Search Documents

By Heinrich Ries

The fusion-point of clay has usually been considered to be influenced chiefly by the quantity of fluxing impurities which the clay contained. Those clays which contain a high percentage of fluxes, such as ferric oxide, lirne, magnesia, and alkalies, fuse at a low temperature. Aside from the percentage of fluxing-impurities, the size of the grains exerts an important influence. Yet, while this fact has, no doubt, been recognized by many, practically no attempts have been made to prove it by actual experiment, although in the case of fire-clays, Prof. H. O. Hofman has rather disputed it. To illustrate the point more clearly, suppose a clay to be made up of a mixture of very refractory grains, such as kaolinite, and some fusible ones. If this clay be heated, the more easily fusible grains will melt first on the surface, and the softening under heat will gradually extend from the surface of the grain to its center. The larger, therefore, the size of the grain, the longer the time required for the heat to penetrate it. Now, if two samples of clay contain the same volume of flux, but of unequal size, the one containing the smaller-sized grains should fuse first, because the fluxing materials are more evenly and thoroughly distributed through the clay, so that they will more or less surround the refractory grains, which tend to act as a framework and hold up the clay-mass when heated. In order to demonstrate the effect of fineness of grain on the fusibility of clay, several mixtures were made up, consisting of white clay and other minerals. The white clay used was a very refractory type from Georgia, the fusion-point of which lay about cone 35 of the Seger series. The mixtures were formed into small bars 1* inches long, and set on a narrow surface, so that the ends were free to bend as soon as the mass softened. They were burned in a Seger gas-furnace.

Jan 1, 1904

By W. H. Andrews

THE constantly increasing consumption of Portland cement in the State makes the above subject of partlcular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case, it may be well ,it this time to consider briefly- the matter of the chemical and physical com-position of proper raw materials. A cement mixture is one that contains approximately 75 per cent. carbonate of lime, 15 per cent. Silica, and 5 to 7 per cent. alumina, and iron oxides; the other elements being magnesium carbonate and small quantities of the rarer elements general associated with limestone deposits. It call be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.-A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina, ratio lies .between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or shales are often found that have the proper physical characteristics but in which the amount of alumina, is too great.

Jan 9, 1913

By W. T. Jr. Thom

IN PREVIOUS classifications of coal, it has been customary to regard moisture eliminated from coal samples between 20° and 100° C. as extraneous matter, rather than as a constituent part of the coal. It seems, however, that the physical character and use properties of the low-rank coals are directly related to the amount of such moisture present, and recent chemical work has shown1 that such coals contain unstable groupings which decompose between 20° C. and temperatures somewhat above 100° C., with the splitting off of moisture. According to this view, the moisture eliminated from air-dried coal below boiling point is similar in all essential respects to moisture eliminated above 100° C., and is produced by analogous reactions; and inasmuch as the moisture given off above 100° C. has always been treated as a constituent of the volatile matter of coal, it would seem that consistent usage would include as a part of the volatile matter all moisture present as an essential component of the coal as it occurs in nature. As a matter of experience, it seems clear that the general physical and chemical characteristics of the low-rank coals are largely determined by or related to the moisture, whether chemically or physically combined, present in air-dried coal; it is also demonstrable by trial that the low-rank coals cannot be satisfactorily classified on a purely chemical basis by using the moisture free form of analysis. The low-rank coals of the western United States include numerous well-defined types, many of which were referred to in a classification proposed by Ashley,2 in which the physical and use properties of the coals were made the primary basis for their systematic grouping. When testing this classification by replotting analyses of these type coals according to the Seyler scheme of classification,3 a satisfactory parallelism between use properties and chemical constitution of the dry coal was found among

