Search Documents

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By J. G. Kura, P. D. Frost, L. W. Eastwood

THE preparation and general properties of mag-nesium-lithium base alloys have been described in earlier papers.l,2 Lithium forms solid solutions with pure magnesium, lowers its density, and improves its formability. The improved isotropy and better formability of these alloys are attributed to the ability of lithium to convert the magnesium lattice from hexagonal (alpha phase) to body-centered-cubic (beta phase) structure. This change in structure is, however, accompanied by some limitations which make it difficult, if not impossible, to combine all the desirable properties in one composition. The most important of these limitations is the tendency of the high-strength alloys to overage and lose strength at temperatures of the order of 150" to 200°F. A study was made of the effects of composition and heat treatment on the age-hardening character- istics of the alloys. Stability of properties was determined by hardness and tensile testing of the alloys at room temperature after various periods of exposure to elevated temperatures. Precipitation-hardening curves are shown for a number of magnesium-lithium-zinc alloys in fig. 1. All the alloys were solution treated at 700°F and aged at 200°F. The reason for using the drastic quench, toluene at —105°F, was to reduce the rapid precipitation of the hardening phase which takes place at room temperature. Previous experience has shown that a hardness of about 90 to 95 Rockwell E is indicative of yield strengths in the range of 35,000 to 40,000 psi. This is a desirable strength level for magnesium-lithium base alloys with specific gravities of the order of 1.65 or less. Although the hardness level is raised by large zinc contents, a corresponding decrease in the cold formability of these alloys occurs with increasing zinc content. Thus, alloys containing up to about 10 pct Zn and having hardnesses of the order of 70 to 75 Rockwell E may be bent over a very small radius; however, the 16 pct Zn alloy requires a bend radius of more than 8T. The hardness relationships illustrated in fig. 1 can be explained by the partial phase diagram shown in fig. 2. The zinc-free magnesium-lithium alloys are entirely body-centered cubic (100 pct beta phase) when the lithium content of the binary is 10.3 pct or higher. When zinc is added, the boundary between the beta and alpha-plus-beta fields at 700°F is shifted to lower lithium contents. In addition, the solubility of zinc at 700°F decreases with decreasing lithium content. It is shown by a study of micro-structures that the limit of solid solubility of zinc in the 6Mg/Li* matrix at 700°F is about 19 pct. It is believed from a study of the aging curves that this limit is about 2 to 3 pct at 200°F. Zinc additions up to about 2 pct increase the hardness and strength of the magnesium-lithium base solid solution. Larger additions of zinc effect further hardness increases, but precipitate during prolonged aging at 200°F. Alloys having 14 to 20 pct Zn precipitation harden extremely rapidly during quenching, even when quenched in toluene at —105° F. The high-zinc alloys overage at 200°F but are capable of maintaining reasonably high hardnesses for periods up to 1000 hr.

