Search Documents

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By M. Herman, G. J. London

A series of dilute Fe-Co alloy specimens were prepared from zone-melted iron. The iron used was given ten floating-zone passes in purified hydrogen. Alloying was accomplished by plating a gradient of metallic cobalt onto a 1/4-in.-diam bar of material from a pure plating bath. The deposit was radioac-tively tagged by a small addition of co80 to the plating bath. Alloy homogenization was accomplished by passing an additional floating-zone pass through the plated section of the bar. The final concentration gradient achieved was from residual to about 1000 ppm (0.1 pct) added Co. After homogenization, the bar was swaged to 0.057 in. wire and cut to tensile specimen blanks 1-1/16 in. long. Each specimen was counted in a well-type scintillation counter. The concentration of cobalt was computed by combining the normalized specimen counting rate with the known weight (measured to the nearest 0.01 mg) of cobalt added during plating. Fig. 1 shows the cobalt gradient obtained, exclusive of residual cobalt which was estimated by neutron-activation analysis to be approximately 50 ppm. Results of recrystallization for 1 hr at 750°, 700°, 650°, and 600°C with specimens containing 40, 170, 470, and 870 ppm added Co are shown in Figs. 2, 3, 4, and 5. Recrystallization was accomplished in a dynamic vacuum of less than 1 x 10 torr. The specimens were mounted and polished parallel to the swaging direction. The recrystallization re- sults show a radical coarsening of structure with increasing cobalt concentration. The coarsest structure obtained was at the 470-ppm level (at all recrystallization temperatures) with a slight grain refinement at the 870-ppm level shown. A more normal solid-solution effect is seen in Fig. 5 (60OoC, 1 hr) where the only specimen completely recrystallized is the one containing 47 ppm Co. Since the possibility existed that some atmosphere-contamination phenomenon might be responsible for the observed results the recrystallization series was repeated using sealed quartz capsules. These were filled with purified argon which was gettered during heat treatment on metallic titanium included in the capsules. The results obtained were essentially the same as shown. Another identical alloy was made using a 5-mm-diam bar of Westinghouse Puron. Specimen preparation and recrystallization treatment were also as described. The results obtained (see Table I) were somewhat erratic. Some coarsening in structure does appear at the highest cobalt concentrations. There is no apparent relationship between the coarse, columnar, directionally solidified structure of the as-melted bars and any of the recrystallized grain structures observed, all of which are much finer than the former structure. A recrystallization process can be most simply described as one of homogeneous nucleation of recrystallized grains in a cold-worked matrix followed by more or less uniform growth of the strain free grain into the cold-worked material.' An impurity element may influence one or both of these processes. Aust and utter' have shown that impurities strongly influence grain boundary mobility in lead. Moreover, definite recrystallization textures are produced by small concentrations of tin,3 while additions of silver or gold4 produce large boundary in-

Jan 1, 1964

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By Schmidt CG

Parameters affecting gold elution using the AARL process are reviewed and critically analyzed in an attempt to optimise metallurgical efficiency and minimise costs in both current and future carbon adsorption operations. Such factors as acid washing, column geometry, elution temperatures and pretreatment reagents are discussed together with eluant water quality and eluate flowrates. Hot acid washing of carbon prior to gold elution has many benefits. Besides improving elution efficiency when eluting with regional water, a hot acid treatment preheats the carbon without causing any gold leakage. Laboratory data indicated that hot acid washing reduces the mass loss of carbon during thermal regeneration. The eluate going to either zinc precipitation or electrowinning is also relatively free of troublesome impurities (organic contaminants and ferrocyanides in particular). Because of the chromatographic character of the AARL elution where an ionic strength gradient is used to inhibit the readsorption of gold, column geometry plays a significant role. While practical considerations and capital costs may restrain the length of the elution column, high length/diameter ratios are advocated in order to promote the plug flow of column eluate. From both a metallurgical and costing viewpoint, the two significant factors affect- ing the AARL gold elution are temperature and cyanide addition. High temperature and high reagent additions within prescribed limits will improve metallurgical efficiencies, but a balance between energy and reagent costs is required in order to minimise overall elution costs. As pretreatment reagents constitute a considerable portion of the total elution costs, both the addition and consumption of sodium cyanide must be carefully considered. Lower cyanide additions may be effective in certain instances, but the more practical use of 0,6 bed volume of a 2-3 per cent NaCN reagent containing 2 per cent NaOH is advocated. This is equivalent to an addition of 20-30 kg NaCN and 20 kg NaOH per ton carbon Treated.

