carl L. Shapiro, Jerome and Strauss

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Jerome and Strauss, Carl L. Shapiro

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By D. I. Bardos, F. X. Spiegel, R. K. Malik, Paul A. Beck

Study of the occurrence of elongated ß-Mn phase fields and of their direction of extension in fifteen ternary systems indicates that the ß-,mn phases formed by manganese with other transition elements and with either silicon, germanium, or tin may be considered as electron phases. In these phases the alloying behavior of silicon on the one hand and of germanium and tin on the other shows a significant difference . Formally all observations can be satisfactorily described by attributing to germanium and tin an apparent electron concentration of nine electrons per atom. This behavior may be interpreted by assuming that germanium and tin exclude itinerant electvons because of a strong repulsive potential arising fromthe requirement that their wave junctions be orthogonal to those of- the closed d shells of these atoms. The absence of a d shell in silicon allows this atom to admit itinerant d electrons. The following new ternary phases of unknown structure were identified by means of their X-vay difjraction patterns: (Mn,Co,Si)I , (Mn,Co ,Si)Y, (Mn.Co,Si)Q , (Mn ,Ni ,Si)W , and (Mn, Ti ,Si)A. The X-ray data suggest that these phases have large unit cells and that to some extent they may he related structurally to the 0 phase. The a phase and certain other phases formed by transition elements are characterized by their preferred occurrence at a constant electron concentration. AS a result, these "electron phases" have relation to electron concentration. The tendency of the B phase to form elongated phase fields in ternary systems along the directions of constant electron concentration has been previously demonstrated. The occurrence of an elongated 0-Mn phase field in the ternary system Mn-Co-Si was schematically indicated by Cherkashin et al.l0 The present study includes fifteen ternary systems, each containing in addition to manganese a second transition element from the group Ti, V, Cr, Fe, Co, Ni and one of the nontransition elements silicon, germanium, or tin. In each system the boundaries of the B-Mn phase were determined in the 900°, 950°, or 1000°C isothermal section, the temperature being dictated on the one hand by the requirement of sufficient rates of diffusion to approach equilibrium conditions in reasonably short annealing periods and on the other hand by the need to avoid as much as possible the partial melting of alloys during annealing.

Jan 1, 1967

By R. S. Christie

Reservoir pressure is the pressure at which a fluid is held in a state of equilibrium in a porous stratum. This pressure may be a result of the genesis of oil or gas and its subsequent migration into and through an adjacent porous stratum, or of hydraulic head. Reservoir pressure is an indication of the potential energy contained in the reservoir, and when it is known the engineer is in a position to use it to advantage in recovering and lifting the oil. It is important to know the pressures in any type of reservoir, but this knowledge is probably of greater value in a limestone reservoir, as at Hobbs, where producing rates or conditions may be more sensitive to changes in pressures. The Hobbs field is in east central Lea County, New Mexico. The discovery well was completed by the Midwest Refining C I. in 1928, but intensive development did not begin until after the completion by the Humble Oil and Refining Co. of No. 1-A Bowers in February, 1930. There are 143 producing wells on approximately 5500 acres. The field has not been defined to the northwest, but a projection of structural contours indicates that the productive area ultimately may cover 7500 acres. The producing horizon is the White or Crystalline lime of Permian age. The top of the lime is found at an average depth of 4000 ft. and the wells penetrate it an average distance of 200 ft. The main pay zone is an oolitic stratum about 25 ft. below the top, and varies from 2 to 15 ft. in thickness. Other porous or cavernous strata are found lower in the lime but have little saturation. The initial production varied from 100 to 25,000 bbl. per day, depending perhaps to some extent on the structural location but chiefly on the porosity of the pay. The initial gas-oil ratio varied from 325 to 16,000 cu. ft. per barrel. In wells where the top of the White lime was found below 350 ft. below sea level (Fig. 1)) the gas-oil ratio was usually less than 1500 cu. ft. per barrel, while in wells higher than 350 ft. below sea level, the ratio was usually above 2000 cu. ft. per barrel. The water table has been determined at about 620 ft. below sea level, by three wells on the west side of the field. With few exceptions, the wells have been completed with 7-in. casing cemented

Jan 1, 1932

By B. M. Harra, F. G. McCutcheon, O&apos

Until about 1930, the universal practice of horizontal-retort zinc smelters in the United States, as far as the writers are aware, was to operate the retort furnaces on a 24-hr cycle; that is, the retorts were charged in the early morning of one day, and in the early morning of the following day the residues were cleaned out, the retorts recharged, and a new cycle started. During the business depression of the early thirties, zinc production fell off to the extent that zinc smelters had idle retort capacity. Rather than continue to run some of the retort furnaces on a 24-hr cycle and shut down the remainder, a few companies decided to try out a longer cycle. Although the output of zinc per retort per day is lower, the longer cycle permits a larger charge per retort and improved zinc recovery. Advantages of the longer cycle were soon evident, and the practice spread rapidly. Various lengths of cycle were used, typical examples being 28-hr, 32-hr, 36-hr, and 48-hr. The 48-hr cycle fits in best with the standard routine of smelter practice that was built up on the basis of the 24-hr cycle; that is, the retort furnace "maneuver" always comes at the same time of day, and can be performed in the cool hours of the early morning. Under some conditions, particularly in some of the older plants, where the retorts are smaller than in newer plants, a 48-hr cycle is longer than necessary, and some intermediate length of cycle may theoretically be most economical. Use of an intermediate cycle, however, means that the maneuver comes at different times on consecutive days, and that sometimes it comes during the hottest part of the day. The work on the retort furnaces is extremely hot and arduous at best, and it is much worse, of course, if it is done during the heat of a summer day. When labor was plentiful and tractable, many plants were able to operate on cycles of intermediate length, but the workmen did not like the working hours. Under present labor conditions, it is hardly practicable to operate with a cycle of intermediate length, so the choice has narrowed down to the alternatives of 24-hr or 48-hr cycles. In any discussion of economics, too comprehensive generalization is not warranted, because local conditions affecting economics vary greatly. The best economic practice at one plant at any given time may be uneconomical at another plant, or even at the same plant at another time. To determine the length of cycle that is the better practice at a given plant at a given time requires a weighing of the advantages and disadvantages of each cycle, taking into consideration all the local conditions. some of the factors that must be considered in making the comparison are discussed briefly in the following paragraphs.

Jan 1, 1949

Jan 1, 1922

Jan 1, 1922

Jan 1, 1935

Jan 1, 1935

Jan 1, 1935

Jan 1, 1935

Jan 1, 1960

Jan 1, 1928