Search Documents

By Fuad S. Maayeh, Robert J. Evans, Paul M. Yavorsky

A description and capabilities of the Mine Roof Simulator at the Pittsburgh Mining Technology Center is illustrated for testing longwall roof support equipment. This unique Mine Roof Simulator has the capacity to exert 3 million lbs. of compressive force vertically and 1.6 million lbs. of force horizontally to simulate loads on hydraulic supports typically found in longwall mining. The supports that undergo testing are instrumented with strain gauges and photoelastic coatings such that critically strained areas become readily apparent. These critically strained areas are redesigned or retrofitted with appropriate reinforcement and retested. A data base will be accumulated from several support designs that will lead to an optimized design that will have the potential to reduce downtime by malfunctions of supports and thus increase productivity. A typical test procedure and analysis is given for a two leg 350 ton shield along with a description for placement of strain gauges, displacement gauges, and hydraulic pressure monitors for critical sites.

Jan 1, 1982

The Kaltails Project is situated close to the city of Kalgoorlie-Boulder in Western Australia. Located on the south-eastern fringe of the Golden Mile, Kaltails has been in operation since June 1989. The tailings forming the reserve for Kaltails have been derived from 100 years of underground mining on the Golden Mile, but, some of the re.;erve has been retreated in the past. A map of the tailings reserves and treatment plant site is presented as Figure 1. The gold project is a joint venture between Poseidon 90 per cent and Gold Corporation (ten per cent) and is managed by Poseidon Gold Kaltails.

Jan 1, 1992

By Arash Saeidi Rashk Olia, Dunja Perić

The increasing demand for renewable energy has attracted attention to energy geostructures as means of extracting clean geothermal energy from the ground. To further advance the understanding of soilstructure interaction in energy piles analytical solutions considering the self-weight of the pile were derived. These solutions were then incorporated in recently-derived thermomechanical weightless solutions to provide comprehensive analytical solutions for axial displacement, strain and stress in single energy piles. This was accomplished by comparing responses of energy pile under different loading scenarios that reflect presence and absence of the self-weight. Results of mechanics-based analysis revealed that the self-weight of energy piles embedded in stiff soils has no significant contribution to displacement, strain and stress that develop under thermo-mechanical loads. Overall, the significance of the self-weight contribution depends on the magnitude of thermal load as well as the soil-pile interface stiffness. The stiffness of end restraints imposed to the pile head and tip were also found to play an important role in contribution of self-weight in induced thermomechanical stresses in energy piles.

Oct 1, 2022

By Terzis D. PhD, Katterbach M.

While awareness around the environmental impact of existing grout materials and chemical binders is increasing rapidly, biotechnologies are growing traction as sustainable alternatives in groundwork operations. Herein we present the principles and application methods of bio-grouting. The term is used to describe a system which is based on soil, groundwater or marine enzymes which are able to catalyze the production of calcite replicating a natural phenomenon. The system’s end result are mineral crystalline bridges which act as binders to improve the geotechnical properties of soils. This paper presents a comprehensive description of bio-grouts, their underlaying mechanisms contributing to mineralization as well as environmental considerations. With their water-like rheology, bio-grouts have a wide application range and are minimally invasive, requiring only very limited injection pressures. The equipment is the same as that used in conventional cement grouting, and the reactant components are worldwide available or easily suppliable, which explains why bio-grouting has nowadays become a valuable and sustainable alternative towards efficient soil treatment. Recent developments in the last years have allowed to further increase the applicability and efficiency of bio-grouts to ultimately bridge the gap between research and practice. A case study is illustrated in this paper showing the successful implementation of bio-grout for the stabilization of weakly cemented sandstone to safeguard an adjacent road segment in Switzerland

