Search Documents

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington Counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin. The Ounulgee and Oconee Rivers drain the area. They and their main tributaries have flat, swampy flood plains covered with alluvium and for the most part thickly wooded. The divides between these streams are intricately dissected by the minor tributaries, which are spring-fed in steep-walled, cirquelike heads. Gullying and undercutting are active along the streams but are partly controlled by unusually dense vegetation. The mean altitude is about 350 ft above sea level and locally the relief ranges up to 200 ft. The area is near the inner margin of the Coastal Plain, and is underlain by Cretaceous and Tertiary formations. Its general location is shown in black in Fig 1. The division between the Coastal Plain and the Piedmont Plateau is actually a very sinuous line, the fall line, marking the extent to which erosion has stripped the Coastal Plain sediments from the southeastward- sloping surface of the crystalline rocks of the Piedmont.

Jan 1, 1952

By C. M. Heath, B. W. Gonser

Soft solders are used principally in the automotive, can-making, building construction and electrical industries, but their field of usefulness extends well beyond these principal users to a vast list of miscellaneous applications where metal joints are required. The most common soft solders and the only ones considered in this discussion are those composed of lead and tin, with or without various relatively small percentages of impurities or additions. A small amount of antimony is often purposely added. As an indication of the importance of these lead-tin solders, 8620 long tons of tin were consumed in 1934 in the United States for making new solder, and during most of 1935 from 900 to 1000 long tons often were used each month. In addition, many thousands of tons of secondary solder are recirculated annually. A great many factors influence the properties of joints made with soft solders. Fluxes and the fluxing procedure used to prepare the surfaces to be joined in order to give a true metal-to-metal contact are among the most important of these factors. The temperatures used, cleanliness of the work and general soldering technique have their effect, but when results are unsatisfactory they are usually attributed to the metallic solder itself and the raw materials from which it is made. Sometimes criticism of the solder is justified. The wrong composition may be chosen for a given job, impurities may be present that ruin certain desired qualities, or uniformity may be lacking. A solder may even be looked upon with suspicion because of its ancestry, regardless of its true composition and behavior. To clarify the effect of slight differences in composition as found in commercially refined solders, a comparison of properties of solders grouped according to their origin has been undertaken. This investigation seeks to give practical information on the properties of tin-lead solders produced from virgin metals, from commercially refined secondary solder, and from an electrolytically refined crude

Jan 1, 1936

By John B. Dilworth

In September, 1930, H. N. Eavenson, then Chairman of the Coal Division, appointed a Committee on Methods of valuing Coal Propelvties, with John B. Dilworth as chairman. The latter prepared a schedule' of features for consideration under the general headings of Undeveloped and Developed Coal Properties. These subjects were divided among the members of the committee and during the next year written discussions of his allotted subjects were received from each member. Mr. Grimes and Mr. Eavenson discussed the entire list,. These discussions were mimeographed and a set sent to each member before the meeting of the Institute in February, 1932. There was a general discussion at that meeting. At the meeting in February, 1934, Mr. Dilworth submitted a report12 which summarized the accumulated opinions and data and presented the conclusions of the committee as a whole on the subjects embraced in it's schedule. Members of the committee expressed the desire that some of the individual opinions be published for reference. Mr. R. Damon Hall's abstracts of these papers arc therefore presentrd herewith.3 Personnel of Committee John B. Dilworth (Chairman), Consulting Mining Engineer, Edward V. D'Invilliers Engineering Co., Philadelphia, Pa. Eli T. Conner, Consulting Mining Engineer, Seranton, Pa. W. G. Duncan, Jr., Superintendent, W. G. Duncan CoaI Co., Greenville, Ky. Howard N. EAveNson, Consulting Mining Engineer; Eavenson, Alford & Hicks. Pittshurgh, Pa. George Watkin Evans, Consulting Mining Engineer, Seattle, Wash. J. A. Garcia, Consulting And Constructing Engineer, Allen & Garcia Co., Chicatgo. III. John Alden Grimes, Valuation Engineer, Bureau of Internal Revenue, Washington, D. C. Otto Herres, Assistant Manager, United States Fue1 Co., Salt Lake City, Utah. J. R. Hicks, Consulting Mining Engineer, Eavensorl, Alford & Hicks, Pittsburgh, Pa. Robert D. Reeder, Mining Engineer, U. S. Bureau of Mines, Washington, D. C. Samuel, A. Taylor, Consulting Engineer, Pittsburgh, Pa. Bleeckee L.. WHeeler, Mining Engineer, Ford, Bacon & Davis, New York, N. Y.

