Search Documents

By Harrison A. Schmitt

One of the great copper-producing areas of the world is comprised of five U. S. western states and northern Sonora, Mexico. The Southwest province of this area, covering southern Arizona, south- western New Mexico, and northern Sonora, produces some 55 pct of U. S. copper output and the equivalent of 15 pct of world production. In 1956 the area produced about 550,000 tons. Tucson is approximately the center of the oval- shaped province, which measures only 300 miles on its east-west axis and about 200 miles on its short axis. Northwest of the oval, and forming a tenuous connection with the Utah and Nevada copper fields, is an important operating mine, Bagdad, and also the now inactive United Verde. Along its north- south axis, running from Globe, through Tucson, to Nogales, ten moderate to major copper properties have been discovered or revived during the past 15 years, and five of these in only the past seven years. The latter five properties lie in an area 25 miles in diameter, centering 20 miles south of Tucson. In order of discovery, or revival, they are: Banner's Mineral Hill and Daisy; Cyprus et al's Pima; Duval's Esperanza; Asarco's East Pima (now called Mission mine) ; and Lewisohn's Peach. Total tonnage is estimated at about 250 million tons averaging some 0.90 pct Cu, but ultimate production may exceed this amount since some of the reserve is open ended.

Jan 6, 1959

By W. G. Fischer, S. R. Felde

Trona ore at the Westvaco, Wyo., mine of FMC Corp. has been obtained by room-and-pillar methods since the mine began operation. The flat- lying, 10-ft thick trona (Na2CO3.NaHCO3.2H2O) is covered by 1500 ft of weak shale and sandstone, and extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly, and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs, efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early '60s forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were also seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. However, since roof control in the longwall methods appeared to be more satisfactory than that found in room-and-pillar techniques it was believed that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 4, 1966

By Ernest E. Thurlow

The western coal industry, long overshadowed by the petroleum and metallic minerals industries, has been revitalized by several new coal mining operations, with the promise that this is only the beginning of a tremendous surge in production of coal that will carry into the next century. The content of this paper is confined to the coal fields and recent developments in eastern Montana, northeastern Wyoming and western North Dakota. The area is commonly referred to as the Powder River-Fort Union region although the Powder River Basin and the Fort Union formation are separate entities and are not coextensive. Coincidentally or otherwise, the extent of the subbituminous part of the coal region coincides approximately with the Powder River Basin. Environmental considerations together with the low sulfur content of much of the western coal have triggered demand since this coal could not compete at present with eastern and midwestern coal solely on a delivered-cost-per-million-btu basis. However, increasing costs of underground mining and the comparatively thin seams of the eastern and midwestern deposits may soon bring a balance to these costs regardless of the sulfur content. Another factor which has made western coal competitive at this time is the use of the unit-trains to significantly reduce the cost of transportation. Fast loading and unloading facilities and trains of 100 cars or more in turn-around service are the keys to success in this effort.

Jan 5, 1974

By William G. Gates

INTRODUCTION The Heath Steele mine is located in the Bathurst-Newcastle area of northern New Brunswick. It is jointly owned by American Metal Climax, Inc. and the International Nickel Company of Canada who hold a 75% and 25% interest, respectively. The ore deposits of lead, zinc and copper sulphide occur in very fine grained pyrite and/or pyrrhotite masses. A consistent spatial relationship with a quartz feldspar porphyry is characteristic of these deposits and the many other similar sulphide deposits in the district. The two principal mineral assemblages of pyrite-sphalerite-galena, and pyrrhotite-chalcopyrite-pyrite, occupy characteristic positions relative to the enclosing rocks. This feature and the nature of the sulphide mineralization are described and the variations in metal content are noted .with special emphasis on the lead-zinc ore zones. The mine product ion rate is 3,000 tons per day of a mixed lead- zinc and copper ore which is extracted from the B-1 zone. The complex nature of the ores presents many metallurgical problems. Optimum metal recoveries are achieved when milll feed grades are relatively consistent and proportions of the contained metals are with in acceptable limits. Ore outlines and stoping blocks are delimited by close spaced diamond drilling. From this information it is possible to forecast the grade of any portion of a stoping block. Production from the various stopes may then be scheduled so as to achieve an acceptable mill feed grade.

Jan 1, 1970

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor.

