Search Documents

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By S. W. Parr, T. E. Layng

There is presented below the results of experiments made on six samples of Utah coals furnished through the U. S. Bureau of Mines , under an agreement dated June 16th , 1920. The details of all values for all runs are tabulated and presented herewith . Clear The samples, consisting of approximately 150 pounds each, were received at the University of Illinois , on June 15 , 1920 , and are listed as follows : Creek , Wattis , Castle Gate , King , Standard , and Aberdeen . The proximate and ultimate, analyses of the various ccals from that region , representing all the types included in these samples , have already been made by the Bureau of Mines , and are available . * Similar determinations were also made on the particular samples forwarded for purposes of these experiments . The results obtained on the coal as received did . not very in any material feature from the values reported by the Bureau, they are shown in Table 1. It is of importance to note only that the oxygen content is uniformly high , namely approximately 9.5 to 11.5 per cent of the as- received coal , while the oxygen - hydrogen ratio is also high, being on the average approximately 2 ( oxygen) to 1 ( hydrogen) .

Sep 1, 1921

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions, which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws governing the Portuguese overseas possessions, prepared from the best avail- able information in Washington, has been slightly amplified in accordance with suggestions transmitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By Filippo Verlezza

The 3-roll technology is a recognized process applied to SBQ production. The main aim of this paper is to show the latest developments on this technology including other equipment´s that also contributes for a better performance on SBQ coils production.

Jul 30, 2018

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

By M. Mentser

The exchange of oxygen between carbon dioxide and carbon monoxide that occurs reversibly on carbon surfaces was studied at temperatures of 750° to 850°C and a pressure of 1 atmosphere. Carbon-14 was used to detect and measure the exchange reaction. The extent of oxygen exchange was a linear function of com- position of the gas mixture, and this relationship was used to evaluate the forward and backward rate constants of the reaction. Equilibrium constants, directly determined for oxygen exchange in this study, agreed well with values in the literature that were derived only by indirect procedures. This result establishes the validity of oxygen exchange in the mechanism of carbon gasification by CO2. Rates of carbon gasification were less than an order of magnitude slower than rates of oxygen exchange. Activation energies for these two processes were 58 and 53 kcal/mole, respectively. The closeness in the activation energies argues against any change in the rate-controlling step over a wide temperature span at atmospheric pressure. The role of CO as a retardant on the CO2-C reaction, and the nature of the carbon-oxygen complex are also discussed in view of the data obtained.

Jan 1, 1973

By R. S. Dean

In an earlier paper Dean and Hersberger5/ gave preliminary results a d discussed briefly the use in flotation of organic reagents of the type known in the textile industry as "wetting agents.? These reagents are those with a molecular structure comprising a long hydrocarbon chain attached to a. highly molar or hydrorhile group in such manner that ionization is nearly complete in dilute solution and the resultant ionic grouping has a very considerable hydrophile-lipophile unbalance in the structure. As a result of this characteristic structure these reagents are more or less powerful frothers and emulsifiers. Ten the degree of hydrophile-lipaphile unbalance is sufficiently great and specific chemical factors are absent these compounds behave in flotation as noncollecting frothers insensitive to reason¬able changes of pH.

Jan 1, 1937

By R. S. Dean

In an earlier paper Dean and Hersberger5/ gave preliminary results a d discussed briefly the use in flotation of organic reagents of the type known in the textile industry as "wetting agents.? These reagents are those with a molecular structure comprising a long hydrocarbon chain attached to a. highly molar or hydrophile group in such manner that ionization is nearly complete in dilute solution and the resultant ionic grouping has a very considerable hydrophile-lipophile unbalance in the structure. As a result of this characteristic structure these reagents are more or less powerful frothers and emulsifiers. Ten the degree of bydrophile-lipaphile unbalance is sufficiently great and specific chemical factors are absent these compounds behave in flotation as noncollecting frothers insensitive to reasonable changes of pH.

Jan 1, 1937

By John B. Goodman

This report summarizes the work done by the Koppers Company, Incorporated, in cooperation with the Bureau of Mines on the commercial evaluation of the primary low-temperature tars produced from Texas lignite in the Rockdale, Tex., plant of the Aluminum Company of America in conjunction with the Texas Power and Light Company. The interest of the Bureau of Mines in this project is twofold. First, through its cooperative agreement with the Texas Power and Light Company the Bureau has assisted in the technical design and practical operation of the prototype, externally heated, entrained-state carbonizer for producing char for electric-power production and for primary low-temperature tar. Second, the first successful operation of the prototype carbonizers employing the Bureau of Mines-Parry process on lignitic coal in 1953-54 led to the production of large quantities of primary lignitic tar, concerning which too little was known or had heretofore been published in this country.

