Search Documents

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below II mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-SiO2 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, .the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe3O4 on the viscosity was quite significant. The viscosity of slag increased by 300mPa-s at 1573K when Fe3O4 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 systems is given in this study.

Jan 1, 2003

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

By Dong Liang, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"The formation, distribution and survival of pure Al nuclei under surface pulsed magneto oscillation (SPMO) treatment were investigated with thecombination of experiments and numerical simulation. The results indicated that the nuclei originated from the whole top surface of melt owing to the oscillation of top surface induced by SPMO. The temperature field significantly affected the survival of the nuclei The electromagnetic force and flow field of the melt with SPMO treatment were simulated by finite element software ANSYS. The electromagnetic force mainly distributed below the top surface near the mould wall. The electromagnetic farce not only made the melt oscillate but also increased the convection of meh below the top surface vigorously. The oscillation near the top surface of the melt promoted the nucleation largely, and the convection increased the uniform of the temperature distribution in the whole meh which favored the survival of nucleiIntroductionAs we all know, fine equiaxed grains are beneficial fur the improvement of the mechanical property, process ability and the uniformity of metallic materials [1-2]. With the researches of recent decades, people discovered that the electromagnetic field is an efficient method to refine the solidified structure of metals [3-7]. Pulsed magnetic field technology obtains more and more attentions in recent years due to its smaller power consumption, bigger instantaneous magnetic field intensity, non-contacting with the meh and simple convenient equipment manufacturing [8-9]. However, the melts would splash fiercely when pulsed magnetic field is applied with a slightly higher power. Thus, based on the understanding of the solidification refinement mechanism of electric current pulse (ECP) [10], Gong et al [11] developed a novel technology called pulse magneto-oscillation (PMO) to refine the solidification structure. The technology can be easily applied in the solidification structure refinement of continuous casting slab. But fur aluminum continuous casting, the sump is very shallow, which greatly limits the application of pulse magneto-oscillation technology."

Jan 1, 2014

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Winfried Rosenstock

AEBT has been available for a couple of years and is successfully applied in Australia. Up to now it was mainly used in coal surface mining at the Australian East- Coast. Presently, the proved results reach ~ 50 % reduction of Drilling & Blasting costs and a productivity increase of between 10 and 20 %. In 2003 it was for the first time used in surface metal-mining. The mine features for the time being an extremely difficult geological environment and had above to be carried out in the transition level waste/ore. Reductions of wall control, powder factor and vibrations were the main target.

Jan 1, 2004

By Robert E. Loftus

"The author discusses the growth in the use of ocean-going bulk carriers for the transportation of mineral commodities, and predicts future trends. The various types of tonnage carriers are described, along with the special discharging gear used, the costs involved and the duties of some of the personnel.THE FIRST CONSIDERATION in planning the ocean transportation of minerals is the type of vessel to be utilized. The modern 'Bulk Carrier' bas proved to be the most successful vehicle for the purpose. I would there-fore like to describe this fleet in some detail and at-tempt to show the impact that the bulk carrier bas bad on the movement of bulk materials."

Jan 1, 1968

By Z. Q. Zhang

The iron ore from Yichang in China assaying 41.64% Fe and 1.02% P is a low grade and high phosphorus oolitic hematite ore. The separation of iron minerals from gangue minerals in the ore by conventional processing techniques is ineffective owing to their close similar properties. The modification of iron minerals by microwave-assisted reduction was investigated in order to improve separability of the ore. The effects of microwave-assisted reduction on the subsequent low intensity magnetic separation and floatation were examined. The results show that the main factors affecting the reduction and separation process are grinding size, reduction temperature and reductant. Fine grinding of the microwave-treated ore to smaller than 0.074mm was found to be imperative due to the tiny dissemination characteristics of iron oxide minerals. After magnetizing reduction by microwave heating at 500?, the magnetic concentrate containing 58.36% Fe and 0.67% P can be obtained with the Fe recovery of 91.28%. Magnetizing reduction drops the floatability of iron oxide minerals, thus reverse flotation is fit for upgrading the magnetic concentrate to contain 62.13% Fe and 0.21% P with Fe recovery of 81.59%. Compared with present microwave-assisted reduction technique of carbon reductant, using a waste iron powder as reductant is a novel and effective technique without the green house effect caused by the release of CO and CO2. Waste iron powder with a faster response to microwave heating then coke and charcoal can be recovered by magnetic separation in a low cost and plays the role of reductant and microwave heating accelerator.