May 1, 2022

By D. A. Baker, E. A. Gyawu, K. Awuah-Offei

Several underground coal mining disasters, such as Upper Big Branch in 2010, have revealed technological and organizational shortcomings related to self-escape. Efforts to address these gaps have primarily been top-down, that is, identified and implemented by upper management or external governing bodies. In contrast, this study employs a novel miner-centered approach to identify perceived technological boundaries to self-escape. Using a semi-structured, scenario-based survey, we elicit direct feedback from miners about current, emerging, and hypothetical technologies aimed at improving self-escape during mine emergencies. The results show a general high usefulness rating across all 21 technologies in the survey. Miners who work underground (both outby and working face miners) appear to give higher usefulness ratings overall than miners on the surface and other locations. This work will be directly applied to a series of proof of concept and prototype studies on self-contained self-rescuers (SCSRs), refuge alternatives (RA), and communication devises aimed at improving self-escape technologies through miner-centered research and design.

Mar 2, 2022

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By M. Meckkey El Sharnouby

In this paper, the results of full-scale field testing of reinforced helical pulldown micropiles (RG-HSP) installed in clayey till soils and resting on sandy soils are presented. Piles were tested under monotonic and two way cyclic lateral loadings. Effect of different loading setups on the results is demonstrated. The factors affecting the piles' performance are discussed. It was found that under monotonic loading the piles were able to sustain displacement up to 50% of the grout shaft diameter. Under low cyclic loading levels, the piles did not suffer degradation in the performance. Also, the degradation rate during cyclic loading increased with the increase of the load level. The experimental results show that the reinforced helical pulldown micropile is a reliable foundation option for lateral monotonic and cyclic loading applications.

Jan 1, 2011

By Seyed Ahmad Jenabali-Jahromi

In this paper a meshless method called Finite Point Method (FPM) is developed to simulate the solidification process of continuously cast bloom steel in both primary and secondary cooling region. The method is based on the use of a weighted least-square interpolation procedure. A transverse slice of bloom as it moves with casting speed is considered as computational domain. The two dimensional heat transfer equation together with temperature dependent thermophysical properties is solved in the computational domain. The present work is verified in the mold region by the comparison of the surface temperature simulated by FPM and finite volume method (FVM) and also comparison of solidified shell thickness simulated by FPM and measured on a breakout bloom. For secondary cooling region the validation is done by comparison of the surface temperature simulated by FPM, FVM and thermovision measurements.

Jan 1, 2009

By AIME AIME

Report of Committee 24, of the International Association for Testing Materials, presented at the Brussels Congress, 1906. Republished for use at the 94th Meeting of the American Institute of Mining Engineers, New York, N. Y., February, 1908. Discussion by letter is requested by the Secretary of the Institute. The Committee appointed for the solution of Problem 24 consisted of the following members Prof. H. M. Howe, New York, N. Y. (Chairman); L. Levy, Paris, France (Vice-Chairman) ; Prof. D. Tschernoff, St. Petersburg, Russia (Vice-Chairman) ; Prof. Albert Sauveur, Cambridge, Mass. (Secretary) ; Van Drunen, Ixelles, Belgium; Lieut.-Col. H. Tusen, Copenhagen, Denmark ; E. P. Martin, Abergavenny, England ; A. Pourcel, Paris, France ; H. Brauer, Dortmund, Germany ; Dr. Prof. H. Wedding, Berlin, Germany; P. Verole, Milan, Italy ; A. Baalsrud, Christiania, Norway ; A. R. v. Dormus, Vienna, Austria ; A. Sailler, Vienna, Austria; Bureau des Forges, St. Petersburg, Russia; Prof. N. Belelub-sky, St. Petersburg, Russia ; N. Jossa, St. Petersburg, Russia ; Maj.-Gen. M. Korobkoff, St. Petersburg, Russia ; S. Smirnoff, St. Petersburg, Russia ;.Ladislaus v. Tetmajer, Budapest, Hungary ; H. H. Campbell, Steelton, Pa. Early in February, 1905, a list of species and varieties of iron and steel, with definitions, drawn by the Chairman and Secretary of Committee 24, was sent to every member of this Committee with a request for comments and suggestions. A special request was sent to the following gentlemen . for the equivalents in their several languages of these species and varieties : A. , Pourcel, Paris, France; Prof. H. Wedding, Berlin, Germany ; J. A. Brinell, Stockholm, Sweden ; Prof. H. I. Hannover, Copenhagen, Denmark; Prof. P. Kley, Delft, Holland; P. Verole, Milan, Italy; Col. Cubillo, Trubia, Spain. This present report, which is based upon our original list and definitions, and upon the replies to these requests, consists of four parts I. A polyglot, which gives the names of the chief classes of iron and steel in English, French, German, Swedish, Danish and Dutch. We .regret that we have failed to get the Italian and Spanish names. II. English definitions of principal classes of iron and steel. III. A glossary of special sizes and shapes of iron and steel. IV. A note on the boundary between steel and cast-iron. I. POLYGLOT, IN ENGLISH, FRENCH, GERMAN, SWEDISH, DANISH AND DUTCH, OF THE CHIEF CLASSES OF IRON AND STEEL, AND OF THE APPARATUS IN WHICH THEY ARE MADE. This list is not intended to be complete, but rather to include only those varieties which are of interest to the Association.