Jan 1, 1959

By Murray Greyson

A number of tests were made with various methanation catalysts in fixed-bed, conventional fluidized-bed, and multiple-feed, fluidized-bed equipment to develop catalysts and processes for methanation of synthesis gas. The results show: 1. Methanation reactions may be carried out in 1-inch, bench-scale equipment at high synthesis-gas throughputs with good temperature control of the reactions if a multiple-feed type of fluidized-bed design is used. 2. Nickel is superior to iron as a catalyst for the methanation of synthesis gas, unless the process is considered in terms of a combined operation that produces both gaseous and liquid products. 3. Techniques of catalyst preparation determine, to a large extent, the process life of nickel catalysts, and these techniques must be thoroughly investigated before any conclusions can be reached. 4. Enough data are available to indicate that the sulfur concentrations in synthesis gas that is used for methanation are extremely critical, and maximum process limits should be carefully evaluated.

Jan 1, 1955

By Edgar Peek

"The two dominant metallurgical problems in treating most base metal sulphide concentrates in both the chloride and sulphate system are iron removal and sulphur elimination, respectively [1-3]. In this paper the opportunities, limitations and fundamentals of the chloride metallurgy system are described against this background. Only the treatment of oxide and sulphide ores is considered. Both hydrometallurgical and pyrometallurgical unit process operations are highlighted, since most successful base metal processes are based on a combination of the two. Hence, an overview of the technical and also some economical aspects of chloride metallurgy are presented.This overview summarizes the successful applications of chloride metallurgy, but it will not give exhaustive process and plant descriptions. It predominantly focuses on the essential technical features of the metallurgical unit process operations, while providing numerous references separately."

Jan 1, 2011

By R. R. Allen

[The utilization of Western coals and lignite is a continuing study of the Bureau of Mines, and storage of these fuels is of paramount importance. Since the seasonal demand for coal in the Western States triples between the summer and winter months, successful storage of these low-rank fuels would tend to level out this variation and should reduce fuel costs. The time is rapidly approaching when the West Coast States, particularly California, will annually import several million tons of coal from the Rocky Mountain States for additional power production. This will necessitate storage of large quantities of coal, and it is thefore important to develop experience in such storage. Dry surface storage, by virtue of its flexibility and low cost, is particularly adapted to the stockpiling of large quantities of coal. This report will, therefore be primarily concerned with such storage. Inasmuch as the problems of dry, open-pit storage are quite similar to those of surface stockpiling, experiences in pit storage will be discussed briefly. Although spontaneous combustion is a hazard in storing coal, experience has proved that heats can be avoided by proper stockpiling procedures. The purpose of this report is to show that the most reactive coals can be stored satisfactorily on the surface by avoiding segregation and by thorough compaction.]

Jan 1, 1954

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934

By The Staff

Introduction It is the purpose of this paper to discuss a number of the metallurgical improvements in the technology of copper-nickel ore treatment which have been introduced during recent years in the plants of ?the International Nickel Company of Canada, Limited. In common with other ore treatment processes, the procedure for extracting nickel and copper is changing almost continuous! y. These changes are necessitated by reason of changes in ore grades and characteristics, rising material and labour charges, and the constant drive to maximize metal recovery and to minimize production costs. It is not possible to present a comprehensive list of all the changes made, and only a selected number of the improvements in the milling, smelting, and refining operations are covered. It should be clearly understood that some phases of the procedures described have been pioneered by others in kindred fields and due acknowledgment is given to their foresight and efforts. Articles have been published over the years describing the operations of the International Nickel Company plants and the reader is referred to the Engineering and Mining Journal, Vol. 130, No. 9, November 10th, 1930, and to the Canadian Mining Journal, Vol. 58, No. 11, November, 1937, and Vol. 67, No. 5, May, 1946. Other references are the Transactions of this Institute, 1932, 1938, and 1946; Metals Technology, American Institute of Mining and Metallurgical Engineers, February, 1938, and Canadian Chemistry and Process Industries, April, 1940.

