Search Documents

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Robert W. Phelps

It is gratifying to observe the growing interest in the study of oil-well spacing. It should always be held in mind that the problem of optimum spacing is to obtain the maximum return of capital per acre drained. This naturally evolves.into a mathematical consideration. As mathematics is the basis of all science, an effort should be made to develop formulas which involve data obtainable in the early stages of development. The first information from a discovery well in a new field would be the character of the sand, rate of initial production of oil and gas, viscosity of the oil, rock pressure, etc. Later, from this well, if Herold's theories of hydraulic, volumetric and capillary controls are accepted, could he determined the ultimate production as without interference from drainage by subsequent well completions, and under which control the well is producing. If it should prove to be producing under capillary control, a rough estimate could be made of it's radius of drainage. With but one well, the radius of drainage, or the interference of drainage of individual wells by close spacing, would be estimated by comparison with similar conditions in other fields in which the development has progressed sufficiently to furnish the data. A second well that is spaced sufficiently close so that an interference can he observed after its ultimate production is estimated, will furnish data to develop a desirable spacing of wells which can be inaugurated for that area and which is capable of producing a uniform amount of oil under like conditions. In some fields this area will be extensive, in others each well location will require an individual study. In 1924, Cutlerl developed a scheme whereby he determined by tabulation a spacing of oil wells for the maximum return per acre. After a study of production in a number of fields, he developed the following as a tentative rule: "The ultimate production for wells of equal size in the same pool where there is interference (shown by a difference in the, production decline curves for different spacing) seems approximately to vary directly as the square roots of the areas drained by the wells. This rule may also he stated thus: The recovery from wells of equal size

Jan 1, 1929

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

By Howard C. Pyle, John E Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By John V. W. Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese, but taking into consideration the diminishing quality of iron ores and fuels as well as the increasing exaction of specifications for finished products, it may safely be assumed that, high-grade manganese ore will be more and more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits. Sources of Production Russia alone, of countries producing the major part of the world's stee1, has within its geographical boundaries sufficient manganese to supply its needs. The domestic production of England is inadequate and English requirements for high-grade manganese are supplied principally from India. France also draws largely upon India, as it depends upon foreign sources of supply except with respect to a small tonnage of silico-manga-nese and silico-spiegel produced in the Hautes-Pyrénées. Germany and the United States likewise depend upon foreign sources of high-grade ore, though each possesses comparatively large reserves of ferruginous manganese ore and manganiferous iron ore. At present the world demand for high-grade manganese ore is met with ease by the production of Russia, India, Gold Coast and Brazil.

Jan 1, 1927

By Howard C. Pyle, John E. Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By Howard Pyle

CORE analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.1 For convenience the subunit millidarcy, or one-thou-sandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil,4-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

By Henry Hibbard

AT THE beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as .it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By Henry D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

By C. H. Mathewson

Discussion of the paper of C. H. MATHEWSON and ARTHUR PHILLIPS, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 1 to 50. ZAY JEFFRIES, Cleveland, Ohio (communication to the Secretary*).¬The authors are to be congratulated for this interesting and valuable contribution. The paper as a whole shows very careful experimentation coupled with rare judgment in drawing conclusions. I have been working along similar lines for the last two years with other metals and alloys. In a short conversation with Dr. Mathewson about July 1, 1915, he mentioned the fact that different degrees of cold work greatly affect the temperature of recrystallization on annealing, Later I determined the recrystallization temperatures of iron, mild steel, and copper, with different degrees of cold work and found that the greater the degree of cold work, the lower the temperature of recrystallization on annealing. In the course of these experiments, I conceived practically the same ideas regarding the reasons for recrystallization as those advanced in the article under discussion. After a metal has been reduced by cold work to about one-fourth of its original area, the differences in orientation of different parts of a given grain can be seen plainly at a magnification of about 1,000 diameters. It is interesting to note that in Fig. A, Plate I, the lines of deformation are not parallel. For example,. in the large grain at the lower left corner of the micrograph, if the lines of deformation about 3g in. from the left edge are continued in a straight line, this line will intersect a straight line drawn as a continuation of the lines of deformation on the extreme right of the grain, at an angle of about 20°. Similarly, if the lines of deformation at the extremities of the large grain in the right central portion of the micrograph are extended, the lines intersect at an angle of about 35°. The individual lines of deformation are not straight. In some of these the parts of the broken lines intersect at angles as great as 15°.

