Search Documents

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By Anthony (Sam) J. S. Spearing

Backfilling using coal waste is not a novel means for waste disposal throughout the world; yet, backfilling using a high density (paste) backfill is relatively new, except in Germany and Poland. One of the main benefits of a high density backfill, as opposed to a low density (slurry) backfill, is that, if placed at a low permeability and low moisture content, the risk of water table contamination can be relatively low. In addition, if paste backfill can be placed cost effectively, environmental benefits are huge because the surface impoundment footprint can be greatly reduced or even eliminated. This is especially true in room-and-pillar applications. In its current state, backfilling is considerably more costly than surface disposal. This is mainly because paste, as opposed to slurry, significantly increases backfill placement costs; however, this could be offset by increasing the achievable extraction rate. Overall, such a system could potentially improve the public?s image of coal mining in the US for a myriad of reasons. This paper discusses a proposed backfill system for a typical room-and-pillar coal mine in the Illinois Basin of the US and clearly shows the technical advantages, although costs are still higher with fill. The cost differential will likely reduce over time, in favor of the backfill option, as costs of traditional surface disposal increase, due mainly to ever-restrictive disposal regulations.

Jan 1, 2013

Alfred Nobel first invented a practical detonator in 1863 and then the blasting cap in 1865. At that time the detonator was used on the end of a length of safety fuse to initiate nitroglycerine-based explosives. Since then the detonator has gone through a number of changes. The instantaneous electric detonator was the first to allow remote firing. The electric delay detonator followed and allowed for timing between holes. In the mid 1970s the NONEL« Tube was invented. This tube combined with NONEL« detonators meant that many of the safety issues, such as stray current and radio frequency, associated with electric delay detonators were eliminated. This system gave the mining industry a reliable and fairly accurate system with which to detonate shots of any size. Since the early 1980s a large amount of research and development work has been done around the world to create a more accurate detonator for the mining and quarrying industry. After years of research, electronic detonators have emerged as the most accurate and precise initiation system available to the mining and quarry industry today. Electronics provide the user with millisecond timing accuracy. The improved level of timing control allows operations to improve fragmentation, throw and reduce vibration levels. There are now a number of different electronic detonator suppliers on the market today. In 2004 Dyno Nobel formed a joint venture called DetNet with AECI. DetNet has a suite of electronic detonators: DigiDet«, HotShot« and QuickShot«. This paper will focus on the HotShot« system, the first of the three new initiation systems to be released to the market in Australia by Dyno Nobel.

Jan 1, 2005

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

Jan 1, 1886

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

By C. Gasparrini

Mineralogy may be applied to the selection of appropriate separation techniques, as well as to assist in the evaluation of problems causing loss of metals and other economically important elements during plant processing. Mineralogic studies may thus help develop techniques to optimize metal recoveries. The present paper describes how such factors as the minerals in which the elements of interest are concentrated, their chemistry, the chemistry of the associated minerals, grain size and textural associations with other minerals in the ore, may affect decisions on separation techniques for the recovery of economic elements. A number of case studies are described in which the mineralogical observation of ore samples has revealed the cause of problems experienced in the extraction of select precious and base metals, or has been decisive in the choice of appropriate techniques for recovery.

Jan 1, 1981

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By Russell E. Griffin

Dielectric constants and dissipation factors were measured for six rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Results for both dry and moist specimens are presented and compared with data reported by others. Loss factors calculated from the data presented are important to the Bureau's study of rock fragmentation by means of dielectric heating.

Jan 1, 1967

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Krawiec Alfons

The threat of rock bursts along with the danger from methane gas and coal dust explosions belongs to particularly dangerous phenomena in Polish pit-coal mines. This phenomenon results mainly from the physical-mechanical properties of the rock mass as well as the geological-tectonic structure of the Upper Silesian Coal Basin. In the postwar years in Polish coal mining thanks to a multi- directional activity, a decrease of rock bursts and their effects has been noted. For example, the number of rock bursts reported in 1965 amounted to 71 in comparison to only 23 in 1974. The ratio of rock bursts calculated for 100,000 tons of coal extracted from rock bursting strata amounted to 0.08 in 1965; however, in 1974 it amounted to 0.023 /Fig. 1/. These results were obtained in face of a continually growing potential threat from rock bursts caused by the systematic increase of extraction from rock bursting strata, exploitation at gradually greater depths along with the extension of exploitation into deposits enclosed in different types of pillars and other parts of deposits surrounded by workings. Despite the achievements of science and mining practice in this field, this threat has not yet been fully studied and controlled as it should be, As a result, research on preventing rock bursts is being continually widened in Poland. This research has a complex, multi-staged and long-range character. Theory, laboratory and field work in the mines are working on a solution to the problem.