Jan 1, 1951

By T. Rosenqvist

From the chemical, metallurgical, and mineralogical points of view, the importance of thermodynamic data for metal-sulphides and sulphur dissolved in molten metal has long been realized. Such data will give a basis for thermo-dynamic calculations of processes such as roasting and the distribution of sulphur between molten metal and slags. Furthermore, it will help us understand the chemical forces which tie sulphur to the metal and to the melt. Thermodynamic studies of solid sulphides and the equilibria between solid sulphides and metals have been carried out in a rather large number of cases by several investigators. An excellent review of this work is given by Kelley.1 On the other hand, very little is known about the thermodynamic properties of molten sulphides and of sulphur dissolved in molten metal. The only system which previously has been investigated in this respect is the iron/sulphur system. The purpose of the present investigation was primarily to obtain further data for metalisulphur melts and the system silver/sulphur was chosen, not because this system was expected to be of special interest in itself, but because the silver/sulphur system is a typical example of a metal/sulphur system. Because of the low melting temperatures, the work could be carried out without appreciable furnace and refractory difficulties. The sulphur in this system possesses a rather high escaping tendency compared to most other metal/sulphur systems. By the method employed (reaction with hydrogen to form hydrogen sulphide) this gives ratios Ph2s/Ph2 up to 0.30, which may be determined accurately. 'rhermodynamic investigations of the heterogeneous reaction Ag2S +H2 —+ 2Ag + H2S have previously been carried out by Pelabon,2 Keyes and Felsing,3 Jellineb and Zakowski,4 Wat-anabe,6 and Britzke and Kapustinsky.6 Their results are in rather poor agreement. Experimental Part PRINCIPLE In the present invehgation the escaping tendency of sulphur from the condensed phase was determined by the reaction: S + H2 = H2S The ratio Ph2s/Ph2 is at constant temperature, directly proportional to the escaping tendency of sulphur and to its chemical activity in the condensed phase. (This ratio will subsequently be denoted by H2S/H2.) From this ratio and its variation with temperature and with change in the com- position of the condensed phase, thermodyrlamic quantities such as free energy and heat of reaction can be derived. The apparatus used is shown in Fig 1. The silver/sulphur alloy was placed in a crucible inside a refractory tube and mounted inside the furnace to the left. The tube was a part of a closed, gas-tight system in which the gas mixture could circulate until equilibrium was established. Circulation was maintained by the glass propeller to the right, driven by an external magnet, and promoted by the chimney action of the furnace. The gas passed up through the furnace, down into the crucible where it came in contact with the alloy, passed rapidly up through a narrow tube and out of the hot zone. After equilibrium was established between the gas and the condensed phase, the composition of the gas mixture was determined from its density. In its circulation, the gas mixture passed through a chamber (lower right on Fig 1) containing a buoyancy-balance, where the density of the gas was determined by magnetic balancing. From the measured density,

Jan 1, 1950

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By W. A. Backofen, D. Lee

The deformation of textured sheet of titanium and several of its all-a (hcp) alloys was investigated with two kinds of experiments: tension testing along different directions in the plane of the sheet, and combined-stress loading along the principal axes of anisotropy (the rolling and transverse directions). Texture and plastic anisotropy were evaluated with pole figures and by measurement, as a function of orientation, of the tensile transverse-strain ratio, or R parameter. The results as a whole can be rationalized qualitatively with the present understanding of deformation mechanisms in titanium. Quantitative agreement between the orientation dependence of tensile yield strength and the Predictions of continuum ANISOTROPY in the properties of engineering materials is more the rule than the exception because anisotropy in structure is so common, and the one generally follows the other. Two broad categories of structural anisotropy are represented by mechanical fibering and crystallographic texture. The former is important in many aspects of fracture.' The latter has more significance for yielding and plastic deformation, theory, using the R measurements, was relatively poor. However, in tension-tension quadrants of the yield-locus diagrams, the difference between theory and experiment was hardly more than 10 pct. The maximum texture-hardening effect was found in a 4Al-1/4O2 alloy to be nearly 50 pct. In the compression-compression quadrant, {1012} deformation twinning prevented the locus from expanding much beyond the Position predicted for isotropic material. With increasing temperature the trend in R was downwards, approaching unity (isotropy) near the a-transus temperature; an accompanying development was large amounts of neck-free extension. which are of special concern in this paper. The tendency has been to view crystallographic texture more as a liability or curio than as an asset. The prominent exception is found in silicon-ferrite sheet for power-transformer cores, which is processed to develop a new optimum texture for high electrical efficiency. Yet it should be possible to find other examples, involving other kinds of properties. More specifically, there is good analytical reason to expect improved combined-stress yielding resistance in suitably textured material,2,3 and it has now been shown by experiment that texture hardening or softening is a potentially useful phenomenon in certain engineering devices and processes.'-I To date, work has included measurements of the transverse (width to thickness) strain ratios in the

Jan 1, 1967

By William B. Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chair man of the Institute's Committee on Petroleum and Gas; as a pre1iminary.discussion of the fuel oils which are used in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, I suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220" F., nor burn under 320" F. In the Southwest, it has not been long since we had fuel oils that flashed as low as 110" F., and the average flash point over a considerable period was 151" F. Now we are using oil that flashes at about 30" lower than the former burning point, which was 258" F. In other words, the flash point has risen, on the average, 100"; and the burning point about 75".

