Search Documents

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By I. Ohnaka

Although many works have been reported on the semisolid casting, the mold filling behavior of semi-solid alloys has not been so well understood. This paper compares the physical and numerical simulation results on the mold filling behavior. Physical simulation was performed by using solid-water mixture. The numerical simulation was made under the assumption of one phase flow with an effective viscosity. It was found that the solid particles stabilize the flow greatly if the kaction solid exceeds about 0.4, because viscosity increases greatly. The overall flow behavior can be estimated by the numerical simulation. Interesting flow behavior was also found which can not be observed in the case of one phase flow and which is difficult to simulate by the one phase flow assumption.

Jan 1, 1997

By J. O. Lewis

In its efforts to reduce waste, and increase efficiencyin oil production, the Bureau of Mines is investigating methods of increasing the recovery from the underground sources of supply, which are the foundation of the petroleum industry and the many allied industries wholly or partly dependent on it. In the face of a demand that is increasing faster than the production and that, in the consensus of opinions of well-informed authorities, is soon likely to outstrip the productive capacity, it is well to consider whether it is not possible to extract more oil from the known sources of supply. It is universally acknowledged that by the usual production methods much oil is left underground, the general opinion being that at least 50 per cent of the oil in a field remains unrecovered when the field is abandoned as exhausted. From the writer's own investigations he believes the average recovery is even less, and if any considerable portion of this oil being left underground could he made available it would have a tremendously favorable influence on the petroleum industry and all the industries dependent on it. In this publication are considered the principles involved in increasing recovery and methods of extracting more oil from the oilbearing formations than by the usual ways of producing. These methods are: The use of gas or vacuum pumps, forcing compressed air or gas through the oil-bearing formations, displacing the oil by water, and better utilization of the natural pressures in the oilhearing formations. Especial attention is being given to a processcommonly known as the Smith-Dunn-for forcing compressed air through oil-bearing formations because it is believed to hold most promise for the future.

Jan 1, 1917

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By E. H. Holm

"This paper is a market-oriented review of the industry's present and forecasted performance, considering some of the principal factors influencing natural resource development. The author illustrates the steady consumption growth of nickel, and stresses the need for a quantitative long-range approach to production, consumption and the supply/ demand balance on a worldwide basis. Objective consideration of this data exposes some popular misconceptions. The possibility of near-term undersupply of nickel is discussed in relation to historically rapid changes in inventories and demand patterns. What is the significance of the increasing reliance on lateritic sources? New• facilities, new processing methods and new product forms are illustrated as further evidence of the industry's determination to satisfy the needs and preferences of nickel consumers. Examples indicate how product forms must accommodate to fast-evolving end-use technology. A review of nickel's price performance is used as a base from which to explore tomorrow's price trends."

Jan 1, 1972

By S. Jayasekera, A. M. T. S. Bandara, J. Kyle, E. Koenigsberger, L. Koenigsberger

The extraction of rare earth oxides from fluoroapatite rich phosphate concentrates often involves a weak acid leach of fluoroapatite and a sulphuric acid bake of the leach residue followed by water leach and precipitation to obtain an intermediate product. The main aim of this study was to determine and rationalize the solubility of rare earth metal ions in synthetic solutions representing various process liquors at the temperatures 40, 60 and 80oC. The liquors contained different acid and metal ion concentrations with respect to sulphuric acid, phosphoric acid and sulphate salts of sodium, magnesium, aluminium, potassium, calcium and iron(III). A solid of mixed rare earth carbonates was used as the source of rare earth metal ions. The solubility tests and characterization of solids using XRD were conducted at Murdoch University laboratories as part of the process development for the Arafura Resources Nolans rare earth project. The composition of initial carbonate solids and the solids and solutions formed after saturation were analysed for rare earth and other elements at TSW Analytical Laboratories in Perth using ICP-MS and ICP-OES. The precipitated solid in sodium-rich acidic sulphate solutions is the double salt NaRE(SO4)2 based on the solid assays. However, in acidic solutions free of sodium or of low concentrations of sodium the precipitated solid appears to be RE2(SO4)3.

