Search Documents

By D. Naden

Sulphuric acid leaching is the most common method of recovering uranium from its ores and in the following discussion various alternative low cost routes are investigated for recovering uranium from milled ore acid leach liquors. Historically uranium has been recovered from dilute impure leach liquors by packed bed ion exchange (IX), solvent extraction (SX) or a combination of both. All three process routes as commonly practised require complete separation of leached solids and liquids, as well as extensive solids washing in order to reduce soluble uranium losses to a minimum. Separation and washing are costly and often require equipment covering large areas of land. The size and capital cost of the post leach solids washing operation is controlled by the ease of washing the slimes fraction of the ore and the key to the problem of cost reduction, as many others have realised, lies in the ability to separate the slimes fraction of the ore from the more easily washed sands, to wash the sands in low cost equipment and to recover uranium from the slimes stream. Sands and slimes are usually defined in this context as the material larger than, and smaller than, 325 mesh (44 microns). The proposed flowsheets which minimise solid-liquid separation and washing have usually incorporated ion exchange (Refs 1,2,3), and resin in pulp is in fact practised in several mills in the USA (Ref 1). The resins used in these flowsheets and [cranium] recovery throughout the world have been strong base resins which load rapidly and are moderately selective for the uranyl sulphate complex anion over the range of pH which is conveniently achieved in an acid leach operation. Strong base resins are, however, not as selective as weak base resins and weak base liquid reagents owing to the adsorption of competing anions, some of which find their way into the product while others act as resins poisons. Ion exchange using strong base resins must therefore be followed by a more selective weak base SX purification step if pure yellow cake is required.

Jan 1, 1976

By M. E. Adam

This report describes the construction and testing of large (30 ft high by 55 ft wide) stopping and overcast structures in an oil shale mine. The work was undertaken to develop construction techniques and cost data, and to measure leakage rates on full scale structures in an oil shale mine. A design data base was developed by reviewing industry practice, oil shale industry plans, and technical literature. Alternate layouts for room and pillar mining were examined to find ways to reduce the size and number of ventilation control structures. Six full size stoppings and one overcast were built in the Colony Pilot Mine. Leakage rates were measured using both SF6 tracer gas techniques and the ?brattice window? method. The leakage was measured both before and after a full scale face blast. Blast air pressures were measured across two of the stoppings. Cost and leakage data were used to evaluate the projected overall performance of various combinations of the stoppings in a two-panel oil shale mine.

Jan 1, 1986

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By Thomas T. Read

I. INTRODUCTION. WHEN so much has been written upon a subject on which so little definite information is available as upon this, some reason must needs be assigned for adding to the volume of literature. A sufficient reason is found in the probable great future importance of China as a producer of mineral wealth. The present undeveloped state of mining in the Empire is due to many causes, among which the most important are the relatively simple needs of the population, the lack of transportation-facilities, the inelastic regulations governing the industry, and the superstitious reluctance of the people to make excavations which might disturb the spirits of the earth and air, or of ancestors. Iron is the metal most in demand, yet the needs of the population, until recently, only made necessary a production of approximately 0.5 lb. of iron per capita per year. The present annual production of iron for domestic consumption, in the United States, is nearly 600 lb. per capita. The curious state of development of transportation in this interesting country has been a greater handicap upon the mining industry than upon any other. The point upon which it hinges is the absence of a road-system. Except for a few military roads, now almost impassable, there are no roads in China; that is to say, there is no land which is set aside as a right of way, belonging to the commonwealth. Throughout the agricultural districts, generally speaking, the entire area is in private ownership, and the lines of travel are between fields. There is a constant struggle for existence between the owners of the land and the traveling public, with the natural result that the so-called roads usually

Mar 1, 1912

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By Robert H. Peters

This report presents findings from a Bureau of Mines study on barriers that may prevent miners from correcting and avoiding groundfall hazards. Such barriers stem from four basic types of problems: (1) inability to recognize groundfall hazards, (2) inability to correct groundfall hazards, (3) lack of motivation to search for groundfall hazards, and (4) lack of motivation to correct groundfall hazards. Data are presented that summarize the views of miners, section supervisors, and mine inspectors about the contribution of these barriers to groundfall accidents and what they think should be done to reduce the frequency of injuries sustained by falls of roof and rib. The report also includes a summary of miners' responses concerning their recent experiences with groundfall accidents, along with industrywide statistics on accidents and injuries caused by ground falls in underground coal mines.

