Search Documents

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By F. L. Pirkle, W. C. Bagby

"In his 1989 book, The New Realities, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, Claremont, CA, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized” (p. 209).The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze and interpret data that are material to a mineral-valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral-valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality and transparency, the three pillars of mineral valuation (minerals valuation, mineral-property valuation).The International Mineral Valuation Standards Template (IMVAL Template), third edition dated May 2018, defines mineral valuation as: “The estimation of the value of a mineral property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the valuation conclusion) or to refer to the preparation of the estimated value (the act of valuing)” (p. 14).Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The template deals with valuation, which is distinct from evaluation. The distinction inherent in these defined terms is that valuation addresses the estimation of value of a mineral property, whereas evaluation addresses the broader assessment of a mineral property for an investment decision (p. 2).”This is an important difference because the minerals industry commonly makes investment decisions using feasibility studies to evaluate a proposed mineral development and production project. The purpose of such investment-decision analysis is distinctly different from valuation of a mineral property, no matter where that property lies upon the mineral explorationdevelopment- production-reclamation timeline (Fig. 1). Valuation involves terms such as market value, just compensation, fair value, etc., whereas investment-decision analysis is concerned with the economic viability of a given proposed project. Although feasibility analysis and market valuation can both use discounted cash flow (DCF) analysis as a tool, the formulation of the DCFs and their interpretation are different."

Nov 1, 2019

By J S. J van Deventer, D C. Shallcross

New developments are taking place in the recovery of gold from leached pulps that are based upon the adsorption of the metal cyanide species onto ion exchange resins. Despite the success of several resin-in-pulp pilot plant operations in the Western World and large-scale plants in the former Soviet Union, the process is yet to gain recognition as a viable alternative to the carbon-in-pulp process. An experimental research program has investigated the use of a variety of different types of resins for the recovery of gold, but to-date no resin studied has the desired properties of high selective loading capacity for gold cyanide and a simple inexpensive elution procedure. In addition very little is known concerning the physical strength of resins and their ability to resist shattering due to osmotic shock during cycles of adsorption and elution. The ability of ion exchange resins to enhance the leaching of refractory and re-adsorbing ores has not been investigated. This paper highlights the necessary factors that need to be addressed before commercialisation of ion exchange technology for gold extraction is feasible.

Jan 1, 1998

By M. Zamalloa, P. J. Mackey, P. Coursol, Y. Prévost

"Over the last decade or so, the availability of commercial thermodynamic modelling packages, such as FactSageTM, have been utilized to help the plant optimize slag chemistry and to minimize slag handling issues that can arise, such as those due to a process upset, for example, by undue feed variability. This paper illustrates an extension of the application of this software in examining a large range of NCV operating parameters, such as the %Fe/SiO2 ratio in the slag and the level of minor gangue components in the slag including CaO, Al2O3, ZnO, MgO, and PbO. The conditions influencing the slag liquidus range of NCV slag are discussed with respect to the overall process chemistry.Given that a sufficiently low %Fe/SiO2 ratio is used in NCV slag, most components such as CaO-ZnOPbO- Al2O3-MgO, in small concentration, all contribute to lowering the NCV slag liquidus. Considering the present level of these minor components, the NCV can operate consistently at 1200°C if the %Fe/SiO2 is between 0.6 and 0.8 in the slag. Using the type of phase diagrams presented in this paper, it is possible to develop different Noranda reactor/Noranda converter operating strategies adapted to the feedstocks available at Xstrata mines/plants or from other sources. The NCV is unique in that a fayalite-based slag is employed for high-efficiency continuous converting with excellent operating results."

Jan 1, 2007

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Ross W. Seedsman

The logical framework recognises that a coal mine roof can be intrinsically stable or may collapse in one of four ways. Suspension of the immediate roof is one of fundamental ground control strategies available to a coal mine engineer and is recommended for three of the four collapse modes. Correctly implemented suspension offers the greatest improvement in roof stability and greatest reduction in longwall risk. For the control of maingates ahead of retreating longwall faces the ideal suspension support (if required) consists of angled, partially debonded, medium-length tendons installed as far behind the development face as practical. For situations where the roof may be subjected to tensile horizontal stress, immediate support by equally spaced short vertical tendons is required. The step away from fully-grouted tendons improves their survivability during the onset of compressive failure in the roof, minimises the risk of isolated loading, and allows a more robust TARP for roof movement. All suspension systems require a strap, sling or truss between the suspension elements.

Jan 1, 2014

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014

By P. I. James, M. R. Baker

This paper examines new copper production from waste-grade ore using Blue Planet Strategies’ DEMET™ (Dynamic Electrode Mining Effluent Treatment) technology, which aims to bridge the practical weak pregnant leach solution (PLS) processing gap in heap leach-solvent extraction/electrowinning (SX/EW) operations by electrochemically removing metals from weak streams and generating product streams strengthened in target metals in a functional analog to SX. Weak PLS treatment was studied and used to estimate the economic and production impacts for a representative hypothetical brownfield copper heap leaching and DEMET-augmented SX/ EW operation to utilize "waste ore." Copper removal at 86% plating efficiency to below 0.1 g/L copper with power consumption of 0.55 kWh/lb copper and product strengths of over 10 g/L copper are presented. Modeling yielded approximately $2/lb total copper production and = $1/lb treatment costs with an immediate operation gross margin increase of 12% for the augmented brownfield. Potential mine life extension with an average 38% gross margin on "waste ore" augmented production at copper values of $3.25/lb was also indicated.

