Search Documents

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. Based on thermodynamic analysis, the present work discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extraction and low acid consumption. Rare earth extractions as high as 80 percent were achieved, while iron and thorium extractions were lower than 1 percent, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature.

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By Keith MacKay, John Carter, David Siddle, Fernando Faminia

"The River Green Residential development, is located in the municipality of Richmond, BC adjacent to the Fraser River. Ground conditions at the site consisted of medium to fine grained alluvial sands and a high groundwater elevation. A temporary low permeability retaining wall was required in order to facilitate the construction of an underground parking structure without inducing settlement of adjacent structures, which include the Richmond Olympic Oval; part of the legacy of the Vancouver 2010 Winter Olympics. Golder Associates Ltd. and GeoPacific Consultants Ltd. utilized Cutter Soil Mixing (CSM) technology to enable construction of a continuous combined low permeability cut-off and retaining wall around the perimeter of the property. The 350m long wall was keyed into marine clay at a depth of 28m below ground surface, and contained H-Pile reinforcement installed at regular intervals. The CSM technology provided many benefits for this project, allowing the combined cut-off and retaining wall to be constructed within a very narrow footprint (650mm width). The low noise impact and near vibration free construction of the CSM equipment provided minimal inconvenience to nearby stakeholders during construction. To reduce dewatering volumes during excavation and prevent significant water-table drawdown the Hydraulic Conductivity requirements for the wall were 1 x 10-7 cm/s or less. Project specifications called for a different strength requirement for upper and lower portions of the wall. The top 13 meters of the wall required an Unconfined Compressive Strength (UCS) of 4MPa to act as a retaining and cut-off wall, whereas the bottom 15 meters of the wall required a UCS of only 0.5 MPa to act only as a cut-off wall. Wet-grab and core samples were obtained from the panels to confirm the UCS and Hydraulic Conductivity specifications were met.INTRODUCTIONGolder Construction Inc. and GeoPacific Consultants Ltd. conducted the design and construction of a deep soil mixed cut-off and retaining wall system. The “dry-box” solution was used to surround the excavation of an underground parkade and prevent flows of groundwater into the excavation."

Jan 1, 2016

By David Chadwick, Paul Marsden, Chris Hughes, Mathias Delapille

"Following damage caused by the 2011 Christchurch earthquakes, the NZ$127.5million Christchurch Town Hall Restoration project is due for completion in 2018. The building is undergoing extensive repairs and a strengthening regime to meet New Zealand’s New Building Standard. One major aspect of the project is the stabilisation of the soil directly beneath the building using interconnected jetgrouting columns installed a cellular configuration, the purpose of this being to decrease the likelihood and severity of foundation movements caused by earthquake-induced soil liquefaction and lateral spreading. The soils encountered on the site ranged from cobbles and gravels through to sandy silts with a significant quantity of timber and rootlets. This wide variation of soil types presented a number of challenges with regard to effective and consistent treatment by jet grouting. The paper presents an overview of the quality assurance practices and also the testing regime adopted on this project.INTRODUCTIONMost of the deformation experienced by the Christchurch Town Hall structure over the course of the Canterbury earthquakes was caused by movement of the underlying ground. Two primary mechanisms of ground deformation were observed:- Liquefaction of the soils underlying the building foundation- Lateral spread of surface soils towards the free face at the river edge which runs 20 metres from the building. This mechanism also resulted in additional vertical settlement of the building foundations.The overall foundation design philosophy adopted by the project team for the Christchurch Town Hall Conservation Project has been to improve the ground directly beneath the structure to mitigate against these two mechanisms of ground movement. Additionally, a robust raft slab is proposed to distribute the foundation loading more evenly and increase the ability of the structure to resist lateral stretch of the underlying ground.The ground improvement system proposed by the Client’s geotechnical consultants, Tonkin &Taylor, comprised a cellular arrangement of interlocking jet grout columns, this arrangement would effectively encapsulate the soil within the cells preventing lateral spread.In total 1,097 interlocking jet grout columns, extending over the entire floor plan of the structure, were required to satisfy the design requirements."