Jan 1, 1915

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

By J. P. Lesley

The Pittsburgh coal-region, if we regard the greatness of its extent, the picturesque beauty of its scenery, the salubrity of its climate, its relative situation on the Continent, the fertility of its soil, its unrivalled mineral wealth, and its magnificent system of natural transportation, is, perhaps, the most valuable spot on the surface of the planet. Unlike the mythical Paradise inhabited by one man and one woman, it swarms with an abounding population, not living on the free gifts of nature without care and without toil, hut expending its energies in unremitting labor, reinforced by the most elaborate machinery, in the production of everything which mankinds needs or desires; and unlilte the Paradise of story from which flowed the four great rivers of the world in opposite directions, its own four rivers How from the surrounding world into it, to constitute by their union the great highway water-course which divides the Northern from the Southern States. These rivers are the Monongahela, coming from the south, the Yonghiogheny from the southeast, the Kiskiminetas from the east, and the Allegheny from the north. Uniting at the great city of pittsburgh, they constitnte the Ohio, which flows northwest and west, and then south and southwest, toward the Mississippi. The Monongahela has been made navigable by a system of dams and pools the Allegheny was navigable in its natural condition; the KisKiminetas was made navigable by a State canal which has been vacated ; and the Youghiogheny remains unnavigable. Railroads supplement the deficiencies of the rivers, follow their hanks, and share in the transportation for which the waters are not sufficient. Railroads and rivers concentrate at Pittsburgh; other railroads cross the highlands to the east and west; and branch roads ascend the side-valleys and ravines to the mines on the uplands. The whole region is a scene of life; towns and villages dot its surface in all directions ; hundreds of gangways open upon the sides of all the valleys, and deliver coal to trains of cars which move beneath them at water-level; furnaces and rolling-mills abound; hundreds of oil-wells furnish a flood of liquid fuel to pipe-lines

Jan 1, 1886

By William Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chairman of the Institute's Committee on Petroleum and Gas, as a preliminary discussion of the fuel oils which are used-in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, J suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220° F., nor burn under 320° F. In the Southwest, it has not been long since we had fuel oils that flashed at as low as 110° F., and the average flash point over a considerable period was 151° F. Now we are using oil that flashes at about 30° lower than the former burning point, which was 256° F. In other words, the flash point has risen, on the average, 100°; and the burning point about 75°.

Jan 6, 1914

By Hobart M. Kraner, E. B. Snyder

THIS paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, particularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercial blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. FACTORS AFFECTING CHOICE OF REFRACTORIES If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing temperature, which he in turn interprets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and resistance to the action of slag. In most refractory applications several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient stages and the progress is determined by measuring slight changes in. porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures . at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. -Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

