Search Documents

By Leo J. Vogel, E. D. Hummer

INTRODUCTION by E. D. HUMMER An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contributes to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and operating costs of the plant, but greatly affects the design of the refuse disposal system. The design of a mine and plant should include the location and the estimated capacity of the disposal areas for the life of the property or plant. Complete evaluation of the disposal system and an estimate of its annual cost of operation over the life of the property or plant should be incorporated in the plant and mine evaluation. Plant design should be as simple as possible, consistent with the efficient production of clean coal. Material transfer points, crushing, screening and pumping operations should be kept to a minimum to reduce degradation and the subsequent increased difficulty and cost of refuse removal. The maintenance of good process control by operating management will result in a minimum of misplaced material in both refuse and clean coal. Reduction of misplaced float material in the plant refuse is an important factor in preventing combustion in the refuse storage pile. THE REFUSE DISPOSAL AREA Combustion in refuse piles occurs when air enters the pile in sufficient quantity to support oxidation. At certain rates of air in-filtration, the heat produced by the oxidation process is not dissipated and temperature rises.

Jan 1, 1968

By Ralph H. Sweetser

Carbon in pig iron is not only essential but, ordinarily, it is the most abundant metalloid present; iron without carbon could not be pig iron. Carbon in pig iron has been accepted, but seldom specified. How it gets into the pig iron as it is being smelted in the blast furnace, and why just about so much of it enters into the pig iron in certain blast furnaces, and more of it,; or less of it, enters the pig iron in other blast furnaces, or in the same blast furnace under varying conditions, are problems that have not yet been satisfactorily solved. During my own practical blast-furnace experience, I collected analyses of pig iron, including the graphitic and combined carbon, and recorded them in reference to the percentage of silicon present, having in mind the generally accepted explanation that "silicon drove out the carbon." To this actual experience, I have added some analyses given to me by J. B. Rogers, who was superintendent of the blast furnaces of the Ashland Iron & Mining Co., Ashland, Ky., and was making "silvery iron" at the time. These analyses are shown in Table 1. The analyses do not tell the whole story, but they show that with Pocahontas beehive coke, the total carbon was generally high. The data relating to the composition of the slag are lacking but my own customary practice was to have a rather basic slag. During my experience in making pig iron for the Bessemer and open-hearth departments, there were times when the steel men would complain about some mysterious quality in the pig iron that caused bad steel, in spite of the fact that the percentages of silicon, sulfur, phosphorus and manganese were within the specifications. Many reasons were advanced for this undetermined "poison" in the pig iron, but the favorite one offered by the steel men was that the blast-furnace man had "oxidized" the pig iron at the tuyeres in his eagerness to get big production and low cost. To these complaints of the users of steel-making pig irons were added those of the gray iron-foundry men and the malleable iron men. These groups are unaninlous in their conclusions that the trouble lies with the blast-furnace men; but there is not yet any harmonious conclusion as to the exact cause and remedy.

Jan 1, 1927

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By Stephen Royce

[Stephen Royce.. I .......................... E. S. Moore.. 9 .......................... E. L. Bruce.. 10 ......................... J. E. Hawley.. 11 ........................ L. M. Scofield.. I 2] STEPHEN ROYCE, * Crystal Falls, Mich.Having examined and reported upon the Steep Rock Lake property and vicinity on several occasions for clients, and having kept in touch with the operation from 1938 on, the writer offers the following discussion of the valuable paper by Messrs. Roberts and Bartley, which was so kindly prepared in response to the writer's earnest request, made as a member of the Committee on Mining Geology. ORIGIN OF THE ORES The writer wishes to express complete agreement with the authors that the origin of these deposits was replacement action by hot ascending sulphide solutions of igneous origin, gaining access via the limestone and dolomite breccia channels, and acting mainly to replace the dolomite and limestone breccia with hematite and hydrated hematite. Some replacement in adjoining greenstones and tuffs by the same solutions may also have taken place, but the latter occurrences may represent replaced iron formations originally bedded in with the volcanics. Iron formation in the same relationship to volcanics is extensively developed on the western Menominee Range of Michigan, in the Middle Huronian belts; also appears in similar relations on the Vermilion Range; and is abundantly exposed in the same stratigraphic position no farther away than the southeast arm of Steep Rock Lake itself. Furthermore, the writer's classification of drill cores, made June 11, 1938, on the prop¬erty, contains the following, for hole 8, in the original strike of the A ore body: "332-342 ore; 342-350 much-leached sugary chert with thin ferruginous slate bands." This is a typical iron formation. The ore in this first group of holes (Numbers 6 to 13, incl.) is described in the writer's 1938 notes as follows: "The ore is hard, massive hematite with some limonite, and shot through with many small vugs." The breccia forms in the float ore and in the drill samples were also noted. As a field classification this does not check badly with Professor Schwartz's microscopic work. Notes supplied by Mr. Neeland, then geologist at the exploration, show: "Hole 23 has some iron formation, not logged yet." It appears therefore that there is some iron formation at the exploration, much iron formation in similar stratigraphic position in the vicinity, and iron formation similarly located as to volcanics on the Vermilion and western Menominee Ranges. Certain of the holes, notably Holes 25 and 27, showed some specular hematites resembling those known to be formed from cherty iron formation elsewhere. Hence the writer concludes that at least a small part of the Steep Rock ores results from replacement of iron formation. By far the greater part of it is, as the authors say, clearly a replaced limestone and dolomite breccia, with the breccia outlines still preserved in much of the ore, and all of the replacement is by hot ascending waters. The authors' citation of the neighboring Atikokan pyrite, pyrrhotite and magnetite