Jan 1, 1960

By R. W. Raymond

The sudden death of Dr. Drown, on Nov. 17, 1904, brought to multitudes the pang of personal loss. Of all those who, as students at Lafayette College, the Massachusetts Institute of Technology and Lehigh University, were brought under his influence, not one can have forgotten him, and all will now acknowledge, with an unfading gratitude, what they owe in professional equipment to his wise, clear, skillful guidance, and in character to his sympathetic, stimulating personality. Outside of this wide circle, the experts of both hemispheres will lament the departure of one who, in his department of scientific investigation, both knew what work was needed, arid how to do it so that it needed not to be done again. The older members of the Amierican Institute of Mining Engineers will remember with gratitude the part he took, as Secretary from 1873 to 1884, in promoting the interest of that organization, and in shaping the plan and policy which it has followed with such noteworthy success. And, in addition to all these (though partly included among them), there are a host of friends, who can scarcely think of the public loss by reason of their own. Thomas Messenger Drown was born March 19,1842, at Philadelphia, Pa. His parents were natives of New England; and he was the youngest of their three sons. He received his preliminary education in the public schools and the High School of Philadelphia, from which he was graduated in 1859. Be-

Jan 1, 1906

By L. W. Kempf

A BALANCED system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internal stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced luring the commercial heat treatment of aluminum alloy products is the industrial use of aluminum increases, it is inevitable that products of increasingly large volume be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling at elevated temperatures is that of the, size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high

Jan 1, 1934

AIME 1953 DIRECTORY SUPPLEMENT OFFICERS AND COMMITTEES OF LOCAL SECTION; COUNCIL OF SECTION DELEGATES Linwood Thiessen, Chairman H. D. Vaughan, Vice-Chairman John H. Melvin, Secretary EXECUTIVE COMMITTEE L. E. Thelin, Connecticut J. B. Cunningham, Arizona W. L. Penick, San Francisco G. L. Yates, Kansas DELEGATES Adirondack - C. DeWitt Smith '54 Alaska - Robert 11. Chapman, ?54 Arizona J. B. Cunningham, '53 Black Hills - Sidney M. Runke, '54 Boston -R'. Schuhmann, Jr. ?54 Carlsbad Potash - W. P. Wilson, '54 Central Appalachian - Charles T. Holland, '54 Chicago - H. A. White, '54 Cleveland - Milton Tilley, '54 Colorado - J. Paul Harrison '54 Columbia - Harold Kirkemo, '54 Connecticut - Lewis E. Thelin, ?53 Dallas - Kenneth F. Anderson, '54 Delta - Roy S. Sullins '54 Detroit - F. P. Bens, '53 East Texas - Joseph A. Morris, '54 El Paso Metals - E. M. Thomas, '54 Florida - W. O. McClintock '54 Fort Worth - Ray Elner, '51 Gulf Coast - H. E. Treichler, '53 Kansas - G. L. Yates, '53 Lehigh Valley - H. R. Gault '54 Lima, Peru - R. P. Koenig, ?54 Lou-Ark - A. H. Crawford. '53 Mexico - W. G. Kane, '54 Mid-Continent - J. H. Beesley, '53 Minnesota - J. R. Stuart, '54 Montana - F. W. Strandberg, '53 Nevada - Albert Silver,'53 New York - P. Malozemoff, '54 North Pacific - A. H. Mellish, '54 North Texas - K. F. Anderson, '54 Chio Valley - J. H. Melvin, ?53 Oklahoma City - Charles Miller, '53 Oregon - T. C. Matthews, '54 Penn. Anthracite - D. C. Helms, '54

Jan 1, 1953

By Toshihisa Adachi, Shosei Serata, Shunsuke Sakurai

Many different methods of measuring the in-situ stress field have been developed in recent years. They are all based on the assumption of elasticity without allowing any viscoelastic deformation. By using the high resolution strain-measuring technique recently developed in the laboratory at Serata Geomechanics, many rocks were found to be viscoelastic. The viscoelasticity of rock media was found to be dependent upon the resolution of the strain measurement. The higher the resolution of the strain measurement, the greater number of rocks could be identified as viscoelastic. All rocks eventually exhibit viscoelastic deformation under high stresses relative to the strength of the material. Therefore, the conventional methods of elasticity become less reliable with increase of ground stress. In deep underground formations, even hard rocks become viscoelastic. At the same time, many ground formations near the surface are actually viscoelastic. A new method was developed in the laboratory to determine the in-situ stress field in viscoelastic rock media. Rocks in general exhibit a small amount of viscoelastic creep whenever mean stress and octahedral shearing stress are changed substantially from their initial states. Such changes take place around a borehole immediately following the drilling although they are short-lived. We developed a viscoelastic method of determining the in-situ stress field by relating the time-dependent behavior of the borehole with the tensor properties and stress field of the underground. In developing the viscoelastic relation, only isotropic and homogeneous