Jan 1, 1948

By J Millard, K Sexsmith

BHP Billiton Diamonds Inc (BHPB) has been mining kimberlite from several pipes at the Ekati Diamond MineTM located 300 km north of Yellowknife since 1997. Processing of kimberlite produces coarse kimberlite rejects (CKR, 0.5 to 8 mm) and fine tailings (less than 0.5 mm). The CKR are trucked to the Coarse Kimberlite Reject Storage Area (CKRSA) located within the drainage area of the tailings impoundment (Long Lake Containment Facility û LLCF). The coarse rejects are wet when dumped and are expected to freeze as a result of annual average site temperatures of about -10¦C. Seasonal thawing occurs along the exposed edges of the pile. Monitoring of the CKR indicates they have consistently low sulfur concentrations (0.4 per cent) accompanied by high acid neutralisation potentials (78 to 337 kg CaCO3/t). Carbonate concentrations vary from 0.9 per cent to 3.4 per cent. The CKR are therefore not potentially acid generating based on conventional laboratory testing. Monitoring of stagnant pools on the tundra downgradient of the CKRSA has shown that water originating from the pile resembles acid rock drainage (ARD). Water pHs can be less than 4, and sulfate concentrations are typically in the thousands of milligrams per litre. Conventional flowing toe seeps are pH neutral but also have elevated sulfate concentrations. Investigations conducted in the summer of 2002 revealed no evidence of in situ acid generation. Pore water chemistry is probably controlled by oxidation of fine-grained pyrite, neutralisation of acidity by calcium and magnesium carbonates and silicates, and freeze concentration of pore water. The acidity observed in tundra pools downgradient of the CKRSA appears to be a result of leaching and mobilisation of iron under reducing conditions at the CKR-soil contact. Downstream of the CKRSA, reduced iron oxidises and is hydrolysed on contact with the atmosphere causing pH depression. BHPB is applying the findings of this study by constructing facilities containing kimberlite on granite pads. These in turn are placed on frozen ground so that the foundations remain frozen and limits contact of wastes with the acidic soils.

Jan 1, 2003

By D. Bienstock

In connection with air-pollution studies, the Bureau of Mines is cooperating with the U.S. Public Health Service in investigating the use of solids for removing sulfur dioxide in concentrations of less than 0.5 percent from combustion and waste gases. Removal of sulfur dioxide at flue-gas tempera¬tures would no longer result in the cooling of scrubbed gas, which is inherent to liquid scrubbing processes used exclusively in industry today. Results are reported of extensive investigation, using metallic oxides as absorbents, adsorbents, and oxidation catalysts at 130° and 330° C. (temperatures at which flue gas may be treated in powerplant practice). The most active absorbents tested were the oxides of manganese, cobalt, copper, and alkalized alumina; 23 to 33 grams of sulfur dioxidn were removed by 100 grams of absorbent at 130° C., while scrubbing more than 90 percent of the sulfur dioxide from a simulated flue gas, and 19 to 61 grams of sulfur dioxide were removed at 330° C. A more detailed study is reported on absorption and regeneration, using manganese oxides and alkalized alumina. Adsorption of sulfur dioxide on activated carbons and molecular sieves at elevated temperatures is considerably less efficient than removal by absorption--a maximum of 7 to 8 grams of sulfur dioxide could be removed with 100 grams of adsorbent at 130° C. A potash-promoted vanadium pentoxide is effective in converting sulfur dioxide to trioxide; complete conversion in a simulated flue gas containing 0.35 percent sulfur dioxide was obtained at 365° C. Pilot-plant and cost studies are being made by the Bureau to determine the economic feasibility of removing on an industrial scale the sulfur dioxide present in gases in low concentrations.

Jan 1, 1961

By R. D. Brown

This Bureau of Mines report describes a new methodology for identifying and sorting scrap metals using two modern portable instruments: a thermoelectric sorter and a hand-held emission spectroscope. The method, tested on a 27-sample stainless steel and superalloy array, makes it possible to group and/or identify a typical mixture of high-value metal scrap in two or three steps, whereas as many as seven or eight steps are needed to perform the same separations using chemical spot tests. A portable fluorescent X-ray analyzer identified 19 of the 27 alloys in the sample array by name or type; these alloys are included in the microprocessor memory. The remaining alloys were identified by using the analyzer in its elemental analysis mode and comparing the results wit.h alloy specification chemistry.

Jan 1, 1984