Search Documents

By Peter G. Kovalchik

To compare the viability of the new fuse wire arc test (FWAT) as a substitute for the comparative tracking index (CTI) for determining surface resistance to electrical tracking, the Bureau of Mines constructed a fuse wire arc tester and undertook a detailed testing program for testing insulating materials used on explosion-proof enclosures. This report describes the Bureau's apparatus, the two methods (CTI and FWAT), and the results of the Bureau's testing, showing comparisons of the FWAT with the CTI. Results showed strong correlation between the two methods, as all specimens tested that had CTI ratings of 400 V ac rms and above passed the 10-test sequence with the FWAT, whereas all specimens with lower CTI ratings failed, with the number of tests to failure corresponding roughly to the descending CTI rating order.

Jan 1, 1987

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By Thomas Mütze, Anja Hirte, Ursx Peuker, Thomas Kuhn

"The comminution behavior of two ferromanganese nodules samples of the equatorial northeast Pacific has been examined as a basis for the separation of two kinds of metal-rich layers. Those layers were finely grown together during nodule formation and are one reason that the exploration of deep-sea minerals calls for the development of new mineral processing concepts. Therefore fundamental analyses of the fracture behavior have been made under compressive and impact stress. Further experiments took focus on the crushing behavior in a jaw crusher and a small scale impact crusher as well as the milling behavior in a dry vibrating mill, a wet planetary ball mill, and a wet agitated ball mill. The comminuted products were characterized by PSD, particle shape, particle density, and porosity. The experiments show a low stress resistance of the ferromanganese nodules. Compared to compressive stress, impact stress turned out to be the more effective for crushing. Both samples showed no significant difference in the comminution behaviour which makes differing mechanical treatments unnecessary. In both cases particle sizes below 1 µm were achieved by wet grinding. This particle size is necessary to separate the two kinds of metal-rich layers which is part of continuative studies."

Jan 1, 2014

By Mark J. Zdunczyk

"Frac sand is industrial silica sand much like glass, foundry, filtration and blast sand. The sand must meet certain specifications set forth by the industry that consumes the product. The production and consumption of frac sand has experienced record growth in the last 10 years because of new oil and gas drilling, new horizontal well drilling, multi-stage fracturing and the stimulation of older wells that have little or no production. Frac sand is needed to “prop open” the fractures in the rock reservoirs to allow oil and gas to flow out more freely.According to the U.S. Geological Survey (USGS), the estimated production of frac sand in 2015 was 71 percent of the total production of industrial silica sand or 67.4 Mt (74.3 million st). This is a decrease of about 12 percent from 2014. However, the silica sand industry and other industry sources estimate only 50 Mt (55 million st) of frac sand were produced in 2015. In recent years both the USGS and industry studies have been very close in estimating the production of frac sand but with the recent downturn in frac sand production, perhaps, reporting to the USGS was not as accurate. These discrepancies may be that the USGS statistics are based on voluntary reporting by the industry and some companies report their approximate production, others may not. It is always difficult to obtain accurate production figures of any industrial mineral or construction aggregate operation as most companies tend to keep those figures somewhat confidential. It is certainly accurate to report that the production of frac sand had decreased since the last quarter of 2014 and through 2015. The oversupply of oil and natural gas has led to this decline in frac sand usage. Oversupply has idled drilling rigs and well completion activities. World Oil Magazine reports that 2015 was the worst year for rigs in a quarter century. The only wells being completed are those that have contract agreements to do so, others have been capped. Very few new wells are being drilled. Since about 98 percent of well completion is sand and water, the sand supply has caught up with the demand. There are some bright spots in the “oil patch” as the Permian Basin in Texas and the Woodford Shale in Oklahoma have kept pace somewhat with drilling and completion. It has been reported that the frac sand producers in the Brady-Voca, TX area are producing to nearly capacity. The northern frac sand producers like those in Wisconsin, Illinois and Minnesota are feeling the downturn because of the cost of shipping sand to these moderately active basins and plays. The “rule of thumb” is that freight is 2/3 and sand is 1/3 the cost."