Jan 5, 1925

By H. M. Howe

One of the little electric-resistance magnesia crucible-furnaces which I designed for the metallurgical laboratory of the School of Mines of Columbia University is shown, in vertical section, of full natural size, in Fig. 1. The furnace itself consists of two semi-cylinders of magnesia, A A, with a cover of magnesia, B B, and a stopper, C, also of magnesia, which is perforated to admit the leads x, y, of a thermo-electric couple. The furnace is heated by the spiral of platinum wire, D D (entering and departing by the openings I and K), through which a current of any desired strength is passed, bringing it to incandescence, and to ally temperature, not above the melting-point of platinum, which may be desired. The crucible E, actually used in this furnace, is also of magnesia. I have heard of some unsuccessful attempts with furuaces of this general class, and have attributed these failures to the use of siliceous materials for the furnace-walls. Of course such a result is what we should expect, since the silica mould readily be electrolysed by the current, and the resultant silicon would alloy with platinum ; but the little magnesia furnace here clescribed seems to be wholly free from this objection. It has been used in my laboratory for some months, and temperatures, up to 1100° C, hare been developed in it over considerable periods of time—indeed, it has been held near 1400" C. for about two hours—without indication, thus far, of any deterioration of the platinum. In the section shown, F F are a pair of steel disks, bound together, but separated by the inverted thermo-junction, N, of the thermo-electric pyrometer. This arrangement permits the observation and record of retardations in the heating and cooling of F F—in other words, the determinations of the cooling curves of steel—a purpose for which the furnace has been used, thus far, more frequently than in the determination of meltingpoints. For the latter operation, however, it is also suitable.

Jan 1, 1902

By G. L. Craig

COPPER containing a small amount of arsenic has been used extensively abroad, and a number of reports, particularly those by English workers, have indicated that such copper is better suited for certain uses than high-conductivity copper. Inasmuch as a large percentage of the copper fabricated is used for nonelectrical purposes where high conductivity is not at all essential, it has been suggested that arsenical copper might be at least as suitable as high-conductivity copper for many purposes. An investigation spon-sored by the Calumet & Hecla Consolidated Copper Co. at Battelle Memorial Institute was therefore undertaken with the object of determin-ing the effect of small amounts of arsenic (up to 0.75 per cent) on the properties of copper. In this work the effect of arsenic on the basic properties of tough-pitch and of phosphorized copper have been critically studied and many data collected from laboratory experiments which have been supplemented by mill-scale tests. The results of these tests, with coppers of the type referred to, in the annealed condition and after various degrees of reduction, show that the basic properties of copper are not greatly affected by small amounts of arsenic, an increase in strength being observed with increasing arsenic with no corresponding decrease in ductility. It is well known that the evaluation of material for plastic deforma-tion, on the basis of laboratory tests, may not be directly comparable with its performance in commercial operations. In order, therefore, to substantiate the data obtained at the Institute, the cooperation of the Wolverine Tube Co. was obtained for a series of production tests on the fabrication characteristics of phosphorized arsenical copper in the manu-facture of seamless copper tubing. In these tests the behavior of the arsenical coppers was carefully observed in comparison with that of representative types of phosphorized arsenic-free copper, which were fabricated under the same conditions.

Jan 1, 1933

By W. P. Frey

THE briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.1 It has passed. the stage of experiment and now rests,, on a foundation practically and financially sound. The purpose of this paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93 11,160 B.t.u. 17,500 X 0.07 1,125 B.t.u. Total 12,355 B.t.u. per pound of briquets

Jan 1, 1918

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By A. S. Koster, G. D. Rieck

X-ray experiments were carried out to show the occurrence of cylindrical texture in drawn tungsten wire. Only a small amount of (110) (110) cylindrical texture could he found in wires of intermediate thickness, i.e., of about 1.5 mm diameter. DRAWN wires of tungsten and other bcc metals like iron and molybdenum show a well-established (110) fiber texture. Now it might be conceivable that in drawing radial stresses remove the randomness of the crystallites around the [110} axis, thus giving a fiber texture of higher symmetry. In the resulting so-called cylindrical textures a specified plane normal coincides with the radius of the wire. Several authors discuss the occurrence of cylindrical textures in bcc metals. ~ieck' found no cylindrical texture in drawn tungsten wires of 165 n diameter. Leber~ states that in tungsten wires of 3 mm diameter a cylindrical {100)(110) texture is developed, which is gradually converted to a normal fiber texture by subsequent drawing. He also reported a definite cylindrical texture at the surface of iron wires. Peck and Thomas3 observed a nonuniform mode of deformation of the grains in transverse sections of heavily drawn tungsten and iron wires. According to Bhandary and cullity4 a swaged iron wire has neither a perfect (110) fiber texture nor a perfect {100}(110) cylindrical texture. It is clear that the concept of cylindrical texture in bcc metals still lacks a firm experimental basis. Leber's eviden~e,~ which seems to be the strongest, rests upon qualitative interpretation of photographs. The appearance of the 110 and 200 lines on the photograph of 3-mm wire, however, can be very well attributed5 to a normal ( 110) fiber texture superimposed on random background; our Fig. 1, giving a Debye-Scherrer diagram of etched tungsten wire of 180 p, is free of cylindrical texture according to all authors, but is quite similar to Leber's diagram. It was therefore decided to use a different method of X-ray texture determination on tungsten wires of diameters where cylindrical textures may be expected.

