Search Documents

By J. W. Byrkit

Design features and operating methods at the new Ajo smelter are described in detail. Successful operation of a novel method of handling and charging wet concentrates to a deep bath type reverberatory furnace contribute to the daily production of 200 tons of anodes with good results from the standpoint of both metallurgy and economy. THE New Cornelia Branch of the Phelps Dodge Corp. is located at Ajo, Ariz. Large scale mining operations were started at Ajo in 1917, when a 5000 ton leaching plant was put in service to treat the copper carbonate ore that overlaid the sulphide ore-body. In 1924 a 5000 ton flotation plant was built to treat the sulphide ore and the leaching operation was abandoned a few years later. Changes in practice and additions to plant facilities have resulted in a gradual increase in the milling rate which now approaches 30,000 tons daily. Prior to the erection of the Ajo smelter, flotation concentrate was shipped by rail to Douglas, Ariz, where it was treated in the Phelps Dodge smelter. Construction of a one reverberatory furnace smelter to produce an average of about 200 tons per day of copper anodes at Ajo was started early in 1949. Initial heating of the reverberatory furnace was begun on June 21, 1950. Charging the furnace was started on july 8, and the first anodes were cast on July 14. Neither the anode furnace nor the reverberatory furnace has cooled since the initial firing. Fig. 1 is a photograph of the new smelter. Built primarily to eliminate the '300 mile haul of concentrate to the Douglas plant, the new smelter was designed to treat the Ajo concentrate, with a minimum of capital investment. A novel, and relatively simple, method of concentrate handling and furnace charging made unnecessary the installation and operation of expensive storage facilities and reclaiming equipment, and obviated the necessity of holding in storage large quantities of copper-bearing materials. (Patents are pending in the United States and abroad on the Ajo process.) In the selection and arrangement of equipment, consideration was given to the full utilization of all smelting facilities, reducing the amount of idle equipment to a minimum. The layout of the smelter is shown in Fig. 2. The important problem of internal transportation was minimized by arranging the reverberatory furnace, converters, and anode furnace in a compact group and providing storage bins inside the smelter building, within reach of overhead cranes, for fluxing materials and other supplies needed in the daily operation. This can be seen in the sectional view of the smelter given in Fig. 3. Incorporated in the design were many innovations in smelting equipment intended to facilitate operations and effect economies in maintenance expense and manpower requirements. Table I gives operating data of the entire plant. Metallurgy The metallurgical practice at Ajo is based essentially upon the use of a single, deep bath reverberatory furnace for smelting wet concentrate, without concentrate storage facilities. The large reservoir of slag and matte maintained in the furnace serves to equalize, to some extent, the day to day variations in the nature and grade of concentrate and permits

Jan 1, 1954

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 27 countries: the 12 nations of the European Community (Belgium, Dermark/Greenland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, and the United Kingdom); 6 of the 7 nations of the European Free Trade Association (Austria, Finland, Iceland, Norway, Switzerland, and Sweden); Malta; the 8 Eastern European economies in transition (Albania, Bulgaria, Czechoslovakia, Hungary, Poland, Romania, and Yugoslavia); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Community (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to the more minerally endowed countries in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). Western Europe has significant reserves of industrial minerals but has limited availability of metalliferous raw materials. It, therefore, imports significant quantities of the latter and ranks along with the United States and the U.S.S.R. in the production of refined metals. Nonetheless, there is an inherent tendency to underestimate the importance of Western Europe in the world of minerals, both as a minerals processor and raw materials buyer. The reason for this is that Western Europe is generally thought of on the basis of individual nations rather than as a whole. Viewed in this limited context, the United States, the U.S.S.R., and Japan appear to dominate the world economy. Viewed as one regional area, however, Western Europe includes the fourth (FRG), fifth (France), sixth (United Kingdom) and seventh (Italy) largest economies of the world, all bordering on one another. With the remaining 15 EC and EFTA countries, Western Europe has a land area approximately 40 % of that of the United States, exceeds the U.S. population by 50 % and has a gross domestic product about the same as that of the United States.

Jan 1, 1993

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By Warren Howes, A. B. Campbell, W. H. Ode

"INTRODUCTION The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation.The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry, Missouri School of Mines and Metallurgy, and Will H. Coghill, supervising engineer of the ore dressing section of the United States Bureau of Mines.ORIGIN OF ACID MINE WATERSRain water, carrying oxygen and carbon dioxide in solution, finds its way into the pores and crevices of the earth's crust and percolates downward through the rocks. This water and its dissolved gases exert a solvent action on many minerals, the extent of which depends upon the nature of the associated minerals.The iron sulphides are the chief sources of the 'trouble with sulphates and sulphuric acid because they oxidize so freely and contain more sulphur than is required to satisfy the iron when ferrous sulphate is formed. Galena and sphalerite may oxidize to sulphates without liberating acid. A few of the common reactions occurring in the Tri-State mine waters may be illustrated by the following equations:"

Mar 1, 1932

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By Marcos Paulo Kohler Caldas

Após a edição da RoHS Directive 2002/95/EC, diretiva que entrou em vigor em 1º de julho 2006 proibindo a utilização de seis substâncias perigosas: chumbo, mercúrio, cádmio, cromo hexavalente, bifenilos polibromados e éteres difenil-polibromados, fabricantes de equipamentos eletroeletrônicos passaram a utilizar soldas livres de chumbo (lead free) para montagem de suas placas de circuito impresso. A SAC 305 é um tipo de solda muito utilizada pelas empresas fabricantes de placas de circuito impresso. O presente trabalho visa caracterizar este tipo de solda verificando sua composição e identificar se a mesma se encontra livre de elementos perigosos ao ambiente. Avaliou-se a extração de metais como Ag e Sn através de digestão ácida em água-régia e rota HNO3 a temperatura ambiente. A composição do licor lixiviado foi caracterizada por espectrometria de emissão óptica com acoplamento de plasma induzido (ICP-OES). Os resultados indicam que a solda SAC 305 atende a RoHS, possui 2,7% Ag, 96,4% Sn e 0,9% de outros metais e a melhor rota para extração de Ag foi a HNO3 e para Sn foi a água-régia.

