Search Documents

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By Robert M. Doerr

The oxidation kinetics of Ni-Y alloys in the range 0.04 to 8 weight-percent Y, and of high-purity Ni, were compared by the use of a sensitive volumetric apparatus. The reactions followed approximately the parabolic rate law; for oxidations in 02 at 0.5 atm and 1,200° C, the parabolic rate constant was about 0.37 + (0.064) (Y-2.11) mg cm-2 min-1/2, where Y represents the weight-percent Y in the alloy. Internal oxidation of Y occurred in the alloy specimens and the resultant Y203 particles, which were in patterns related to the eutectic structure of the alloys, served as markers showing that the subsequent oxidation of the surrounding Ni was by inward diffusion of O. The scale consisted in each case of NiO, but the inner parts of the scale on the alloy specimens included the patterned Y203 particles. The thicknesses of the inner parts of the scale depended directly on the Y concentration, and the thicknesses of the Y2O3-free outer parts of the scale were inversely related to the Y content of the alloys. There is thus a relationship between the thickness of the outer part of the scale and the protectivity of the scale. Outward diffusion of Ni and inward movement of 0, from the inner boundary of the Y2O3-free part of the scale, is proposed as a mechanism for these results.

Jan 1, 1966

1. Book reviews Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. (Reviewer: J. Keenan) Separation procedures in inorganic analysis. A practical handbook, by Roland S. Young. Charles Griffin, 1980. £23.00. (Reviewer: R. Murray-Smith) 2. Historical reprints Theinin~rs dictionary, by William Hooson. £14. Discovery of subterraneal treasure, by Gabriel Plattes. £12. Fodinae Regales (The Mines Royal), by Sir John Pettus. 3. De Beers' booklets Amborite - a remarkable new cutting material, by De Beers Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Booklet, 14 pp., free of charge. Natural and synthetic micron powders, by De Becrs Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Leaflet, 5 pp., free of charge. 4. New books Nickel in the environment, edited by J. O. Nriagu. New York, Wiley, 1980.928 pp. $65. Underwater minerals, by D. S. Cronan. London, Academic Press, 1980. 364 pp. $57.50. Data conversion integrated circuits, edited by D. Dooley. New York, Wiley, 1980.298 pp. $26.95 (cloth), $17.50 (paper). 5. NIM reports Report 2057 A mineralogical study of the Rooibokkop- Boschhoek copper deposit in the Marble Hall area. Report 2069 A utomatic setting of the distance between sample and detector in gamma-ray spectroscopy. Report 2070 The prereduction of chromites from the UG-2 Reef. Report 2075 The optimization of some of the conditions for analysis by spark-source mass spectrometry. Report 2082 A survey of the literature on gravity separation.

Jan 1, 1981

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

This report discusses the nonfuel critical minerals position of the United States-both current and future (to the year 2000). We have assumed that there will be no major global disturbances-military, political, or economic-during the rest of this century. However, international relationships, strategies, and conditions that affect the supply of minerals are very tenuous, normal trading patterns can be easily upset, and national and ideological objectives can and do interfere with "normal" free market conditions. For example, the Department of Defense has reported that the Soviet Union is engaged in a strategy designed to reduce the availability of strategic minerals, through either physical disruption, market manipulation, or domination of producing or neighboring states. Although such a strategy poses serious concerns for the United States and the free world, the impacts of disruptions are not covered in this publication. Historical Perspective The modern industrial economy of the United States is founded on the production and use of minerals.* Two hundred years ago our forebears began taming a raw continent, developing a base for agriculture and a rudimentary minerals producing system. In the 19th century, with the aid of imported labor and capital, the development of America's vast natural resources was undertaken, and the transition from an agricultural to industrial society was underway. By the century's close, the United States had emerged as a great industrial power, partly through the development of such mineral resources as iron in Minnesota and coal in Pennsylvania.

Jan 1, 1983

By Herty, C. H.

One of the numerous requirements of many grades of present- day steel is that the steel shall be free from non-metallic inclusions. These inclusions may be composed of oxides, sulphides, complex oxy- sulphides, and nitrides, which enter the steel with the furnace charge, result from sulphur absorption from the furnace gases, or are formed in the steel during the deoxidation process. Although few' data are available which indicate in any quantitative manner the specific effects of inclusions in steel, there is a large mass of circumstantial evidence which points to the advisability of producing steel free from these impurities for many purposes. At the present time there is a growing feeling among metallurgists that non-metallic inclusions should be divided into two distinct types: (I) those readily visible under the microscope at ordinary magnifications; and (2) those in colloidal suspension or in solid solution. Both types are profoundly influenced by the character of the charge, the manipulation of the furnace slag, and the method of deoxidation. The work described in this bulletin deals primarily with inclusions visible under the microscope at ordinary magnifications, but the steels made by the various methods of deoxidation are being used LO study certain effects which may be ascribed to the second classification, named above. This latter work will be the subject of further bulletins on the effect of deoxidation practice on the physical properties of the steels involved.