By Samuel G. Vera

INTRODUCTION The Climax Mine is a property of Climax Molybdenum Company, a division of AMAX Inc. Climax is located in the central part of the Colorado Mineral Belt on the west slope of the Tenmile Range, Lake County, Colorado at 3,425' m. above sea level. Climax Mine, the largest single producer of molybdenum in the free world, has been a cornerstone of mining in the State of Colorado for many years. Before molybdenum was known, the early hunters of gold and silver laid their hands on the outcrops of the Climax deposit and left it as low quality lead or graphite without much value. Today, 44,000 TPD of ore is extracted from the heart of Bartlett Mountain. The molybdenum, separated from the ore, is vital for mankind, being used for everything from fertilizer to fine components of aerospace ships, because of its valuable physical and chemical properties. The operations at Climax have never remained static. Constant demand for the "gray gold", and technological advancements, have converted Climax into an "open book of technology", where learning the still-hidden secrets of mining is a continuing process. (All figures related to tons are metric tons) BRIEF HISTORY The mine produced its first molybdenum ore in 1918. It was shut down in 1919, resumed production in 1924, and has been in continuous production since that time. During World War 11, a peak of 20,000 tons per day was reached, then tonnage dropped from 1945 to 1950. Since 1951, production has been in- creasing, reaching a peak of 46,000 tons per day during the month of June, 1980. Early mining used shrinkage stoping. Block caving using the grizzly system was introduced in the early 1930's. Caving methods were improved through empirical studies of rock behavior and by trial and error, evolving a very efficient mining method by the late 1940's. This form of continuous retreat panel caving, with small modifications, is still used today, and has made the Climax Mine one of the biggest underground mines in the world. The Climax Mine, synonymous with molybdenum, was essentially an underground mine until 1973 when the open pit was introduced. Since then, both mining methods have operated successfully. Current production is 60% from underground, and the remaining from the open pit. Climax has been in continuous operation for 56 years, and as of December 31, 1980, more than 386 million tons of ore have been mined. The orebody is not fully defined, and at the present mining rate, the known life span of the mine will be to the year 2020. GEOLOGY The Climax deposit is a large low-grade porphyry molybdenum deposit somewhat similar to porphyry copper deposits, with a well- mineralized quartz molybdenum stock work sys- tem. It lies within the pre-Cambrian granites and schists and the Tertiary Climax porphyry. The age of mineralization is thought to be mid-Tertiary and is characterized by fracture filling and replacement through silicification. The main economic mineral is molybdenum, with pyrite, cassiterite and wolframite as by-products. Fluorite and topaz also occur, but are not recovered at this

Jan 1, 1981

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K's) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.' In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By C. Kremer Bain

UNDER present economic conditions the necessity of mechanizing the mines of our country has become a very important problem. More and more mines are looking toward increased or complete mechanization of their operations, so in the writer's opinion it is quite pertinent that some of the associated problems that accompany such a program be pointed out. The following generalization on attempting a comparatively slight change in mining methods at the Southeast Missouri properties of the St. Joseph Lead Co. is an attempt to point out to anyone faced with a mechanization program that much time and C. KREMER BAIN, Member AIME, is Assistant to General Manager, St. Joseph Lead Co., Bonne Terre, Mo. AIME Sun Francisco Meeting, February 1949. TP 2743 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Dec. 27, 1948; revision received Oct. 13, 1949. effort can be saved, and many headaches avoided, if company policy can be established whereby everyone in the organization from the top down is desirous of improvement and is working towards the common objective. Any changes in mining methods, machinery, and so on, must entah coordination of all the other phases of mining as they all have to mesh as accurately as a smooth running chain of gears if satisfactory results are to be obtained. The purpose of this paper is to point out some of the problems which :have to be surmounted when any mechanization program is attempted, rather than to go into the mechanical details and actual operating data of the equipment employed. After all, machines have to be adapted to best suit the local conditions, so no general formula can be given that would apply to other properties. Although St. Josepll Lead Co. has been mechani-cally-minded for a number of years, as shown by the fact that over 110 million tons have been loaded mechanically since 1922, any further mechanization or changes always present a problem. When our ore bodies were of great height and area the breaking and loading were developed to a high degree of efficiency according to known standards. But in recent years, when our ore bodies became smaller and more scattered, the amount of tonnage we were able to break was not sufficient to supply our shovels with enough rock to keep them working to capacity. Our first step in attempting to rectify this situation was to develop a technique of moving the shovels to the broken ore in various stopes, which sometimes entailed a move each shift. A shovel is not producing when being moved, so within the last two years we have been endeavoring to devise some means of getting more rock broken in these smaller stopes and it was then that we became interested in jumbo drilling. To illustrate the fact that mechanization is a process of a chain of developments rather than a stroke of genius can best be shown by a general summary of conditions and obstacles which were encountered in our present attempt to establish template drilling of a standardized round. Our first jumbo was more or less the conventional type with two machines mounted on a crossbar. This arrangement proved to be impractical to duplicate satisfactorily the regular routine of slabbing in a more or less radial pattern as carried out by column drilling. One machine was either too close to or too far from the face and there was another disadvantage in that one drillman was frequently delayed while waiting for his partner to bottom a hole. Our next step was to eliminate the crossbar so the machines could operate independently of each other, but we still encountered the same objections mentioned above except that one drillman was free to drill three holes instead of one in a vertical plane independently of his partner. Time studies while trying to adapt the jumbo to the regular slabbing practice as accomplished by column drilling, revealed that twice as much time was spent in maneuvering the jumbo into position and aligning the holes as was consumed in drilling.