Jan 1, 2014

By Industrial Research Office

"The U.S. Bureau of Mines established on August 15, 1983, the Generic Mineral Technology Center for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. The Center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . ."" The Center's program is designed to permit an accelerated attack on the fundamental research problems for the control of respirable dust in mines.The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. The Generic Technology Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated. The Center activities involve the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications' in the respirable dust area.The Center is composed of faculty from the four universities/institutes listed above. The personnel, facilities and equipment that are available to the Center from these entities are diverse, complementary and comprehensive. More than fifty scientists, engineers; and medical personnel in the Center are engaged in respirable dust research. Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease Studies are available as a result of the existing relationship between NIOSH and West Virginia University.The breakdown of the dust research program into the five areas mentioned above recognizes the importance of an integrated fundamental research approach to the respirable dust problem compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities. The specific projects in the research areas are a result of a careful evaluation of the past and ongoing research activities, the identification of areas where data and information are scarce, and awareness of the recommendation of the National Academy of Sciences Study on the Measurement and Control of Respirable Dust. Penn State is the administrative unit for the Center. Funding to date is nearly $6.5 million."

Aug 31, 1989

By E. G. King

Sodium-aluminum and calcium-aluminum silicates are important rock-forming minerals. While many of them are of only theoretical interest, several are of practical importance--as ceramic raw materials and as potential future sources of aluminum. Heretofore, thermodynamic data for these minerals were incomplete; and in many instances missing data were difficult to estimate reliably. This has seriously hampered thermodynamic calculations pertaining both to the natural formations of these minerals and to their decomposition in sintering and fluxing reactions. This paper reports the results of the Federal Bureau of Mines measurements of low-temperature heat capacities of four crystalline silicate minerals--dehydrated analcite (NaAlSi2O6), hexagonal anorthite (CaA12 Si208), lawsonite (Ca2Al2Si2080?2H20), and leonhardite (Ca2Al4Si8C24?7H2O). It augments previous similar measurements of related minerals, which were summarized recently.4 The measured heat-capacity data were used to derive entropy values for the four minerals at 298.15° K. Some relations between these entropy values and those of other similar minerals were discussed. These relations illustrate the difficulty of estimating entropy values of tertiary (or higher) silicates.

Jan 1, 1961

By Robert E. Moore

Synthetic spinel is proving to be a highly effective refractory for specific applications, but its cost limits applications. Formation of spinel from a raw material such as diaspore or bauxite could provide a suitable and less costly starting material. In the study reported here, finely ground (-325 mesh) diaspore from Missouri and bauxite from Guyana and China are combined with hardburned MgO (-325 mesh) in appropriate proportions to yield spinel and spinel with secondary phases. A classical sintering and creep study was completed, accompanied by a microstructure study to determine completeness of the reactions and morphologies of the reaction products.

Jan 1, 1991

By B. Hester

Many Third World countries of Third World Africa are well-endowed with minerals, especially gold. Political and economic conditions discouraged interest by Western capital for the several decades since colonial rule. Influence from Eastern Block countries has gone and the left wing orientation widely favored by Third World countries has almost disappeared. Under International Monetary Fund influence, these countries now solicit Western finance to expand their industries. Mining is especially encouraged. The paper describes the financing of some recent developments and examines trends and opportunities in some of the more attractive countries.