Aug 7, 2018

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By X Liu

The crystal chemistry of carbonate in Ca apatites, including Na-free and Na-bearing hydroxylapatite (CHAP) and Na-bearing fluorapatite (CFAP) and chlorapatite (CCLAP), has been investigated by Fourier transform infrared (FTIR) spectroscopy and single-crystal X-ray structure, using crystals synthesised from carbonate-rich melts at 1 GPa, 1400 - 1000¦C. The carbonate ion substitutes for both the X (OH, F, Cl) anion species in the apatite channel (type A carbonate) and the phosphate group (type B carbonate). The type A carbonate ion is oriented in the channel with two oxygen atoms close to the c-axis, and the type B carbonate ion is located close to the sloping faces of the substituted phosphate tetrahedron, with details varying with composition series. Sodium promotes the uptake of type B carbonate and also has a profound effect on FTIR spectra. Crystal compositions correspond approximately to the substitution formula Ca10-(y+z)Nay z[(PO4)6-(y+2z)(CO3)y+2z][X2-2x(CO3)x], with x + y up to 1.0 and z + 0.0 for CHAP, x + y + 4z + 0.4 for CCLAP, and x + y + 2z + 0.1 for CFAP, for equivalent conditions of synthesis. The sodium cation and A and B carbonate ion defects are locally coupled in all three composition series to facilitate charge compensation and minimise the effects of spatial accommodation. Synthetic Na-bearing type A-B CHAP with x + y + 0.5 has a similar chemical composition and FTIR spectrum to biological apatite.

Jan 1, 2008

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased or decreased), and provides a bridge where possible from the old Schedule A classification sys tem to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high speed photography to better understand the mechanisms of fracture and fragmentation.

Jan 1, 2015

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By C. G. Maier

The fundamental chemistry of zinc smelting, especially that part dealing with the chemical reduction of the zinc-oxide content of a roasted zinc ore, has been discussed by metallurgists in some detail, but, in the light of present knowledge, unsatisfactorily. A considerable portion of the information available has been qualitative, or quantitative in a sense that could not be interpreted chemically. A number of attempts to elucidate the physical chemistry of zinc oxide reduction have been based upon unsubstantiated and, as is now known, incorrect equilibrium data. To write upon the chemistry of zinc smelting at this time, when electrolytic methods for the production of zinc metal from ore are becoming increasingly widespread, may seem a belated effort. So, for example, C. A. Hansen,3 in the communicated discussion of an article by the author,4 writes as follows:

Jan 1, 1930

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By J. F. Barkley

Under the procedure of the American Standards Association, with the American Society for Testing Materials as sponsor, the Sectional Committee on Classification of Coals has arrived at the classification of coals by rank as shown in Table 14/. The standard explains the term "agglomerating" used for classification under physical properties, as follows: Agglomerating Index. - Coals which in the volatile-matter determination produce either an agglomerate button that will support a 500-g weight without pulverizing, or a button showing swelling or cell structure, shall be considered agglomerating from the standpoint of classification.***. Pending the adoption of a method by the American Society for Testing Materials, the coke-button grading test5,/ afforded by the examination of the residue in the platinum crucible incident to the volatile matter determination, shall be used.

Jan 1, 1937

By A. J. Williams, T. N. Croft, M. Cross

"The computational modelling of extrusion and forging processes is now well established. In this work a novel approach is described which utilises finite volume methods on unstructured meshes. This technique can be used to solve simultaneously for fluid flow, heat transfer and non-linear solid mechanics and their interactions. The approach involves the solution of free surface non-Newtonian fluid flow equations in an Eulerian context to track the behaviour of the workpiece and its extrusion/forging, and the solution of the solid mechanics equations in the Lagrangian context to predict the deformation/stress behaviour of the die. Some preliminary examples of this approach will be discussed.IntroductionThe computational modelling of extrusion and forging processes is now well established. Within the last 20 years the finite element method has become the most commonly used technique to simulate metal forming processes [1]-[4]. The Lagrangian and Eulerian type of formulation have been the two major approaches to this problem.Lagrangian methods are efficient and suitable for handling non-linear problems in which small strains prevail, boundary conditions do not change with the course of deformation, and where mesh distortion is not a critical factor in the analysis. Unfortunately, the above points are essential to any accurate metal forming analysis. The problems of mesh distortion and element entanglement pose a serious drawback on the use of such methods. Some automatic remeshing techniques have been developed for Lagrangian finite element analyses of metal forming problems [5]-[7]. However, these methods are not robust and efficient enough to remedy the mesh distortion problems in general. An alternative is to update the mesh manually but this is not always possible, and even when it is feasible it involves major interaction by the user. In addition, remeshing is usually applied to the whole domain which is not necessary and increases CPU time. The complexities associated with remeshing also affect the ability to parallelise the code."

Jan 1, 2001