Jan 1, 1951

By Dennis S. Kostick

Introduction Soda ash is known chemically as sodium carbonate, an important inorganic chemical. It has been produced for several centuries by processing certain vegetation and minerals. The US soda ash industry has evolved from several small sodium carbonate mining operations in the West. Now, a nucleus of six companies produce about one-fourth of the world's annual soda ash output US producers currently dominate the world market. But certain international events are occurring that will reshape the domestic soda ash industry in the next decade. Historical perspective Soda ash is used mainly in the manufacture of glass, soap, dyes and pigments, textiles, and other chemical preparations. All of these are the first basic consumer products produced by developing societies. About 3500 BC, the Egyptians became the first society to use crude soda ash. The soda ash was used to make glass containers. It was most likely obtained from dried mineral incrustations around alkaline lakes. Soda deposits were virtually nonexistent in western Europe. So people resorted to burning seaweed to obtain the ashes. The ashes were then leached with hot water and the solute was recovered after evaporating the solution to dryness. The solute, a crude "soda ash" was impure. But, it could be used to make glass and soap. These two products and industries were important to the population and economic growth of the region. About 11.5 t (13 st) of seaweed ash was required to produce about 0.9 t (1 st) of soda ash. Along the coasts of England, France, and Spain, seaweeds with varying alkali contents became important items of commerce and sources of soda ash before the 18th century. The LeBlanc process used salt, sulfuric acid, coal, and limestone. It became the major method of production from about 1823 to 1885. In the early 1860s, Ernest and Alfred Solvay, two Belgian brothers, successfully commercialized an ammonia-soda process to synthesize soda ash. It used salt, coke, limestone, and ammonia. The Solvay process produced a better quality product than the LeBlanc method. In 1879, Oswald J. Heinrich presented to the Baltimore meeting of AIME, a paper entitled "The manufacture of soda by the ammonia process." The paper compared the two processes and foretold the demise of the LeBlanc technique. World production of soda ash in 1880 was 680 kt (750,000 st). Of that, 544 kt (600,000 st) was produced by the LeBlanc process. Of the 2.8 Mt (3.1 million st) of soda ash produced worldwide in 1913, only about 50 kt (55,000 st) was by the LeBlanc method. The LeBlanc process was never used successfully in the US, except for a brief period from July 1884 to January 1885 in Laramie, WY. Previously, soda ash had been produced by burning certain plants, as exemplified by the early Jamestown colonists, or by recovering small quantities of natural sodium carbonate found in alkaline lakes, such as those found near Fallon, NV, and Independence Rock, WY. Before the 1884 startup of the first synthetic soda ash plant in the US at Syracuse, NY, most of the domestic soda ash demand in the East was met by imports, primarily from England. Large-scale commercial production of natural soda ash began in California in 1887 from surface crystalline material at Owens Lake. Production from sodium carbonate-bearing brines at Searles Lake began in 1927 (Fig. 1). In 1938, during exploration for oil and gas in southwestern Wyoming, a massive buried trona deposit, presumably the world's largest, was accidentally discovered. Recent mineral resource evaluation by the US Geological Survey and the US Bureau of Mines indicates that the Wyoming trona deposit contains 86 Gt (93 billion st) of identified trona resource in beds 1.2 m (4 ft) thick or greater. Additionally, there is about 61 Gt (67 billion st) of reserve base trona. Of this 36 Gt (40 billion st) is in halite-free trona beds and 24 Gt (27 billion st) is in mixed trona and halite beds. In 1953, the Food Machinery and Chemical Corp. (later shortened to FMC Corp.) became the first company to mine trona in Wyoming. Soda ash demand increased.