Jan 1, 1986

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.' Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By Richard J. Fruehan

ThE thermodynamic activities of nickel and chromium in liquid Ni-Cr alloys have not been previously reported. There have been several investigations on the solid alloys.1-3 In the present investigation the activity of chromium in liquid Ni-Cr alloys at 1600° C was determined by the use of the following galvanic cell, The use of galvanic cells employing solid oxide electrolytes for determining the activity of metals in solid alloys was first demonstrated by Rapp and Maak4 on Cu-Ni alloys between 700° and 1000°C. Recently Schwerdtfeger5 tested the performance of the ZrO2(CaO) electrolyte at 1600°C and found it satisfactory for oxygen pressures as low as 10"12 atm. He also demonstrated the use of solid oxide electrolytes for determining the activities in liquid metal systems in measuring the activity of manganese in Fe-Mn alloys at 1500°C. Extensive investigations have been carried out in this laboratory, exploring the oxygen partial pressure lower limit at which ZrO2(CaO) electrolyte can be used satisfactorily in oxygen galvanic cells at 1600°C. In a paper to be published at a later date,9 it is demonstrated conclusively that ZrO2(CaO) exhibits insignificant electronic conductivity at oxygen pressures down to about 3 x 10"13 atm which is lower than the oxygen partial pressure in equilibrium with Cr-Cr2O3 at 1600°C. Therefore, the activity of chromium can be related to the measured reversible electromotive force of the cell in the present investigation since no electronic short circulating will occur. Fig. 1 is a schematic diagram of the cell used. The Cr-Cr2O3 electrode was made of equal weights of chromium and Cr2O3 powders which were mixed and packed into a recrystallized alumina crucible. A Pt-wire lead was embedded into the Cr-Cr2O3 compact to insure good contact. A ZrO2(CaO) crucible, supplied by the Zirconium Corp. of America, contained the Ni-Cr melt equilibrated with solid Cr2O3. The ZrO2(CaO) crucible was placed on the Cr-Cr2O3 electrode and additional Cr-Cr2O3 mixture was packed around it. Contact with the Ni-Cr alloy was made with a Cr2O3 tube, which is a weak electronic conductor. A platinum wire lead was attached to the Cr2O3 tube. The galvanic cell was lowered slowly into the hot zone of the furnace tube in order to avoid too large a thermal shock which could break the ZrO2 (CaO) crucible. The furnace was con- tinuously flushed with purified argon during the experiment. The temperature was measured with a Pt-Pt/10 pet Rh thermocouple and maintained at 1600° ± 5°C. The electromotive force was measured with a recording potentiometer. The furnace was turned off when measurements were being made in order to avoid induction effects and the reversibility of the cell was demonstrated in the usual manner. The electromotive force was measured several times over a period of approximately 1 hr. During that period the electromotive force remained constant within ± 3 pet and did not continuously drift in any one direction. After the experiment the alloys were analyzed for chromium in the usual manner. The measured electromotive forces of the cell at 1600°C, (2912°F), are listed in Table I. The activity of chromium, with solid pure chromium as the reference state, (a), was calculated using Eq. [l], , n F E I, n lna RT- U] where E is the measured electromotive force, F is the Faraday constant, and n is equal to 3, the number of equivalents per mole, (nF/RT = 18.59 volts'1 at 1600°C). The resulting activities are listed in Table I. The activity of chromium relative to pure liquid chromium was also calculated. The free energy of fusion of chromium at 1600° C was calculated using

Jan 1, 1969

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been consuming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from conventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "unconventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support industry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas-Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas-bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It appears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 9, 1980

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.&apos; Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By Bob Snashall