Jan 1, 1957

The Granites Gold Mine has far exceeded the design capacity of 300,000 tonne per annum during its first sixteen months of operation. The presence of considerable free coarse gold has made it imperative that the gravity section operate at maximum efficiency. The inadequacy of acid digest- ing facilities and trying climatic conditions prompted management to initi- ate investigations into the use of Intensive Cyanidation as an alternative method for upgrading gravity concentrates prior to smelting.

Jan 1, 1988

By Ronald J. Doll, John Elkin, M. P. Evans

The application of "Alignment Free” right angle shaft mounted drive systems offers improved reliability and reduced costs for surface and underground belt convey- ors. Comparisons to conventional approaches will cover installation, operating, maintenance, and spares inventory cost savings. Various options for belt acceleration and load control on fixed and variable length (booster) belt conveyors will be reviewed for operating performance, reliability, and total cost. Lastly, a case study of a successfully operating installation will be highlighted.

Jan 1, 1996

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By J R. Hearst, T R. Butkovich

Explosive-induced fracturing and permeability enhancement far from a free face were studied. A one-dimensional computer program, SOC, was used to predict the total failure-associated distortional strain, ef. Laboratory and field experiments associated the calculated ef with the observed fracture and permeability enhancement. An ef value of 0.015 corresponded to the observed radius of effect, which was about seven times the cavity radius and was consistent with predictions from SOC and from the literature.

Jan 1, 1976

By G. C. Xiao

A database, incorporating historical data from British mines, to study the factors affecting inflows from proximate aquifers into longwall workings, showed that a main casual factor was the immediate roof strata lithology. When this comprised principally stronger sandstone, there was a tendency for periodic inrushes associated with face weighting. This phenomenon is explained by the collection of water in bed sepa¬ration cavities, where free water connected to a high pressure head aquifer source, may be trapped.

Jan 1, 1990

By R. L. Montgomery

The literature has been surveyed and values recalculated for the heats and free energies of formation of solid rare-earth compounds at 298° K. In most instances it was necessary to estimate the entropies. Thermodynamic properties of aqueous rare-earth ions have also been calculated. INTRODUCTION The accumulation of thermochemical data on rare-earth compounds in recent years makes it possible to review the subject and to obtain more consistent and more reliable information than was available previously.

Jan 1, 1959

Carrying Energy ?Energy ?Power, data, signal, hydraulics, pneumatics? ?Needs to be conveyed from a stationary point to a system in motion ?Cable Carriers (steel and plastic), Festoon Systems, Cable Reels and Bus Bars Polymer Cable Carriers ?Life Line for modern machinery ?Transmitting power, data, signal, hydraulics or pneumatic energy ?Constructed and designed to work in harsh environments, at high speeds and to do this continuously ?Meet a wide variety of cable (Media) requirements ?Virtually maintenance free ?High efficiency

Nov 1, 2011

By Peter Kowalczyk

The acquisition of submarine gravity data using airborne gravity technology is a practical reality. Ocean Floor Geophysics plans to deploy a free-swimming ROV based submarine gravimeter on a commercial basis in early 2009. The submarine instrument is a variant of the well-used GT-1A airborne gravimeter. Airborne gravity surveys are now routine. The primary factor controlling the accuracy of airborne gravimeters is the precision of the GPS measurement of vertical movement of the sensor platform. The gravity measurements along a flight line are the differences between the output of the gravimeter vertical accelerometer and the estimate of the aircraft vertical acceleration using the differential GPS system. The principle difficulty of moving an airborne gravimeter to a free-swimming submarine platform is the necessity to have an accurate real time estimate of the changing elevation and hence changing vertical acceleration of the platform; GPS doesn't work underwater and an accurate estimate of depth fluctuations to the necessary precision is difficult to acquire. It is interesting that the airborne gravity gradiometer technology, which competes with the airborne gravity technology, was first developed as a classified military application for use by missile submarines during the cold war. Gradiometers were developed for this application specifically to avoid this problem. A gradiometer does not require as accurate an estimate of its vertical position to make a useful reading- it measures gravity gradients, not the gravity field itself.

Jan 1, 2008

By Kimberly Martin

The EFFC/DFI Carbon Calculator provides the deep foundations industry the opportunity to be a leader when it comes to carbon reduction. This tool was created 10 years ago in an extensive effort by the European Federation of Foundation Contractors (EFFC), DFI, member organizations and Carbone 4, a consultant with ex- perience in life cycle assessment. The tool was born out of the fact that governments and clients were asking for embodied carbon information for foundation systems, and that in- dividual companies were building their own calculators to meet these requests. To help all member organ- izations achieve compliance, and to have a sector-specific tool that is certified to the prevailing standards, EFFC and DFI agreed to partner to create the carbon calculator, which is: Excel based and, therefore, easy to learn and use Updated on a regular schedule Certified to ISO 14067, GHG Protocol and PAS 2050 Free and available for anyone to use Even though this tool is free and easy to use, most projects in the industry do not have a carbon calculation performed. The case to use the calculator is more obvious for members in places like Europe where there are stricter reporting standards and government work can be driven by sustainability over cost. In North America this is not the case, yet. Without directives from clients and governments, what can compel the industry to start regularly using this tool and care about the carbon emissions of projects during design and construction?