Jan 1, 1900

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By Robert Essler, Paul Marsden, Paul Pandrea

"1. THE VICTORIA STATION TRANSPORT HUB Victoria Underground station is part of the Victoria transport hub, which comprises one of London’s main train termini and a major bus station. At the Underground station, the District Line running in the older shallow brick tunnels dating back to 1868 cross the Victoria Line running in the lower tunnels, which were opened in 1969. After Waterloo, Oxford Circus and King’s Cross/St. Pancras Tube stations, Victoria is the most frequented station on the London Underground network and is used by over 80 million passengers per year. Capacity at Victoria Tube station has been inadequate for many years with passenger numbers steadily rising. Overcrowding is a constant challenge and the station has to be closed regularly during morning and evening peaks until sufficient trains pass through to clear the platforms. For this reason an extension has been debated since the 1990s. After intensive preliminary investigations and feasibility studies covering many variants, which included a large-scale jet grouting test to determine the applicability of this technology as a protective measure for the tunnelling works, the project was officially started with the Victoria Station Transport and Works Act Order (Secretary of State, 2009) effective on the 18th of September 2009. Following a competitive tender process a joint venture of Taylor Woodrow and BAM Nuttall were awarded the contract by London Underground, with their design being carried out by Mott MacDonald Ltd. Ensuring the busy station remained open to the public was a key requirement of the Victoria Station Upgrade. Jet grouting works, which were executed from ground surface, were also carried out while the station was fully operational 2. OVERVIEW The Victoria Station Upgrade aims to increase the capacity of the Underground station significantly and one of its major design objectives is to optimise the transfer between the Underground lines. In order to achieve this, the following new structures are currently under construction: •,A new North Ticket Hall •,Extension of the existing South Ticket Hall •,Nine new escalators •,Connecting tunnels between the North and the South Ticket Hall •,8 new lifts providing step free access to all platforms •,An improved connection between the rail/bus terminus and the Underground station As the elevation and geometry of the existing structures cannot be changed, the new structures need to be adapted to the existing structures (see Figure 1)."

Jan 1, 2016

By FJ. Johnson

Polymer utilization has increased steadily over the past several decades; however, their usefulness is sometimes limited by natural forces. For example, polymers tend to degrade when subjected to elevated temperatures. This degradation can release toxic fumes, create excess smoke, and aid in the spread of fire. For these reasons, many polymers are filled with various compounds which impart flame retardancy (FR) properties. These fillers do not make polymers non-combustible; rather, they increase resistance to ignition and reduce bum rate. Also, they suppress smoke generation, which is important as up to 80% of fire-related deaths are due to smoke inhalation [1]. Therefore, methods to impart flame retardancy in polymers are industrially important. The early flame retardants used in polymers were halogen-based, working on the principle of inhibiting free radical formation in the vapour phase thus impeding combustion propagation [2]. Usually these were combined with antimony compounds such as Sb203 to decrease loading, yet provide the same FR qualities. However, questions have arisen recently concerning toxicity of halogenated flame retardants. Possible release of toxic compounds (such as dioxins) upon combustion has been reported [3]. Fear of future regulations concerning halogen addition has led to the search for different FR fillers. Two of the more common replacements for halogen-based systems are alumina trihydrate (Al(OH)3 or ATH), and magnesium hydroxide (Mg(OH)2)' These systems impart flame retardancy through heat absorption and by release of water of hydration upon their decomposition. ATH has a low decomposition temperature (230°C), limiting its use to unsaturated polymers, epoxies, urethanes, and some wire and cable formulations. However, some advantages of ATH over halogenated FR are that it is relatively cheap, doesn't generate toxic gases, is non-volatile, and is impervious to moisture [2].