Jan 1, 1970

By E. D. Fields, R. W. Sayers, M. C. Tippett

The Duval Corp. porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an econornic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex Cu-Au-Ag ore is treated in a 4000-tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamoiphism and hydrothennal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes fitrther altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well-developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls. Recently, the Copper Canyon and Copper Basin properties of Duval Corp. have been added to the list of porphyry copper mines in Nevada, marking the first new copper open pit in this state in 15 years. The properties are situated in the Battle Mountain

Jan 1, 1970

By R. C. Ferguson, Harlowe Hardinge

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Oscar Johnson—In my opinion, the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. Comparing the entire groups of operators with those who have had the opportunity to make slow-speed mill studies, I think you will find the latter small in numbers. Most managers want the equipment worked to its maximum output. There are, however, some installations where plant and mill sizes are such that they can do the job with reduction of mill barrel speeds. The past and the present installations of the industry are laid out to get the most capacity for the least capital outlay. This is the case even with the plants of Chile Exploration, International Nickel, Morocco, and Anaconda, now under construction or being changed. The industry recognizes that most all equipment it buys today is good and can be depended upon for efficient performance. Under this scheme of things, I am doubtful that slow-speed ball mill operation will be generally applicable. With reference to the U. S. Bureau of Mines laboratory tests, I think table II could have been omitted. It is inconclusive as to maximum efficiency for the low-pulp level mill on hard ore. There should be no question about this point. However, data on mill speeds can be found to substantiate various theories as well as refute them. Gow, Guggenheim, Campbell and Coghill, in their paper on Ball Milling,' believe their 2 x 2 ft laboratory mill reflects results that can be expected from large mills. If so, then referring to their table 11, they state, "The conclusion to be drawn from this second series is that high speed, not exceeding 72 pct of the critical, favors capacity, as before, but that with proper conditions of operation high speeds may give as good efficiency values as low speeds. In this case the efficiency values are nearly constant. A horizontal curve would indicate that the amount of grinding was directly proportional to the power expended, and these tests suggest that such a coildition can be made to exist in commercial operations." Table II (From Paper by Gow et a1)2 Speed. Pot Critical 32 42 52 62 72 82 Capacity: Surface tons per hr (65- mesh) 266 42.1 54.4 65.9 74.3 74.1 Surface tons per hr (200- mesh) 56.1 87.4 112.7 137.1 154.2 153.0 Efficiency: Surface tons per net hp hr (65-mesh) 35.7 36.3 36.3 35.4 34.3 32.3 Surface tons per net hp hr (200-mesh) 75.3 75.3 75.1 73.7 71.0 66.0 Ore in mill, 1.b. 98 100 100 113 122 165 The field performance data, table 111, represents much effort in its collection and preparation. But, one must realize that there are many variables that effect the efficiency of grinding mill operation, and too much must not be assumed as to the effect of some specific change. Possibly with changes in mill speed, the results might be more consistent by also a change in ball rationing, type of ball, volume of ball charge,. p.ulp level and amount of pulp in the mill, pulp consisting, design of liner, circulating load, etc. Also, changes in ore character must be reckoned with when evaluating grinding performance. At present the Climax Molybdenum Corp. is running at much reduced capacity. Mr. James Duggan informs me that at mill speeds of 17 rpm, they save a $0.025 per ton on liners and $0.025 per ton in power, but, if the demand for molybdenum increased, he would go back to higher speed to obtain maximum tonnage, as the values from the increased tonnage would far more than offset the one half saving at the slower speed. The Jnspiration ran a six months' test between mills running 21 rpm and 23.5 rpm. The slower mills ground 10 pct less ore with a slight saving per ton, but when the reduced plant tonnage was checked back into the actual cost figures of concentration, the high-speed mills with their greater tonnage showed considerable advantage. To be convinced of possible practical results from the predictions in the conclusions, I think we would have to rely on the analysis of expert cost accountants to furnish the necessary proof figures. Hardinge and Ferguson are to be commended for the work in preparing this paper. I am convinced that our Massco engineers should go into higher speeds with our equipment. Harlowe Hardinge (authors' reply)—For one, I heartily agree with Mr. Johnson's opening statement that the effect of mill speeds on grinding costs must be studied along with capital investment and dollars gathered together as profits. It was on this basis and for this reason the paper was written. Mr. Johnson, on the other hand, takes the position that, on the whole, low speeds are not justified from the economic standpoint, basing his principal reason on the fact that lower mill speeds cut mill capacities and hence reduce the gross income from the product produced. There is no denying this point. It is almost axiomatic. It is for this very reason that the overall advantage of lower mill speeds has been discounted and even overlooked. It was for this reason mainly that the paper was written in the first place. It is one thing to plan an efficient operation at the outset, basing one's figures on the tonnage requirements at the time, and it is quite another to be confronted with the problem of increasing the output of an existing installation at a minimum of capital expenditure. Economic consideration of a new installation is greatly influenced by referring to an old one. Too often, the analyst assumes that if this practice is followed in the new installation, one would not go wrong. It is just here that he may be wrong. Past practice and low capital expenditure are all too frequently given priority over the engineer's analysis of operating costs. When we are able to start fresh, we should give proper weight to other economic factors which do not exist in an old installation. It is these economic factors that make it possible to spend at the outset just a little more money and get it back in a matter of months and effect big savings for years to come. F. C. Bond—This paper is of considerable importance in that it emphasizes a modern trend to operate ball mills at somewhat slower speeds than formerly. We have checked the data in the paper with that obtained