Mar 1, 1908

By J. R. Hauger, P. A. Romans, W. J. Niebuhr

With suitable instrumentation and techniques it is possible to determine the presence of tantalum in columbium to 20 ppm . This paper discusses the selection of X- ray spectrographic instrumentation and describes a technique for accomplishing the low level determination of tantalum . An ion- exchange method of separating tantalum from columbium is also described .

Jan 1, 1964

By S. Liaghat, J. Rosenkranz, P. Semsari Parapari, S. Chehreh Chelgani, A. Tohry

It is commonly accepted that the energy consumption for comminution within mineral processing is responsible for around 3% of the global electrical energy usage. However, it was clearly noted that inside mills, less than 1% of this energy efficiency is actually consumed for particle size reduction. Therefore, monitoring of grinding parameters and modelling of product particle size distribution (e.g. characterised by the 80% passing size P80) play an essential role in operating costs of a mineral processing plant. Several empirical models have been introduced for the prediction of the P80. Since in the industrial scale usually a few numbers of grinding variables are monitored, these models cannot identically be used in plants. In addition, these empirical models do not always indicate the magnitude of correlations between milling variables. This study proposes to introduce the Hilbert-Schmidt independence criterion (HSIC) as an intelligent model for exploring linear and nonlinear relationships between grinding variables and P80 for an industrial scale data assessment. HSIC can rank variables based on their importance and help to select the most effective one for the generation of predictive models. HSIC modelling through various monitored grinding variables (ball charge, feed input rate, F80, power draw and work index) of an industrial plant indicated that F80 as a feed property has the highest effect on P80 of the ball mill products. Modelling results highlighted that the P80 can be accurately predicted, based on effective variables by using a HSIC model. These outcomes showed that HSIC as a powerful modelling tool can assess the relationships between monitored grinding parameters, select the most effective grinding parameters and satisfactorily predict the P80. Keywords: Product particle size, variable importance measurement, Hilbert-Schmidt independence criterion, mill charge

Jan 1, 2020

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By D. Minson, G. Lindner, S. Miskovic