Nov 1, 2022

By J H. Kyle

Cyanide is a significant cost in gold processing, as well as an environmentally sensitive issue. It has been suggested that precipitation of cyanide from leach liquors as copper-iron-cyanide compounds such as Cu2Fe(CN)6 may account for part of the total cyanide consumption. This may be especially true for ores that are rich in both copper and iron minerals. Ammonia addition has been shown to decrease the cyanide consumption by copper. Cu2Fe(CN)6.xNH3 precipitates have also been postulated to form during conventional cyanide detoxification processes, using oxidants such as SO2/air, with ammonia arising as a breakdown product from the oxidation of free cyanide. The present work has examined the conditions under which such precipitates may form, particularly in gold plant process and detoxification liquors. Ammonia and pH were found to have a large effect on the extent of precipitation. The compounds that were formed were found to comprise mainly Cu2Fe(CN)6.7H2O, as well as a range of NH3-bearing variants. The stabilities of the various precipitates are important from an environmental perspective. The long-term stability of copper ferrocyanide precipitates in tailings dams may be a problem under alkaline conditions and when some free cyanide is present, elevating the measured total cyanide in solution significantly. Case studies including data from actual plants are also considered, and the importance of these effects is reaffirmed from these results.

Jan 1, 2000

By O Ostrovski

Iron ore reduction and iron cementation by CH4-H2-Ar gas was investigated in a laboratory isothermal fixed bed reactor. Iron ore was first reduced to metallic iron by hydrogen, then carburised to cementite by methane. Increasing temperature and hydrogen content accelerated the reduction process. Methane had almost no effect on the reduction process. Meanwhile, higher temperatures increased the rate of cementation and also the rate of free carbon deposition. The optimal temperature for cementite formation was found to be 750¦C. At this temperature, reduction of iron ore to cementite by gas containing 55 vol per cent hydrogen, 35 vol per cent methane and 10 vol per cent argon was completed in about 15 minutes. Addition of sulphur into the reducing/carburising gas strongly retarded the process of cementite formation and free carbon deposition. Cementite is an unstable phase which decomposes to iron and carbon. The rate of cementite decomposition increased with temperature up to 600¦C and above 750¦C . In the temperature range from 600¦C to 750¦C the rate of cementite decomposition decreased with temperature. Cementite was the most stable at 750¦C and least stable at 600¦C. The two-interface grain model was used to describe the process of iron ore reduction and the volume reaction model was employed to model the iron cementation process. The simulated results for both reduction and cementation are consistent with the experimental data.

Jan 1, 2000

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the recrystallization temperature of titanium has been investigated. All additions, except columbium and tungsten, raised the recrystallization temperature. A correlation is obtained between the logarithm of the absolute rate of change of recrystallization temperature with atomic percent solute and the number of uuter d shell electrons attributed to the free atom of the solute element in its ground state. The work of Abrahamson, et aL.1-6 on dilute binary solid solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and recrystallization temperature. It is shown in these studies that the number of outer s and d electrons in the solute are of prime importance in determining the absolute rate of change of recrystallization or transition temperature with composition. Furthermore, the limit of initial linearity (in the curve of recrystallization temperature vs at. pct solute) has been shown to be a function of the number of d shell electrons in the solute for dilute iron- and vanadium-base alloys. To date no complete systematic recrystallization study of dilute binary titanium base alloys has been made. This study together with that of zirconium base alloys 6 will provide the data for the comparison of the effect of the same solutes upon two solvents with the same number of outer d shell electrons.

Jan 1, 1962

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

HENRY M. HOWE, Bedford Hills, N. T. (communication to the Secretary?).-The authors valuable results as to the effects of the air-hardening temperature on high-speed steel may be summed up thus: Influence of Rising Air-Hardening Temperature on. High-Speed Steel Air-hardening microstructure Cutting Properties temperature S Austenite Grain Free Carbide Grains Boundaries Too low Small or Narrow Maximum Too soft undeveloped Intermediate, Well-developed Intermediate Little or even Best correct none Too high Coarse hide, even with Minimum . Weak, brittle, three-rayed crumbling stars Here the suggestion is that as the air-hardening temperature rises it causes two prominent effects, one helpful and the other harmful, the increase of the former exceeding that; of the latter up to a certain point, at which the steel is most useful, and then in turn being outrun by it. The first is the progressive dissolving of the free carbide in the austenite, increasing the stability of the red-hard state. The second is the progressive coarsening of the grains, and thickening of the intergranular cement, developing at last into spandril-like three-rayed stars of the 1,288° specimen. (2,350° F.) of Plate D, thus giving clear proof of incipient fusion, that is of crossing the solidus. This causes intergranular weakness. The individual grains may have great red-hardness, but they do not cohere. They approach the condition of a bag of emery grains.

Jan 6, 1917