Jan 1, 1997

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By F. Montgomery Lyon

Pyritic sulfur in coal occurs as discrete mineral particles, and its liberation and physical rejection is the primary target for coal desulfurization. An acceptable solution to the pyrite removal problem from fine coal is not found in the standard methods of coal cleaning such as jigging, heavy-medium separation, tabling, and hydro-cycloning. Although fine coal is an ideal size for froth flotation, this method, as currently practiced is also unsuitable as the fine pyrite usually floats with the coal. One possible solution to this problem may be the froth flotation of pyrite from coal. This reverse flotation scheme would have the major advantage of removing both free pyrite and locked pyrite-coal combinations. With this possibility in mind, we have, as a first step, compared the flotation and adsorption. characteristics of an ore-pyrite and coal-pyrite with potassium-ethyl-xanthate as a collector 1 Related Research. The action of ethyl-xanthate on coal has been studied 2 by Horsley. He measured the contact angles of coal in distilled water and in the presence of purified ethyl-xanthate. The results indicated that the xanthate was not adsorbed by the coal. Additional contact angle data were obtained to determine the effects of cupric, ferric, and ferrous salts on the system. Then either the ferric or cupric salts were in, solution with the xanthate, there was an increase in the natural contact angles of the coal. This indicated that these heavy metal ions activated the flotation of the coal with xanthate. However, ferrous iron did not act as an activator. Horsley stated that the most attractive explanation was that the xanthate is oxidized to dixanthogen in the presence of the ferric and cupric ions.

Jan 1, 1971

By J. -M. Milazzo, T. Wallmach, S. B. Blancher, A. Amalric

In a FeNi electric arc furnace, the physical properties of the slag (chemistry, viscosity, liquid/solid/gas ratio) are of crucial importance in controlling the efficiency of the process. In this paper, we studied the slag crystallised on the walls of a semi-industrial furnace (freeze-lining), the slag rising through the burden during foaming phenomena, and the casted slag. The freeze-lining is the layer of oxides that crystallises on the refractory wall of a furnace, protecting it from chemical and mechanical aggression. It records changes in furnace conditions (slag chemistry, temperature, oxygen fugacity), which makes it possible to observe the impact of these elements. In the high reduction test, the freezing lining is composed of magnesian olivine. Switching to a low reduction process increases the Fe content of the olivine and causes orthopyroxene to appear, making the freeze-lining mechanically and thermally weak. Thermal incidents in the furnace cause significant slag foaming. This foaming is produced by a massive crystallisation of the olivine (due to the drop in temperature), and inducing an exponential increase in viscosity, preventing the free circulation of gases. These foaming episodes are also recorded in the freeze lining and form layers rich in gas bubbles, and therefore mechanically fragile. The slag casted and cooled in a ladle allows the first steps of slag crystallisation to be studied. Olivine is the liquidus phase, with a magnesium-rich core and an iron-enriched rim, contemporaneous with the orthopyroxene phase. The habitus of these phases is very similar to that found in komatiites for the same minerals. FeNi slag is therefore an industrial analogue that is easy to study and compare to komatiites. Keywords: Pyrometallurgy, ferronickel, slag, freeze-lining, characterisation, olivine, mineralogy

Jan 1, 2020

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By Harry L. Brown, Philip E. Armstrong

Young's modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young's modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young's modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young's modulus was calculated by the formula: E = 4f2f2p where E = Young's modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young's modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young's modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson's ratio. The results are usually meaningless and sometimes absurd.' RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By Luís Marcelo Tavares, Daniel Francioli, Malcolm Powell, Mohsen Yahyaei

"Mathematical modeling of the comminution process requires understanding of all breakage mechanisms occurring in this mechanical environment. Modeling of high energy impact breakage is well established, however, modeling low energy breakage including incremental damage breakage, attrition and abrasion is still under development. Free fall incremental impact tests were carried out to investigate the surface fragmentation of a copper-gold ore. This process was achieved by dropping particles individually from a height of four meters onto a metallic plate. The impact specific energy was 0.01KWh/t. The setting of the metallic plate was changed to test the impact angles of 0°, 45°, and 60°. Tests were carried out using fresh angular rocks as well as smoothed particles. Changes to the plate angle and particle shape enabled the study of the influence of the tangential component of the impact energy along with particle shape on superficial breakage. By studying the fractional mass loss variation in each impact, two distinct stages of surface fragmentation were clearly determined: high fractional mass loss dominated in the first 10 impacts and was attributed to chipping, whereas low fractional mass loss occurred for the remainder of the impacts and was attributed to abrasion. Smoothed particles demonstrated higher resistantance to breakage and their surface fragmentation behavior indicated a closer relationship to abrasion, especially when lower impact angles were used."