Thickening is an essential process in the mining industry and currently one of the most costeffective technologies for recovering water from tailings streams. Improved performance of thickeners can lead to significant energy savings, and increased recovery of water close to the mill. Its performance is directly affected by the rheological properties of slurry at the raking zone. To further understand the dynamics of slurry inside thickeners, a multiphase particle-in-cell method (MP-PIC), is used to investigate its behaviour on a sliding channel. Parameters like particle-size distribution (PSD), rheological properties, and domain discretisation were benchmarked to study its influence on highly dense flows. The slurry concentration by weight of the samples ranged between 60 to 70% of solids by mass, under which conditions it is known to behave like a non-newtonian fluid. An experimental flume, 0.2 m wide and 2 m long, was used for validation under different angles and slurry composition. Visual analysis of the slurry height and shape, as well as velocity measurements, were compared with numerical data. The preliminary results show the ability of MP-PIC method to represent different types of highly dense flows, while still being computationally affordable and practical for industrial use. Keywords: High density thickener, CFD, MP-PIC, multiphase-flow

Jan 1, 2020

By W. J. González

With the increasing demand for minerals and the decline in the quality of ore reserves, technologies to maximize recovery are critical to a mine?s economic success. Many mining waters exhibit the potential to form hardness-based inorganic scales, which inhibit effective mineral recovery. Often, a continuously-fed chemical deposit control program is implemented by the mine site to inhibit these scales. The use of retractable scale coupons is the current industry standard for monitoring these programs; however, a key drawback to their use is the limited, and sometimes untimely amount of information they provide. A proprietary fouling analyzer has been developed that can be used to continuously monitor the formation of inorganic scales in mining process streams. Consequently, it can be used to continually, and more effectively, communicate the efficacy of an antiscalant program, thereby providing the ability to compare different scale control programs and to optimize their feedrates. Case studies presented validate the applicability of this technology to help optimize mineral recovery.

Feb 23, 2014

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By Linge HG, Klauber C

The key element in the carbon-in-pulp process for gold processing is the loading of dissolved Au(CN)2 from solution onto activated carbon. The mechanism and kinetics of this step have been examined by solution adsorption-desorption and X-ray photoelectron spectroscopy for both coconut derived activated carbon and peat-based activated carbon. The results show that these carbon types have the same mechanism and kinetics of adsorption. There is no contribution to the bonding from carbon-oxygen functionalities on the carbon surface, as has been invariably supposed in all previous theories for the mechanism of the reaction. It is shown that Au(CN)Z is reversibly adsorbed intact on and parallel to the graphitic planes of the carbon with the formation of a weak carbon-gold n-donor bond. The kinetic measurement of carbon gold loading reactivity is discussed and use of the Murdoch equation for this test is critically assessed.

Jan 1, 1989

By Cyril S., Smith

WE cannot but marvel at the fact that fire is necessary for almost every operation. It takes the sands of the earth and melts them-now into glass, now into silver, minium or other lead or some substance useful to the artist or physician. By fire, minerals are disintegrated and copper produced; in fire is iron born and by fire is it subdued; by fire, gold is purified; by fire, stones are burned for the binding together of the walls of houses.... Fire is the immeasurable, uncontrollable element, concerning which it is hard to say whether it consumes more or produces more." Thus wrote Pliny in his "Natural History," that great collection of fact and error which constitutes the principal contemporary description of Roman technology and which until the seventeenth century was the authority most often quoted and requoted by those who wrote on metals, as on many other subjects.

Jan 1, 1940

By W. J. Miles

Diatomaceous earth or diatomite is a sedimentary rock of organic origin that is composed principally of the silicious skeletal remains of diatoms. Diatoms are microscopic single cell acquatic plants that are related to algae. Diatoms first became abundant in the Cretaceous period from about 65 to 135 million years ago. Most of the commercial deposits are of Pliocene through recent age, and are younger than 35 million years. Diatoms are still abundant in present day lakes and seas. The living diatom is supported and protected by two half cell walls or valves united by a connecting band or girdle. These valves are composed of opaline silica extracted from the water in which the diatom lives. After death of the diatom, the silicious remains settle in the lake or sea and accumulate at variable rates approaching several millimeters per year for very active diatom colonies. This accumulation of silicious sediments, after decay of the organism, burial, and uplift, can result in the formation of diatomaceous earth deposits.

Jan 1, 1987