Jan 10, 1985

By J. W. Leomrd, B. A. Donahue

Results of research are presented examining the extent to which the analytical characteristics of the relatively distinct coal bands from a variety of coal seams can be related to each other. This paper dis-cusses an approach for developing a practical coal petrographic quality control program based on conventional analyses, most of which is part of the standard A.S.T.M. procedure. The work is a final follow-up to Part I of this series which was prepared by the authors as an approach to applying conventional coal petrography to single coal seams. Recent published work by the authors entitled Petrography for Coal Mining and Coal Prepration: Part I dealt with interrelating various chemical and physical properties of coal1 measured using conventional analyses made on distinct petrographic bands taken from single coal seams. Since most coal production facilities process coal from a single coal seam or from very closely related coal seams in the same area,2 emphasis on interrelating the properties within a single seam appeared appropriate. The distinct petrographic bands were analyzed on the assumption that such differentiated data would be more representative of a heterogeneous coal seam than the single analytical value commonly used to characterize each property of an entire seam.34 Effort was directed at demonstrating the extent to which the interrelated chemical and physical properties 5,6 could be developed into nomographs or petrographic standardization graphs. Thus, one analysis, determined on a series of petrographic fractions separated from a single sample, was used to estimate numerous other properties in each fraction by referring to the previously established petrographic standardization graphs. This conventional approach to coal petrography was undertaken as a suggested feasible means by which a few coal analyses could be employed to develope a more penetrating knowledge of the properties of coal from any given seam in order to monitor more extensively its performance at the point of utilization. Such procedures can support development of the type of in- formation commonly sought through automated testing and through the use of computers.7 The broad knowledge which can be developed through these procedures is intended for application in the generation of an analytical profile or broad characterization of coal. These estimates were not intended as replacements for individual coal analytical tests. In this expanded second part of the research program, distinct petrographic bands from nine coal seams in the Central Appalachian Region were physically and chemically analyzed to elucidate the extent to which this concept of conventional petrography could be broadened for application to numerous coal seams. In presenting this second phase of work, the relationships developed are presented individually and not in a connecting series of nomographs or petrographic standardization graphs as in the previous work, thus leaving open the combinations of possibilities to individual interpretation and application. MATERIAL AND EXPERIMENTAL WORK Nine coal seams, representing a wide range of rank, from the Central Appalachian coal fields were used in this study. The distinct petrographic bands from the Kittanning, Pond Creek, Jawbone, Tiller, Poca-hontas No. 3, No. 2 Gas, Eagle, Winifrede, and Pittsburgh coal seams were separated by carefully removing a portion of each band at the face of the seam. The following were determined: ash, sulfur, free swelling index, heating value, bulk specific gravity, volatile matter, Hardgrove Grindability Index, and Gieseler Plastometer measurements. Determinations, where procedures were available, were carried out using ASTM standard procedures.8 Bulk specific gravity was determined using a kerosene volume displacement procedure modified from a method applied by Headlee and McClelland of the West Virginia Geological survey,9 Those bands with a bulk specific gravity greater than 1.60, which is generally above the practical specific gravity cleaning range of bituminous coals, were excluded and no analyses were performed. Much of the initial organization of this second phase of work was developed through the extensive use of a computerized statistical monitoring program (see Ref. 4). However, in order to achieve the closest possible interpretation of results, the final organization of data proceeded mainly from exhaustive trial