Jan 1, 2014

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

By W. K. Cunningham, Edwin A. Gee

"INTRODUCTION This paper is one of many reporting on various aspects of the Bureau of Mines program during World War II directed toward alleviation of shortages in certain critical minerals some of these papers are published as technical papers information circulars, and reports of investigations, of the Bureau of Mines or in technical journals.The investigation described in this report was begun as part of the Bureau, of Mines program to develop acid processes for the extraction of alumina from low-grade bauxites and clays. A domestic shortage of high-grade bauxite suitable for treatment by the Bayer process became acute as a result of World War II; and intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted.A survey of the various methods for extraction of alumina from clay has been presented in an early Bureau of Mines publication. 4/ The principal barrier to the successful operation of an acid process has been the difficulty experienced in developing a suitable commercial method for purifying the crude aluminum salts after the clay extraction is complete. Iron salts are the foremost contamination influence. A review of the more prominent procedures that have been proposed for separating iron and aluminum salts can be found in the well-known text on aluminum by Edwards, Frary, and Jeffries. 5/The majority of acid processes to extract alumina from clay employ sulfuric acid as the leaching agent, and the purification is thus reduced to the separation of iron and aluminum, sulfates."

Feb 1, 1948

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By W. H. Oppelt

A lignite from west-central North Dakota (Mercer County) was dried by the Bureau of Mines by the Fleissner process at saturated steam pressures to 1,500 pounds per square inch absolute (p.s.i.a.). Normally, the process is operated at pressures of 200 to 370 p.s.i.a. At the highest pressure the temperature of the saturated stearn is 596° F. The purpose of the investigation was to evaluate the influence of very high stearn pressure and temperature on moisture removal, steam consumption, and physical and chemical characteristics of the dried lignite. Two drying cycles were used: A normal cycle, corresponding to previously established standard time requirements, and an accelerated cycle, wherein time requirements were determined by boiler capacity and handling speed. Blank tests to determine stearn requirements for heating the empty autoclave were performed for each cycle and each test condition. Moisture removal, final moisture content, net steam consumption, and size stability of the dried lignite were determined.

Jan 1, 1959

Jan 1, 1897

Batch centrifugal gravity concentrators have become standard equipment in gold grinding circuits for recovery of gravity recoverable gold (GRG). The downstream benefits of installing a gravity circuit are well understood, and in general, if there is a reasonable amount of GRG in the ore, a gravity circuit is usually installed. The benefits of gold gravity recovery have also been well documented, with a large database of successful case studies. As well, predicting production scale gravity recovery results ahead of installing gravity has become a common practice. The missing link between lab and full scale has always been the ability to predict the recovery benefit of installing gravity ahead of actually doing so. Being able to predict the recovery benefit in advance would help an operation in assessing the economic benefit and help justify the capital costs of the gravity circuit with much less uncertainty.

Aug 1, 2010

By Robert L. Lagace

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal minus. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to determine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m2 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to he attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

By John J. Mahoney, George P. Demopoulos, Matthew T. Bohan

In recent times processing of arsenic-laden complex ores and heightened awareness of the detrimental health effects of arsenic has put an increasing burden on metallurgical operations to remove arsenic from processes for disposal in an environmentally stable form. At present, arsenic is removed and prepared for storage by precipitation of insoluble secondary arsenic-bearing minerals. It has been suggested that Ca(II)-Fe(III)-As(V) phases resembling the natural mineral yukonite, under certain conditions, may have a role in controlling arsenic pore water concentrations in arsenical waste storage facilities. In this study, a previous synthesis method of yukonite (Ca3Fe5(AsO4)4(OH)9⋅4H2O) is revisited and new solubility/stability data is presented based on a modified method.

Jan 1, 2014

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995