Jan 1, 1951

By R. G. Charles, E. A. Gulbransen, S. Barnartt

KINETICS of the reaction of zirconium with pure oxygen at elevated temperatures have been studied by several workers for periods of time up to 6 hr.1-1 In two cases,3-4 . the experimental values of oxygen uptake, w, as a function of time, t, were best fitted to the parabolic rate law w2 = kPt + constant. In others,3,4 the cubic rate law w3 = kot + constant, showed better agreement. The most recent data of Gulbransen and Andrew4 indicate that the choice between the parabolic and cubic laws for empirical representation of the data will often be arbitrary. This is particularly true if the first few minutes of the reaction with a clean zirconium surface is attributed to a different oxidation mechanism, for deviations from either rate law were found primarily during the initial period. Thus, the kinetics of this reaction have been too uncertain to permit safe extrapolation to oxidation periods of practical interest (many hundreds of hours). The data to be described are of interest, for they indicate that the cubic rate law applies over long oxidation times. The reaction of zirconium with oxygen at 1 atm pressure was followed at 350" and 450°C for 500 and 200 hr, respectively. Abraded test specimens of pure zirconium sheet' 3.0 X 2.0 X 0.012 cm in size were oxidized by the procedure previously described,3 which included periodic cooling to room temperature for weighing. The surfaces were polished to a 4/0 finish using polishing paper wet with kerosene, then wiped with petroleum ether and washed in redistilled acetone. Fig. 1 shows plots of log ? vs log t. Each curve represents the average of duplicate measurements, and deviations from the average were generally less than 3 pet. The cubic rate law (slope = 1/3) is closely followed. The rate constants, 5.2, x 10 -6 and 2.4, X 10- (mg cm-2)3 per hr at 350" and 450 oC, respectively, are plotted as log k, vs 1/T in Fig. 2, together with cubic constants calculated from the data of Gulbransen and Andrew4 for abraded specimens from the same lot of zirconium. Their data refer to runs of 6-hr duration at a pressure of 0.1 atm 0 and under conditions of uninterrupted heating. In spite of these differences, the latter data yield a straight line which appears to apply equally well to the new extended time data. The energy of activation for the oxidation process, calculated from the slope of this line, i.s 38 keal per mole. This may be compared with the value of 47 keal per mole found by Belle and Mallett3 at higher temperatures. It may be concluded tentatively that extrapolation of short-term oxidation data for zirconium to obtain the long-term behavior is best done through the cubic equation ?3 = kpt + constant. References ' E. A. Gulbransen and K. F. Andrew: AIME Trans., 1949, vol. 185, p. A.515; JouRNal OF Metals, August 1949. 'D.p. Cubicciotti Journal Amer Chemical August1949.Soc., 1950, Vol. 72, P. 3 V. Belle and M. W. Mallett: Joulnal Electro chemical Soc., 1954, ' E. A. Gulbransen 339.and K. F. Andrew: Oxidation of Zirconium Between 400" Gulbransenand 800'C.and AIME Trarzs.. 1957, vol. 209, p. 394; JOUR-Nal of Metals, April 1957. IS Barnartt, B G. Charles, and E. A. Gulbransen: Oxidation of 50 weight pet uranium-zirconium alloy, Journul Electrochemical SOC., 1957, vol. 104, p. 218.