Jan 5, 1916

By W. A. Tiller

SEVERAL authors1-6 have shown that, during solidification from the melt, the direction of formation of substructure boundaries depends upon the direction of heat flow and the rate of solidification of the metal. The most prominent of these observations was that a preferred orientation developed during the solidification of the columnar zone of an ingot which for face-centered-cubic metals was the <100> direction. Previous explanations1-&apos; given to account for this preferred orientation and the other boundary phenomena are all based on the premise that the phenomena are characteristics of the pure element. However, recent experiments by Rosenberg and Tiller7 have demonstrated that the preferred orientation in pure lead is the <111> orientation, and that the heretofore observed <100> orientation is due to the effect of solute on the mode of solidification of the metal. Teghtsoonian and Chalmers,4 studying striation boundaries in tin, and Chalmers and Rutter,5 studying corrugation boundaries in tin, showed that these substructure boundaries were aligned parallel to the axis of heat flow for slow rates of growth, and that the alignment varied from this direction as a function of the rate of growth. to approach the den-drite direction at high rates. Chalmers,6 studying the direction of formation of a grain boundary separating two crystals of different orientation, showed that at slow growth rates the boundary is parallel to the axis of heat flow, while at higher speeds it will deviate from this direction, sloping into the crystal whose dendrite orientation departs the most from the axis of heat flow. It is this phenomenon that allows certain crystallites in the chill zone region of an ingot to encroach on their neighbors and ultimately produce the preferred orientation of the columnar zone of the ingot. Since the previous explanations of this preferred orientation are unable to account for the recent observations,&apos; a new mechanism will be considered. This will lead to an explanation of the other substructure boundary phenomena as well. Investigations by Graf,8 Billig,9 Rsenberg,10 and others have demonstrated in a striking fashion that crystal growth takes place by the deposition of individual layers oriented along the close-packed planes of the material considered. This lamellar or

Jan 1, 1958

By H. D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe&apos;s great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. Rut discrepancies arise. Every maker and every User of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By R. J. Brison, R. D. MacDonald

This chapter is written primarily from the standpoint of development of flotation processes for treatment of specific ores. However, most of the principles and techniques discussed are equally applicable to other forms of applied flotation research such as improvement of procedures in existing plants and development of new reagents or methods without reference to specific ores. Because it is not possible to cover this subject in detail here, much of the material presented is in the form of a guide to the literature, with emphasis on readily available, English language publications. Details are included only if considered to be widely applicable or not readily accessible in the literature. Related subjects which are covered elsewhere in this volume, such as flowsheet design and statistical techniques, are not emphasized in this chapter. The material presented is intended primarily for those familiar with the theory and practice of flotation, but with limited experience in applied flotation research. It may be of value to the experienced investigator as well, by calling to his attention some useful viewpoints or techniques that he may have overlooked. It has often been said that flotation is more of an art than a science. In- deed much of the knowledge of flotation behavior is empirical. However, the unsystematic, artisan approach to flotation problems results only in an ac- cumulation of unrelated data. Like any other physical or chemical process, flotation is amenable to investigation by systematic experimental methods. The experiments should be based, as far as possible, on an understanding of the natural laws that govern the process and on good experimental procedures. SAMPLING OF A DEPOSIT In working out a flotation process for a mineral deposit, no step is more important than that of obtaining a suitable sample or samples. Experimental procedures cannot compensate for the lack of a representative sample. Methods of sampling a deposit have been published elsewhere,l-4 but a few points are of special importance from the standpoint of flotation. First, the sample should be representative of the deposit, not only in respect to chemical composition, but also in respect to mineralogical composition and degree of dissemination of the valuable minerals. To help ensure