Jan 1, 1987

By John R. McWilliams

The technological and economic pattern of the U. S. mining industry has undergone a rapid and continuing change since World War II. To provide realistic up-to-date cost data and to disseminate knowledge of technical developments, the Federal Bureau of Mines, with the cooperation of individual mining companies, is presenting a series of mining methods and costs reports similar to those it issued before 1939. Shaft sinking has always played an important part in mine development and [ration] and is an appropriate subject for this series of reports. Shafts [are] especially important in areas such as the Coeur d'Alene district of Idaho, where every major mine is served by one or more shafts and shaft sinking is in progress at one mine or and her almost continuously.

Jan 1, 1960

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By CHARLES R. KETES

I. INTRODUCTORY. INDUSTRIALLY, the most important service that geological science can now render to mining in the Upper Mississippi leadand zinc-fields is to devise some practical scheme whereby the productive ore-belts may be located with greater certainty than they have been in the past. Up to the present time there has been little service of this kind, and in spite of all that has been worked out concerning the geologic features of the region, and notwithstanding all that has been written about these ore-deposits, this particular phase of the subject has been, for some reason or other, the very one that has received the least consideration. The neglect by geologists in this respect has been all but complete. The following notes are suggestive of some practical solutions to the problems presented. As here suggested, the geologic relationships of the ore-bodies were surmised some years ago, though somewhat vaguely perhaps. No opportunity for securing critical data appeared until recent investigations of a private character were undertaken, which bad in view the extensive prospecting of undeveloped areas. Fresh from rather wide experiences of a decade in the principal mining-regions of four continents, and after a lenstrum's residence among the chief mining-camps of the West and of Mexico, under conditions which measured geologic hypotheses in meters and rigidly tested their values in, terms of dollars, the recent return to the Joplin field and a new survey of its ore-conditions were fraught with somewhat unexpected results. Aspects of the ore-deposition were presented of which previously there was no hint. Ten years' absence from the district had tended greatly to clarify former hazy impressions. It enabled many features, then only dimly outlined, to be considered more nearly in their true perspective and in their real relationships to their surroundings. It permitted a great mass of details collected a dozen years before in connection with the work of the Missouri Geological Survey to be viewed under new light and to

Feb 1, 1909

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By R. D. Currie

A study of the accident statistics in the coal mining industry convinces one that an organized effort must be put forth to prevent the vast destruction of human life in this industry . The fatality rate in Pennsylvania has not improved in the past several years and during 1928 it was higher than the average for the period 1916 to 1927 , inclusive . Although the accident rate for this State is less than that of the coal mines of the United States as a whole , nevertheless the rate is unduly high ; however , there are many companies which have exceptionally good records as regards both fatal and nonfatal accidents . A study of the methods used by some of these relatively good- record companies to reduce accidents in their mines shows that they exert an organized effort to prevent accidents , and that their safety organizations usually affect every employee in and about the mine from the highest official to the check boy . The chief executive must be actively and personally interested in accident prevention if real safety results are to be obtained ; when he shows this interest it is almost invariably reflected in the officials under him and throughout the organization . Safety organizations vary in form and are readily changed or adapted to the varying conditions found in the bituminous field . The companies whose organizations were studied in preparing this report are all getting good results , and it is their opinion that the safety organizations have been a big factor in obtaining these results . At their request the identity of some of the companies whose organizations were studied has not been divulged in this paper , but this does not affect the value of the information concerning their safety organizations .