Introduction 1300 BC, Egypt. Pharaoh, the god-king, owned all things. He was the only mine operator. As the provider of all things, Pharaoh had great expectations of his officials who gathered the wealth. Pharaoh&apos;s official, the mine foreman, was at a gold mine site to see that royal expectations were met. For the official, it could mean a promotion to the good life here and to the godly life hereafter. When he checked the haul for sufficient progress, a lot was at stake. The miner wore a loincloth, perhaps a headband and, if he was a prisoner, ankle manacles. Only an oil lamp helped illuminate the hot, dusty blackness. A fire at the base of the quartz ore face competed for scarce air. The ore so heated crumbled at the prompting of copper wedges. Confined to a crouch, the miner tossed chunks of ore onto a rope-mesh which, when loaded, was drawn up and lugged out. On the surface, the gold was ground to dust. Then it was transported by donkey caravan to the royal depot. There it was weighed, recorded, and distributed to workshops. Many minerals mined Egypt had gold mines to the south in Nubia and to the east in the desert and Sinai. Indeed, gold underwrote Egypt&apos;s prosperity. With a constant gold supply, fewer hungry hands robbed burial crypts and tombs. Gold was sacred, "the flesh of the gods." The shiny metal financed the army that policed the desert mining routes and guarded the gold caravans from Bedouin marauders. Gold theft was an offense to the gods. Anyone caught with gold `in his lunchpail,&apos; so to speak, could say goodbye to life, both in this world and the next. In addition to gold, Egypt possessed other mined riches that allowed the Egyptian civilization to flourish. From Sinai and Nubia came copper. So abundant was the red metal that it enabled Egypt to become the supreme power, before the advent of iron. Also mined were amethyst, turquoise, feldspar, jasper, carnelian, and garnet. These were used for the rich inlay work that distinguished Egyptian jewelry and cloisonne. But Egypt&apos;s most endurable and awesome material was its stonework - for statues and obelisks and in temples, tombs, and pyramids. Stone quarrying was a vast enterprise. One expedition boasted nearly 10,000 men. These included 5000 laborer soldiers, 130 skilled quarrymen and stonecutters, and - egads! - even 20 scribes. In addition, there were thousands of officials, priests, and officers grooms. There were even fishermen, to provide the multitudes with the catch of the day. Mining methods detailed In 1300 BC, quarrying techniques had changed little since the age of the pyramids some 1300 years before. At that time, in 2600 BC, limestone was locally quarried and fashioned into the blocks of the pyramids. A basic limestone mining method was tunnel quarrying. A ramp was built up to the face of a cliff. A monkey stage was then erected on a ramp. While standing on the stage, quarrymen carved out a rectangular niche in the cliff. The niche was large enough for a quarryman to crawl into. With a wooden mallet, he hammered long copper chisels along the edges of the niche floor to free up the back and sides of the block. The quarryman climbed out of the niche and removed the stage. He then carved out a series of holes in the cliff face for what would be the bottom of the block. The quarryman pounded wooden wedges into the holes. He watered the wedges until they were soaked. The water-logged wedges expanded, splitting the stone along the line of holes. The freed-up block was then levered down from the cliff. On the ground, the blocks were placed on sledges. Men pulled these to nearby water transport. Without block and tackle pulleys, paved roads, and wheels, this was no mean feat. Each block weighed an average of 2.3 t (2.5 st). Whenever possible, the quarrying was done directly from the surface. This "open cast" quarrying also involved using chisels

Jan 2, 1987

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit &apos;flash&apos; chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om&apos;nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.&apos; One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.&apos; By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been con¬suming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from con¬ventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "uncon¬ventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support in¬dustry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas¬Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas¬bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It ap¬pears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 1, 1980

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2&apos;3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By Otto H. Henry, J. J. Cordiano

Though powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread" to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. Purpose of Investigation Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but &apos; such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: 1. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1946

By F. A. Olson, J. S. Cho, M. E. Wadworth

An infrared study of the states of hydration of MgSO4 revealed a hitherto unreported metustable dehydration state in the temperature range just below that of the stable anhydrous salt. Infrared, thermogvavimetric, and X-ray studies indicated that the state had bisulfate and hydroxide characteristics. A formula fitting all of the experimental evidence is hydrogen-bonded Mg(OH)HSO4, or possibly the chemically equivalent 1/2 Mg(HSO4)2. Mg(OH)2 Infrared spectra of the 7, 6, 1, and OH2O states of hydration are given as well as the spectra of the newly found state which is called the bisulfate state in this paper. Thermogvavimetric studies as a function of water-vapor pressure gave an enthalpy value of 16 cal per mole, and 25 eu for the conversion of the bisulfate state to that of the anhydrous salt. The free energies of the transition varied from 1.76 to 0.18 kcal per mole as the transition temperature varied from 279° to 336°C. The bisulfate state is believed to be of importance in catalytic dehydration phenomena using MgSO4 and may be of interest because of properties in sulfating reactions differing from those of the monohydrate. Also, an analogous state may exist as a hydration state of other sulfates. ANHYDROUS magnesium sulfate is a catalyst with a high degree of specificity for the dehydration of secondary alcohols.1&apos;2 The only product obtained at the usual operating temperature range of 360" to 400°C other than the corresponding olefin is water. Thus, the bonding of water to the anhydrous salt as well as an understanding of the hydration states of MgSO4 became of interest in attempting to understand the catalytic mechanism better. In the process of this study using infrared, X-ray, and thermogravimetric analyses a dehydration state not previously reported was found. Proof of its existence, the nature of the state, and its role, if any, in the catalytic mechanism then became of interest. This paper is concerned principally with the first two aspects of this problem. Magnesium sulfate forms many hydrates, of which the monohydrate and heptahydrate (Epsom salts)3 are most important. Other hydrates4 are known with 1-1/4,5 l-1/2, 5 2, 4, 5, 6, and 12 H2O&apos;s. The hydrates with 1-1/4, 1-1/2, 2, 4, and 5 HzO&apos;s are unstable. The anhydrous salt is very stable thermally and has a strong affinity for water. It can be heated without additional decomposition to about 800°C.&apos; At 900°C noticeable decomposition takes