Jan 1, 1962

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

HARD as it is at any time to provide more than three million tons of coal each year for power plants, the task really gets rugged in the wintertime when the fuel freezes solid in the cars. At the Marysville plant of the Detroit Edison Co. the problem of unloading cars of frozen coal was severe because there was an unloader over only one of the two tracks in the coal unloading house. Moving downward by their own weight, with no driving force to aid them, the spuds of this old unloader were unable to break through the crust on a frozen coal car. 20,000 Lb Force To meet this problem, a new mechanical car unloader was installed over No. 2 track and placed in service in December 1947. It is a Kenney type unloader built by Heyl & Patterson, Inc. of Pittsburgh, Pa., a modification of equipment originally designed to unload iron ore cars. The major advantage of this unloader is the force with which it can drive the sharp spade on the end of its ram down through the pockets of a frozen coal car. The unloader consists of the following major units: 1. A traveling bridge structure. 2. A traveling trolley. 3. A retractable and oscillating ram. 4. The operators cab and controls. The bridge is provided with safety hooks to prevent its being lifted from the rails by the upwards push of the ram. The bridge will travel 190 fpm and has sufficient traction on its four wheels to move three loaded 70 ton cars. The trolley runs on tracks supported by the bridge girders and also has upper tracks to control the push from the ram. Two of the single-flange trolley wheels are driven by a one and a quarter hp dc motors equipped with magnetic brakes. The ram is raised and lowered by a 20 hp dc motor equipped with a magnetic brake. A full stroke of a little over 14 ft is given the ram through its rack and pinion drive and the spade can be pushed down into a loaded car with a force of about 20,000 lb. A 15 hp dc motor with a magnetic brake is applied to this drive and is able to swing the ram 45º either side of the vertical. The usual procedure in emptying a coal car is first to drive the sharp spade down through the coal until the pocket is opened and the coal starts to run out the hopper. When all the hoppers are open, the sweeping action of the ram and spade is used to move the remainder of the coal in the car over to the open hoppers. The travel of the trolley permits cleaning the sides of a coal car with the edges of the spade, using the sweeping motion of the ram. It is still necessary to clean out the corners of the car by hand. Final Clean-Out This unloader was a new development and there were improvements to be made before it was completely satisfactory, such as reduction in speed and conversion to ac drive motors. However, it helped at Marysville and unloaded many frozen cars that would have taken a lot of heating to thaw out enough for the old unloader to handle. The mechanical coal unloader described above was a considerable improvement but still left a job to be done by hand-the final cleaning out of the coal cars. The ram had the ability to open a hole through the hopper cars, but did not meet required unloading speed. To eliminate hand cleaning a car shakeout, manufactured by Hewitt Robins, Inc. was added to the installation. This equipment is used to clean the coal car out after the unloader has provided an

Jan 1, 1952

By L. A. Wood, A. G. Winslow

Subsidence has occurred in several areas of the upper Gulf Coast region of Texas, although in most cases this is not evident without precise instrumental leveling. As referred to in this report, the region comprises about 7200 sq miles of the Gulf Coastal Plain and includes all or parts of the following counties: Harris, Fort Bend, Waller, Brazoria, Galveston, Liberty, Chambers, Orange, and Jefferson (Fig. 1). Topographic relief is low, ranging from sea level at the Gulf of Mexico to 300 ft or more in northwestern Harris County. In this upper Gulf Coast region, which embraces the most heavily populated and industrialized parts of Texas, industrial and municipal water supply is obtained chiefly from wells. Largest center of ground-water withdrawal is the Houston-Baytown area, where about 200 million gallons per day was pumped in 1956 for municipal and industrial use. Other large centers of ground-water withdrawal include the Alta Loma sector and the heavily industrialized Texas City area in Galveston County, where about 23 mgd was pumped in 1956. In the Freeport area in Brazoria County about 6 mgd was pumped in 1956 for city and industrial supply. In addition to withdrawals in metropolitan districts, great quantities of ground water are supplied by irrigation wells to thousands of acres of rice. These wells are widely dispersed over many miles, principally in Harris, Waller, Fort Bend, Brazoria, and Liberty counties, and effects of pumping are not so readily noticed as in the industrial and metropolitan sectors. Subsidence: Starting with the 1905-1906 line from Smithville, Tex., to Galveston, the U. S. Coast and Geodetic Survey has extended a network of first and second-order level lines throughout the upper Gulf Coast region. In 1918, when a line was run from Sinton, Tex., to New Orleans, La., a tie was made to the 1905 leveling at Houston. In 1932-1933 a line was run from Palestine, Tex., to Houston, and a good deal of leveling was carried out in the vicinity of Houston. At this time the entire network was adjusted to the Sea Level Datum of 1929. In 1935-1936 and 1942-1943 several new lines were run and considerable releveling was performed. Supplementary adjustments were made after both the 1936 and 1943 levelings in order to reduce the elevations to the Sea Level Datum of 1929. These adjustments probably masked some of the subsidence that had occurred up to that time, although a certain amount of subsidence was noticed in the 1943 leveling. When several lines in the vicinity of Houston and Galveston were releveled in 1951, the regional nature of the subsidence became apparent.&apos; Direct comparison with the 1943 leveling was possible because the datum was not changed. Comparisons with prior leveling were unreliable because of differences in the early and subsequent datums. In 1953-1954 many lines in the region were re-leveled and in 1957 the entire network, including the elevations previously determined, was readjusted to determine the changes in elevations as indicated by various levelings between 1905 and 1953-1954. In this instance the adjusted elevations were held fixed near the boundaries of the region where the bench marks seem to have remained stable. The only sea-level connection held fixed was the connection of the 1905 leveling to the 1903-1906 tidal series at Galveston. Almost the entire region has been at least slightly affected by the subsidence, some areas to a great extent. The profiles of subsidence (Fig. 2) and the map showing the contours (Fig. 3) illustrate both regional and local changes. A large area of subsidence is centered in the Houston-Baytown district, where the maximum recorded is about 2.7 ft between 1905 and 1954. This probably falls short of the actual maximum, since land surface subsided as much as 2.5 ft in the industrial section alone between 1943 and 1954. Sub-