Jan 1, 2014

By Jerome P. Downey

Technologies developed within the field of extractive metallurgy to recover, concentrate, and purify metals and industrial minerals from ores, have served as the foundation for all of the subsequent environmental remediation, materials recycling, and waste management technologies. This paper discusses the application of classical extractive engineering principles to the development of a thermal process for the recovery of mercury from solid wastes. Process development is presented as a series of logical stages, which begin with a thorough characterization of the site-specific waste, move on to bench and pilot scale testing of the process options, and end with a functional process flowsheet. This paper also presents thermodynamic data on many mercury species of interest to the minerals, power, and chemical industries. These data can be used to model the speciation and recovery of the mercury as a function of various process parameters.

Jan 1, 2003

By A. K. Snelgrove

At a time when water resource planning is proceeding on a continental scale, such as the proposed $100 billion North American Water and Power Alliance, which would redistribute water among three nations, including seven provinces of Canada, 35 of the United States, and three States of Mexico, the selection of a single river basin for study may seem to require an apologia. None is offered because of ( 1) the magnitude of the Indus , itself a part of the great Indo-Gangetic Plain drainage system, with Himalayan sources, upon which the thickly populated northern sub-continent of Indo-Pakistan depends for agriculture and hydroelectic power; (2) the extraordinary problems created by dismemberment of the world?s largest irrigation system through legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960; and (3) the herculean effort to contain the twin encroachments of waterlogging and salinization in a basin which faces a shortage of fresh water. The British irrigation system of barrages and canals on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences, due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage.

Jan 1, 1967

By E. Motica

Ores containing uranium and vanadium minerals have been mined from the Salt Wash Member of the Morrison Formation from many localities in the Colorado Plateau region since about 1900. The most productive deposits are in a relatively small area in Southwestern Colorado referred to as the Uravan mineral belt. The mineral belt is a narrow elongate area in which uranium-vanadium deposits in the Salt Wash have a closer spacing, larger size, and higher grade than those in adjoining areas. Pre- 1948 ore production from the mineral belt was 655,000 tons averaging 1.91 per cent V2O5 and 0.28 per cent U3O8. Production during the 1948 to 1964 period was 7,900,000 tons of ore averaging 1.46 per cent V2O5 and 0.27 per cent U3O8. The ore deposits occur principally in the uppermost sandstone unit of the Salt Wash. This unit consists of sandstone lenses formed by a system of aggrading braided streams flowing in an easterly direction generally normal to the mineral belt. These lenses, referred to as channels, are as much as one mile in width and average about 50 feet in thickness and can be traced for several miles along their courses. Areas favorable for one deposits are recognized principally by the following criteria: ( 1) a host sandstone thickness of over 30 feet, (2) the presence of carbonaceous material in the host sandstone, and ( 3) gray mudstones and clays associated with the ore-bearing sandstone. The ore minerals are believed to have been precipitated from laterally migrating solutions; there is no apparent genetic relationship between ore deposits and tectonic structural features. Exploratory and development drilling from the surface is conducted in three phases: first, wide-spaced drilling to find and outline favorable channels; second, moderate-spaced drilling in favorable ground to locate ore deposits; and third, close-spaced drilling to block-out ore. Long-hole drilling from underground stations is used to find and delineate extensions of ore bodies being mined. Due to intense production since 1948 from shallow deposits, best potential for new deposits exists in areas where the ore-bearing unit is 600 to 800 feet deep.

Jan 1, 1968

By H. T. McAdams

The logic of regression analysis as an operations research tool is critically examined, and a formal basis for its application to mining problems is developed. The traditional view of regression analysis as a statistical discipline does not provide an adequate basis for evaluating a regression model in a specific area such as ore reserve calculation or process control. In particular, the validity of the residual-sum-of-squares criterion is questioned, and the need for a criterion based on interpolative features of the model is emphasized. Strictly speaking, a regression model is statistically supported only at points at which observations are available, yet inferences are drawn with regard to a continuum. When considered as a mathematical function, therefore, the model is observationally defined only on a domain consisting of a finite number of points. Extension of this domain to an interval of the real line must be based on physical rather than statistical argument. Vector space and function theory concepts useful as a logical framework for a physically oriented problem analysis are discussed and their usefulness demonstrated in a practical problem.

Jan 1, 1966

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

Low-cost housing, like automobiles, should be appraised in the light not merely of first cost but of upkeep as well. Even more important than the number of miles the family car will go on a gallon of gasoline is the number of days the family home can be kept comfortable on a ton of fuel. A furnace tender who tossed every third shovelful of coal into the ashcan would lose his job promptly, but the effect is the same when homes continue year after year to pour out precious heat through uninsulated roofs and walls, Greater economy in household heating means even more to the national economy than to the individual, especially now that we are preparing for defense. Our fuel resources, although large, should be conserved. If less fuel is used for civilian needs, augmented requirements for defense can be met without unduly increasing the number of men needed at the coal mines and oil ells or adding new producing units that might complicate ultimate readjustment to peacetime conditions when the emergency is past and over-expansion of many industries brings new problems if unnecessary demands for transportation facilities are reduced, public carriers will be able to haul more munitions, and manpower needed for national defense will be released; and by protecting workers from health hazards in their homes additional man-hours of productive effort will be gained. Moreover, reducing the running expenses of houses by proper heat insulation helps home owners to maintain payments on property, and by minimizing foreclosures helps to stabilize the financial structure of the country. In short, here is a situation where the interests of the individual and the Nation are identical and the greatest good for the greatest number is obtained without sacrifice to anyone.

Jan 1, 1941