Jan 1, 1959

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By R. L. Slobod, B. H. Caudle

In the past, the main emphasis in attacking the problem of the recovery of oil has been on the determination of fluid flow characteristics and residual oil saturation in the part of the reservoir which is contacted by a displacing phase. It is recognized that the determination of the fraction of the reservoir contacted in secondary recovery operations is also of great importance in predicting the ultimate recovery to be expected. A method is described in which radiographic techniques are used to determine these areal sweepout factors for any type of well spacing. Data showing the relationship of viscosity ratio and relative permeability to areal sweepout efficiency are presented for the five spot and the direct line drive well spacing patterns. Further applications of the method to studies of the displacement efficiency in the area contacted are mentioned. INTRODUCTION The problem of increasing oil recovery from typical reservoirs is generally attacked by trying to devise some means for reducing the residual oil in that part of the reservoir which is contacted. The fraction of the reservoir contacted in the displacement process. however, is also of major importance but has been given less consideration in the past. one reason for this neglect is the meager information available on the portion of the reservoir contacted and the magnitude of changes in this factor as operating conditions are varied. Until recently, the only means available for determining this quantity has involved the use of the electrolytic or poten-tiometric modelsl in which one is limited to working with a mobility ratio of unity. while means for calculating the volume of a reservoir contacted do exist. the calculations are very tedious for systems with mobility ratio different from unity. Recently several such determinations have been reported,213 and an experimental method involving a step-wise use of potentiometric models has been described.' A new method which has been developed for studying the areal distribution of phases in a porous medium is discussed below. This tool can be' used to determine the effect of operating variables such as viscosity, relative permeability, presence of gas, mobility ratio, rate and stratification on the fraction of the reservoir contacted by the displacing medium. This development based on the use of X-rays gives a pictorial representation of the location of the phases. Further, the amount of each phase at each point of interest can be determined quantitatively. X-RAY METHOD FOR AREAL STUDIES In this method the location of various phases distributed Over a test area are observed simultaneously by obtaining a photographic record of the transmission of X-rays through the test plate. This procedure is an adaptation of the radiographic techniques which have 10% been used in the medical and industrial fields. Just as the medical profession uses a chest plate to show spatial interrelationships, the location of an X-ray absorbing fluid and a nonabsorbing fluid in a porous medium can be determined by obtaining a photographic record of transmitted X-rays. Moreover, as changes occur in such a System, these changes can be observed by taking successive photographs. Previously, X-ray methods have been used in fluid flow studies to determine quantitatively the saturation at a given point in the system. The intensity of the transmitted X-rays was measured by an ionization chamber, so that a point by point survey of saturation could be made. In comparison with this earlier quantitative procedure, the photographic procedure which simultaneously observes the saturation at many