Jan 1, 1934

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

By Alden Greninger

IN a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form { 133 } . In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form {110}, and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices are body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in mark-ing habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orienta-tion of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix.

Jan 1, 1938

A development which could prove significant was the announcement on September 18 by Lone Star Industries, Inc., Greenwich, Conn., that the Snyder process which utilizes shock phenomena to break down ore in seconds, is operational. J. R. Kringel, chairman and president of Lone Star, says this about the process: "This new approach to the comminution of ores not only provides better mineral liberation at lower capital and operating costs, but it also makes a significant contribution toward the more efficient utilization of the country's rapidly depleting mineral reserves." The Snyder process consists of loading the material into a chamber, introducing a compressible working fluid such as steam under 300-500 psi, or as low as 80 psi, and then opening a millisecond-action discharge valve, causing the material to become entrained in the expanding fluid. The mixed fluid moves through a duct toward a discharge zone at near-sonic velocity, and is subject to a variety of extreme shock phenomena which accomplish the desired size reduction and mineral liberation.

Jan 11, 1972

COMMITTEES. Iron and Steel. Albert Sauveur, Chairman. A. A. Stevenson, Vice-Chairman. Herbert M. Boylston, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. LOCAL COMMITTEES. Program Committee.-A. A. Stevenson, Chairman. Herbert A3. Boylston, J. E. Johnson, Jr., Henry D. Hibbard, E. Gybbon Spilsbury. Reception Committee.-J. R. Johnson, Jr., Chairman. Felix A. Vogel, William R. Walker. Dinner Committee.-E. Gybbon Spilsbury, Chairman. The opening session was held on Thursday morning, Oct. 16, 1913, at the Institute Headquarters in the Engineering Societies Building, 29 West 39th Street, New York, N. Y., and was called to order by President Rand, who addressed the meeting briefly before presenting Albert Sauveur, who responded to the President's address, and presided at the meeting. The following papers were then presented in oral abstract by their authors or authors' representatives: The Cleaning of Blast-Furnace Gas, by W. A. Forbes. Discussed by S. K. Varnes, H. N. Diehl, F. H. Wagner, Joseph Hartshorne, S. B. Marshall, J. W. Richards, J. E. Johnson, Jr., W. A. Forbes, and others.

Jan 12, 1913

Arthur H. Elliott, New York, N. Y.: We have all been very much interested in the results of Dr. Bone's work, which Mr. Ellis has presented to us this evening. The high temperatures attained by this method perhaps afford us an explanation of the temperatures reached in the puddling-furnace with its crude and almost primitive methods of burning fuel, by means of which we have, nevertheless, been able to melt iron in a comparatively short time, and keep it in a molten condition down to a high degree of purity. No doubt many of us have wondered, as I have done, how such a result could be obtained in such a way; and it occurs to me that, perhaps, Dr. Bone has supplied the explanation in disclosing the effect on combustion of burning gas and air after passing through, and in contact with, a porous refractory body. May not the fettling of the puddling-furnace have, in some degree, an effect upon the combustion like the influence of the porous diaphragm employed by Dr. Bone ?

Jan 1, 1913

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus 1/2 in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand.

Jan 9, 1950

Colorado School of Mines Scientific Society held its first meeting on Friday evening, Jan. 14.1916. H. C. Parmalee gave an interesting talk on the Loss of Cyanide by Hydrolysis. F. E. BRIBER, Secretary. The School of Mines Society of the University of Minnesota held a meeting on Thursday evening, Jan. 13, 1916, at which Fred A. Jordan gave a talk on Magnetic Concentration of Iron Ores. Mr. Jordan is at present testing the new magnetic concentrator designed at the. School of Mines Experiment Station. This apparatus, if successful, will open up an enormous tonnage of ore on the Cuyuna and Mesabi ranges. ADOLPH DOVRE, President. At the College of Mines, University of Washington, Seattle, 33 mining men, with experience varying from one to 25 years, have enrolled in the 19th Annual Three Months' Short Session. At the annual smoker tendered the Short Session miners by the student branch of the American Institute of Mining Engineers, Capt. R. H. Stretch of the Alaska Bureau, Seattle Chamber of Commerce, delivered an address on The Mineral Belts of Alaska.