Jan 1, 1943

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By Robin O. Williams

The textures which are produced by simple shear in poly crystalline samples of copper, brass, aluminum, iron, and zirconium have been determined. For the fcc materials, there are two major textures, both of which are oriented for slip on the usual slip systems. It is shown that each grain will, in general, give rise to both orientations through the production of deformation bands. This is considered a clear demonstration that such bands aye produced by the heterogeneous deformation which takes place instead of the five-slip-system model considered by Taylor. The results on iron and zirconium are more limited but would appear to exhibit certain additional complexities. It is suspected, however, that the general consideration of deformation bands may apply here also. One finds some correlation between the textures produced by this single shear and the conventional textures although it would appear- that additional data and analysis are requived to produce a strong correlation. It is somewhat remarkable that of all the texture investigations only a very few have been concerned with the action of simple shear on polycrystalline aggregates. Of these limited investigations, all used torsional strains and only in Backofen's' and Backofen and Hundy's "ork was sampling carried out so as to derive a texture in terms of the shear direction. Some rather remarkable conclusions re- sulted from Backofens'1,2work: 1) the rate of texture formation in copper is high, being almost complete at a shear strain of unity; 2) the texture does not change if the sample is sheared back, although the surface grains return to their original shape; and 3) the texture is complex in that it has four components, three of which have [110] as a shear direction. These conclusions were based on both qualitative and quantitative data. Shear deformation is intermediate in complexity between simple shear of single crystals and the usual deformation of polycrystals; hence, one might expect to learn considerable from the extension of this work. CONVENTION Deformation in simple shear has the lowest possible symmetr3, less than the other simple modes of deformation (rolling, drawing, and compression); hence, one cannot necessarily expect the textures to have the same degree of symmetry. The geometry of the process is represented by Fig. 1 along with its sltereographic projection. One has the shear plane, the shear direction, the mirror plane normal to the shear plane and containing the shear direction, and a neutral plane normal to both the shear plane and mirror plane. These planes divide the projection into four quadrants. These quadrants are not, however, identical, since all directions within the upper left and lower right are being shortened by the shear process, and the other directions are being lengthened. The first kind are called compression quadrants and the direction of greatest contraction rate, at 45 deg, is labeled with a minus sign; the corresponding direction of greatest extension rate

Jan 1, 1962

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures'-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.' The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant' determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle' and ~ayward.' According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By W. H. Bassett, J. C. Bradley

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (I) Depth of deoxidation of copper heated in reducing gas is grealer the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this diflerence in depth of deoxidation is thai, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much more rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900" C.; that is, deoxidaion is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide presenx in the copper. In 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By E. Gregory, A. Coucoulas

Carbm dioxide, which exists metastably as a constantly subliming molecular solid in a normal room-temperature environment, has been shown to exhibit many microstructural features which are similar to those observed in metals and ceramics at temperatures approaching their melting points. An examinution has been made of some of the factors affecting a brittleness condition known as "smzdiness" which occurs in solid carbon dioxide. It has been shown to be highly dependent on manufacturing and storage conditions and is thought to be a marked intergranu-lay brittleness which results from a combination of excessive grain growth and a concentration of gas-filled pores at the grain boundaries. In the course of an investigation carried out to explain certain physical and mechanical properties of solid carbon dioxide, observations were made of the microstructure and fragmentation of samples after fabrication and storage under varying conditions. Many similarities between the structures of solid carbon dioxide observed under ambient conditions and those existing in metal and ceramic systems at temperatures approaching their melting points have been observed. There are, however, important differences between solid carbon dioxide and the common metallic and ionic solids which result primarily from the differences in the nature of the bonding forces. Despite these differences, the relative ease with which certain microscopic observations can be carried out, may make solid carbon dioxide a useful material model for the physical metallurgist and the ceramist. It could also prove a valuable material for educational purposes where it is required to illustrate grain phenomena which normally can only be seen with the aid of a high-temperature microscope, and after prolonged chemical or thermal etching.