Jan 1, 1952

By Leonard R. Weisberg

HE procedure of directional freezing by the Bridgman technique1 is frequently used in crystal preparation. On those occasions where the crystal is regrown, it can be advantageous to Crop part of the ingot before regrowth to achieve purification. This note describes some simple, yet interesting, observations concerning the effects of cropping an ingot between successive freezes. First, it is not effective to Crop the front end of an ingot, whether or not the distribution coefficient, k , of the impurities is greater or less than unity. This can be shown as follows. The concentration C, of an impurity in a directionally frozen ingot of length d with a uniform cross section is given by where x is the distance along the ingot, and C0 is the initial concentration per unit length. It is assumed in deriving this equation that diffusion is negligible in the solid, is complete in the melt, and that k is constant. Consider that a section of the ingot Ad is removed from the front end. Then the average impurity concentration in the remaining (d- Ad) section of the ingot can be shown by integration to be given by When the ingot is remelted and refrozen, the new impurity distribution is given by where xl is the distance along the refrozen ingot. Substituting the value of c into Eq. [3], one finds This is identical to Eq. [11 when x = (x, Ad), which represents the original impurity distribution in the (d - Ad) section of the ingot after the first directional freeze. Therefore, the cropping and re-freezing accomplished nothing. This can also be seen physically by realizing that the average impurity content in the melt after the first Ad section is frozen, is identical to that after the resulting ingot has been cropped and remelted. Hence, it is assumed in the following sections that only the tail end of the ingot is cropped. However, it must be realized that for impurities with k greater than one, the pieces cropped from the tail end are purer, and are therefore saved. After cropping an amount Ad from the tail end of an ingot, the average impurity concentration of impurities in the remaining portion of the ingot is given by wheref= d/d. For the case of k < 1, the purification is defined as c,/c. It is obvious from Eq. [5] that the purification increases asf increases, but the increase in purification is not large. For example, iff is doubled from 0.1 to 0.2, the purification increases by only 10 pct for k = 0.5, by only 24 pct for k = 0.1, and by 32 pct for k =0.01. Much smaller values off than 0.1 are not desirable since insufficient purification is achieved. These figures indicate that much larger values off do not lead to substantial improvement, especially considering that much of the original ingot is lost. Therefore, it is generally useful to Crop about 1/10 of the ingot to achieve purification. As compared to doubling the value off, it is much more helpful to remelt, refreeze, and crop the ingot twice. Using Eq. [51 reiteratively, and assuming f= 0.1, it is found that the purification after this process is found to be increased over the purification after a single freeze and cropping by 33 pct for k= 0.5, 450 pct for k = 0.1, and 4100 pct for k = 0.01. This indicates that considerable purification can be obtained by this procedure. However, if purification is the main goal, one should resort to zone refining,3

Jan 1, 1962

By S. A. Spachner

An analysis of the powder patterns of the omega transition phase in three binary titanium alloys containing 8 pct Cr, 13 pet Mo, and 15 pet V, respectively, showed that all could be indexed on an orthorhombic unit cell. The unit-cell dimensions were all quite similar. There is evidence for the occurrence of more than one transition phase in Ti-Cr and Ti-V alloys. FOLLOWING the discovery of a new brittle phase in certain titanium-chromium alloys by Frost, Parris, Hirsch, Doig, and Schwartz,&apos; named ? by these investigators, much interest has developed concerning the identification of alloy systems in which this phase exists, kinetics of the transformation in such systems, and the crystal structure of the ? phases appearing. Omega has been found in alloys of titanium-manganese, titanium-molybdenum, titanium-iron,&apos; and titanium-vanadium.&apos; In the present work, a study was made of the powder patterns of the ? phase occurring in alloys of Ti-8Cr, Ti-13Mo and Ti-15V in an effort to obtain a basis of comparison for ? phases appearing in these different alloys. Comparison of Alloys for ?-Phases Two hundred mesh powders of Ti-8Cr, Ti-13Mo and Ti-15V were prepared. A portion of powder sufficient for three x-ray powder specimens was placed in a Vycor tube, evacuated to less than 0.1 µ pressure, filled with argon, and sealed. The tubes were then heated to 900°C, held at this temperature for 30 min, and water-quenched. Following this transformation to the ß phase, the specimens were quenched in lead or solder pots, held at the desired temperature for varying lengths of time and water-quenched. The heat-treatments used and the phases identified are listed in Table I. The intermediate water quench was used in lieu of direct downquenching from 900°C to the bath temperature desired to circumvent the possibility of transformation of the powder specimen from ß to (ß + a) while it was being moved from the homog-enization furnace to the lead bath. To check the possibility that upquenching to the bath temperature might bring into play a different mechanism than downquenching to this temperature, resistivity measurements were compared on Ti-8Cr rod specimens which were transformed isothermally at 400°C by downquenching from the solution-treatment temperature and those which were transformed at 400" C by upquenching ß specimens from room temperature. The results are shown in Fig. 1. No difference in transformation mechanism was noted. It soon became apparent that sufficiently detailed Debye-Scherrer photograms of the ? phase in the alloys which were to be used could not be obtained by the use of copper radiation. Although satisfactory photograms of ß and ß + a phases were obtained with this radiation, the ? phase appeared to exhibit mild fluorescence, making interplanar spacing computation virtually impossible. Molybdenum radiation appeared to offer promise in cutting down this fluorescent effect, the mass absorption of titanium for molybdenum radiation being 23.7 in contrast to 204 for copper radiation. The reduction in the accuracy in determining the location of the photo-gram lines caused by the shorter wave length of molybdenum characteristic radiation did not appear to be a significant factor. Utilizing a camera of 57.3 mm radius, best results were obtained for exposure times ranging between 30 and 40 hr. Tube potential