Jan 1, 1976

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By William W. Leathen

Acid mine drainage became a reality through the exposure of the first bituminous coal seam, either by man or by nature. At first the small amount of acid formed was quickly and efficiently neutralized by basic rock strata and by neutral or alkaline water. As soon as extensive mining operations overtaxed nature's own defensive measures, acid mine drainage became a problem of concern to government and the coal industry. It was the purpose of the studies conducted at Mellon Institute to accumulate knowledge, both applied and fundamental, relating to the formation and disposal of acid mine effluents. It was during this program that the microbiology of acid mine water was studied. Most bituminous coal mine effluents are highly acidic and contain, along with other ions, high concentrations of ferrous iron. The acid is sulfuric, and. the iron is present as the sulfate; both are the oxidation products of iron sulfides (FeS2) which are present in the form of pyrites, marcasites, or other sulfuritic minerals. The oxidation occurs, in the absence of moisture, according to the following reaction: [ ]

Jan 1, 1959

By J. E. Rouse, D. L. Buchanan

"During the emplacement of the Bushveld Complex in the Potgietersrus area magma reacted with the original floor rocks— Archaean granite or Malmani dolomite and overlying Penge handed ironstone or sedimentary rocks of the Pretoria Series. The complex sequence of sulphide-rich mafic rocks that formed along the contact is known as the Platreef. Associated with the sul­ phide mineralization are important concentrations of platinum-group metals, copper and nickel. Xenoliths of Malmani dolo­ mite have been incorporated into the Platreef and previous work has suggested that anhydrite is likely to have been present in the dolomite. The sedimentarv-derived sulphur thus introduced into the magma exercised an important control on the forma­ tion of the sulphides.Petrographic studies on the Platreef rocks from the Tweefontein area indicate that the original magma reacted with the banded ironstone to form iron-rich pyroxenites. In the Turfspruit area, to the south, the footwall rocks consist of sediments of the Timeball Hill Series. Original argillaceous rocks have been metamorphosed to cordierite-, corundum- and spinel-bearing hornfelses. Graphite was present in the contact zone in both the Tweefontein and Turfspruit areas. Anhydrite-bearing hornfels rocks are also present on Turfspruit.The Platreef rocks that overlie the corundum- and spinel-bearing hornfelses on Turfspruit are peridotitie, and pyroxenites are present in areas underlain by cordierite-bearing hornfels. The absence of orthopyroxene in the peridotite is probably indicative of low silica activity in the original magma. The pyroxenites have, however, undergone silica contamination from the underlying more siliceous cordierite hornfels.Carbon isotope studies indicate that the graphite in the Tweefontein and Turfspruit samples represents organic material orig­ inally associated with the footwall sediments. Sulphur isotope determinations on the anhydrite-bearing floor rocks indicate that this phase is clearly of sedimentary origin and was probably derived from an evaporitic unit within the carbonate sequence. This provides firm support for a model of ore genesis that involved the introduction of additional sulphur into the Bushveld magma. Isotope studies on sulphides associated with the banded ironstone and graphite indicate that these units were not the source of additional sulphur. Experimental studies predict, however, that a magma contaminated with iron- and carbon-rich material would have a high sulphur-carrying capacity. Where additional sulphur is available the magma would achieve saturation early in its crystallization history and precipitate an immiscible sulphide phase. Experimental work has also shown that sulphide precipi­ tation can be triggered by the introduction of salic material into a magma close to sulphur saturation. This mechanism probably played a role in the control of the sulphide mineralization in the Turfspruit area."

Jan 1, 1984

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By C Dowding, C Aimone-Martin, P Abeel

This paper presents measurement and analysis of the dynamic response of a five-storey building to very high frequency excitation (>100 Hz) from blasting vibrations originating from a contiguous excavation of rock. Velocity response measurements in the rock and on the structure were employed to calculate the time-correlated dynamic displacement response of the building to blasting. Time-correlated structure response measurements are needed to advance the understanding of the response of urban structures to high-frequency excitation. Current regulations and understanding are based upon measurements of the response of one- to two-storey residential structures by 10 to 40 Hz excitation. The extension of these observations to taller structures when excited by high-frequency excitation needs to be investigated further.Measurements show that the amplification patterns at the ground level and top of the structure match or are lower than that observed by the US Bureau of Mines (Siskind et al, 1980) for the shorter residential structures. They decrease with increasing peak particle velocity. From the measurements, the global transverse shear strains found by differentiating ground floor and top displacements were calculated to be 12 µstrains. Time-correlated bottom and top of structure displacements show that building response may be more reflective of wave propagation up the structure than whole-structure inter-storey drift.In addition, a 3D model was used to compare computed displacements and strains to measured results. Modelled responses varied considerably, both in magnitude and location of the maximum strain. No conclusion can be made regarding the best 3D model to employ to simulate building response. More data such as motions measured at many points in the structure are needed. Maximum inter-storey transverse shear strains calculated with the model were found through the acceleration excitation and were less than 12 µstrains for 37 mm/s rock motion excitation. The inter-storey transverse shear strains calculated with rock displacement input were less than that found with the acceleration excitation.CITATION:Dowding, C, Aimone-Martin, C and Abeel, P, 2015. Measured and modelled response of a multistory, urban structure to high-frequency blasting excitation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 211–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965