Jan 1, 1960

By M. R. Geer, H. F. Yancey

THE performance of coal-washing equipment, that is, the effectiveness with which coal and impurity are separated, is a subject of undisputed interest to all concerned with the preparation of coal. Through the years much has been written in both American and European literature on the performance of coal-washing equipment and its interpretation, but until recently no effort has been made to consolidate this wealth of information into a single, comprehensive treatment of the subject. A splendid effort in this direction was made at the First International Conference on Coal Preparation held in Paris in June 1950 in which representatives from virtually every coal-producing country participated. Although the scope of the conference covered the entire field of coal preparation, many of the sixty-odd papers and a great deal of the discussion dealt with the subject of evaluating washery performance. Prominence was given this subject by the Centre d&apos;Etudes et Re-cherches, des Charbonnages de France, which sponsored the conference. This research organization, generally referred to as Cerchar, was formed in 1948 following the nationalization of the French coal industry. Since that date it has conducted an intensive study of coal preparation. Perhaps because of a fresh viewpoint, Cerchar realized immediately that complete information on the performance of French washeries and a thorough understanding of the mechanism of gravity separation were the fundamental prerequisites in a program to improve preparation practice. For this reason Cerchar concentrated on obtaining performance data and on a comprehensive study of methods of evaluating such information. Some idea of the magnitude of this work will be appreciated from the fact that 175 performance tests were made in 44 plants. The work performed by Cerchar emphasized a condition that is recognized by many of those concerned with coal preparation, namely that the lack of uniformity in presenting data on washery performance, the diversity of methods used in evaluating such information, and the frequent confusion of the terms related to performance have been prime factors militating against the progress from art to science. Thus, Cerchar feels that standardization of the methods employed for evaluating washery performance, not only in France but in the entire world, is essential to progress, and the prime objective of the Paris conference was to seek international standardization of the evaluation methods advocated by Cerchar. At the conclusion of the conference the question of standardization was referred to the International Standards Organization. A careful study of the dozen papers on the subject of evaluating washery performance presented at the conference reveals that none of the methods is new; most of them date back over a decade. Nevertheless, the intensive scrutiny of these methods brought about by the conference unquestionably has resulted in a valuable exchange of ideas and a clarification of thought that could scarcely be achieved in any other way. The object of the present report is to make available to the American coal industry the ideas developed at the conference which seem most important from an American viewpoint and to provide a critical analysis of some of the evaluation methods advocated by Cerchar. The various methods of evaluating washery performance are illustrated partly with data that have been published in American literature, and some new data have been obtained as the result of experimental work undertaken since the conference to provide information on certain controversial points. An English translation of the proceedings of the conference, including the discussion as well as the papers, will be available,&apos; and previous to the conference Coal Age2 published a very brief description of some of the principal evaluation methods used by Cerchar. Americans will appreciate as well as do the French the desirability of standardizing both the termi-

Jan 1, 1952