Jan 1, 1959

By V 7. 0 / 300 dpi

LAST fall, having a number of ore samples from mine-development work carried on in spite of the "Revolution," I was forced to do my own assaying again, after a lapse of many years. This gave me an opportunity to build a furnace for crucible assaying, using wood for fuel, along lines which had been developing in my mind since the time 20 years ago, when as general factotum at a little mining camp in western Chihuahua, Mexico, I had converted a crucible charcoal furnace into one using the reverberatory principle. Wood-burning furnaces have been described in technical literature, but I believe the present application will prove helpful to those of the profession who are working in out-of-the-way places. The furnace is shown in detail in Figs. 1, 2 and 3. Remembering the trouble caused by stoking my first charcoal furnace too heavily, I fired this one with but a few sticks of wood at a time. By this method I could run out a charge of 12 crucibles in 30 to 35 min., using 50 sticks of ordinary stove wood. Later I fill up the firebox, holding about 40 sticks, get everything ready, put the crucibles into the melting chamber and "fire up." Just as soon as the fire is well started the draft door is closed and the furnace allowed to heat up slowly for 5 min. Then the draft is opened (the door to the ash-pit) and the fire allowed to roar, which it does. In 20 min. from the time the fire is lighted the fire door is opened, the fire stirred along the grates, and 5 or 6 more sticks of wood thrown in. In 25 min. from the start, the draft is closed again, the cover of the melting chamber pushed back and the charges poured. The melts will be found to be perfect, and the crucibles to pour absolutely clean, if everything has gone right, as will usually be the case. A new charge may be put in, and fired with S to 10 sticks of wood at a tine, and be ready to pour within 20 min.; but it is just as well to leave the crucibles in the melting chamber a full 2.5 min. By using 10 sticks of wood to start the fire and adding 5 sticks as often as needed, which will be as soon as the last sticks fed in are in perfect combustion, the smelting can be completed in from 30 to 35 min., using from 35 to 40 sticks of wood. I consider this to be the best method of stoking.

Jan 10, 1914

By R. Schuhmann

PROBLEMS in expressing, interpreting, and using size-distribution data recur in many phases of mineral dressing; therefore it is desirable that size analyses be expressed in such a form, either numerically or graphically, that comparisons can be made readily. The size distribution of comminuted material is a result of a specific physical operation on the material and therefore should be governed by some definite physical principle, or cause-effect relation. Although this principle has not been discovered, it has been found that the size distribution of comminuted, homogeneous solids may be expressed by relatively simple mathematical equations. Two equations in particular, proposed by Gaudin1 and by Rosin and Rammler,2 respectively, have stood out, both having wide demonstrated ranges of application. The form and the method of application of the two appear almost irreconcilably different on the surface, but, as will be shown, they are asymptotic in the fine sizes when expressed in the same units. This paper gives the results of a further study of the Gaudin and Rosin-Rammler relations, made with the object of developing a form of size-distribution equation that will be more usable and more significant-particularly in comminution studies, both for interpreting the nature of size distribution and for evaluating surface. The work is summarized in the following: I. An equation relating cumulative per cent finer to particle size in the fine sizes is derived from Gaudin&apos;s original equation. That equation relates weight per cent retained on one size and through the next larger size in a geometric series of sizes to size (of the retaining screen, for example). 2. Comparisons with Gaudin&apos;s equation and with the Rosin-Rammler equation show that the cumulative equation applies to the fine sizes of all size distributions that fit either of these earlier relations, and, furthermore, has some advantages over each. 3. A simple graphical method of surface calculation based on the cumulative-equation plot is evolved and illustrated. 4. Additional confirmation of the cumulative equation was obtained in the more severe test of sizing down to the limit of a sedimentation balance a sample of jaw-crushed quartz. The equation was closely followed over a 20o-fold range in size, from approximately 0.4 mm. (35 mesh) down to 0.0023 mm. (2.3 microns), the lower limit of the size analysis made. There is no indication that the equation will not hold further to well below 2.3 microns. 5. Calculations of the surface produced in the jaw-crushing test mentioned above showed that at least 8o per cent of the total new surface was on particles finer than 35 mesh (about ½ 5 of the crusher setting). The minus 35-mesh portion was only

Jan 1, 1940