Search Documents

By Igor Martins dos Santos

O nitrogênio waste, que é chamado assim por ser mais impuro, devido à existência de uma porcentagem aproximada de 2% mais de oxigênio no mesmo, utilizado exclusivamente no processo de “Slag Splash” na Aciaria, possui um contrato fechado de volume para fornecimento (7.000 Nm³/h, à pressão de 30 bar), o qual estava sendo utilizada aproximadamente a metade do mesmo (3.500 Nm³/h). Como no processo produtivo da CSA, é utilizado o nitrogênio de baixa pressão (16 bar) em grande quantidade (21.600 Nm³/h, sendo aproximadamente 5.600 Nm³/h acima do contrato de fornecimento), foi feito um projeto para interligar as duas linhas de nitrogênio através de aproximadamente 420 metros de tubulação, com sistema de controle integrado e analisador de oxigênio para garantir a concentração mínima de 1% de oxigênio no Nitrogênio de baixa pressão, devido à necessidade de algumas áreas. Nos primeiros seis meses após implantação, foi contabilizado uma economia de aproximadamente R$4.0 milhões (aproximadamente 3.100 Nm³/h de consumo).

Oct 30, 2017

By Juvenil Nunes Oliveira Júnior

O tubo de papelão é um material bastante versátil e pode ser utilizado de diversas maneiras, possibilitando sistemas construtivos variados que, muitas vezes, geram obras arquitetônicas arrojadas [1]. Um abrigo emergencial deve possuir as seguintes características: rápido fornecimento, baixo custo, flexibilidade de adaptação ao terreno, fácil montagem/desmontagem que permita a participação do utilizador do abrigo. Outro ponto é possuir princípios sustentáveis e funcionais, aliando eficiência e diretrizes lógicas para o design do produto. Este trabalho tem como objetivo a caracterização mecânica de tubetes de papelão para a utilização em abrigos emergenciais.

Aug 16, 2017

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Gabriel Burlandy Mota de Melo

Nanopartículas de ferrita de manganês (MnFe2O4) foram dispersas em parafina e as propriedades físicas do compósito resultante foram investigadas por ressonância ferromagnética (RFM). Os resultados mostraram que a dispersão em quantidades moderadas de parafina aumenta significativamente a anisotropia magnética das nanopartículas de ferrita, um resultado que pode ser de interesse para aplicações práticas do compósito.

Oct 30, 2017

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Rafael Lioji Kogake

O Alto Forno n° 2 é responsável por cerca de 40% da produção de gusa na CSN. Uma das principais utilidades responsável pela transformação do minério de ferro em gusa é o ar soprado que é fornecido por dois turbo sopradores da Central Termoelétrica n°2. Para que ocorra o processo de transformação do minério é necessário que o ar soprado seja aquecido. Isto é feito através dos regeneradores, os quais aquecem o ar para cerca de 1.300°C. Como cada regenerador tem um tempo de campanha, é necessário fazer a troca do mesmo a cada 1 hora. Nesse momento de mudança de regenerador, uma parte do ar soprado é desviado para o regenerador que está entrando em operação e ainda está vazio. Com isso, há uma perda pontual de produção indesejada, além de causar instabilidade no processo. A solução encontrada para reduzir este problema foi aumentar a vazão de sopro durante o período de troca de regeneradores, garantindo assim uma maior produção e melhor estabilidade do Alto Forno 2. Este trabalho apresenta o estudo do problema em questão, a metodologia utilizada para a sua implementação e os resultados alcançados.

Jul 31, 2018

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By André Alexandrino Lotto

A demanda global por energia renovável vem aumentando ao longo dos últimos anos. A energia solar é uma energia limpa e abundante, mas seu uso ainda é limitado por causa dos preços altos e baixa eficiência das células fotovoltaicas. O silício bruto, também chamado de silício de grau metalúrgico, tem sido alvo de muitos estudos visando sua purificação a um nível suficiente para aplicações de energia solar por processos mais baratos do que o processo convencional, chamado Processo Siemens. Neste trabalho, 3 kg de silício de grau metalúrgico foram fundidos por plasma térmico numa atmosfera de vapor de água, hidrogênio e argônio. O teor de boro foi reduzido de 10 ppm para 0,09 ppm em 18.000s (5 horas), mostrando que o processo poderia ser uma alternativa viável ao processo tradicional por via química