Jan 1, 1968

By D. Muraoka

Introduction Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Basin of southwestern Wyoming. Stauffer Chemical Co. of Wyoming, a jointly owned subsidiary of Stauffer Chemical Co. and Rocky Mountain Energy Co., mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of about 1.8 Mt (2 million st) per year of soda ash. The refinery has five parallel operating trains using the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with refinery feed (less than peagravel size material) entering the process. Oversize is conveyed to an outdoor stockpile. Ore is recycled from under the stockpile via cone feeders as the refinery needs require. The ore is conveyed to hammer type crushers and screened. The refinery feed enters the process and the oversize is recycled to the crushers. Calcining The first step in refining trona to soda ash is calcining the trona ore. This is accomplished in concurrent flow, rotary kilns that are direct fired with natural gas. [2 (Na CO NaHCO 2H O) Heat 3Na CO + 5H20 + CO 2 3~3~ 2 ~~2 32] The trona ore is fed to the kiln at the burner end and is intimately mixed with the hot exhaust gases from the burner. Direct contact with the flame is avoided. The ore moves down the kiln by gravity and rotation aided by the kiln's internal lifters. The exhaust gases are cleaned to 99 + % particulate removal and discharged to the atmosphere. Dissolving the Calcined Trona The calcined trona is conveyed from the kiln discharge to a rotary drum dissolver where it is mixed with water and weak solution (unsaturated solution of calcined trona in water). The calcined trona is soluble whereas the impurities, primarily shale, are insoluble. The discharge from the dissolver is a slurry containing saturated solution (about 30% dissolved calcined trona in water), some undissolved calcined trona, insoluble impurities, and organic impurities. The dissolver discharge enters a rake classifier that makes the first solid/liquid separation in the process by removing the heavy undissolved material from the saturated solution. This undissolved material is conveyed to a second rotary drum dissolver and mixed with water to dissolve any remaining calcined trona. The secondary dissolver discharges to a second rake classifier that separates the solids from the liquid. The solids are now primarily insoluble impurities with very little unrecovered calcined trona. These wastes are conveyed to evaporation ponds for disposal. The liquid from the secondary rake is recycled to the primary dissolvers' weak solution system. Returning to the primary rake classifier, the saturated solution which contains suspended insoluble muds is pumped to a thickener. Flocculant is added to aid settling of the suspended muds. The flocculated muds are collected at the bottom of the thickener and pumped to vacuum cloth filters. The adhering saturated solution is separated from the muds that remain on the filter cloth. The recovered solution is returned to the dissolvers' weak solution system. The muds are reslurried and pumped to the evaporation ponds for disposal. Saturated solution, containing some suspended insoluble muds along with the organic impurities, overflows the thickener. Filtering the Saturated Solution The saturated solution overflowing the thickener enters a holding tank where it is pumped to a bank of pressure leaf filters. The suspended muds are captured on the filter leaves while the cleaned saturated solution is pumped to polishing filters. The polishing filters are also leaf pressure type, intended to remove any suspended solids that may pass the primary filters. Organic impurities are removed with activated carbon. The purified solution is now free of insoluble muds and has most of the organic impurities removed. Crystallizing and Drying the Monohydrate The purified saturated solution is pumped to evaporative crystallizers. The solution is circulated from the crystallizer vessel through a heat exchanger. Indirect contact with steam in the heat exchanger causes the saturated solution to boil, thus crystallizing the soda ash in its monohydrate form. Slurry crystal density is maintained in the crystallizer by simulta¬neous feed of fresh saturated solution and drawoff of the slurry.

Jan 1, 1986