Jan 3, 1916

Discussion of the paper of Leonard Waldo, presented at the New York meeting, February, 1911, and printed in Bulletin No. 76, April, 1913, pp. 555 to 559. HERBERT HAAS, San Francisco, Cal. (communication to the Secretary*):-Referring to Leonard Waldo's paper on Temperature Conversion Tables, I believe the following formulas can be easily remembered, and by reference to the thermomter scales of Fahrenheit (F.), Celsius (C.), and Réaumur (R.), their derivation and relation are at once understood n° F. = 4/9 (n°-32) R. = (n°-32) C. n° C.=(9/5 n° + 32) F. = 4/5 n° R. n° R.=(9/4 n° + 32) F. = 5/4 n° C. As the freezing point of water is at 32° F., corresponding to 0° C. and 0° R., 32 must be deducted from the Fahrenheit degrees when these are converted into C. or R. degrees. Likewise, to C. or R. degrees converted into F. degrees 32 must be added. The fractions 4/9 and 5/9 and their reciprocals are obtained thus:

Jan 5, 1913

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103c1 Engineers, killed in action near Fismes, Aug. 9, 1918. Bowles, Martin F., 2d Lieut., Co. B, 355th Infantry, killed in action, Sept. 3, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on Oct. 7, 1915. Dougall, Ralph,. 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on Oct. 12, 1917. Gordy, Sheppard B., died in service, Oct. 9, 1918. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service, Jan. 1, 1918.

Jan 1, 1919

As already announced in the notice of the 114th (New York) Meeting of the Institute, the ladies present met and organized the Women's Auxiliary of the Institute. All ladies of the families of members of the Institute-are eligible to this Auxiliary. The purpose and objects of the Auxiliary are well stated in the address of the President, Mrs. S. J. Jennings, in opening the organization meeting on the morning of Feb. 20, 1917. The address follows: "Ladies: Friends from far and near, on behalf of the Women's Entertainment Committee of the A. I. M. E., I extend to you a hearty welcome. "Most especially are we glad to see our friends from the Pacific Coast and the middle West, .whose royal hospitality to the members of the A. I. M. E. and their wives and daughters on their trips to California and to the Copper Country of the Southwest can never be forgotten. We are glad to be able in some small measure to return it.

Jan 4, 1917

By H. Hanemann

Discussion of the paper of H. HANEMANN and PAUL D. MERICA, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2371 to 2385. JOHN A. MATHEWS, Syracuse, N. Y.-I should like to ask the authors if there is any evidence of chemical change resulting information of, alpha iron from the gamma crystals found in nickel steel of high nickel content when stressed beyond the elastic limit, similar to the effect produced by drastic cooling. Would the stresses mentioned and the drastic cooling both result in an increase in magnetic induction? I would also like to ask the authors if they have made a test of the hardness. It would be very interesting to see whether the hardness decreased under the conditions of stress, as might be the case if alpha iron were produced. PAUL D. MERICA, Washington, D. C.-While it is impossible to state absolutely, it is my belief that the effect of deformation is approximately the same as, that of -drastic cooling, but we did not make a test, of the hardness.

Jan 5, 1916

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division Council J H Scaff (IMD) Chairman, Robert W Shearman, Secretary, J S Smart, (IMD), P T Stroup, (EMD), A W Schlechten, (EMD), J S Marsh, (ISD), A W Thornton, (ISD), M E Violin, (MED), D S Eppelsheimer, (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, J C Kinnear, Jr, T D Jones, Evan Just, John Marsh, M Tenenbaum Pacific Northwest Regional Conference A Y Bethune, General Chairman, Frank N Marr, Chairman, General Arrangements, R J Lapee, Chairman, C P Love, (EMD Program), W M Armstrong, Chairman, Physical Metallurgy Program, L W Heinzinger, Chairman (ISD Program), J P Spielman, Chairman, (MIED Program) New England Regional Conference K H Mairs, Chairman, W A Backofen, Vice-Chair¬man, Delmar E Trout, Secretary, G W Coleman, Treasurer, F H Wilson, Past Chairman, Members at Large Sidney Siegel, Boston, G F Donahue, Connecti¬cut Representatives from Connecticut Frank Chudy, J E Chafey Representa¬tives from Boston N L Reed, E Gordon