Jan 1, 1965

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

AT THE beginning of December, the Lausanne Con-ference was in session. The representatives of the United States declared the American position. The representatives of Russia were received and were heard. The Turks appeared at this conference in the attitude of victors, dictating terms. The British refused to surrender Mosul, and December thus ended with this question unsettled. Early in the month the premiers of the principal powers met in London for the discussion of the German reparations question, the temporary agreement expiring on. Jan. 15, 1923. On Dec. 11 the Conference adjourned without getting anywhere, and at the end of December prospects looked more hopeless than ever. The premiers are to meet again on Jan. 2, 1923. The interruption of the London conference was followed by the intimation of early participation of the United States in European affairs in the practical way of a large loan to Germany. These intimations, ema-nating from Washington, appear to have been in the nature of trial balloons. They showed that the wind was unfavorable, the bankers not considering conditions suitable for the flotation of such a loan. British statisticians are puzzled by the fact that the trade returns of Great Britain show a greater turnover in the volume of goods during the first 11 months of 1922 than in 1920, although the rate of labor employ-ment in 1920 was nearly 100 per cent. and in 1922 only about 86 per cent., with an economic situation admit-tedly so bad as to be alarming. The British Parliament was convened under the premiership of Bonar Law. One of its first acts was confirmation of the constitution of the Irish Free State. Civil war in Ireland continued. Poland, like most of the other countries of Europe, is torn between socialism and conservatism, with the former party at present predominant. Early in December, Gabriel Narutowicz, an engineer but a radical, was elected president. On Dec: 14 he entered office and-on Dec. 16 he was assassinated.

Jan 1, 1923

THE Bergbüchlein and Probierbüchlein occupy a unique position in the literature of mining and metallurgy, for, they are the first printed books on any aspect of the two related professions. The first printed book on any subject has an allure that may not be entirely warranted by the strict historical significance of its contents. Among the books of the first century of printing there are very few that contain information that was new at the time of publication. Much' of what they recorded had been previously circulated in manuscript form. Printed books are nevertheless of great value because they mark the time when the author's words, free from errors-or at least with the same errors-became available to large numbers, of readers, who thus could easily and cheaply acquire a common background for their future work. Moreover, though there is occasionally some doubt as to the exact year of publication'(as in the case of the present works), it is generally easier to date a printed work than a manuscript, and thus to provide a fixed coördinate in history. The Bergbüchlein, "The Little Book on Ores," is the first printed work in the field of mining. It is an introduction to mining geology, which means that it was not addressed to the practicing expert but was intended to rouse the interest of beginners in the various aspects of a future vocation. It touches on the theories of the generation of ores, introduces and defines some of the most frequently encountered technical terms of the profession, and indicates what knowledge and tools are required for successful prospecting and mining. It also describes the ores of the seven most important metals. For those parts that deal with theory the author accepted uncritically the traditional teachings of the alchemists and the astrologers; his hints on where to find promising ores are based partly on superstition; but, there is enough factual,

Jan 1, 1949

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

MEASUREMENTS of the solubility of scandium in liquid cadmium from 349" to 606°C by Chasanov, Hunt, Johnson, and eder' led to the isolation and characterization of the intermetallic compound ScCQ. The solid phase found in equilibrium with a saturated solution of scandium in liquid cadmium above 422°C is ScCQ. The equilibrium solid phase below this temperature has not as yet been characterized. Hexagonal needles of ScCG were isolated from a 5 wt pct Sc alloy which had been ice-quenched from 500°C. Free cadmium was leached away from the intermetallic with saturated ammonium nitrate solution. The concentration of cadmium in successive leaches was followed polarographically and the leaching process was terminated when the rate of cadmium dissolution decreased markedly. Chemical analysis of the intermetallic thus isolated is as follows: 11.5 wt pct Sc and 88.3 wt pct Cd. The composition of ScCQ is 11.8 wt pct Sc and 88.2 wt pct Cd. X-ray diffraction powder photographs of ScCds taken in a 114.6-mm Debye-Scherrer camera with CuKa, radiation can be indexed on the basis of a hexagonal nit cell. Lattice coonstants are a. = 6.330 ± 0.001A to 6.324 i 0.001A and co = 4.853 i 0.001A. The a0 has a slight range with the lower value seemingly associated with the cadmium-rich terminus of the phase. With eight atoms in the unit cell the calculated intermetallic density is 7.54 g per cu cm; the density as determined by a liquid-displacement method is 7.7 g per cu cm. Powder-diffraction data for ScCQ are recorded in Table I. Stoichiometry, symmetry, unit-cell dimensions, and the number of atoms per unit cell indicate the MgsCd (D019) type structure for ScCQ; space group is D,&-P6,/mmc. Atomic coordinates are:

Jan 1, 1964

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel colltent is low enough to permit the slimes to proceed to the dorè furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfartory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. . It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1943

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1938

By Frederic Benard

This paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the dore furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefork was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1944

By Morris Muskat

In preparing a well for pumping, observations are often made of the fluid level in the well bore or bottom-hole pressures at various times before equilibrium has set in. From a qualitative point of view one may immediately infer that if the rise in the bottom-hole pressure or fluid level is rapid the permeability of the sand about the well bore is large, and converse conclusions may be drawn if the rise is slow. However, a more quantitative estimate will give additional information of value, as will be shown in this paper. To derive such an estimate we may proceed as follows. Let h be the fluid height, above the sand face, at time t, and let yo be the average density of the fluid that enters the bore. The bottom-hole pressure, for a fluid height h will therefore be p = rogh, neglecting, of course, the friction drop in the well bore, while the fluid is rising, as may be justifiably done for most pumping wells. If a is the free area of the open-flow string—assumed to be uniform— the rate of production from the sand during the rise of fluid will be: where the last part of the equation merely indicates that, in general, the production rate Q must be considered as a function of the back pressure, and is determined by it alone. In fact, equation 1 shows that if the rate of rise of the pressure or fluid level is determined as a function of the height of rise, or p, for a number of values of the latter, this functional relation between Q and p will be immediately given. Conversely, if we know this functional relation, the rate of increase of p or h may be predicted, or, by observing the rate of rise of p or h some of the constants of the sand may be determined. Thus we may approximate the production from a well in a pumping state by that of a dead

Jan 1, 1937

By J. King Hoyt

IN both Sweden and England rapid progress is being made in metallurgical development, and the steel industry in both countries is distinctly on the mend. There has been some industrial trouble in Sweden in the iron mines and the wood pulp mills, but at the same time all the steel works have a sufficient stock of pig iron and ore to continue their operations for many months to come. Consequently the strike, unless long protracted, will not affect the output of steel in Sweden. Several of the steel manufacturers in Sweden, most notably Forsbacka and Sandviken, have been very suc-cessful recently in securing large orders, particularly from the continent, for ball-bearing steel, both hollow and solid. Whereas some years ago they ran into-se-rious competition with the German mills, the quality of the steel from these Swedish mills is such that they are now firmly established, and are selling some of the lead-ing manufacturers of bearings on the Continent, as well as automobile manufacturers. The secret of their success seems to lie in a better selection of ores, in more careful control of blast-fur-nace operations and better equipment. Rule of thumb in steel making is taboo, and strict reliance is placed on the laboratory. They are constantly experimenting, and metallurgists and chemists are sent to different countries for study and investigation. In their native ores they have, of course, a unique advantage in pos-sessing iron ores extraordinarily free from phosphorus. At Forsbacka, they are not content with the ordinary chemical analysis of the ingot; but also test the physical properties, as well as make metallographic investiga-tions for slag inclusions, segregations and oxides. In both England and Sweden they watch the nitrogen con-tent of the steel very carefully, a feature which does not appear in the ordinary analysis. In testing carbon, they do not use the color test, but employ an electric .induction device.