Jan 1, 1963

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By Irwin Roman

IT has been known for many years that when a wire is moved in a magnetic field, an electromotive force is developed which is proportional to the rate at which the wire is moved in a direction perpendicular to the magnetic intensity and to the magnetic intensity itself. If the ends of the wire are connected to a current indicator, the current behaves exactly as though the source of electromotive force were a galvanic cell. If a wire is wound circularly and rotated uniformly around a diameter not parallel to the intensity, the current flowing through the wire will be alternating of sinusoidal shape. If, instead of a single loop, there are several turns wound in a short helix, the electromotive force developed will be approximately proportional to the number of turns, the area of the helix and to the speed of rotation. The maxi-mum electromotive force will be devel-oped when the axis of rotation is perpen- dicular to the field; if this is not so, only the component of the intensity that is perpendicular to the axis of rotation is effective. This is the principle of the usual earth inductor. With a few turns of wire and comparatively slow rotation, FIG. 1.-MAGNETIC GRADIOMETER. it is possible to produce a considerable deflection of a galvanometer. If two similar coils are rotated together at two different points for which the magnetic field intensities perpendicular to the axes of rotation are different, the electromotive forces developed will each depend on its corresponding intensity and be a measure of that intensity. If the inten-sities are sufficiently different so that the electromotive forces may be compared, the two intensities may be compared. This is the principle

Jan 1, 1934

By J. C. Prof. Smock

(Read at the Philadelphia Meeting, February, 1878.) THE fire-clays of New Jersey belong in two geological ages, the cretaceous and quaternary, or post-tertiary. Three very small deposits of plastic clays have been discovered within the limits of the Archoean rocks. These are not refractory and of little importance, excepting in a geological consideration. They have resulted from a decomposition of the feldspars of the rock in situ, and they have been classified as inferior kaolins.

Jan 1, 1878

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By G. F. Loughlin

MORE than 20 years have passed since the publication of Lindgren and Ransome's report on the Cripple Creek District,1 which was made when the district was much more active and prosperous than in recent years. They concluded that the output of the district, which had reached its maximum of about $18,200,000 in 1900, would gradually decline, and their conclusion has been confirmed by records of subsequent production. Between 1905 and 1915 annual declines were partly compensated by encouraging increases, especially in 1908, 1914, and 1915; but a rapid continuous decline followed, due largely to the war and its after effects, until in 1922 the value of output was only slightly more than $4,000,000. It rose to nearly $5,000,000 in 1924, but declined again in 1925 and in 1926, when it was about $4,400,000, and represented ores mainly from deep levels in the Cresson and Portland mines. The profitable operations of these two mines were the principal factors leading to a study of ore at deep levels in the district by the U. S. Geological Survey in coopera-tion with the Colorado Metal Mining Fund. The principal reasons for Lindgren and Ransome's conclusion were three: (1) the greater cost and difficulty of deep exploration; (2) the decrease in the number of veins with increasing depth, and (3) the probability that the telluride ore, believed to have formed at comparatively low temperature, would not persist indefinitely -in depth. Operations since they made these statements have verified the first two, but call for some modification of the third. Rich telluride, ore is being mined at a profit in the Portland mine 3000 ft. below the present surface, or 5000 ft. below the original surface of the Cripple Creek volcano, as interpreted by Lindgren and Ransome. The question arises, therefore, as to the number and extent of such deep deposits, and the answer, so far as it can now be given, must be based mainly on structural data, supplemented by data on the processes of ore deposition. Presentation of these data based on a study of deep mines in the southeast quarter of the district, the only

Jan 1, 1927

By Archer Wheeler

THE copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minere du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1932

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux' reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann' and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By John H. Puffer, Andreas H. Vassiliou

The Bemco mine area is within the Precambrian igneous and metamorphic rock terrain of the New Jersey Highlands province. Rocks In the area include a pyroxene granite, a hornblende granite, a quartz-oligoclase gneiss and a pegmatite and its host rock, a lens of amphibolite which becomes a sulfide-rich pyroxenite near the ore zone. The ore-bearing zone occurs along the hanging wall and foot-wall contact of the pegmatite which was emplaced discordantly into the amphibolite-pyroxenite.

Jan 1, 1985

President MRS THORNS E LLOYD 14 Green Hill Road Morristown, N J First Vice-President MRS A B PARSONS 52 Edgewood Road Scarsdale, N Y Second Vice-President MRS H A PROSSER 1001 Park Avenue New York, N Y Third Vice-President MRS HARRY J WOLF 3 Glenwood Avenue Littleneck, N Y Fourth Vice-President MRS MARK LAWRENCE REQUA 140 North Plymouth Blvd Los Angeles, Calif Fifth Vice-President MRS NEWELL G ALFORD 314 South Homewood Avenue Pittsburgh, Pa

Jan 1, 1952