Aug 8, 2018

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By Leslie Perterson

O trabalho teve o objetivo de analisar a atual condição de descarepação da empresa X e fornecer a melhoria no processo por meio da substituição dos chuveiros, troca dos bicos de descarepação e até mesmo a combinação desses dois fatores. Para isso, foram avaliadas a velocidade do escoamento interno dos chuveiros, a turbulência gerada e eficiência dos atuais bicos instalados por meio de análise CFD (Computational Fluid Dynamics). Em posse desses dados, foi possível sugerir a configuração ideal dos chuveiros no que diz respeito ao diâmetro da tubulação, espaçamento de bicos e o bico de descarepação adequado para otimização do impacto, tendo o objetivo final de melhorar a eficiência da descarepação do processo de laminação da empresa X.

Aug 16, 2017

By Elton Douglas Heriger Pereira

Refratários de alta alumina apresentam boa refratariedade, elevada resistência mecânica em altas temperaturas, boa resistência à variação bruscas de temperatura sem se romper sendo utilizados em revestimento de panelas e válvulas siderúrgicas devido sua propriedade anfótero e ter aplicações sobre à ação de escórias básicas. Neste trabalho procurou-se avaliar o efeito de adições de 1,5; 3,0 e 4,5%p. de Nb2O5 em refratário de alta alumina, estes obtidos a partir de uma mistura de diversos tipos de alumina, 5,0 %p. ZrO2 nanométrica (TZ-8Y) e agregado de mulita, sinterizados em temperaturas de 1400 e 1600 °C. Como nestes refratários a ZrO2 não surte o efeito de microtrincamento, a formação de fase vítrea a partir de Nb2O5 e a incorporação de agregados ao refratário foram fundamentais nas propriedades obtidas. Foram avaliadas propriedades tecnológicas como densidade e porosidade aparente pelo método de Arquimedes, formação de fases por difração de raios-X e análise microestrutural por microscopia eletrônica de varredura e resistência ao choque térmico.

Oct 30, 2017

By Manoel Inácio dos Reis Neto

Redução no consumo específico (KW/t) de energia elétrica em um dos moinhos de bauxita na refinaria da Alumina na CBA (Companhia Brasileira de Alumínio do grupo Votorantim Metais) através do uso da Metodologia Six Sigma e ações de substituição do óleo mineral por óleo sintético de alta performance, implantação do sistema de blindagem e de resfriamento no redutor deste moinho, onde foi alcançado um resultado de 5,45% de redução neste consumo específico e de 25% na temperatura de trabalho deste redutor, superando as expectativas inicias previstas.

Jul 31, 2018

By Estevesson Ferreira Miqueletti

Neste trabalho, tiras de cobre foram laminadas para se obter tubos aletados. As variáveis importantes ao sucesso do projeto foram: a) a temperatura de tratamento térmico e b) a largura da tira. Tiras largas resultaram em pouca união, levando a escolha de tiras menos largas. Temperaturas altas também resultaram em baixa união. A melhor condição foi tiras de 100 mm de largura e 500°C de tratamento térmico.

Aug 16, 2017

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Renan Celestino Silva Santos

O presente estudo trata da análise de falha de um cabo de aço utilizado em grua de construção civil. Para a análise da falha foram feitas metalografia, microdureza, análise dimensional e análise por microscopia eletrônica de varredura. Também foram feitos ensaios de tração, a fim de determinar a diminuição da resistência mecânica em decorrência de diminuição de área do cabo. A análise em campo detectou a presença de um dispositivo de acionamento do motor da grua que mantinha contato com o cabo e foi o responsável pela falha. Os resultados demonstraram que todos os fios estavam desgastados. Na maioria dos fios foi detectado aspecto de fratura plana frágil. A análise metalográfica e de microdureza não indicaram nenhum defeito metalúrgico nos cabos. Os resultados do ensaio de tração indicaram a diminuição significativa da resistência mecânica devido à redução de seção dos fios.

Aug 16, 2017