Jul 1, 2016

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By L. Katgerman, H. J. Brinkman, J. Duszczyk

"The phase formation sequence in the in-situ synthesis ofTiB2 in A1 from elemental A1, Ti and B powders is identified with a combination of DSC and XRD. After the melting of A1, A1B2 and A13 Ti are formed at the contact areas between A1-B and A1-Ti. The influence of variations in starting composition on the reaction kinetics is explained in terms of there effect on the different processes in the formation sequence. Parameters in the starting composition that were investigated are; fraction ofTiB2 forming reactants, non stoichiometric Ti:2B ratio's, and addition of alloying element Cu.It was found that a liquid Al phase is necessary for the in-situ TiB2 forming reaction from the intermediate A1B2 and A13 Ti phases. If all Al is consumed by the formation of A1B2 and A13 Ti the TiB2 formation is halted until the decomposition of A1B2 and A13 Ti .Overstoichiometric amounts of B are needed for complete conversion of the Ti, present in A13Ti, into TiB2 This is explained by the fact that some of the stable A1B12 phase is formed after the decomposition of A1B2•The addition of Cu leads to an increasing reaction rate in the A1-Ti reaction. A possible explanation for this is that the A1-Cu liquid penetrates more easily between the Ti and its surface oxide than the unalloyed A1 liquid."

Jan 1, 1998

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By Kenneth E. Merklin

The heavy media process is now being used extensively throughout the world for the gravity concentration of a great number of different minerals. The process is a commercial adaptation of the heavy liquid procedure which has been used in laboratories for many years to separate mineral of different specific gravities. In the heavy media process, a suspension of finely divided particles in water is used to increase the apparent specific weight of the fluid to the desired separating point. The original heavy media process used sand, galena, pyrite and occasionally other materials as the solid constituent of the separating suspensions. As the process developed, the need for a more universal media meeting the following requirements was recognized: 1. High specific gravity. 2. Resistance to abrasion. 3. Resistance to corrosion, 4. Readily reduced to a suitable size consist for suspension in water. 5. Available in quantity at economical price levels. 6. Easy to recover by a simple method.

Jan 1, 1958

By F. Sill

The disposal of residual material from processing and combustion of coal, from incineration of domestic refuse and sewage sludges kind to the environment is a prior task for the future. Deutsche Montan Technologie (DMT) has developed a new technique which makes possible to fill-up goaf cavities behind running caving systems in coalmining. In a mixing and pumping station on the surface high concentrated suspensions are produced from the above mentioned materials. The paste is pumped through pipes to the coalfaces and via trailing discharge pipes stretched to the fracture zone in the caved-in goaf. Since three years a special designed plant is working successfully on a coal mine of Ruhrkohie AG.

Jan 1, 1994

By S Bouzalakos, W Timms, H Malli

Combining ultramafic mine tailings and acidic mine drainage via mineral carbonation to sequester carbon dioxide, presents an opportunity to minimise waste on mine sites. Low pH mine water with trace element concentrations can be effectively treated by high magnesium mine tailings, a useful source of finely ground reactive matrix. By using milled tailings for mineral carbonation, there are negligible energy requirements for communition of ore rocks to reduce particle size. This study aimed to assess the technical applicability of reacting ultramafic tailings and acidic mine water through mineral carbonation technology in the mining industry. Dissolution has been identified as the rate limiting stage in mineral carbonation; hence the study focused on identifying optimal dissolution conditions. Ultramafic tailings (particle size <100 µm) derived from serpentinite ore, were reacted with a typical mine water that was synthesised in the laboratory. Through variances in the solid to liquid ratios and temperature of dissolution, a maximum five per cent magnesium dissolution efficiency was reached at 50 g/L and 100°C. The acidic mine water was neutralised (from pH <2 to pH ~6) and iron, copper and zinc ion concentrations reduced significantly during the formation of solid precipitates. Carbonation was undertaken by injecting carbon dioxide into the magnesium-rich solution to form stable carbonates. The experimental work demonstrated proof of concept; however, dissolution efficiency and carbon dioxide sequestration was low, indicating that further research would be required before larger scale implementation.CITATION:Malli, H, Bouzalakos, S and Timms, W, 2015. Ultramafic mine tailings to treat acidic mine water and lock away carbon through mineral carbonation, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 133–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M. Kalicinski, M. Lyssyy

"Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such real-time information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing case studies of their use in African and Australian iron ore and European steel, as well as a description of the potential benefits of a range of analysis equipment.INTRODUCTION Access to information is critical for any process, and is a fundamental component for making process control decisions. In order to yield effective processing outcomes, it is important for that information to be readily available, preferably as quickly as possible, and to be as accurate as possible. While speed and accuracy are often traded off against each other, there are numerous technologies available in a processing environment that allow for both rapid flow of information and a high level of accuracy. The use of on-belt analysis equipment has a long trusted history of use in a number of mining and processing environments and industries, providing information such as elemental composition and grade of conveyed materials, moisture content, waste proportion and energy information. Australian company Scantech has been a provider of such equipment since 1981, and has become an industry leader in both the supply and development of on-belt analysers across a range of industries."

Jan 1, 2018

By Y. C. Avniel, T. E. Warner

"It is important to be able to measure sulphur and nitrogen in molten iron and steel on-line. Unfortunately, there are no solid electrolytes which are stable under oxidising conditions and in which the ions of these species are mobile. In this paper, novel applications of beta alumina electrolytes are described and the results compared with data in the literature. Excellent agreement was obtained confirming this approach as a viable method of detecting elements whose ions are not mobile in solid electrolytes.IntroductionIn the past two decades, the rate of many processes in steelmaking have increased substantially. The sophistication of chemical analysis has also increased but analytical equipment is frequently positioned a significant distance from the operating plant which dictates that time is spent taking a sample, sending it to the analytical facility, preparation of the analytical sample prior to insertion into the equipment. In many cases, the time taken for analysis can exceed the time taken for the actual process and is now the rate defining step. Furthermore, most analytical methods are unable to distinguish between the amount of element which is dissolved in the steel and that contained in precipitates. Even if the analytical equipment could separate these two, the distribution would have changed between the molten steel and the cast sample. It would be an advantage to analyse on-line for impurities in molten metals."

Jan 1, 1997

By R. D. Irvine

Enhanced concern for protection of the environment and attendant actions by environmental regulatory authorities in support of this concern are influencing to varying degrees the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms. In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States.

Jan 1, 1995

By Christoph Muller, Geoffrey Liggins, Mohan Hensman

Modern commercial blasting is as much a technical process as it is a business one. As with most processes both aspects of blasting are driven by and generate new data. The time-critical nature of commercial blasting in mining and construction projects, dictate the timely exchange of information so as not to impede production or commerce. Up-to-date information about the blast to be undertaken can help suppliers: meet customers’ expectations to address challenging ground conditions; react to a market where quickly changing orders occur regularly; and address as-drilled blast patterns as opposed to baseline plans. “Real-time” data exchange into and out of the blasting process supports the whole-of-mine data management that the industry is migrating to.

Jan 1, 2010

By Wing Ka Ng

Substitution of pulverized coal injection by solid biocarbon fuel has the potential to achieve substantial reduction in GHG emissions associated with blast furnace ironmaking. A systematic evaluation was conducted on the performance of solid bio-carbons produced from a single raw biomass source using different pyrolysis technologies. The potential of solid biocarbon in reducing GHG emission of the blast furnace ironmaking process is strongly influenced by its O/C mass ratio. In order to achieve substantial GHG reduction, it is necessary to replace coal injection by solid biocarbon having a low O/C mass ratio. The pyrolysis technology and conditions employed are key parameters influencing O/C mass ratio of the resultant solid biocarbon. Close collaboration between steelmakers and solid biocarbon producers is critical for producing suitable solid biocarbon fuel to replace pulverized coal injection. A successful partnership should pave the way in achieving substantial reduction in GHG emissions of the blast furnace ironmaking process.