Jan 1, 1993

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-Si02 and FenO-MgO-CaO-Si02 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below 11 mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-Si02 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe304 on the viscosity was quite significant. The viscosity of slag increased by 300mPa's at l573K when Fe304 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-Si02 and FenO-MgO-CaO-Si02 systems is given in this study.

Jan 1, 2003

By Z. Sun

The hydrogen embrittlement and stress-corrosion cracking (SCC) behavior of an a -titanium alloy and its two kinds of welding samples have been investigated. The results show that this alloy has very low susceptibility to SCC, and the values of Kiscc for the alloy are 46.4 MPa ? m' 65.86 MPa ? mu2 in the direction of T-L and L-T, respectively. The scanning electron fractographs show transgranular and quasi-cleavage fracture. The hydrogen embrittlement results show that the notch sample of the alloy is not sensitive to hydrogen, but the electro-beam welding and diving-arc welding samples are sensitive.

Jan 1, 2005

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Nowadays recycling became an important rare earth elements (REE) source, which allows to reduce their demand for extraction from natural deposits. At present, the used fluorescent lamps and old type TV or computer monitors kinescopes are selectively collected and undergo processing in the system of recycling. It has been estimated, that utilization of such waste would be sufficient to cover the REE demand for the next 5-8 years. In the developed process, the luminophores were separated from the electronic and electronic waste materials, and processed by hydrometallurgical methods to obtain concentrated REE in form of oxides. INTRODUCTIONInternational Union of Pure and Applied Chemistry (IUPAC) defines the rare earths as a set of seventeen chemical elements, specifically the fifteen lanthanides plus scandium and yttrium. They are considered the most important indicators of the developed technologies and techniques. Rare earths are used, amongst others, for the production of magnetic and superconducting materials, ceramics, lighting, catalytic converters, advanced electronics and alloys. The demand for RE continually increases, similarly to many other primary raw materials. Globalization, the growing demand for limited resources of raw materials, the policy of the countries controlling the raw material market and the economic crisis became a spur for new programs of socio-economic development of the European Union (EU), with particular regard to EU safety for commodities in intermediary as well as long-term horizons (COM 2008), COM 2011).EU countries import most of metallic and chemical raw materials important for their economy. In 2008 a detailed program named Raw Material Initiative was announced. The increase in demand for most raw materials having special importance for the development of technology, and access to of raw materials security of supply affect the future economies of the UE member states and other developed countries."

Jan 1, 2012

By D. R. Jolley

"The selection of equipment for open-pit mining is an important decision which results in a considerable capital expenditure by the operator. The decision is complicated by the wide product range on the market. Certainly, equipment performance is an important criterion to consider in making the decision. Equally important, however, is the operating inter-relationship among the equipment. A poor balance increases production costs and waiting time as queues form at the bottlenecks. This inter-relationship is dependent on equipment performance, but it is also affected by management decisions (i.e. scheduling techniques).The purpose of this paper is to show how the computer is used to decide which equipment and operating decisions achieve the required production objectives at least cost. Actual mining of the pit is simulated over a period of time using different equipment and scheduling decisions. Production, waiting time and costs are evaluated for each alternative until the operator is satisfied that he has achieved the best result."

Jan 1, 1970

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By W. J. Bronkala

Dense-medium circuits have been installed in many mineral treatment plants since its, original development about thirty years ago. In the intervening, period the process has been thoroughly evaluated and many innovations have been introduced. The Heavy Density. Cyclone is one of the newer systems which has extended the operating range of this process to 65 mesh size. Several different finely divided materials have been used to produce the separating bath but nearly all new plants use a ferro-magnetic medium. The, advantages of magnetic medium include: 1. Smaller recovery plant 2. Lower cost recovery plant both in initial and operating cost 3. Excellent medium stability 4. Dependable medium supply at reasonable and stable cost. Magnetic separators are used to recover this magnetic medium and the smaller plants and lower operating costs are directly related to their use.

Jan 1, 1964

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003