Jan 1, 1955

By William C. Peters

The pre-production interval, beginning with the recognition of an orebody's best potential and ending with significant production, contains time-dependent conditions well appreciated by miners but not always understood or appreciated by the landowners, investors, and legislators with whom a miner must deal. The expression persists, even outside of Western fiction, that someone has "found a mine." From a slightly more knowledgeable position, the question is asked "How long does it take to make a mine?" and an all-encompassing answer is expected. By scanning the discovery and development history of hundreds of mines and rejecting those which involve rehabilitation or expansion of older mines, some generalizations can be attempted. It should be kept in mind that while physical conditions involving the geology of the orebody and the geographic surroundings do not change markedly with time, technologic and economic conditions do change from year to year. The new methods, facilities, markets, land tenure, and politics form a pattern in which today's mines are made and which do sometimes modify the pre-production interval.

Jan 8, 1966

By Malcolm V. Lowry

At Balmat in northern New York State, the St. Joseph Lead Co.'s 2100-tpd zinc mining and milling operation is utilizing a unique thickener in conjunction with conventional crushing, grinding and flotation methods. From 1930 through 1962, zinc concentrates went directly from flotation to the filtering, drying and loading facilities, all of which had to operate 24 hr per day. Wide fluctuations in tonnage also had to be accommodated due to variations in the grade of ore. Many problems were thus encountered in filtering and drying, but the cost of installing a conventional, large diameter thickener could never be justified. In 1963, after thorough investigation, an unconventional thickener that is unusual in several respects was installed at Balmat. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes.

Jan 5, 1966

By Roger A. Harris

INTRODUCTION The Kidd Creek Mine produces a total of 3.6 million tons annually. Geologically the orebody is complex, containing rich values of zinc, copper, silver and lead which are mined and milled as two separate "ore types". Production is mainly from highly mechanized sub-level open stopes of approximately 300,000 tons each. The Mine Engineering Department has developed, and now operates, a computer system that is the subject of this report. It was created specifically to aid the daily work of the mining engineer and has features that are new and possibly unique in the industry. DESIGN OBJECTIVES In 1971 a task force, set up to investigate the subject of computer assistance to mine engineering, specified four design requirements which it felt a successful application had to satisfy. They were:- 1) The computer had to offer a TOTAL SYSTEM that was fully integrated into the routine mine engineering function. 2) The computer had to be directly usable by the current engineering staff, the majority of which had received no formal training in computing.

Jan 1, 1977

By N. C. Nissen, J. A. Thomas, A. Illis, K. N. Subramanian

Successful miniplant and laboratory testwork has indicated that high purity selenium can be produced from copper refinery slimes. The recovery technique fits into existing unit operations, and the selenium recovery in the new process was close to 99%. This recovery virtually eliminated any selenium being processed through the smelting stage. In addition, miniplant tests conducted at Inco Metals Co.'s J. Roy Gordon Research Laboratory in Mississauga, Ontario, have demonstrated the reliability of the process with respect to extractions, product quality, filtration characteristics, and effluent disposal. Inco's copper refinery at Copper Cliff, Ontario, produces about 500 t/d of copper with the anode slimes fall typically averaging 0.5% of the throughput. Investigations relating to the treatment of slimes within Inco's R&D have been conducted on several occasions since 1959, when the available alternatives such as acid or alkaline pressure leaching, aqueous or high temperature chlorination, roasting, smelting, etc., were considered. Interest in slimes processing was revived recently to meet increasingly stringent environmental standards and to replace equipment of a relatively old plant.

Jan 11, 1978

A visitor to the Republic of South Africa might profitably make his first sightseeing objective the Voortrekker's Monument at the administrative capital, Pretoria. Here he will find memorialized in sculptured stone the epic of the migrations of Dutch colonists from the Cape in search of new pastures and to escape British rule. He will see depicted the battles with the Bantus who were coming south also in search of habitable land, the peace treaties with great chiefs and the rise of Afrikaaner leaders. An American will be struck by similarities in events with his own history as well as in clothes and in type of covered wagons of the colonists. Before the latter half of the 19th century, little that transpired in South Africa was of any great international moment. The country had not attracted a great many settlers (about 15,000 Europeans in 1800 compared to about 2 million in the American colonies in 1776). Although some gold was being mined the majority of population was engaged in trade or subsistence farming.

Jan 12, 1962