By George L. Gates

The Bureau of Mines developed a rapid instrumental method of analyzing oil well scales containing primarily barium sulfate. After removal of oil and water by carbon disulfide) the scale was dissolved in strong hydrochloric acid. The cations, barium, calcium, strontium, magnesium, and iron, were determined with the flame photometer using the method of additions. Sulfate was deter-mined colorimetrically after separation by selective adsorption on an alumina column. Phosphate was determined colorimetrically and carbonate titrimetrically. The method was reasonably accurate, although iron and magnesium were found to have mutual interference.

Jan 1, 1965

By M. Ruonala

The Larox Power PF Pressure Filter has been developed to meet the challenges of ever increasing output tonnages demanded by the minerals processing industry. This paper will highlight recent experiences at the Rudna Copper Concentrator in Poland, the Escondida Copper Concentrator in Chile and some large zinc concentrators in Australia. Detailed maintenance and operating cost information will be disclosed. Emphasis will be placed on economics on scale gained from higher machine throughputs.

Jan 1, 1998

By Chidchai Loyprasert, R. A. Stoehr

"A computer model has been developed to predict grain structures in alloys solidified under unidirectional flow using a combination of three techniques -- solution of the equations for flow of an incompressible fluid bounded by curved surfaces by the SOLA-SURF algorithm, calculation of heat flow by a finite difference method, and simulation of grain formation by a two-dimensional cellular automaton (CA) model. The changing rigid surface has been taken into account. Heterogeneous and homogeneous nucleation are considered, and the growth kinetics of a dendrite tip are evaluated by the Kurz-Giovanola-Trivedi (KGT) model. These calculations were applied to solidification of an Al-4.5% Cu alloy flowing over a chill on the bottom of a channel, a system for which experimental results were available. Using a variety of flow rates and superheats, agreement between the computed and experimental results were very good including transitions between columnar and equiaxed grains, the aspect ratio of the grains, and the inclination of the grains to the flow.IntroductionModeling of casting and solidification processes has developed over the years along two distinct tracks: (1.) modeling of macroscopic heat transfer and fluid flow for design purposes, and (2.) modeling of microscopic processes such as nucleation and growth in order to improve the scientific understanding of the phenomena involved. The present work is an attempt to combine the macroscopic and microscopic approaches for the solidification of an alloy flowing over a chill. The specific case chosen is that of an aluminum-4.5 % copper alloy flowing linearly over a water-cooled copper chill for which experimental results were available over a range of flow rates and superheats. For the macroscopic calculations, the SOLA-SURF algorithm for solution of the twodimensional fluid flow equations was combined with the finite difference method (FDM) for calculating heat transfer. For the microscopic calculations, heterogeneous and homogeneous nucleation were considered, and the growth kinetics at the dendrite tips were evaluated. The cellular automaton (CA) technique was used to apply the microscopic kinetics to the temperature and .flow conditions."

Jan 1, 1999

By James P. Odendahl

Missouri is a state rich in mineral commodities. There is a variety of types of mining as well as minerals in the state. Different phases of mining are controlled by a variety of state and federal laws. What I hope to do today is to present briefly some of the interaction and interplay that has occurred in the recent years between the mineral industry and the Missouri regulatory agencies, as well as some of the interactions by federal agencies. First a little history which dates back to the late 1600's. For many years Missouri has been a leader in the production of lead and zinc. In fact, recent studies have indicated that Missouri produces better than three-fourths of the nation's present lead supply. Less well known but important resource is iron mining. Some of these operations were the source of confrontation during the Civil War. Major battles were fought in and around Ironton, Missouri where iron mining has occurred for many years. One of the largest pelletizing operations in the state is currently located within the city of Ironton. Joplin, Missouri, the home of Thomas Hart Benton, the famous Missouri painter, has a history of lead and zinc mining, going back to the later 1800's. Many of the paintings by Benton contain reference to the early days of mining in Missouri. There is a Benton mural in the City Hall at Carthage depicting the early days of lead mining in that area. Later, the center of lead mining moved to southeast Missouri near Bonne Terre and Flat River. The names of the towns in this area reflect the history of mining, examples - Leadington, Old Mines, Rivermines, etc. The history of lead mining in Missouri has been referred to in some detail in various publications(l).

Jan 1, 1977