Jan 1, 2014

By Shin-Kun Ryi

The world nowadays faces many challenges associated with excessive utilization of fossil, fuels, such as poor air quality and greenhouse gas emissions. Hydrogen appears to be an attractive alternative to the conventional, fossil, fuels with better energy efficiency and less environmental, impact. Pd and Pd-based alloy are the most often used membranes for hydrogen separation due to their superiority over other membranes. However, the stability of the commonly-used thin Pd-based composite membranes at high temperatures still, remains a big challenge. In this presentation, we will, report our progress on thin Pd-Ru alloy composite membrane by electroless plating high temperature applications.

Jan 1, 2010

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

Single-unit separations in mineral processing are typically not able to meet the strict purity requirements for consumer markets. As a result, multistage separation circuits are often employed. Because these circuits represent a large and inflexible capital investment, process engineers are careful to ensure that the circuit is optimally designed to meet the desired objectives. The set of interdependent decisions that constitute the circuit design may involve the selection of different unit operations, different equipment specifications, different operational parameters, and different unit interconnections. To assist circuit designers in assessing these options, researchers have attempted to establish standard design methodologies that involve various techniques and tools.

By C. Jewell, G. H. Rupay

"67 - 2:15-3:00Regeneration of Hydrochloric Acid from Waste Pickle Liquor Using a Fluidized Bed Reactor System. G. H. RUPAY and C. JEWELL, Dominion Foundries and Steel Ltd., Hamilton, Ont.The disposal of acidic waste liquors from pickling processes has always been a problem for the steel industry. With increased awareness toward environmental control and the problems acidic wastes create, processes utilizing recovery and regeneration of the waste acids are becoming more popular. This paper describes the Keramchemie/Lurgi process for regenerating hydrochloric acid from waste pickle liquor using a fluidized bed reactor system. The process parameters are outlined, together with a brief description of the equipment. This is followed by a discussion of the operating problems and concludes with economic data."

Jan 1, 2000

By N Madani, Y Abildin, E Topal

Mine planning is a crucial part of all mining industry projects, and nowadays, geometallurgical mapping through advanced computer technologies provides an opportunity to involve metallurgical responses of a deposit into 3D block model in order to optimise mine planning activities, especially for production forecasting. Including these metallurgical parameters apart from traditional geology and grade-based attributes into resource modelling leads to an extensive approximation for the economic maximisation of mine production due to better forecasting, planning and increasing certainty and the reliability of the resource model (Macfarlane and Williams, 2014). Commonly, geostatistical techniques and algorithms are used to produce models with the high resolution (Brissette et al. 2014; Deutsch et al. 2014; Tolosana-Delgado et al. 2015). The accuracy of the modelling procedure deeply depends on a reliable block model, produced by spatial analysis of corresponding variables that define the geological, metallurgical, mineralogical and chemical behaviour of the deposit. However, there are special cases, where the application of enhanced geostatistical methods is required, to solve the occurred difficulties between variables with multivariate complexities. For example, in oxide copper deposits, the soluble copper grade is a percentage of total copper grade and recoverable by heap leaching processes (Emery, 2012; Hosseini and Asghari, 2015). Hence, the joint spatial modelling of these variables has two difficulties.CITATION:Abildin, Y, Madani, N and Topal, E, 2018. Forecast the mineral processing destinations based on spatial interpolation of geometallurgical variables, in Proceedings Complex Orebodies Conference 2018, pp 2–5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018