Jan 1, 1964

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2&apos;3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By J. Stuart Warner

The reaction COSO4(c)?CoO(c) + So3(g)was investigated from 950° to 1170OK by two different methods. The sulfate was decomposed in a previously evacuated space and Pso3 calculated from the measured total pressure on the assumption that Pso2 = 2P02. The sulfate was also decomposed under conditions of controlled oxygen pressure. The difference in the results obtained by these experimental techniques is attributed to the effects of thermal diffusion. The standard free energy change for the reaction is given by ?F° = 66,292 + 17.273T log T — 102.57 T (±300 cal/mole). It was found by DTA and X-ray diffraction studies that CoS04 undergoes a transformation at 617°± 4°C. THE metal sulfates may decompose directly to the oxide or pass through one or more intermediate basic sulfates. Provided the oxidation state of the cation does not change in the course of the reaction, the decompositions may be described in general as follows: One of the major objectives of this work was to determine the validity of Eq. [3] as much of the existing sulfate data has been calculated from decomposition pressures by Eq. [5]. The type of apparatus generally used for these measurements consists of a reaction vessel at high temperature which communicates with a manometer at room temperature. A temperature gradient is thus imposed on the gas phase causing thermal diffusion which brings about a partial separation of the different gaseous species present in an initially uniform mixture. The basic theory and experimental facts associated with this phenomenon are summarized elsewhere1 and it will suffice to state here that the heavier gaseous species diffuses down the temperature gradient. Since thermal diffusion destroys the homogeneity of the gas phase, it is not necessarily true that Pso2 = 2Po2 in any particular volume element of the gas phase even though there are twice as many molecules of SO, as of 0, in the gas phase considered as a whole. Under these conditions, the decomposing sulfate gives off SO, which dissociates to SO, and 0, and all three species are distributed throughout the system by thermal diffusion. However, the sulfate will continue to dissociate until the equilibrium value of PSo3 is established on the hot zone. Thermal diffusion may distribute SO2 and O2 throughout the gas phase in any way so long as Eq. [2b] is satisfied in the hot zone; i.e. Pso2(Po2)1/2=K3pso3. When a steady state is reached, we can characterize Pso2 in that

Jan 1, 1962

By C. S. Smith, E. W. Palmer

IN 1934, when Gregg and Daniloffl wrote their excellent monograph on the alloys of iron and copper, the most recent literature on the constitution of the alloys indicated a narrow single-liquid area for 20" above the liquidus with a closed liquid mis-cibility gap above this. Since that time, however, a number of investigators have confirmed the much earlier studies of Mushet2 and Stead3 who, among others in the nineteenth century, had described the true state of affairs. Liquid copper and iron are completely miscible in the absence of carbon, but small amounts of carbon cause liquid segregation. In 1934, one of the writers&apos; mentioned evidence for the absence of liquid separation in carbon-free alloys at temperatures up to 1700°C. Two years later, Mad-docks and Claussen5 unequivocally established the absence of liquid segregation and published a revised diagram, reproduced in fig. 1. They also studied the limits of the two-liquid area in ternary alloys of iron, copper, and carbon as a function of carbon and iron content. In the same year Simpson and Bannister" and Schumacher and Souden7 described in some detail the properties of alloys containing 50 to 75 pct Cu. More recently Hodges et al.16 have developed the copper-rich alloys for use as high-strength conductors. In 1937, Iwase, Okamoto, and Ameniya8 published data on the miscibility gap in ternary alloys of iron, copper, and carbon that supported the conclusions of Maddocks and Claussen, and definitely located the two-liquid area at temperatures of 1450" and 1540°C. They also reported that additions of 1 pct Al, Ni, Pb, Sn, or Zn caused no segregation in 50 pct Cu alloys at 1540°C. The use of copper in amounts approximating 1 pct has found industrial employment to an increasing degree in both wrought and cast steels, for such steels are capable of being precipitation-hardened following normalizing, and have high yield strengths. This is summarized by Gregg and Daniloff,1 Sallitt,9 and Lorig and Adams,10 while Alexander" gives additional information on the heat treatment of copper-steel castings. Lippert12 has described Digby&apos;s two-phase steels containing copper and chromium. The work described in the present paper was done in the years 1932 to 1934, at which time much of the information was new. The excellent work subsequently done in other laboratories but more promptly published makes the present paper in part only a confirmation of what is now well known. There has not, however, been published any unified study of

Jan 1, 1951