Mar 1, 1931

By ARCH L. FOSTER

The rapid increase in the mmber of automobiles during the last 25 years has resulted in the insistent and growing demand for better roads of more permanent construction. Some form of State license for the operation of automobiles has been in effect almost from the time of the first "self-propelled" vehicle, and some part of the revenue derived from the sale of these licenses has been applied to the maintenance and construction of roads. However, to obtain funds with which to build their present highway systems, the individual States have resorted to the taxation of gasoline. The first State to adopt a gasoline tax was Oregon, the law becoming effective February 25, 1919. By 1928, all of the States except two had levied taxes on gasoline at rates varying from 2 to 5 cents per gallon. New York and Massachusetts passed gasoline tax laws which became effective in 1929. Regulations governing the quality and the methods of handling gasoline and other petroleum products sold in the States have also been adopted by 29 States; many of these laws antedate the adoption of a gasoline tax. The variations in motor fuel speci- fications and methods of test have been pronounced in the several States. The Bureau of Mines, in making certain technical studies of the rasolines marketed throughout the United States, the results of which are reported in its semiannual motor gasoline surveys and other reports, has had occasion to obtain and compile all of the present (April 1, 1931) tax and pection laws of the several States which relate to motor fuel and other petroleum products. To facilitate the use of this material and to obviate the need in most cases of reading the complete text of the laws as published by the States, the pertinent information was arranged in tabular form for cly reference. 3 Although digests of States gasoline tax laws' are available and copies of the complete laws can be obtained from the State agancies in charge of the enforcement of gasoline tax and inspection laws, it is believed that

Jan 1, 1932

By A. U. Miller

Since coal -mining records have been kept , reports of all mining States show that each year the lives of many workers have been sacrificed in the production of coal , and Illinois has contributed its share , Illinois reports for the 50 years 1882 to 1932 , inclusive , show that 6,673 men were killed -- 6,121 underground , 340 in the shaft , and 212 on the surface . Of the fatalities underground , 3,116 were caused by falls of roof or sides , 1,111 by haulage , 630 by explosives , 577 by gas explosions , 139 by electricity, and 548 by other causes ; 166 of the shaft fatalities were caused by falling down the shaft , 143 by the cage , and 31 by other causes ; 108 of the surface fatalities were caused by railroad cars , 46 by machinery , and 58 by other causes . Most of those engaged in mining are still of the opinion that it is an extremely hazardous occupation and that it is practically impossible to operate without accidents ; however , students of safety in mining now believe that with the proper attention to accident prevention mining may be conducted with little , if any , greater accident rate than that of other supposedly hazardous industries . There is no mystery connected with accidents in mining ; reports show that the majority are due to two main causes , falls of roof and sides and haulage . Mining companies in Illinois , as well as in other States , have proved in the past few years that the hazards of mining , like those of other industries , can be controlled to a large extent and the mines operated with few if any accidents , provided a great enough effort is made by employer and worker . Although the past accident rate of Illinois may compare favorably with that of other mining States it is higher than it should be ; the fact that 6,673 men (an average of 133.46 per year) were killed in and around the mines of the State between 1882- and 1932 indicates that accident prevention should receive more consideration in the future than in the past .

Nov 1, 1934

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

By C. Yi, M. Onifade, B. Genc, S. Dineva, T. Zvarivadza, M. Khandelwal

Deep hardrock mines worldwide increasingly face rockbursts as mining depths increase. These events result from the accumulation and sudden release of stress, causing rockmass damage and posing major safety and operational challenges. This paper focuses on destress blasting as a critical strategy to mitigate rockburst hazards. Although limited practical experience exists in Swedish deep hardrock mines, international case studies demonstrate that, when well implemented, destress blasting redistributes peak stresses by promoting controlled fracturing around mining excavations. The success of such techniques is highly dependent on site-specific factors such as stress regime, rockmass brittleness, structural geology, and blast layout. Although destress blasting is especially effective in massive, brittle rock under high stress, typical conditions for strainburst prone environments, its design cannot rely solely on numerical models. Simulations can offer preliminary evaluation of stress redistribution trends and guide early design assessments but their current limitations, including sensitivity to input data and simplified fracture mechanics, mean they are best used as supplementary tools rather than final decision-makers. Field trials, supported by microseismic analysis and fracture mapping, remain essential for validation. The study critically synthesises international experiences and presents a structured framework for destress blasting design, offering practical and academic perspectives aligned with Swedish geological conditions to support safer and more efficient application in deep hardrock mines.

Jun 27, 2025

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011