Jan 7, 1928

By T. D. Yensen

Discussion of the paper of T. D. YENSEN, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 483 to 512. JOHN A. MATHEWS, Syracuse, N. Y.-Concerning the critical composition of the steel containing 2.50 per cent. of silicon, I may say that 12 or 13 years ago we made some of these alloys. They. were not as pure as the alloys made by Mr. Yensen, nor were they melted in vacuo, but one of them contained exactly 2.50 per cent. silicon, and about 0.25 per cent. carbon. It gave us no trouble whatever in hammering to a billet or rolling into bars, nor even when rolling into ¼ -in. wire rods. The steel in question was practically free from everything except carbon or silicon and contained no manganese sulphur or phosphorus worth mention. The alloy containing 2.50 per cent. of silicon worked perfectly well, as well as one containing 0.5 per cent. silicon, and it seems to me that further work should be done by Mr. Yensen on the physical properties of alloys at this seemingly critical change point. W. E. -RUDER, Schenectady, N. Y.-We -have made silicon steels of practically every composition and have never obtained any material under 5 or 6 per cent. of silicon which was brittle. This may be due, of course, to the presence of carbon, in some of the 'commercial materials, and I presume that Mr. Yensen would argue that the: presence of this carbon might prevent inter-granular brittleness. However, all of our silicon steels, up to 5 per cent. of silicon, by treatment in hydrogen at temperatures near the melting point, can be made to show inter-granular brittleness. Furthermore, the material made brittle in this way could be restored by treating at the same temperature in hydrogen containing a hydrocarbon vapor. I discussed this matter some years ago in a paper on inter-granular cement. It therefore appears likely to me that Mr.

Jan 5, 1916

By Sir Robert Hadfield

Table 1 gives the composition of the specimens listed by the author. The details of test procedure and the results of the tests on mechanical, magnetic and electrical properties and cor-rodibility of the alloys are published in full in a paper by the same author, "Alloys of Iron and Manganese Containing Low Carbon," presented before the Iron and Steel Institute (of Great Britain) and published in full in their Proceedings for 1927, to which reference should be made. After reporting these tests the author gives the following discussion of results:] The studies here reported do not indicate that any of the series has really valuable or useful qualities for industrial applications, though the demands of industry are so varied that it is unsafe to prophesy that no special use will be found for a given material. The non-magnetic property of manganese steel is due to the association of Fe and Mn, but carbon has also an effect, enabling non-magnetic qualities to be obtained with a much lower percentage of Mn than would otherwise be the case; for example, 16 per cent. Mn is necessary for alloys practically free from carbon, while with 1 per cent. C nonmagnetic alloys may be obtained with as little as 7 per cent. Mn. Carbon, however, is the prime cause of the development of magnetic qualities by heat treatment. (Sec section 8 of the paper referred to above.) These Fe-Mn alloys show a resistance up to 87 microhms per c. c., but. as there are other alloys which have a resistance as high as 130 microhms per C. c., this does not provide any new feature of value. The most marked feature of the series studied is the brittleness in the range 3 to 10 per cent., with a maximum of brittleness at 7 per cent. Material with this percentage, while possessing quite appreciable hard-

Jan 1, 1927

By J. L. Gissy, G. H. Schippereit, J. B. Schroder

THE existence of mechanical anisotropy in hexagonal metals is well known.' One possible method of measuring the degree of anisotropy in a metal is to make hardness measurements on the different planes of a single crystal. So far as is known, no single-crystal hardness data have been reported in the literature for alpha titanium. To obtain an estimate of the variation in hardness with crystallographic direction in titanium, Knoop hardness measurements were made on single crystals of electrorefined alpha titanium obtained from the Bureau of Mines, Boulder City, Nev. The hardness of arc-melted ingots prepared from this material was 64 Bhn (1000-kg load, 30 sec). Crystals of sufficient size were mounted in epoxy resin with the basal plane exposed. They were then polished and etched to remove excess plastic resin and work-hardened surface material. The crystals were then examined by x-ray diffraction, using the back-reflection Laue technique to insure that the crystals were properly oriented and strain free. After Knoop hardness readings (100 or 200-g load) were taken on the exposed surface, the crystals were remounted to expose a prismatic face and the foregoing procedure was repeated. Hardness values for various orientations are listed in Table I. The data show a difference between the hardness of the basal planes and that of the prismatic planes, as anticipated. More striking is the hardness difference observed between different orientations of the indentor on the prismatic planes as shown in Table I and Fig. 1. All of the indentations shown in Fig. 1 were made with a 100-g load. The long axis of indentation A is parallel to the unique (c) axis of the crystal. The deformation marks visible around indentations A and C of Fig. 1 are probably slip traces of the (10.0) system reported by Rosi, et al. The greater hardness observed when the long axis of the indentor was perpendicular to the unique axis of the crystal (indention B) is probably caused by the opera-

Jan 1, 1959